commit 9cc6d9e5da upstream.
Joachim Eastwood reports that commit fbfb872f5f "ARM: 8148/1: flush
TLS and thumbee register state during exec" causes a boot-time crash
on a Cortex-M4 nommu system:
Freeing unused kernel memory: 68K (281e5000 - 281f6000)
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
task: 29834000 ti: 29832000 task.ti: 29832000
PC is at flush_thread+0x2e/0x40
LR is at flush_thread+0x21/0x40
pc : [<2800954a>] lr : [<2800953d>] psr: 4100000b
sp : 29833d60 ip : 00000000 fp : 00000001
r10: 00003cf8 r9 : 29b1f000 r8 : 00000000
r7 : 29b0bc00 r6 : 29834000 r5 : 29832000 r4 : 29832000
r3 : ffff0ff0 r2 : 29832000 r1 : 00000000 r0 : 282121f0
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-rc6-00313-gd2205fa30aa7 #191
[<2800afa5>] (unwind_backtrace) from [<2800a327>] (show_stack+0xb/0xc)
[<2800a327>] (show_stack) from [<2800a963>] (__invalid_entry+0x4b/0x4c)
The problem is that set_tls is attempting to clear the TLS location in
the kernel-user helper page, which isn't set up on V7M.
Fix this by guarding the write to the kuser helper page with
a CONFIG_KUSER_HELPERS ifdef.
Fixes: fbfb872f5f ARM: 8148/1: flush TLS and thumbee register state during exec
Reported-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ca918e5e3 upstream.
The alignment fixup incorrectly decodes faulting ARM VLDn/VSTn
instructions (where the optional alignment hint is given but incorrect)
as LDR/STR, leading to register corruption. Detect these and correctly
treat them as unhandled, so that userspace gets the fault it expects.
Reported-by: Simon Hosie <simon.hosie@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fbfb872f5f upstream.
The TPIDRURO and TPIDRURW registers need to be flushed during exec;
otherwise TLS information is potentially leaked. TPIDRURO in
particular needs careful treatment. Since flush_thread basically
needs the same code used to set the TLS in arm_syscall, pull that into
a common set_tls helper in tls.h and use it in both places.
Similarly, TEEHBR needs to be cleared during exec as well. Clearing
its save slot in thread_info isn't right as there is no guarantee
that a thread switch will occur before the new program runs. Just
setting the register directly is sufficient.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a040803a9d upstream.
Since commit 1dbfa187da ("ARM: irq migration: force migration off CPU
going down") the ARM interrupt migration code on cpu offline calls
irqchip.irq_set_affinity() with the argument force=true. At the point
of this change the argument had no effect because it was not used by
any interrupt chip driver and there was no semantics defined.
This changed with commit 01f8fa4f01 ("genirq: Allow forcing cpu
affinity of interrupts") which made the force argument useful to route
interrupts to not yet online cpus without checking the target cpu
against the cpu online mask. The following commit ffde1de640
("irqchip: gic: Support forced affinity setting") implemented this for
the GIC interrupt controller.
As a consequence the ARM cpu offline irq migration fails if CPU0 is
offlined, because CPU0 is still set in the affinity mask and the
validataion against cpu online mask is skipped to the force argument
being true. The following first_cpu(mask) selection always selects
CPU0 as the target.
Solve the issue by calling irq_set_affinity() with force=false from
the CPU offline irq migration code so the GIC driver validates the
affinity mask against CPU online mask and therefore removes CPU0 from
the possible target candidates.
Tested on TC2 hotpluging CPU0 in and out. Without this patch the system
locks up as the IRQs are not migrated away from CPU0.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e49d519c45 upstream.
GPIO modules are also interrupt sources. However, they require both the
GPIO number and IRQ type to function properly.
By declaring that GPIO uses interrupt-cells=<1>, we essentially do not
allow users of the nodes to use the interrupt property appropritely.
With this change, the following now works:
interrupt-parent = <&gpio6>;
interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
Fixes: 6e58b8f1da ('ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board')
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7f7a29bf0 upstream.
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8586831317 upstream.
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:
- We clear the monitors on every exception return since commit
200b812d00 ("Clear the exclusive monitor when returning from an
exception"), so this is not necessary to ensure the monitors are
cleared before returning from a fault handler.
- Any dummy STREX will target a temporary scratch area in memory, and
may succeed or fail without corrupting useful data. Its status value
will not be used.
- Any other STREX in the kernel must be preceded by an LDREX, which
will initialise the monitors consistently and will not depend on the
earlier state of the monitors.
Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.
This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6edbbf36d upstream.
X-Gene u-boot runs in EL2 mode with MMU enabled hence we might
have stale EL2 tlb enteris when we enable EL2 MMU on each host CPU.
This can happen on any ARM/ARM64 board running bootloader in
Hyp-mode (or EL2-mode) with MMU enabled.
This patch ensures that we flush all Hyp-mode (or EL2-mode) TLBs
on each host CPU before enabling Hyp-mode (or EL2-mode) MMU.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05e0127f9e upstream.
The architecture specifies that when the processor wakes up from a WFE
or WFI instruction, the instruction is considered complete, however we
currrently return to EL1 (or EL0) at the WFI/WFE instruction itself.
While most guests may not be affected by this because their local
exception handler performs an exception returning setting the event bit
or with an interrupt pending, some guests like UEFI will get wedged due
this little mishap.
Simply skip the instruction when we have completed the emulation.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc824534d4 upstream.
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.
My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.
In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.
So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b5f7428f8 upstream.
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc994c77ce upstream.
Commit cb8db5d45 (UAPI: (Scripted) Disintegrate arch/arm/include/asm) moved
these syscall comments out of their context into the UAPI headers. Fix this.
Fixes: cb8db5d457 ("UAPI: (Scripted) Disintegrate arch/arm/include/asm")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44e6ab1b61 upstream.
The mailbox DT node for AM4372 is enabled and is corrected to
remove some properties that have crept in by mistake.
Fixes: 9e3269b (ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes)
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e120fb4596 upstream.
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811a2407a3 upstream.
On LPAE, each level 1 (pgd) page table entry maps 1GiB, and the level 2
(pmd) entries map 2MiB.
When the identity mapping is created on LPAE, the pgd pointers are copied
from the swapper_pg_dir. If we find that we need to modify the contents
of a pmd, we allocate a new empty pmd table and insert it into the
appropriate 1GB slot, before then filling it with the identity mapping.
However, if the 1GB slot covers the kernel lowmem mappings, we obliterate
those mappings.
When replacing a PMD, first copy the old PMD contents to the new PMD, so
that we preserve the existing mappings, particularly the mappings of the
kernel itself.
[rewrote commit message and added code comment -- rmk]
Fixes: ae2de10173 ("ARM: LPAE: Add identity mapping support for the 3-level page table format")
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 823a19cd3b upstream.
If init_mm.brk is not section aligned, the LPAE fixup code will miss
updating the final PMD. Fix this by aligning map_end.
Fixes: a77e0c7b27 ("ARM: mm: Recreate kernel mappings in early_paging_init()")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28c9770bcb upstream.
Fix the address of L2 controler register in hi3620 SoC.
This has been wrong from the point that the file was merged
in v3.14.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3c400ef47 upstream.
Fix the same alignment bug as in arm64 - we need to pass residue
unprocessed bytes as the last argument to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22970070e0 upstream.
Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4badad352a upstream.
The optimistic spin code assumes regular stores and cmpxchg() play nice;
this is found to not be true for at least: parisc, sparc32, tile32,
metag-lock1, arc-!llsc and hexagon.
There is further wreckage, but this in particular seemed easy to
trigger, so blacklist this.
Opt in for known good archs.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: John David Anglin <dave.anglin@bell.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/20140606175316.GV13930@laptop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c021f241f4 upstream.
Fix a parser-bug in the omap2 muxing code where muxtable-entries will be
wrongly selected if the requested muxname is a *prefix* of their
m0-entry and they have a matching mN-entry. Fix by additionally checking
that the length of the m0_entry is equal.
For example muxing of "dss_data2.dss_data2" on omap32xx will fail
because the prefix "dss_data2" will match the mux-entries "dss_data2" as
well as "dss_data20", with the suffix "dss_data2" matching m0 (for
dss_data2) and m4 (for dss_data20). Thus both are recognized as signal
path candidates:
Relevant muxentries from mux34xx.c:
_OMAP3_MUXENTRY(DSS_DATA20, 90,
"dss_data20", NULL, "mcspi3_somi", "dss_data2",
"gpio_90", NULL, NULL, "safe_mode"),
_OMAP3_MUXENTRY(DSS_DATA2, 72,
"dss_data2", NULL, NULL, NULL,
"gpio_72", NULL, NULL, "safe_mode"),
This will result in a failure to mux the pin at all:
_omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2
Patch should apply to linus' latest master down to rather old linux-2.6
trees.
Signed-off-by: David R. Piegdon <lkml@p23q.org>
Cc: stable@vger.kernel.org
[tony@atomide.com: updated description to include full description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6015c1f8a upstream.
This change places MDMA1 in disabled node for Exynos5420.
If MDMA1 region is configured with secure mode, it makes
the boot failure with the following on smdk5420 board.
("Unhandled fault: imprecise external abort (0x1406) at 0x00000000")
Thus, arndale-octa board don't need to do the same thing anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e47043aea3 upstream.
The OpenBlocks AX3-4 has a non-DT bootloader. It also comes with 1GB of
soldered on RAM, and a DIMM slot for expansion.
Unfortunately, atags_to_fdt() doesn't work in big-endian mode, so we see
the following failure when attempting to boot a big-endian kernel:
686 slab pages
17 pages shared
0 pages swap cached
[ pid ] uid tgid total_vm rss nr_ptes swapents oom_score_adj name
Kernel panic - not syncing: Out of memory and no killable processes...
CPU: 1 PID: 351 Comm: kworker/u4:0 Not tainted 3.15.0-rc8-next-20140603 #1
[<c0215a54>] (unwind_backtrace) from [<c021160c>] (show_stack+0x10/0x14)
[<c021160c>] (show_stack) from [<c0802500>] (dump_stack+0x78/0x94)
[<c0802500>] (dump_stack) from [<c0800068>] (panic+0x90/0x21c)
[<c0800068>] (panic) from [<c02b5704>] (out_of_memory+0x320/0x340)
[<c02b5704>] (out_of_memory) from [<c02b93a0>] (__alloc_pages_nodemask+0x874/0x930)
[<c02b93a0>] (__alloc_pages_nodemask) from [<c02d446c>] (handle_mm_fault+0x744/0x96c)
[<c02d446c>] (handle_mm_fault) from [<c02cf250>] (__get_user_pages+0xd0/0x4c0)
[<c02cf250>] (__get_user_pages) from [<c02f3598>] (get_arg_page+0x54/0xbc)
[<c02f3598>] (get_arg_page) from [<c02f3878>] (copy_strings+0x278/0x29c)
[<c02f3878>] (copy_strings) from [<c02f38bc>] (copy_strings_kernel+0x20/0x28)
[<c02f38bc>] (copy_strings_kernel) from [<c02f4f1c>] (do_execve+0x3a8/0x4c8)
[<c02f4f1c>] (do_execve) from [<c025ac10>] (____call_usermodehelper+0x15c/0x194)
[<c025ac10>] (____call_usermodehelper) from [<c020e9b8>] (ret_from_fork+0x14/0x3c)
CPU0: stopping
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.15.0-rc8-next-20140603 #1
[<c0215a54>] (unwind_backtrace) from [<c021160c>] (show_stack+0x10/0x14)
[<c021160c>] (show_stack) from [<c0802500>] (dump_stack+0x78/0x94)
[<c0802500>] (dump_stack) from [<c021429c>] (handle_IPI+0x138/0x174)
[<c021429c>] (handle_IPI) from [<c02087f0>] (armada_370_xp_handle_irq+0xb0/0xcc)
[<c02087f0>] (armada_370_xp_handle_irq) from [<c0212100>] (__irq_svc+0x40/0x50)
Exception stack(0xc0b6bf68 to 0xc0b6bfb0)
bf60: e9fad598 00000000 00f509a3 00000000 c0b6a000 c0b724c4
bf80: c0b72458 c0b6a000 00000000 00000000 c0b66da0 c0b6a000 00000000 c0b6bfb0
bfa0: c027bb94 c027bb24 60000313 ffffffff
[<c0212100>] (__irq_svc) from [<c027bb24>] (cpu_startup_entry+0x54/0x214)
[<c027bb24>] (cpu_startup_entry) from [<c0ac5b30>] (start_kernel+0x318/0x37c)
[<c0ac5b30>] (start_kernel) from [<00208078>] (0x208078)
---[ end Kernel panic - not syncing: Out of memory and no killable processes...
A similar failure will also occur if ARM_ATAG_DTB_COMPAT isn't selected.
Fix this by setting a sane default (1 GB) in the dts file.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86f40622af upstream.
When enable LPAE and big-endian in a hisilicon board, while specify
mem=384M mem=512M@7680M, will get bad page state:
Freeing unused kernel memory: 180K (c0466000 - c0493000)
BUG: Bad page state in process init pfn:fa442
page:c7749840 count:0 mapcount:-1 mapping: (null) index:0x0
page flags: 0x40000400(reserved)
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 3.10.27+ #66
[<c000f5f0>] (unwind_backtrace+0x0/0x11c) from [<c000cbc4>] (show_stack+0x10/0x14)
[<c000cbc4>] (show_stack+0x10/0x14) from [<c009e448>] (bad_page+0xd4/0x104)
[<c009e448>] (bad_page+0xd4/0x104) from [<c009e520>] (free_pages_prepare+0xa8/0x14c)
[<c009e520>] (free_pages_prepare+0xa8/0x14c) from [<c009f8ec>] (free_hot_cold_page+0x18/0xf0)
[<c009f8ec>] (free_hot_cold_page+0x18/0xf0) from [<c00b5444>] (handle_pte_fault+0xcf4/0xdc8)
[<c00b5444>] (handle_pte_fault+0xcf4/0xdc8) from [<c00b6458>] (handle_mm_fault+0xf4/0x120)
[<c00b6458>] (handle_mm_fault+0xf4/0x120) from [<c0013754>] (do_page_fault+0xfc/0x354)
[<c0013754>] (do_page_fault+0xfc/0x354) from [<c0008400>] (do_DataAbort+0x2c/0x90)
[<c0008400>] (do_DataAbort+0x2c/0x90) from [<c0008fb4>] (__dabt_usr+0x34/0x40)
The bad pfn:fa442 is not system memory(mem=384M mem=512M@7680M), after debugging,
I find in page fault handler, will get wrong pfn from pte just after set pte,
as follow:
do_anonymous_page()
{
...
set_pte_at(mm, address, page_table, entry);
//debug code
pfn = pte_pfn(entry);
pr_info("pfn:0x%lx, pte:0x%llxn", pfn, pte_val(entry));
//read out the pte just set
new_pte = pte_offset_map(pmd, address);
new_pfn = pte_pfn(*new_pte);
pr_info("new pfn:0x%lx, new pte:0x%llxn", pfn, pte_val(entry));
...
}
pfn: 0x1fa4f5, pte:0xc00001fa4f575f
new_pfn:0xfa4f5, new_pte:0xc00000fa4f5f5f //new pfn/pte is wrong.
The bug is happened in cpu_v7_set_pte_ext(ptep, pte):
An LPAE PTE is a 64bit quantity, passed to cpu_v7_set_pte_ext in the r2 and r3 registers.
On an LE kernel, r2 contains the LSB of the PTE, and r3 the MSB.
On a BE kernel, the assignment is reversed.
Unfortunately, the current code always assumes the LE case,
leading to corruption of the PTE when clearing/setting bits.
This patch fixes this issue much like it has been done already in the
cpu_v7_switch_mm case.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3683f44c42 upstream.
While debugging the FEC ethernet driver using stacktrace, it was noticed
that the stacktraces always begin as follows:
[<c00117b4>] save_stack_trace_tsk+0x0/0x98
[<c0011870>] save_stack_trace+0x24/0x28
...
This is because the stack trace code includes the stack frames for itself.
This is incorrect behaviour, and also leads to "skip" doing the wrong
thing (which is the number of stack frames to avoid recording.)
Perversely, it does the right thing when passed a non-current thread. Fix
this by ensuring that we have a known constant number of frames above the
main stack trace function, and always skip these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c177c81e09 upstream.
Currently hugepage migration is available for all archs which support
pmd-level hugepage, but testing is done only for x86_64 and there're
bugs for other archs. So to avoid breaking such archs, this patch
limits the availability strictly to x86_64 until developers of other
archs get interested in enabling this feature.
Simply disabling hugepage migration on non-x86_64 archs is not enough to
fix the reported problem where sys_move_pages() hits the BUG_ON() in
follow_page(FOLL_GET), so let's fix this by checking if hugepage
migration is supported in vma_migratable().
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77c2f02edb upstream.
Commit 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
apparently required that checks for CONFIG_USB_GADGET_OMAP would be
replaced with checks for CONFIG_USB_OMAP. Do so now for the remaining
checks for CONFIG_USB_GADGET_OMAP, even though these checks have
basically been broken since v3.1.
And, since we're touching this code, use the IS_ENABLED() macro, so
things will now (hopefully) also work if USB_OMAP is modular.
Fixes: 193ab2a607 ("usb: gadget: allow multiple gadgets to be built")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dcc87fec8 upstream.
sam9x5 SoCs have the following errata:
"RTC: Interrupt Mask Register cannot be used
Interrupt Mask Register read always returns 0."
Hence we should not rely on what IMR claims about already masked IRQs
and just disable all IRQs.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Reviewed-by: Johan Hovold <johan@hovold.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Roszko <mark.roszko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 483a6c9d44 upstream.
According to the ARM ARM, the behaviour is UNPREDICTABLE if the PC read
from the exception return stack is not half word aligned. See the
pseudo code for ExceptionReturn() and PopStack().
The signal handler's address has the bit 0 set, and setup_return()
directly writes this to regs->ARM_pc. Current hardware happens to
discard this bit, but QEMU's emulation doesn't and this makes processes
crash. Mask out bit 0 before the exception return in order to get
predictable behaviour.
Fixes: 19c4d593f0 ("ARM: ARMv7-M: Add support for exception handling")
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 537094b64b upstream.
According to arm procedure call standart r2 register is call-cloberred.
So after the result of x expression was put into r2 any following
function call in p may overwrite r2. To fix this, the result of p
expression must be saved to the temporary variable before the
assigment x expression to __r2.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b353a706a upstream.
On OMAP4 panda board, there have been several bug reports about boot
hang and lock-ups with CPU_IDLE enabled. The root cause of the issue
is missing interrupts while in idle state. Commit cb7094e8 {cpuidle / omap4 :
use CPUIDLE_FLAG_TIMER_STOP flag} moved the broadcast notifiers to common
code for right reasons but on OMAP4 which suffers from a nasty ROM code
bug with GIC, commit ff999b8a {ARM: OMAP4460: Workaround for ROM bug ..},
we loose interrupts which leads to issues like lock-up, hangs etc.
Patch reverts commit cb7094 {cpuidle / omap4 : use CPUIDLE_FLAG_TIMER_STOP
flag} and 54769d6 {cpuidle: OMAP4: remove timer broadcast initialization} to
avoid the issue. With this change, OMAP4 panda boards, the mentioned
issues are getting fixed. We no longer loose interrupts which was the cause
of the regression.
Fixes: cb7094e8 (cpuidle / omap4 : use CPUIDLE_FLAG_TIMER_STOP flag)
Fixes: ff999b8a (cpuidle: OMAP4: remove timer broadcast initialization)
Cc: Roger Quadros <rogerq@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Reported-tested-by: Roger Quadros <rogerq@ti.com>
Reported-tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d7e1aee6 upstream.
Commit 7b2e127759 ("ARM: OMAP3: clock:
Back-propagate rate change from cam_mclk to dpll4_m5") enabled clock
rate back-propagation from cam_mclk do dpll4_m5 on OMAP3630 only.
Perform back-propagation on other OMAP3 platforms as well.
Reported-by: Jean-Philippe François <jp.francois@cynove.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5005e0b767 upstream.
Commit c66d039197 broke NAND for non-DT boot on all OMAP2 and OMAP3
boards using board_nand_init(). Following error is seen at boot
[ 0.154998] (null): Unsupported NAND ECC scheme selected
For OMAP2 and OMAP3 platforms, the ecc_opt parameter in platform data
must be set to OMAP_ECC_HAM1_CODE_HW to work properly.
Tested on omap3-beagle c4.
Fixes: c66d039197 (mtd: nand: omap: combine different flavours of 1-bit hamming ecc schemes)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f9e19ad88 upstream.
McPDM need to be configured to NO_IDLE mode when it is in used otherwise
vital clocks will be gated which results 'slow motion' audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1d70e5dc2 upstream.
If we fail to allocate struct platform_device pdev we
dereference it after the goto label err.
This bug was found using coccinelle.
Fixes: afa77ef (ARM: mx3: dynamically allocate "ipu-core" devices)
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b25bcf1bca upstream.
Since the mvebu-soc-id code in mach-mvebu/ was introduced, several
users have noticed a regression: the PCIe card connected in the first
PCIe interface is not detected properly.
This is due to the fact that the mvebu-soc-id code enables the PCIe
clock of the first PCIe interface, reads the SoC device ID and
revision number (yes this information is made available as part of
PCIe registers), and then disables the clock. However, by doing this,
we gate the clock and therefore loose the complex PCIe configuration
that was done by the bootloader.
Unfortunately, as of today, the kernel is not capable of doing this
complex configuration by itself, so we really need to keep the PCIe
clock enabled. However, we don't want to keep it enabled
unconditionally: if the PCIe interface is not enabled or PCI support
is not compiled into the kernel, there is no reason to keep the PCIe
clock running.
This issue was discussed with Kevin Hilman, and the suggested solution
was to make the mvebu-soc-id code keep the clock enabled in case it
will be needed for PCIe. This is therefore the solution implemented in
this patch.
Long term, we hope to make the kernel more capable in terms of PCIe
configuration for this platform, which will anyway be needed to
support the compilation of the PCIe host controller driver as a
module. In the mean time however, we don't have much other choice than
to implement the currently proposed solution.
Reported-by: Neil Greatorex <neil@fatboyfat.co.uk>
Cc: Neil Greatorex <neil@fatboyfat.co.uk>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1399903900-29977-3-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: af8d1c63af ("ARM: mvebu: Add support to get the ID and the revision of a SoC")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42a18d1cf4 upstream.
The mvebu-soc-id code in mach-mvebu/ needs to enable a clock to read
the SoC device ID and revision number. To do so, it does a clk_get(),
then a clk_prepare_enable(), reads the value, and disables the clock
with clk_disable_unprepare(). However, it forgets to clk_put() the
clock. This commit fixes this issue.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1399903900-29977-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: af8d1c63af ("ARM: mvebu: Add support to get the ID and the revision of a SoC")
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fad87bca7 upstream.
When we configure CONFIG_ARM_LPAE=y, pfn << PAGE_SHIFT will
overflow if pfn >= 0x100000 in copy_oldmem_page.
So use __pfn_to_phys for converting.
Signed-off-by: Liu Hua <sdu.liu@huawei.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfaed5abad upstream.
The current .dts for ste-ccu8540 lacks a 'device_type = "memory"' for
its memory node, relying on an old ppc quirk in order to discover its
memory. Fix the data so that all parsing code can handle it correctly.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e20bae8a3 upstream.
The mvebu-devbus driver had a serious bug, which lead to a 8 bits bus
width declared in the Device Tree being considered as a 16 bits bus
width when configuring the hardware.
This bug in mvebu-devbus driver was compensated by a symetric mistake
in the Armada XP OpenBlocks AX3 Device Tree: a 8 bits bus width was
declared, even though the hardware actually has a 16 bits bus width
connection with the NOR flash.
Now that we have fixed the mvebu-devbus driver to behave according to
its Device Tree binding, this commit fixes the problematic Device Tree
files as well.
This bug was introduced in commit
a7d4f81821 ('ARM: mvebu: Add support for
NOR flash device on Openblocks AX3 board') which was merged in v3.10.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397489361-5833-5-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: a7d4f81821 ('ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board')
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f3aec8f3f0 upstream.
The mvebu-devbus driver had a serious bug, which lead to a 8 bits bus
width declared in the Device Tree being considered as a 16 bits bus
width when configuring the hardware.
This bug in mvebu-devbus driver was compensated by a symetric mistake
in the Armada XP DB Device Tree: a 8 bits bus width was declared, even
though the hardware actually has a 16 bits bus width connection with
the NOR flash.
Now that we have fixed the mvebu-devbus driver to behave according to
its Device Tree binding, this commit fixes the problematic Device Tree
files as well.
This bug was introduced in commit
b484ff42df ('ARM: mvebu: Add support for
NOR flash device on Armada XP-DB board') which was merged in v3.11.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397489361-5833-4-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: b484ff42df ('ARM: mvebu: Add support for NOR flash device on Armada XP-DB board')
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a88f809cc upstream.
The mvebu-devbus driver had a serious bug, which lead to a 8 bits bus
width declared in the Device Tree being considered as a 16 bits bus
width when configuring the hardware.
This bug in mvebu-devbus driver was compensated by a symetric mistake
in the Armada XP GP Device Tree: a 8 bits bus width was declared, even
though the hardware actually has a 16 bits bus width connection with
the NOR flash.
Now that we have fixed the mvebu-devbus driver to behave according to
its Device Tree binding, this commit fixes the problematic Device Tree
files as well.
This bug was introduced in commit
da8d1b3835 ('ARM: mvebu: Add support for
NOR flash device on Armada XP-GP board') which was merged in v3.10.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1397489361-5833-3-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: da8d1b3835 ('ARM: mvebu: Add support for NOR flash device on Armada XP-GP board')
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf7eb97911 upstream.
This is another great example of trainwreck engineering:
commit 2646a0e529 (ARM: edma: Add EDMA crossbar event mux support)
added support for using EDMA on peripherals which have no direct EDMA
event mapping.
The code compiles and does not explode in your face, but that's it.
1) Reading an u16 array from an u32 device tree array simply does not
work. Even if the function is named "edma_of_read_u32_to_s16_array".
It merily calls of_property_read_u16_array. So the resulting 16bit
array will have every other entry = 0.
2) The DT entry for the xbar registers related to xbar has length 0x10
instead of the real length: 0xfd0 - 0xf90 = 0x40.
Not a real problem as it does not cross a page boundary, but
wrong nevertheless.
3) But none of this matters as the mapping never happens:
After reading nonsense edma_of_read_u32_to_s16_array() invalidates
the first array entry pair, so nobody can ever notice the
braindamage by immediate explosion.
Seems the QA criteria for this code was solely not to explode when
someone adds edma-xbar-event-map entries to the DT. Goal achieved,
congratulations!
Not really helpful if someone wants to use edma on a device which
requires a xbar mapping.
Fix the issues by:
- annotating the device tree entry with "/bits/ 16" as documented in
the of_property_read_u16_array kernel doc
- make the size of the xbar register mapping correct
- invalidating the end of the array and not the start
This convoluted mess wants to be completely rewritten as there is no
point to keep the xbar_chan array memory and the iomapping of the xbar
regs around forever. Marking the xbar mapped channels as used should
be done right there.
But that's a different issue and this patch is small enough to make it
work and allows a simple backport for stable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 788296b2d1 upstream.
Commit 54397d8534
("ARM: kirkwood: Relocate PCIe device tree nodes")
moved the pcie-controller nodes for the Kirkwood SoCs to the mbus
bus node. For some reason, two boards were not properly converted
and have their pci-controller nodes still in the ocp bus node.
As the corresponding SoC pcie-controller does not exist anymore,
it is likely that pcie is broken on those boards since above commit.
Fix it by moving the pcie related nodes to the correct location.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Fixes: 54397d8534 ("ARM: kirkwood: Relocate PCIe device tree nodes")
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-2-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cc9d48145 upstream.
In commit 4ca2c04085 ('ARM: orion5x:
Move to ID based window creation'), the mach-orion5x code was changed
to use the new mvebu-mbus API. However, in the process, a mistake was
made on the crypto SRAM window target ID: it should have been 0x9
(verified in the datasheet) and not 0x0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1397400006-4315-2-git-send-email-thomas.petazzoni@free-electrons.com
Fixes: 4ca2c04085 ('ARM: orion5x: Move to ID based window creation')
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d4e08c45a upstream.
The kvm/mmu code shared by arm and arm64 uses kalloc() to allocate
a bounce page (if hypervisor init code crosses page boundary) and
hypervisor PGDs. The problem is that kalloc() does not guarantee
the proper alignment. In the case of the bounce page, the page sized
buffer allocated may also cross a page boundary negating the purpose
and leading to a hang during kvm initialization. Likewise the PGDs
allocated may not meet the minimum alignment requirements of the
underlying MMU. This patch uses __get_free_page() to guarantee the
worst case alignment needs of the bounce page and PGDs on both arm
and arm64.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2f8d6b303 upstream.
In "ARM: dts: am33xx: correcting dt node unit address for usb", the
usb_ctrl_mod and cppi41dma nodes were updated with the correct register
addresses. However, the dts files that reference these nodes were not
updated, and those devices are no longer being enabled.
This patch corrects the references for the affected dts files.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
