commit c1118b3602 upstream.
On x86_64, kernel text mappings are mapped read-only with CONFIG_DEBUG_RODATA.
In that case, KVM will fail to patch VMCALL instructions to VMMCALL
as required on AMD processors.
The failure mode is currently a divide-by-zero exception, which obviously
is a KVM bug that has to be fixed. However, picking the right instruction
between VMCALL and VMMCALL will be faster and will help if you cannot upgrade
the hypervisor.
Reported-by: Chris Webb <chris@arachsys.com>
Tested-by: Chris Webb <chris@arachsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 360743814c upstream.
Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f4aa45cee upstream.
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 995ab5189d upstream.
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f ("arm: mm: Add support for PJ4B cpu and init routines")
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef59a20ba3 upstream.
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b8a3c0109 upstream.
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [c0000003f39ffb10]
pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp: c0000003f39ffc70
msr: 8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40]
pc: 000000000eca7cc4
lr: 000000000eca7c44
sp: fafb4b0
msr: 8000000000001000
dar: 10000000
dsisr: 42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415072a041 upstream.
Instead of the arch specific quirk which we are deprecating
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a2b59d399 ]
We are reading the memory location, so we have to have a memory
constraint in there purely for the sake of showing the data flow
to the compiler.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 82975bc6a6 upstream.
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b61e3621 upstream.
When building with the Gold linker, the .bss and .brk areas of vmlinux
are shown as consecutive instead of having the same file offset. Allow
for either state, as long as things add up correctly.
Fixes: e6023367d7 ("x86, kaslr: Prevent .bss from overlaping initrd")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Link: http://lkml.kernel.org/r/20141118001604.GA25045@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45e2a9d470 upstream.
When setting up permissions on kernel memory at boot, the end of the
PMD that was split from bss remained executable. It should be NX like
the rest. This performs a PMD alignment instead of a PAGE alignment to
get the correct span of memory.
Before:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82c00000 10M RW PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82df5000 2004K RW GLB NX pte
0xffffffff82df5000-0xffffffff82e00000 44K RW GLB x pte
0xffffffff82e00000-0xffffffffc0000000 978M pmd
After:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82e00000 12M RW PSE GLB NX pmd
0xffffffff82e00000-0xffffffffc0000000 978M pmd
[ tglx: Changed it to roundup(_brk_end, PMD_SIZE) and added a comment.
We really should unmap the reminder along with the holes
caused by init,initdata etc. but thats a different issue ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20141114194737.GA3091@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cd3949f70 upstream.
We have some very similarly named command-line options:
arch/x86/kernel/cpu/common.c:__setup("noxsave", x86_xsave_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaveopt", x86_xsaveopt_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaves", x86_xsaves_setup);
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b645af2d59 upstream.
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f442be2fb upstream.
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af726f21ed upstream.
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aaf
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26927f7649 upstream.
If SERIAL_8250 is compiled as a module, the platform specific setup
for Loongson will be a module too, and it will not work very well.
At least on Loongson 3 it will trigger a build failure,
since loongson_sysconf is not exported to modules.
Fix by making the platform specific serial code always built-in.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/8533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbaf113a48 upstream.
Fix incorrect cast that always results in wrong address for the new
frame on 64-bit kernels.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b13b1d2d86 upstream.
We use the accessed bit to age a page at page reclaim time,
and currently we also flush the TLB when doing so.
But in some workloads TLB flush overhead is very heavy. In my
simple multithreaded app with a lot of swap to several pcie
SSDs, removing the tlb flush gives about 20% ~ 30% swapout
speedup.
Fortunately just removing the TLB flush is a valid optimization:
on x86 CPUs, clearing the accessed bit without a TLB flush
doesn't cause data corruption.
It could cause incorrect page aging and the (mistaken) reclaim of
hot pages, but the chance of that should be relatively low.
So as a performance optimization don't flush the TLB when
clearing the accessed bit, it will eventually be flushed by
a context switch or a VM operation anyway. [ In the rare
event of it not getting flushed for a long time the delay
shouldn't really matter because there's no real memory
pressure for swapout to react to. ]
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: linux-mm@kvack.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20140408075809.GA1764@kernel.org
[ Rewrote the changelog and the code comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2b9e6c1a3 upstream.
Commit fc3a9157d3 ("KVM: X86: Don't report L2 emulation failures to
user-space") disabled the reporting of L2 (nested guest) emulation failures to
userspace due to race-condition between a vmexit and the instruction emulator.
The same rational applies also to userspace applications that are permitted by
the guest OS to access MMIO area or perform PIO.
This patch extends the current behavior - of injecting a #UD instead of
reporting it to userspace - also for guest userspace code.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1996388e9f upstream.
This was discussed back in February:
https://lkml.org/lkml/2014/2/18/956
But I never saw a patch come out of it.
On IvyBridge we share the SandyBridge cache event tables, but the
dTLB-load-miss event is not compatible. Patch it up after
the fact to the proper DTLB_LOAD_MISSES.DEMAND_LD_MISS_CAUSES_A_WALK
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1407141528200.17214@vincent-weaver-1.umelst.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Hou Pengyang <houpengyang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 888be25402 upstream.
If we are running BE8, the data and instruction endianness do not
match, so use <asm/opcodes.h> to correctly translate memory accesses
into ARM instructions.
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[taras.kondratiuk@linaro.org: fixed Thumb instruction fetch order]
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
[wangnan: backport to 3.10 and 3.14:
- adjust context
- backport all changes on arch/arm/kernel/probes.c to
arch/arm/kernel/kprobes-common.c since we don't have
commit c18377c303.
- After the above adjustments, becomes same to Taras Kondratiuk's
original patch:
http://lists.linaro.org/pipermail/linaro-kernel/2014-January/010346.html
]
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6023367d7 upstream.
When choosing a random address, the current implementation does not take into
account the reversed space for .bss and .brk sections. Thus the relocated kernel
may overlap other components in memory. Here is an example of the overlap from a
x86_64 kernel in qemu (the ranges of physical addresses are presented):
Physical Address
0x0fe00000 --+--------------------+ <-- randomized base
/ | relocated kernel |
vmlinux.bin | (from vmlinux.bin) |
0x1336d000 (an ELF file) +--------------------+--
\ | | \
0x1376d870 --+--------------------+ |
| relocs table | |
0x13c1c2a8 +--------------------+ .bss and .brk
| | |
0x13ce6000 +--------------------+ |
| | /
0x13f77000 | initrd |--
| |
0x13fef374 +--------------------+
The initrd image will then be overwritten by the memset during early
initialization:
[ 1.655204] Unpacking initramfs...
[ 1.662831] Initramfs unpacking failed: junk in compressed archive
This patch prevents the above situation by requiring a larger space when looking
for a random kernel base, so that existing logic can effectively avoids the
overlap.
[kees: switched to perl to avoid hex translation pain in mawk vs gawk]
[kees: calculated overlap without relocs table]
Fixes: 82fa9637a2 ("x86, kaslr: Select random position from e820 maps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Junjie Mao <eternal.n08@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1414762838-13067-1-git-send-email-eternal.n08@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0a717f23d upstream.
Save the patch while we're running on the BSP instead of later, before
the initrd has been jettisoned. More importantly, on 32-bit we need to
access the physical address instead of the virtual.
This way we actually do find it on the APs instead of having to go
through the initrd each time.
Tested-by: Richard Hendershot <rshendershot@mchsi.com>
Fixes: 5335ba5cf4 ("x86, microcode, AMD: Fix early ucode loading")
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4750a0d112 upstream.
Konrad triggered the following splat below in a 32-bit guest on an AMD
box. As it turns out, in save_microcode_in_initrd_amd() we're using the
*physical* address of the container *after* we have enabled paging and
thus we #PF in load_microcode_amd() when trying to access the microcode
container in the ramdisk range.
Because the ramdisk is exactly there:
[ 0.000000] RAMDISK: [mem 0x35e04000-0x36ef9fff]
and we fault at 0x35e04304.
And since this guest doesn't relocate the ramdisk, we don't do the
computation which will give us the correct virtual address and we end up
with the PA.
So, we should actually be using virtual addresses on 32-bit too by the
time we're freeing the initrd. Do that then!
Unpacking initramfs...
BUG: unable to handle kernel paging request at 35d4e304
IP: [<c042e905>] load_microcode_amd+0x25/0x4a0
*pde = 00000000
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.17.1-302.fc21.i686 #1
Hardware name: Xen HVM domU, BIOS 4.4.1 10/01/2014
task: f5098000 ti: f50d0000 task.ti: f50d0000
EIP: 0060:[<c042e905>] EFLAGS: 00010246 CPU: 0
EIP is at load_microcode_amd+0x25/0x4a0
EAX: 00000000 EBX: f6e9ec4c ECX: 00001ec4 EDX: 00000000
ESI: f5d4e000 EDI: 35d4e2fc EBP: f50d1ed0 ESP: f50d1e94
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 35d4e304 CR3: 00e33000 CR4: 000406d0
Stack:
00000000 00000000 f50d1ebc f50d1ec4 f5d4e000 c0d7735a f50d1ed0 15a3d17f
f50d1ec4 00600f20 00001ec4 bfb83203 f6e9ec4c f5d4e000 c0d7735a f50d1ed8
c0d80861 f50d1ee0 c0d80429 f50d1ef0 c0d889a9 f5d4e000 c0000000 f50d1f04
Call Trace:
? unpack_to_rootfs
? unpack_to_rootfs
save_microcode_in_initrd_amd
save_microcode_in_initrd
free_initrd_mem
populate_rootfs
? unpack_to_rootfs
do_one_initcall
? unpack_to_rootfs
? repair_env_string
? proc_mkdir
kernel_init_freeable
kernel_init
ret_from_kernel_thread
? rest_init
Reported-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=1158204
Fixes: 75a1ba5b2c ("x86, microcode, AMD: Unify valid container checks")
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/20141101100100.GA4462@pd.tnic
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2fe749f50b upstream.
Switch over the msgctl, shmat, shmctl and semtimedop syscalls to use the compat
layer. The problem was found with the debian procenv package, which called
shmctl(0, SHM_INFO, &info);
in which the shmctl syscall then overwrote parts of the surrounding areas on
the stack on which the info variable was stored and thus lead to a segfault
later on.
Additionally fix the definition of struct shminfo64 to use unsigned longs like
the other architectures. This has no impact on userspace since we only have a
32bit userspace up to now.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 899d5933b2 upstream.
When experimenting with patches to provide kprobes support for aarch64
smp machines would hang when inserting breakpoints into kernel code.
The hangs were caused by a race condition in the code called by
aarch64_insn_patch_text_sync(). The first processor in the
aarch64_insn_patch_text_cb() function would patch the code while other
processors were still entering the function and incrementing the
cpu_count field. This resulted in some processors never observing the
exit condition and exiting the function. Thus, processors in the
system hung.
The first processor to enter the patching function performs the
patching and signals that the patching is complete with an increment
of the cpu_count field. When all the processors have incremented the
cpu_count field the cpu_count will be num_cpus_online()+1 and they
will return to normal execution.
Fixes: ae16480785 arm64: introduce interfaces to hotpatch kernel and module code
Signed-off-by: William Cohen <wcohen@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97fc15436b upstream.
ARM64 currently doesn't fix up faults on the single-byte (strb) case of
__clear_user... which means that we can cause a nasty kernel panic as an
ordinary user with any multiple PAGE_SIZE+1 read from /dev/zero.
i.e.: dd if=/dev/zero of=foo ibs=1 count=1 (or ibs=65537, etc.)
This is a pretty obscure bug in the general case since we'll only
__do_kernel_fault (since there's no extable entry for pc) if the
mmap_sem is contended. However, with CONFIG_DEBUG_VM enabled, we'll
always fault.
if (!down_read_trylock(&mm->mmap_sem)) {
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
retry:
down_read(&mm->mmap_sem);
} else {
/*
* The above down_read_trylock() might have succeeded in
* which
* case, we'll have missed the might_sleep() from
* down_read().
*/
might_sleep();
if (!user_mode(regs) && !search_exception_tables(regs->pc))
goto no_context;
}
Fix that by adding an extable entry for the strb instruction, since it
touches user memory, similar to the other stores in __clear_user.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Reported-by: Miloš Prchlík <mprchlik@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 238962ac71 upstream.
To speed up decompression, the decompressor sets up a flat, cacheable
mapping of memory. However, when there is insufficient space to hold
the page tables for this mapping, we don't bother to enable the caches
and subsequently skip all the cache maintenance hooks.
Skipping the cache maintenance before jumping to the relocated code
allows the processor to predict the branch and populate the I-cache
with stale data before the relocation loop has completed (since a
bootloader may have SCTLR.I set, which permits normal, cacheable
instruction fetches regardless of SCTLR.M).
This patch moves the cache maintenance check into the maintenance
routines themselves, allowing the v6/v7 versions to invalidate the
I-cache regardless of the MMU state.
Reported-by: Marc Carino <marc.ceeeee@gmail.com>
Tested-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08b964ff3c upstream.
The kuser helpers page is not set up on non-MMU systems, so it does
not make sense to allow CONFIG_KUSER_HELPERS to be enabled when
CONFIG_MMU=n. Allowing it to be set on !MMU results in an oops in
set_tls (used in execve and the arm_syscall trap handler):
Unhandled exception: IPSR = 00000005 LR = fffffff1
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
task: 8b838000 ti: 8b82a000 task.ti: 8b82a000
PC is at flush_thread+0x32/0x40
LR is at flush_thread+0x21/0x40
pc : [<8f00157a>] lr : [<8f001569>] psr: 4100000b
sp : 8b82be20 ip : 00000000 fp : 8b83c000
r10: 00000001 r9 : 88018c84 r8 : 8bb85000
r7 : 8b838000 r6 : 00000000 r5 : 8bb77400 r4 : 8b82a000
r3 : ffff0ff0 r2 : 8b82a000 r1 : 00000000 r0 : 88020354
xPSR: 4100000b
CPU: 0 PID: 1 Comm: swapper Not tainted 3.18.0-rc1-00041-ga30465a #216
[<8f002bc1>] (unwind_backtrace) from [<8f002033>] (show_stack+0xb/0xc)
[<8f002033>] (show_stack) from [<8f00265b>] (__invalid_entry+0x4b/0x4c)
As best I can tell this issue existed for the set_tls ARM syscall
before commit fbfb872f5f "ARM: 8148/1: flush TLS and thumbee
register state during exec" consolidated the TLS manipulation code
into the set_tls helper function, but now that we're using it to flush
register state during execve, !MMU users encounter the oops at the
first exec.
Prevent CONFIG_MMU=n configurations from enabling
CONFIG_KUSER_HELPERS.
Fixes: fbfb872f5f (ARM: 8148/1: flush TLS and thumbee register state during exec)
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Reported-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2651cc6974 upstream.
Userspace actually passes single parameter (path name) to the umount
syscall, so new umount just fails. Fix it by requesting old umount
syscall implementation and re-wiring umount to it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81f49a8fd7 upstream.
is_compat_task() is the wrong check for audit arch; the check should
be is_ia32_task(): x32 syscalls should be AUDIT_ARCH_X86_64, not
AUDIT_ARCH_I386.
CONFIG_AUDITSYSCALL is currently incompatible with x32, so this has
no visible effect.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/a0138ed8c709882aec06e4acc30bfa9b623b8717.1409954077.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a17fdc4f4 ]
Atomicity between xchg and cmpxchg cannot be guaranteed when xchg is
implemented with a swap and cmpxchg is implemented with locks.
Without this, e.g. mcs_spin_lock and mcs_spin_unlock are broken.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0aedcd4f1 ]
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9bce21828d ]
Interpret the media type from v1.1 protocol to support CDROM/DVD.
For v1.0 protocol, a disk's size continues to be calculated from the
geometry returned by the vdisk server. The geometry returned by the server
can be less than the actual number of sectors available in the backing
image/device due to the rounding in the division used to compute the
geometry in the vdisk server.
In v1.1 protocol a disk's actual size in sectors is returned during the
handshake. Use this size when v1.1 protocol is negotiated. Since this size
will always be larger than the former geometry computed size, disks created
under v1.0 will be forwards compatible to v1.1, but not vice versa.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10ccaf178b upstream.
In powerpc pseries platform dlpar operations, use device_online() and
device_offline() instead of cpu_up() and cpu_down().
Calling cpu_up/down() directly does not update the cpu device offline
field, which is used to online/offline a cpu from sysfs. Calling
device_online/offline() instead keeps the sysfs cpu online value
correct. The hotplug lock, which is required to be held when calling
device_online/offline(), is already held when dlpar_online/offline_cpu()
are called, since they are called only from cpu_probe|release_store().
This patch fixes errors on phyp (PowerVM) systems that have cpu(s)
added/removed using dlpar operations; without this patch, the
/sys/devices/system/cpu/cpuN/online nodes do not correctly show the
online state of added/removed cpus.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Fixes: 0902a9044f ("Driver core: Use generic offline/online for CPU offline/online")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b47dcbdc51 upstream.
If the TSC is unusable or disabled, then this patch fixes:
- Confusion while trying to clear old APIC interrupts.
- Division by zero and incorrect programming of the TSC deadline
timer.
This fixes boot if the CPU has a TSC deadline timer but a missing or
broken TSC. The failure to boot can be observed with qemu using
-cpu qemu64,-tsc,+tsc-deadline
This also happens to me in nested KVM for unknown reasons.
With this patch, I can boot cleanly (although without a TSC).
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Bandan Das <bsd@redhat.com>
Link: http://lkml.kernel.org/r/e2fa274e498c33988efac0ba8b7e3120f7f92d78.1413393027.git.luto@amacapital.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 849f5d8943 upstream.
Add Braswell PCI ID to list of supported ID's for the IOSF driver.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1411017231-20807-2-git-send-email-david.e.box@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aece118e48 upstream.
Intel processors which don't report cache information via cpuid(2)
or cpuid(4) need quirk code in the legacy_cache_size callback to
report this data. For Intel that callback is is intel_size_cache().
This patch enables calling of cpu_detect_cache_sizes() inside of
init_intel() and hence the calling of the legacy_cache callback in
intel_size_cache(). Adding this call will ensure that PIII Tualatin
currently in intel_size_cache() and Quark SoC X1000 being added to
intel_size_cache() in this patch will report their respective cache
sizes.
This model of calling cpu_detect_cache_sizes() is consistent with
AMD/Via/Cirix/Transmeta and Centaur.
Also added is a string to idenitfy the Quark as Quark SoC X1000
giving better and more descriptive output via /proc/cpuinfo
Adding cpu_detect_cache_sizes to init_intel() will enable calling
of intel_size_cache() on Intel processors which currently no code
can reach. Therefore this patch will also re-enable reporting
of PIII Tualatin cache size information as well as add
Quark SoC X1000 support.
Comment text and cache flow logic suggested by Thomas Gleixner
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: davej@redhat.com
Cc: hmh@hmh.eng.br
Link: http://lkml.kernel.org/r/1412641189-12415-3-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04725ad594 upstream.
Introduce PCI IDs macro for the list of supported product:
BayTrail & Quark X1000.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-5-git-send-email-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90916e048c upstream.
Add PCI device ID, i.e. that of the Host Bridge,
for IOSF MBI driver.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-4-git-send-email-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ef1def800 upstream.
Added all the MBI units below and their associated read/write
opcodes:
- Host Bridge Arbiter
- Host Bridge
- Remote Management Unit
- Memory Manager & eSRAM
- SoC Unit
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-3-git-send-email-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b8f0c8780 upstream.
Currently drivers that run on non-IOSF systems (Core/Xeon) can't use the IOSF
driver on SOC's without selecting it which forces an unnecessary and limiting
dependency. Provides dummy functions to allow these modules to conditionally
use the driver on IOSF equipped platforms without impacting their ability to
compile and load on non-IOSF platforms. Build default m to ensure availability
on x86 SOC's.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-2-git-send-email-david.e.box@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9e0f162a36 upstream.
In commit 8393c524a2 (MIPS: tlbex: Fix a missing statement for
HUGETLB), the TLB Refill handler was fixed so that non-OCTEON targets
would work properly with huge pages. The change was incorrect in that
it broke the OCTEON case.
The problem is shown here:
xxx0: df7a0000 ld k0,0(k1)
.
.
.
xxxc0: df610000 ld at,0(k1)
xxxc4: 335a0ff0 andi k0,k0,0xff0
xxxc8: e825ffcd bbit1 at,0x5,0x0
xxxcc: 003ad82d daddu k1,at,k0
.
.
.
In the non-octeon case there is a destructive test for the huge PTE
bit, and then at 0, $k0 is reloaded (that is what the 8393c524a2
patch added).
In the octeon case, we modify k1 in the branch delay slot, but we
never need k0 again, so the new load is not needed, but since k1 is
modified, if we do the load, we load from a garbage location and then
get a nested TLB Refill, which is seen in userspace as either SIGBUS
or SIGSEGV (depending on the garbage).
The real fix is to only do this reloading if it is needed, and never
where it is harmful.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aedd153f5b upstream.
Code before the .fixup section needs to have the .insn directive.
This has no side effects on MIPS32/64 but it affects the way microMIPS
loads the address for the return label.
Fixes the following build problem:
mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x4a0: Unsupported jump between
ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Makefile:819: recipe for target 'vmlinux' failed
The fix is similar to 1658f914ff ("MIPS: microMIPS:
Disable LL/SC and fix linker bug.")
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8117/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3441edd2d upstream.
-Pass the expected arg to non-boot park'ing routine
(It worked so far because existing SMP backends don't use the arg)
-CONFIG_DEBUG_PREEMPT warning
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
