commit c8648508eb upstream.
On success, callback function returns 0. So invert the if condition
check so that we can break out of loop.
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87f966d97b upstream.
On a MIPS Malta board, tons of fifo underflow errors have been observed
when using u-boot as bootloader instead of YAMON. The reason for that
is that YAMON used to set the pcnet device to SRAM mode but u-boot does
not. As a result, the default Tx threshold (64 bytes) is now too small to
keep the fifo relatively used and it can result to Tx fifo underflow errors.
As a result of which, it's best to setup the SRAM on supported controllers
so we can always use the NOUFLO bit.
Cc: <netdev@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Cc: Don Fry <pcnet32@frontier.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 391949b6f0 upstream.
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5db29806b upstream.
Since it's possible for the discard and write same queue limits to
change while the upper level command is being sliced and diced, fix up
both of them (a) to reject IO if the special command is unsupported at
the start of the function and (b) read the limits once and let the
commands error out on their own if the status happens to change.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab7c7bb6f4 upstream.
__dm_destroy() must take the suspend_lock so that its presuspend and
postsuspend calls do not race with an internal suspend.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a104a45ba7 upstream.
The commit 9cade1a46c (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com>
Fixes: 9cade1a46c (dma: dw: split driver to library part and platform code)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c8790bcb upstream.
When the driver sets this rate a power of zero value is set causing
data flow stoppage until another rate is tried.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 163fe301b9 upstream.
When the driver sets this rate a power of zero value is set causing
data flow stoppage until another rate is tried.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7c146053d upstream.
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f1bce487c upstream.
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5ac97a1b97
It was incorrectly applied, as it merged with fuzz.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
commit 75c3d0bf9c upstream.
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d556546e7e upstream.
This patch adds a missing set of conditional check braces in
ft_invl_hw_context() originally introduced by commit dcd998ccd
when handling DDP failures in ft_recv_write_data() code.
commit dcd998ccdb
Author: Kiran Patil <kiran.patil@intel.com>
Date: Wed Aug 3 09:20:01 2011 +0000
tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b8f10da3b upstream.
The initialisation of the efm32 clocksource first sets up the irq and only
after that initialises the data needed for irq handling. In case this
initialisation is delayed the irq handler would dereference a NULL pointer.
I'm not aware of anything that could delay the process in such a way, but it's
better to be safe than sorry, so setup the irq only when the clock event device
is ready.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 328f494d95 upstream.
When inserting a new register into a block at the lower end the present
bitmap is currently shifted into the wrong direction. The effect of this is
that the bitmap becomes corrupted and registers which are present might be
reported as not present and vice versa.
Fix this by shifting left rather than right.
Fixes: 472fdec7380c("regmap: rbtree: Reduce number of nodes, take 2")
Reported-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1096be084a upstream.
The interrupt is enabled before the handler is set. Even this bug
did not appear, it is potentially dangerous as it can lead to a
NULL pointer dereference.
Fix the error by enabling the interrupt after
clockevents_config_and_register() is called.
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ecc758692 upstream.
For PGR reservation of type Write Exclusive Access, allow all non
reservation holding I_T nexuses with active registrations to READ
from the device.
This addresses a bug where active registrations that attempted
to READ would result in an reservation conflict.
Signed-off-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae450e246e upstream.
This patch changes core_scsi3_pro_release() logic to allow an
existing AllRegistrants type reservation to be re-reserved by
any registered I_T nexus.
This addresses a issue where AllRegistrants type RESERVE was
receiving RESERVATION_CONFLICT status if dev_pr_res_holder did
not match the same I_T nexus, instead of just returning GOOD
status following spc4r34 Section 5.9.9:
"If the device server receives a PERSISTENT RESERVE OUT command
with RESERVE service action where the TYPE field and the SCOPE
field contain the same values as the existing type and scope
from a persistent reservation holder, it shall not make any
change to the existing persistent reservation and shall complete
the command with GOOD status."
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c3c9baa0d upstream.
This patch fixes an issue with AllRegistrants reservations where
an unregister operation by the I_T nexus reservation holder would
incorrectly drop the reservation, instead of waiting until the
last active I_T nexus is unregistered as per SPC-4.
This includes updating __core_scsi3_complete_pro_release() to reset
dev->dev_pr_res_holder with another pr_reg for this special case,
as well as a new 'unreg' parameter to determine when the release
is occuring from an implicit unregister, vs. explicit RELEASE.
It also adds special handling in core_scsi3_free_pr_reg_from_nacl()
to release the left-over pr_res_holder, now that pr_reg is deleted
from pr_reg_list within __core_scsi3_complete_pro_release().
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d16ca7c519 upstream.
This patch fixes the usage of R_HOLDER bit for an All Registrants
reservation in READ_FULL_STATUS, where only the registration who
issued RESERVE was being reported as having an active reservation.
It changes core_scsi3_pri_read_full_status() to check ahead of the
list walk of active registrations to see if All Registrants is active,
and if so set R_HOLDER bit and scope/type fields for all active
registrations.
Reported-by: Ilias Tsitsimpis <i.tsitsimpis@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 215a8fe419 upstream.
This patch fixes a NULL pointer dereference OOPs with pSCSI backends
within target_core_stat.c code. The bug is caused by a configfs attr
read if no pscsi_dev_virt->pdv_sd has been configured.
Reported-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f068fbc82e upstream.
This patch fixes a iser specific logout bug where early complete()
of conn->conn_logout_comp in iscsit_close_connection() was causing
isert_wait4logout() to complete too soon, triggering a use after
free NULL pointer dereference of iscsi_conn memory.
The complete() was originally added for traditional iscsi-target
when a ISCSI_LOGOUT_OP failed in iscsi_target_rx_opcode(), but given
iser-target does not wait in logout failure, this special case needs
to be avoided.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f7da044f8 upstream.
This patch fixes a NULL pointer dereference triggered by a late
target_configure_device() -> alloc_workqueue() failure that results
in target_free_device() being called with DF_CONFIGURED already set,
which subsequently OOPses in destroy_workqueue() code.
Currently this only happens at modprobe target_core_mod time when
core_dev_setup_virtual_lun0() -> target_configure_device() fails,
and the explicit target_free_device() gets called.
To address this bug originally introduced by commit 0fd97ccf45, go
ahead and move DF_CONFIGURED to end of target_configure_device()
code to handle this special failure case.
Reported-by: Claudio Fleiner <cmf@daterainc.com>
Cc: Claudio Fleiner <cmf@daterainc.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7544e59734 upstream.
This patch fixes a se_cmd->cmd_kref leak buf when se_sess->sess_tearing_down
is true within target_get_sess_cmd() submission path code.
This se_cmd reference leak can occur during active session shutdown when
ack_kref=1 is passed by target_submit_cmd_[map_sgls,tmr]() callers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af6fc858a3 upstream.
Otherwise the guest can abuse that control to cause e.g. PCIe
Unsupported Request responses by disabling memory and/or I/O decoding
and subsequently causing (CPU side) accesses to the respective address
ranges, which (depending on system configuration) may be fatal to the
host.
Note that to alter any of the bits collected together as
PCI_COMMAND_GUEST permissive mode is now required to be enabled
globally or on the specific device.
This is CVE-2015-2150 / XSA-120.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e40b0539 upstream.
Using the pvops kernel a NULL pointer dereference was detected on a
large machine (144 processors) when booting as dom0 in
evtchn_fifo_unmask() during assignment of a pirq.
The event channel in question was the first to need a new entry in
event_array[] in events_fifo.c. Unfortunately xen_irq_info_pirq_setup()
is called with evtchn being 0 for a new pirq and the real event channel
number is assigned to the pirq only during __startup_pirq().
It is mandatory to call xen_evtchn_port_setup() after assigning the
event channel number to the pirq to make sure all memory needed for the
event channel is allocated.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3458390b9f upstream.
To take down the MOB and GMR memory types, the driver may have to issue
fence objects and thus make sure that the fence manager is taken down
after those memory types.
Reorder device init accordingly.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29d62ec5f8 upstream.
Normally _regulator_do_enable() isn't called on an already-enabled
rdev. That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.
However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish(). While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.
At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin. Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled. This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.
Here's how the reference counting works here:
* Each time _regulator_enable() is called we increment
rdev->use_count, so _regulator_enable() calls need to be balanced
with _regulator_disable() calls.
* There is no explicit reference counting in _regulator_do_enable()
which is normally just a warapper around rdev->desc->ops->enable()
with code for supporting delays. It's not expected that the
"ops->enable()" call do reference counting.
* Since regulator_ena_gpio_ctrl() does have reference counting
(handling the sharing of the pin amongst multiple rdevs), we
shouldn't call it if the current rdev is already enabled.
Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register(). In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled. regulator_register() was initting it
as the actual state of the pin.
Fixes: 967cfb18c0 ("regulator: core: manage enable GPIO list")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0548bf4f5a upstream.
The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator. However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator. That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings. We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.
Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish(). That may speed up suspend/resume and also
avoids exposing hidden bugs.
[Use much clearer commit message from Doug Anderson]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da29370056 upstream.
EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dad0386b9 upstream.
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd6fa8d2ca upstream.
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76e1d14b31 upstream.
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62dfd912ab upstream.
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 969439016d upstream.
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2e0ea8611 upstream.
I'm still receiving reports to my email address, so let's point this
at the linux-serial mailing list instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeb8a7e8bb upstream.
when multiport is off, virtio console invokes config access from irq
context, config access is blocking on s390.
Fix this up by scheduling work from config irq - similar to what we do
for multiport configs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f6e24ed9d upstream.
when multiport is off, we don't initialize config work,
but we then cancel uninitialized control_work on freeze.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a17d4996e0 upstream.
Just keep it working, seems to fix some PLL problems.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=73378
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77ae5f4b48 upstream.
Need to double the viewport height.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54acf107e4 upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0586915ec1 upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cffefd9bb3 upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d1393f23d upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f957063fee upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c320bb5f6d upstream.
To make sure the writes go through the pci bridge.
bug:
https://bugzilla.kernel.org/show_bug.cgi?id=90741
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8d006e0105 ]
This reverts commit 11ad714b98 because
it breaks cx82310_eth.
The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e7f3db14ea (89bb35e200 upstream) was backported incorrectly by me, so fix it up, as the driver is now broken.
Sorry about that.
Reported-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
