[ Upstream commit fe418231b1 ]
Fix detection of BREAK on sunsab serial console: BREAK detection was only
performed when there were also serial characters received simultaneously.
To handle all BREAKs correctly, the check for BREAK and the corresponding
call to uart_handle_break() must also be done if count == 0, therefore
duplicate this code fragment and pull it out of the loop over the received
characters.
Patch applies to 3.16-rc6.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5cdceab3d5 ]
Fix regression in bbc i2c temperature and fan control on some Sun systems
that causes the driver to refuse to load due to the bbc_i2c_bussel resource not
being present on the (second) i2c bus where the temperature sensors and fan
control are located. (The check for the number of resources was removed when
the driver was ported to a pure OF driver in mid 2008.)
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 081e83a78d ]
Macvlan devices do not initialize vlan_features. As a result,
any vlan devices configured on top of macvlans perform very poorly.
Initialize vlan_features based on the vlan features of the lower-level
device.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c36c9d50cc ]
The recent commit "e29aa33 bna: Enable Multi Buffer RX" is causing
a performance regression. It does not properly update 'cmpl' pointer
at the end of the loop in NAPI handler bnad_cq_process(). The result is
only one packet / per NAPI-schedule is processed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d92f5dec63 ]
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73f156a6e8 ]
Ideally, we would need to generate IP ID using a per destination IP
generator.
linux kernels used inet_peer cache for this purpose, but this had a huge
cost on servers disabling MTU discovery.
1) each inet_peer struct consumes 192 bytes
2) inetpeer cache uses a binary tree of inet_peer structs,
with a nominal size of ~66000 elements under load.
3) lookups in this tree are hitting a lot of cache lines, as tree depth
is about 20.
4) If server deals with many tcp flows, we have a high probability of
not finding the inet_peer, allocating a fresh one, inserting it in
the tree with same initial ip_id_count, (cf secure_ip_id())
5) We garbage collect inet_peer aggressively.
IP ID generation do not have to be 'perfect'
Goal is trying to avoid duplicates in a short period of time,
so that reassembly units have a chance to complete reassembly of
fragments belonging to one message before receiving other fragments
with a recycled ID.
We simply use an array of generators, and a Jenkin hash using the dst IP
as a key.
ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it
belongs (it is only used from this file)
secure_ip_id() and secure_ipv6_id() no longer are needed.
Rename ip_select_ident_more() to ip_select_ident_segs() to avoid
unnecessary decrement/increment of the number of segments.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92c14bd947 upstream.
This is only relevant to implementations with multiple clusters, where clusters
have separate clock lines but all CPUs within a cluster share it.
Consider a dual cluster platform with 2 cores per cluster. During suspend we
start hot unplugging CPUs in order 1 to 3. When CPU2 is removed, policy->kobj
would be moved to CPU3 and when CPU3 goes down we wouldn't free policy or its
kobj as we want to retain permissions/values/etc.
Now on resume, we will get CPU2 before CPU3 and will call __cpufreq_add_dev().
We will recover the old policy and update policy->cpu from 3 to 2 from
update_policy_cpu().
But the kobj is still tied to CPU3 and isn't moved to CPU2. We wouldn't create a
link for CPU2, but would try that for CPU3 while bringing it online. Which will
report errors as CPU3 already has kobj assigned to it.
This bug got introduced with commit 42f921a, which overlooked this scenario.
To fix this, lets move kobj to the new policy->cpu while bringing first CPU of a
cluster back. Also do a WARN_ON() if kobject_move failed, as we would reach here
only for the first CPU of a non-boot cluster. And we can't recover from this
situation, if kobject_move() fails.
Fixes: 42f921a6f1 (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Reported-and-tested-by: Bu Yitian <ybu@qti.qualcomm.com>
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44fa816bb7 upstream.
nr_dirty is updated without locking, causing it to drift so that it is
non-zero (either a small positive integer, or a very large one when an
underflow occurs) even when there are no actual dirty blocks. This was
due to a race between the workqueue and map function accessing nr_dirty
in parallel without proper protection.
People were seeing under runs due to a race on increment/decrement of
nr_dirty, see: https://lkml.org/lkml/2014/6/3/648
Fix this by using an atomic_t for nr_dirty.
Reported-by: roma1390@gmail.com
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8c712ea47 upstream.
1d3d4437ea ("vmscan: per-node deferred work") added a flags field to
struct shrinker assuming that all shrinkers were zero filled. The dm
bufio shrinker is not zero filled, which leaves arbitrary kmalloc() data
in flags. So far the only defined flags bit is SHRINKER_NUMA_AWARE.
But there are proposed patches which add other bits to shrinker.flags
(e.g. memcg awareness).
Rather than simply initializing the shrinker, this patch uses kzalloc()
when allocating the dm_bufio_client to ensure that the embedded shrinker
and any other similar structures are zeroed.
This fixes theoretical over aggressive shrinking of dm bufio objects.
If the uninitialized dm_bufio_client.shrinker.flags contains
SHRINKER_NUMA_AWARE then shrink_slab() would call the dm shrinker for
each numa node rather than just once. This has been broken since 3.12.
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61bd55ce16 upstream.
When creating the demux table we need to iterate over the selected scan mask for
the buffer to get the samples which should be copied to destination buffer.
Right now the code uses the mask which contains all active channels, which means
the demux table contains entries which causes it to copy all the samples from
source to destination buffer one by one without doing any demuxing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b2a4d35a6 upstream.
val2 should be zero
This will make no difference for correct inputs but will reject
incorrect ones with a decimal part in the value written to the sysfs
interface.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 381676d5e8 upstream.
The userspace interface for acceleration sensors is documented as using
m/s^2 units [Documentation/ABI/testing/sysfs-bus-iio]
The fullscale raw values for the BMA80 corresponds to -/+ 1, 1.5, 2, etc G
depending on the selected mode.
The scale table was converting to G rather than m/s^2.
Change the scaling table to match the documented interface.
See commit 71702e6e, iio: mma8452: Use correct acceleration units,
for a related fix.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6328a07bd upstream.
The acpi_pnp_match() function is used for finding the ACPI device
object that should be associated with the given PNP device.
Unfortunately, the check used by that function is not strict enough
and may cause success to be returned for a wrong ACPI device object.
To fix that, use the observation that the pointer to the ACPI
device object in question is already stored in the data field
in struct pnp_dev, so acpi_pnp_match() can simply use that
field to do its job.
This problem was uncovered in 3.14 by commit 202317a573 (ACPI / scan:
Add acpi_device objects for all device nodes in the namespace).
Fixes: 202317a573 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Reported-and-tested-by: Vinson Lee <vlee@twopensource.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aa0abed3a upstream.
byReAssocCount is incremented every second resulting in
disassociated message being send every 10 seconds whether
connection or not.
byReAssocCount should only advance while eCommandState
is in WLAN_ASSOCIATE_WAIT
Change existing scope to if condition.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89fb4cd1f7 upstream.
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0193ed8225 upstream.
This is a bug fix for the situation when function tsi721_desc_get() fails
to obtain a free transaction descriptor.
The bug usually results in a memory access crash dump when data transfer
scatter-gather list has more entries than size of hardware buffer
descriptors ring. This fix ensures that error is properly returned to a
caller instead of an invalid entry.
This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Stef van Os <stef.van.os@prodrive-technologies.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c01fac1c77 upstream.
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aff008ad81 upstream.
Commits 9ec36ca (of/irq: do irq resolution in platform_get_irq)
and ad69674 (of/irq: do irq resolution in platform_get_irq_byname)
change the semantics of platform_get_irq and platform_get_irq_byname
to always rely on devicetree information if devicetree is enabled
and if a devicetree node is attached to the device. The functions
now return an error if the devicetree data does not include interrupt
information, even if the information is available as platform resource
data.
This causes mfd client drivers to fail if the interrupt number is
passed via platform resources. Therefore, if of_irq_get fails, try
platform_get_resource as method of last resort. This restores the
original functionality for drivers depending on platform resources
to get irq information.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rob Herring <robh@kernel.org>
[ Guenter Roeck: backported to 3.15 ]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
commit 1b2c4869d8 upstream.
This is a halfway fix for hawaii acceleration. More fixes to come
but hopefully isolated to userspace.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8c214d22e upstream.
We must mask out the overflow bit as well, otherwise
the wptr will never match the rptr again and the interrupt
handler will loop forever.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edffe1b626 upstream.
Do not split the PARPORT-related symbols with the new kconfig
symbol ARCH_MIGHT_HAVE_PC_PARPORT. The split was causing incorrect
display of these symbols -- they were not being displayed together
as they should be.
Fixes: d90c3eb315 "Kconfig cleanup (PARPORT_PC dependencies)"
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 043572d544 upstream.
Temperature limit clamps are applied after converting the temperature
from milli-degrees C to degrees C, so either the clamp limit needs
to be specified in degrees C, not milli-degrees C, or clamping must
happen before converting to degrees C. Use the latter method to avoid
overflows.
vrm is an u8, so the written value needs to be limited to [0, 255].
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 50c5d36dab upstream.
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b32bfc06ae upstream.
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1871ee134b upstream.
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2 ("libata/ahci: accommodate tag ordered controllers")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db4175ae20 upstream.
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3445857b22 upstream.
When the audio encoding is changed the driver calls hdpvr_set_audio
with the current opt->audio_input value. However, that should have
been opt->audio_input + 1. So changing the audio encoding inadvertently
changes the input as well. This bug has always been there.
The second bug was introduced in kernel 3.10 and that broke the
default_audio_input module option handling: the audio encoding was
never switched to AC3 if default_audio_input was set to 2 (SPDIF input).
In addition, since starting with 3.10 the audio encoding is always set
at the start the first bug now always happens when the driver is loaded.
In the past this bug would only surface if the user would change the
audio encoding after the driver was loaded.
Also fixes a small trivial typo (bufffer -> buffer).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Scott Doty <scott@corp.sonic.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f71920efb1 upstream.
Wrong value used in same cases for the aspect ratio.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4856fbd12d upstream.
The OMAP4 camera support depends on I2C and VIDEO_V4L2, both
of which can be loadable modules. This causes build failures
if we want the camera driver to be built-in.
This can be solved by turning the option into "tristate",
which unfortunately causes another problem, because the
driver incorrectly calls a platform-internal interface
for omap4_ctrl_pad_readl/omap4_ctrl_pad_writel.
Instead, this patch just forbids the invalid configurations
and ensures that the driver can only be built if all its
dependencies are built-in.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc271ee0d0 upstream.
Firmware folks seem say that this flag can make trouble.
Drop it. The advantage of CTS to self is that it slightly
reduces the cost of the protection, but make the protection
less reliable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 048e5a07f2 upstream.
The block size for the dm-cache's data device must remained fixed for
the life of the cache. Disallow any attempt to change the cache's data
block size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aec8629ec upstream.
The block size for the thin-pool's data device must remained fixed for
the life of the thin-pool. Disallow any attempt to change the
thin-pool's data block size.
It should be noted that attempting to change the data block size via
thin-pool table reload will be ignored as a side-effect of the thin-pool
handover that the thin-pool target does during thin-pool table reload.
Here is an example outcome of attempting to load a thin-pool table that
reduced the thin-pool's data block size from 1024K to 512K.
Before:
kernel: device-mapper: thin: 253:4: growing the data device from 204800 to 409600 blocks
After:
kernel: device-mapper: thin metadata: changing the data block size (from 2048 to 1024) is not supported
kernel: device-mapper: table: 253:4: thin-pool: Error creating metadata object
kernel: device-mapper: ioctl: error adding target to table
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6938ad40cb upstream.
These two function's switch case lack the 'break' that make them always
return error.
Signed-off-by: Ted Juan <ted.juan@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ac66effe7 upstream.
In some cases we fetch the edid in the detect() callback
in order to determine what sort of monitor is connected.
If that happens, don't fetch the edid again in the get_modes()
callback or we will leak the edid.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbb60fe35a upstream.
Return IRQ_NONE if it was not our irq. This is necessary for the case
when qxl is sharing irq line with a device A in a crash kernel. If qxl
is initialized before A and A's irq was raised during this gap,
returning IRQ_HANDLED in this case will cause this irq to be raised
again after EOI since kernel think it was handled but in fact it was
not.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 201bb62402 upstream.
If the value in the scratch register is 0, set it to the
max level. This fixes an issue where the console fb blanking
code calls back into the backlight driver on unblank and then
sets the backlight level to 0 after the driver has already
set the mode and enabled the backlight.
bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=81382https://bugs.freedesktop.org/show_bug.cgi?id=70207
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: David Heidelberger <david.heidelberger@ixit.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29e697b118 upstream.
Certain GIC implementation, namely those found on earlier, single
cluster, Exynos SoCs, have registers mapped without per-CPU banking,
which means that the driver needs to use different offset for each CPU.
Currently the driver calculates the offset by multiplying value returned
by cpu_logical_map() by CPU offset parsed from DT. This is correct when
CPU topology is not specified in DT and aforementioned function returns
core ID alone. However when DT contains CPU topology, the function
changes to return cluster ID as well, which is non-zero on mentioned
SoCs and so breaks the calculation in GIC driver.
This patch fixes this by masking out cluster ID in CPU offset
calculation so that only core ID is considered. Multi-cluster Exynos
SoCs already have banked GIC implementations, so this simple fix should
be enough.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Fixes: db0d4db22a ("ARM: gic: allow GIC to support non-banked setups")
Link: https://lkml.kernel.org/r/1405610624-18722-1-git-send-email-t.figa@samsung.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 144cb08864 upstream.
Commit 3ab72f9156 "dt-bindings: add GIC-400 binding" added the
"arm,gic-400" compatible string, but the corresponding IRQCHIP_DECLARE
was never added to the gic driver.
Therefore add the missing irqchip declaration for it.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed additional empty line and adapted commit message to mark it
as fixing an issue.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Fixes: 3ab72f9156 ("dt-bindings: add GIC-400 binding")
Link: https://lkml.kernel.org/r/2621565.f5eISveXXJ@diego
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
commit a97e8027b1 upstream.
Patch 0a68214b "ARM: DT: Add binding for GIC virtualization extentions (VGIC)" added
the "arm,cortex-a7-gic" compatible string, but the corresponding IRQCHIP_DECLARE
was never added to the gic driver.
To let real Cortex-A7 SoCs use it, add the necessary declaration to the device driver.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lkml.kernel.org/r/1404388732-28890-1-git-send-email-matthias.bgg@gmail.com
Fixes: 0a68214b76 ("ARM: DT: Add binding for GIC virtualization extentions (VGIC)")
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d76744a932 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=70191https://bugzilla.kernel.org/show_bug.cgi?id=77581
It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.
The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.
Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com>
Reported-by: Linus Gasser <list@markas-al-nour.org>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2a6c7813f ]
Huawei's usage of the subclass and protocol fields is not 100%
clear to us, but there appears to be a very strict system.
A device with the "shared" device ID 12d1:1506 and this NCM
function was recently reported (showing only default altsetting):
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 3
bInterfaceProtocol 22
iInterface 8 CDC Network Control Model (NCM)
** UNRECOGNIZED: 05 24 00 10 01
** UNRECOGNIZED: 06 24 1a 00 01 1f
** UNRECOGNIZED: 0c 24 1b 00 01 00 04 10 14 dc 05 20
** UNRECOGNIZED: 0d 24 0f 0a 0f 00 00 00 ea 05 03 00 01
** UNRECOGNIZED: 05 24 06 01 01
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 9
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4b70a07ed ]
Nothing cleans up the objects created by
vnet_new(), they are completely leaked.
vnet_exit(), after doing the vio_unregister_driver() to clean
up ports, should call a helper function that iterates over vnet_list
and cleans up those objects. This includes unregister_netdevice()
as well as free_netdev().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 548d28bd0e ]
Obvious copy/paste error when I converted the ad_select to the new
option API. "lacp_rate" there should be "ad_select" so we can get the
proper value.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Fixes: 9e5f5eebe7 ("bonding: convert ad_select to use the new option
API")
Reported-by: Karim Scheik <karim.scheik@prisma-solutions.at>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a8a3e41c67 ]
The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():
/*
* hdrlen includes the 2-byte PPP protocol field, but the
* MTU counts only the payload excluding the protocol field.
* (RFC1661 Section 2)
*/
mtu = pch->chan->mtu - (hdrlen - 2);
However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.
In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)
Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:
2948 (echo payload)
+ 8 (ICMPv4 header)
+ 20 (IPv4 header)
---------------------
2976 (PPP payload)
These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:
1489 (PPP payload)
+ 4 (MP header)
+ 2 (PPP protocol field for the MP payload (0x3d))
+ 6 (PPPoE header)
--------------------------
1501 (Ethernet payload)
This packet exceeds the link MTU and is discarded.
If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A
ping -s 2948 -c 1 192.168.15.254
leads to the smaller fragment that is correctly received on the server side:
(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
Flags [end], length 1492
and to the bigger fragment that is not received on the server side:
(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1515: PPPoE [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
Flags [begin], length 1493
With the patch below, we correctly obtain three fragments:
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
length 1514: PPPoE [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
length 27: PPPoE [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
Flags [end], length 5
And the ICMPv4 echo request is successfully received at the server side:
IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
length 2976)
192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
length 2956
The bug was introduced in commit c9aa689537
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.
Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4cad9f3b61 ]
On BE3, if the clear-interrupt bit of the EQ doorbell is not set the first
time it is armed, ocassionally we have observed that the EQ doesn't raise
anymore interrupts even if it is in armed state.
This patch fixes this by setting the clear-interrupt bit when EQs are
armed for the first time in be_open().
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0a19858794 ]
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
