commit 61882b6317 upstream.
The two functions s3c2416_cpufreq_driver_init and s3c_cpufreq_register
are marked init but are called from a context that might be run after
the __init sections are discarded, as the compiler points out:
WARNING: vmlinux.o(.data+0x1ad9dc): Section mismatch in reference from the variable s3c2416_cpufreq_driver to the function .init.text:s3c2416_cpufreq_driver_init()
WARNING: drivers/built-in.o(.text+0x35b5dc): Section mismatch in reference from the function s3c2410a_cpufreq_add() to the function .init.text:s3c_cpufreq_register()
This removes the __init markings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d4eda237 upstream.
On Dell Latitude C600 laptop with Pentium 3 850MHz processor, the
speedstep-smi driver sometimes loads and sometimes doesn't load with
"change to state X failed" message.
The hardware sometimes refuses to change frequency and in this case, we
need to retry later. I found out that we need to enable interrupts while
waiting. When we enable interrupts, the hardware blockage that prevents
frequency transition resolves and the transition is possible. With
disabled interrupts, the blockage doesn't resolve (no matter how long do
we wait). The exact reasons for this hardware behavior are unknown.
This patch enables interrupts in the function speedstep_set_state that can
be called with disabled interrupts. However, this function is called with
disabled interrupts only from speedstep_get_freqs, so it shouldn't cause
any problem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ffae8c06f upstream.
In __cpufreq_remove_dev_finish(), per-cpu 'cpufreq_cpu_data' needs
to be cleared before calling kobject_put(&policy->kobj) and under
cpufreq_driver_lock. Otherwise, if someone else calls cpufreq_cpu_get()
in parallel with it, they can obtain a non-NULL policy from that after
kobject_put(&policy->kobj) was executed.
Consider this case:
Thread A Thread B
cpufreq_cpu_get()
acquire cpufreq_driver_lock
read-per-cpu cpufreq_cpu_data
kobject_put(&policy->kobj);
kobject_get(&policy->kobj);
...
per_cpu(&cpufreq_cpu_data, cpu) = NULL
And this will result in a warning like this one:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at include/linux/kref.h:47
kobject_get+0x41/0x50()
Modules linked in: acpi_cpufreq(+) nfsd auth_rpcgss nfs_acl
lockd grace sunrpc xfs libcrc32c sd_mod ixgbe igb mdio ahci hwmon
...
Call Trace:
[<ffffffff81661b14>] dump_stack+0x46/0x58
[<ffffffff81072b61>] warn_slowpath_common+0x81/0xa0
[<ffffffff81072c7a>] warn_slowpath_null+0x1a/0x20
[<ffffffff812e16d1>] kobject_get+0x41/0x50
[<ffffffff815262a5>] cpufreq_cpu_get+0x75/0xc0
[<ffffffff81527c3e>] cpufreq_update_policy+0x2e/0x1f0
[<ffffffff810b8cb2>] ? up+0x32/0x50
[<ffffffff81381aa9>] ? acpi_ns_get_node+0xcb/0xf2
[<ffffffff81381efd>] ? acpi_evaluate_object+0x22c/0x252
[<ffffffff813824f6>] ? acpi_get_handle+0x95/0xc0
[<ffffffff81360967>] ? acpi_has_method+0x25/0x40
[<ffffffff81391e08>] acpi_processor_ppc_has_changed+0x77/0x82
[<ffffffff81089566>] ? move_linked_works+0x66/0x90
[<ffffffff8138e8ed>] acpi_processor_notify+0x58/0xe7
[<ffffffff8137410c>] acpi_ev_notify_dispatch+0x44/0x5c
[<ffffffff8135f293>] acpi_os_execute_deferred+0x15/0x22
[<ffffffff8108c910>] process_one_work+0x160/0x410
[<ffffffff8108d05b>] worker_thread+0x11b/0x520
[<ffffffff8108cf40>] ? rescuer_thread+0x380/0x380
[<ffffffff81092421>] kthread+0xe1/0x100
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
[<ffffffff81669ebc>] ret_from_fork+0x7c/0xb0
[<ffffffff81092340>] ? kthread_create_on_node+0x1b0/0x1b0
---[ end trace 89e66eb9795efdf7 ]---
The actual code flow is as follows:
Thread A: Workqueue: kacpi_notify
acpi_processor_notify()
acpi_processor_ppc_has_changed()
cpufreq_update_policy()
cpufreq_cpu_get()
kobject_get()
Thread B: xenbus_thread()
xenbus_thread()
msg->u.watch.handle->callback()
handle_vcpu_hotplug_event()
vcpu_hotplug()
cpu_down()
__cpu_notify(CPU_POST_DEAD..)
cpufreq_cpu_callback()
__cpufreq_remove_dev_finish()
cpufreq_policy_put_kobj()
kobject_put()
cpufreq_cpu_get() gets the policy from per-cpu variable cpufreq_cpu_data
under cpufreq_driver_lock, and once it gets a valid policy it expects it
to not be freed until cpufreq_cpu_put() is called.
But the race happens when another thread puts the kobject first and updates
cpufreq_cpu_data before or later. And so the first thread gets a valid policy
structure and before it does kobject_get() on it, the second one has already
done kobject_put().
Fix this by setting cpufreq_cpu_data to NULL before putting the kobject and that
too under locks.
Reported-by: Ethan Zhao <ethan.zhao@oracle.com>
Reported-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d022a65ed2 upstream.
Using a VID value that is not high enough for the requested P state can
cause machine checks. Add a ceiling function to ensure calulated VIDs
with fractional values are set to the next highest integer VID value.
The algorythm for calculating the non-trubo VID from the BIOS writers
guide is:
vid_ratio = (vid_max - vid_min) / (max_pstate - min_pstate)
vid = ceiling(vid_min + (req_pstate - min_pstate) * vid_ratio)
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b27580b05e upstream.
BYT has a different conversion from P state to frequency than the core
processors. This causes the min/max and current frequency to be
misreported on some BYT SKUs. Tested on BYT N2820, Ivybridge and
Haswell processors.
Link: https://bugzilla.yoctoproject.org/show_bug.cgi?id=6663
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16405f98bc upstream.
This is pretty much the same as Intel Baytrail, only the CPU ID is
different. Add the new ID to the supported CPU list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36b4bed5cd upstream.
Code which changes policy to powersave changes also max_policy_pct based on
max_freq. Code which change max_perf_pct has upper limit base on value
max_policy_pct. When policy is changing from powersave back to performance
then max_policy_pct is not changed. Which means that changing max_perf_pct is
not possible to high values if max_freq was too low in powersave policy.
Test case:
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq
800000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
100
$ echo powersave > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 800000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 20 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
powersave
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
800000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
20
$ echo performance > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
$ echo 3300000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
$ echo 100 > /sys/devices/system/cpu/intel_pstate/max_perf_pct
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
performance
$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq
3300000
$ cat /sys/devices/system/cpu/intel_pstate/max_perf_pct
24
And now intel_pstate driver allows to set maximal value for max_perf_pct based
on max_policy_pct which is 24 for previous powersave max_freq 800000.
This patch will set default value for max_policy_pct when setting policy to
performance so it will allow to set also max value for max_perf_pct.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c034b02e21 upstream.
Currently the core does not expose scaling_cur_freq for set_policy()
drivers this breaks some userspace monitoring tools.
Change the core to expose this file for all drivers and if the
set_policy() driver supports the get() callback use it to retrieve the
current frequency.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=73741
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d62dbf77f7 upstream.
When building this driver as a module, we get a helpful warning
about the return type:
drivers/cpufreq/integrator-cpufreq.c:232:2: warning: initialization from incompatible pointer type
.remove = __exit_p(integrator_cpufreq_remove),
If the remove callback returns void, the caller gets an undefined
value as it expects an integer to be returned. This fixes the
problem by passing down the value from cpufreq_unregister_driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7106e02bae upstream.
While debugging a cpufreq-related hardware failure on a system I saw the
following lockdep warning:
=========================
[ BUG: held lock freed! ] 3.17.0-rc4+ #1 Tainted: G E
-------------------------
insmod/2247 is freeing memory ffff88006e1b1400-ffff88006e1b17ff, with a lock still held there!
(&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
3 locks held by insmod/2247:
#0: (subsys mutex#5){+.+.+.}, at: [<ffffffff81485579>] subsys_interface_register+0x69/0x120
#1: (cpufreq_rwsem){.+.+.+}, at: [<ffffffff8156cf73>] __cpufreq_add_dev.isra.21+0x73/0xb80
#2: (&policy->rwsem){+.+...}, at: [<ffffffff8156d37d>] __cpufreq_add_dev.isra.21+0x47d/0xb80
stack backtrace:
CPU: 0 PID: 2247 Comm: insmod Tainted: G E 3.17.0-rc4+ #1
Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 08/24/2013
0000000000000000 000000008f3063c4 ffff88006f87bb30 ffffffff8171b358
ffff88006bcf3750 ffff88006f87bb68 ffffffff810e09e1 ffff88006e1b1400
ffffea0001b86c00 ffffffff8156d327 ffff880073003500 0000000000000246
Call Trace:
[<ffffffff8171b358>] dump_stack+0x4d/0x66
[<ffffffff810e09e1>] debug_check_no_locks_freed+0x171/0x180
[<ffffffff8156d327>] ? __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff8121412b>] kfree+0xab/0x2b0
[<ffffffff8156d327>] __cpufreq_add_dev.isra.21+0x427/0xb80
[<ffffffff81724cf7>] ? _raw_spin_unlock+0x27/0x40
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff8156da8e>] cpufreq_add_dev+0xe/0x10
[<ffffffff814855d1>] subsys_interface_register+0xc1/0x120
[<ffffffff8156bcf2>] cpufreq_register_driver+0x112/0x340
[<ffffffff8121415a>] ? kfree+0xda/0x2b0
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffffa003562e>] pcc_cpufreq_init+0x4af/0xe81 [pcc_cpufreq]
[<ffffffffa003517f>] ? pcc_cpufreq_do_osc+0x17f/0x17f [pcc_cpufreq]
[<ffffffff81002144>] do_one_initcall+0xd4/0x210
[<ffffffff811f7472>] ? __vunmap+0xd2/0x120
[<ffffffff81127155>] load_module+0x1315/0x1b70
[<ffffffff811222a0>] ? store_uevent+0x70/0x70
[<ffffffff811229d9>] ? copy_module_from_fd.isra.44+0x129/0x180
[<ffffffff81127b86>] SyS_finit_module+0xa6/0xd0
[<ffffffff81725b69>] system_call_fastpath+0x16/0x1b
cpufreq: __cpufreq_add_dev: ->get() failed
insmod: ERROR: could not insert module pcc-cpufreq.ko: No such device
The warning occurs in the __cpufreq_add_dev() code which does
down_write(&policy->rwsem);
...
if (cpufreq_driver->get && !cpufreq_driver->setpolicy) {
policy->cur = cpufreq_driver->get(policy->cpu);
if (!policy->cur) {
pr_err("%s: ->get() failed\n", __func__);
goto err_get_freq;
}
If cpufreq_driver->get(policy->cpu) returns an error we execute the
code at err_get_freq, which does not up the policy->rwsem. This causes
the lockdep warning.
Trivial patch to up the policy->rwsem in the error path.
After the patch has been applied, and an error occurs in the
cpufreq_driver->get(policy->cpu) call we will now see
cpufreq: __cpufreq_add_dev: ->get() failed
cpufreq: __cpufreq_add_dev: ->get() failed
modprobe: ERROR: could not insert 'pcc_cpufreq': No such device
Fixes: 4e97b631f2 (cpufreq: Initialize governor for a new policy under policy->rwsem)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92c14bd947 upstream.
This is only relevant to implementations with multiple clusters, where clusters
have separate clock lines but all CPUs within a cluster share it.
Consider a dual cluster platform with 2 cores per cluster. During suspend we
start hot unplugging CPUs in order 1 to 3. When CPU2 is removed, policy->kobj
would be moved to CPU3 and when CPU3 goes down we wouldn't free policy or its
kobj as we want to retain permissions/values/etc.
Now on resume, we will get CPU2 before CPU3 and will call __cpufreq_add_dev().
We will recover the old policy and update policy->cpu from 3 to 2 from
update_policy_cpu().
But the kobj is still tied to CPU3 and isn't moved to CPU2. We wouldn't create a
link for CPU2, but would try that for CPU3 while bringing it online. Which will
report errors as CPU3 already has kobj assigned to it.
This bug got introduced with commit 42f921a, which overlooked this scenario.
To fix this, lets move kobj to the new policy->cpu while bringing first CPU of a
cluster back. Also do a WARN_ON() if kobject_move failed, as we would reach here
only for the first CPU of a non-boot cluster. And we can't recover from this
situation, if kobject_move() fails.
Fixes: 42f921a6f1 (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Reported-and-tested-by: Bu Yitian <ybu@qti.qualcomm.com>
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 179e847167 upstream.
Ensure that cpu->cpu is set before writing MSR_IA32_PERF_CTL during CPU
initialization. Otherwise only cpu0 has its P-state set and all other
cores are left with their values unchanged.
In most cases, this is not too serious because the P-states will be set
correctly when the timer function is run. But when the default governor
is set to performance, the per-CPU current_pstate stays the same forever
and no attempts are made to write the MSRs again.
Signed-off-by: Vincent Minet <vincent@vincent-minet.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd5fbf70f9 upstream.
If turbo is disabled in the BIOS bit 38 should be set in
MSR_IA32_MISC_ENABLE register per section 14.3.2.1 of the SDM Vol 3
document 325384-050US Feb 2014. If this bit is set do *not* attempt
to disable trubo via the MSR_IA32_PERF_CTL register. On some systems
trying to disable turbo via MSR_IA32_PERF_CTL will cause subsequent
writes to MSR_IA32_PERF_CTL not take affect, in fact reading
MSR_IA32_PERF_CTL will not show the IDA/Turbo DISENGAGE bit(32) as
set. A write of bit 32 to zero returns to normal operation.
Also deal with the case where the processor does not support
turbo and the BIOS does not report the fact in MSR_IA32_MISC_ENABLE
but does report the max and turbo P states as the same value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=64251
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c16ed06024 upstream.
Commit 21855ff5 (intel_pstate: Set turbo VID for BayTrail) introduced
setting the turbo VID which is required to prevent a machine check on
some Baytrail SKUs under heavy graphics based workloads. The
docmumentation update that brought the requirement to light also
changed the bit mask used for enumerating P state and VID values from
0x7f to 0x3f.
This change returns the mask value to 0x7f.
Tested with the Intel NUC DN2820FYK,
BIOS version FYBYT10H.86A.0034.2014.0513.1413 with v3.16-rc1 and
v3.14.8 kernel versions.
Fixes: 21855ff5 (intel_pstate: Set turbo VID for BayTrail)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77951
Reported-and-tested-by: Rune Reterson <rune@megahurts.dk>
Reported-and-tested-by: Eric Eickmeyer <erich@ericheickmeyer.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a90af67c2 upstream.
Since commtit 8a7b1227e3 (cpufreq: davinci: move cpufreq driver to
drivers/cpufreq) this added dependancy only for CONFIG_ARCH_DAVINCI_DA850
where as davinci_cpufreq_init() call is used by all davinci platform.
This patch fixes following build error:
arch/arm/mach-davinci/built-in.o: In function `davinci_init_late':
:(.init.text+0x928): undefined reference to `davinci_cpufreq_init'
make: *** [vmlinux] Error 1
Fixes: 8a7b1227e3 (cpufreq: davinci: move cpufreq driver to drivers/cpufreq)
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51d211e9c3 upstream.
There was a mistake in the actual rounding portion this previous patch:
f0fe3cd7e1 (intel_pstate: Correct rounding in busy calculation) such that
the rounding was asymetric and incorrect.
Severity: Not very serious, but can increase target pstate by one extra value.
For real world work flows the issue should self correct (but I have no proof).
It is the equivalent of different PID gains for positive and negative numbers.
Examples:
-3.000000 used to round to -4, rounds to -3 with this patch.
-3.503906 used to round to -5, rounds to -4 with this patch.
Fixes: f0fe3cd7e1 (intel_pstate: Correct rounding in busy calculation)
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf8102228a upstream.
This change makes the busy calculation using 64 bit math which prevents
overflow for large values of aperf/mperf.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4ee841f60 upstream.
The PID assumes that samples are of equal time, which for a deferable
timers this is not true when the system goes idle. This causes the
PID to take a long time to converge to the min P state and depending
on the pattern of the idle load can make the P state appear stuck.
The hold-off value of three sample times before using the scaling is
to give a grace period for applications that have high performance
requirements and spend a lot of time idle, The poster child for this
behavior is the ffmpeg benchmark in the Phoronix test suite.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0fe3cd7e1 upstream.
Changing to fixed point math throughout the busy calculation in
commit e66c1768 (Change busy calculation to use fixed point
math.) Introduced some inaccuracies by rounding the busy value at two
points in the calculation. This change removes roundings and moves
the rounding to the output of the PID where the calculations are
complete and the value returned as an integer.
Fixes: e66c176837 (intel_pstate: Change busy calculation to use fixed point math.)
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adacdf3f2b upstream.
Commit fcb6a15c (intel_pstate: Take core C0 time into account for core
busy calculation) introduced a regression referenced below. The issue
with "lockup" after suspend that this commit was addressing is now dealt
with in the suspend path.
Fixes: fcb6a15c2e (intel_pstate: Take core C0 time into account for core busy calculation)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=66581
Link: https://bugzilla.kernel.org/show_bug.cgi?id=75121
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d37e2b7644 upstream.
Remove unneeded sample buffers, intel_pstate operates on the most
recent sample only. This save some memory and make the code more
readable.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3beb0ac52 upstream.
This driver is using devres managed calls incorrectly, giving the cpu0
device as first parameter instead of the cpufreq platform device.
This results in resources not being freed if the cpufreq platform device
is unbound, for example if probing has to be deferred for a missing
regulator.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d40a63c45b upstream.
Setting the P state of the core to max at init time is a hold over
from early implementation of intel_pstate where intel_pstate disabled
cpufreq and loaded VERY early in the boot sequence. This was to
ensure that intel_pstate did not affect boot time. This in not needed
now that intel_pstate is a cpufreq driver.
Removing this covers the case where a CPU has gone through a manual
CPU offline/online cycle and the P state is set to MAX on init and the
CPU immediately goes idle. Due to HW coordination the P state request
on the idle CPU will drag all cores to MAX P state until the load is
reevaluated when to core goes non-idle.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21855ff5bc upstream.
A documentation update exposed that there is a separate set of VID
values that must be used in the turbo/boost P state range. Add
enumerating and setting the correct VID for P states in the turbo
range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e8acb3296 upstream.
Loongson2 has been using (incorrectly) kHz for cpu_clk rate. This has
been unnoticed, as loongson2_cpufreq was the only place where the rate
was set/get. After commit 652ed95d5f
(cpufreq: introduce cpufreq_generic_get() routine) things however broke,
and now loops_per_jiffy adjustments are incorrect (1000 times too long).
The patch fixes this by changing cpu_clk rate to Hz.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: cpufreq@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/6678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4ddad9502 upstream.
Need use 'clk' instead of 'mclk', which is the original removed local
variable.
The related original commit:
"652ed95 cpufreq: introduce cpufreq_generic_get() routine"
The related error with allmodconfig for unicore32:
CC drivers/cpufreq/unicore2-cpufreq.o
drivers/cpufreq/unicore2-cpufreq.c: In function ‘ucv2_target’:
drivers/cpufreq/unicore2-cpufreq.c:48: error: ‘struct cpufreq_policy’ has no member named ‘mclk’
make[2]: *** [drivers/cpufreq/unicore2-cpufreq.o] Error 1
make[1]: *** [drivers/cpufreq] Error 2
make: *** [drivers] Error 2
Fixes: 652ed95d5f (cpufreq: introduce cpufreq_generic_get() routine)
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ca97886fe upstream.
Earlier commit:
commit 652ed95d5f
Author: Viresh Kumar <viresh.kumar@linaro.org>
Date: Thu Jan 9 20:38:43 2014 +0530
cpufreq: introduce cpufreq_generic_get() routine
did some changes to driver and by mistake made cpuclk as a 'static' local
variable, which wasn't actually required. Fix it.
Fixes: 652ed95d5f (cpufreq: introduce cpufreq_generic_get() routine)
Reported-by: Alexandre Oliva <lxoliva@fsfla.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ed672292 upstream.
Earlier commit:
commit 652ed95d5f
Author: Viresh Kumar <viresh.kumar@linaro.org>
Date: Thu Jan 9 20:38:43 2014 +0530
cpufreq: introduce cpufreq_generic_get() routine
did some changes to driver and by mistake made cpuclk as a 'static' local
variable, which wasn't actually required. Fix it.
Fixes: 652ed95d5f (cpufreq: introduce cpufreq_generic_get() routine)
Reported-by: Alexandre Oliva <lxoliva@fsfla.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit da60ce9f2f (cpufreq: call cpufreq_driver->get() after
calling ->init()) __cpufreq_add_dev() sometimes fails for CPUs handled
by intel_pstate, because that driver may return 0 from its ->get()
callback if it has not run long enough to collect enough samples on the
given CPU. That didn't happen before commit da60ce9f2f which added
policy->cur initialization to __cpufreq_add_dev() to help reduce code
duplication in other cpufreq drivers.
However, the code added by commit da60ce9f2f need not be executed
for cpufreq drivers having the ->setpolicy callback defined, because
the subsequent invocation of cpufreq_set_policy() will use that
callback to initialize the policy anyway and it doesn't need
policy->cur to be initialized upfront. The analogous code in
cpufreq_update_policy() is also unnecessary for cpufreq drivers
having ->setpolicy set and may be skipped for them as well.
Since intel_pstate provides ->setpolicy, skipping the upfront
policy->cur initialization for cpufreq drivers with that callback
set will cover intel_pstate and the problem it's been having after
commit da60ce9f2f will be addressed.
Fixes: da60ce9f2f (cpufreq: call cpufreq_driver->get() after calling ->init())
References: https://bugzilla.kernel.org/show_bug.cgi?id=71931
Reported-and-tested-by: Patrik Lundquist <patrik.lundquist@gmail.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->rwsem is used to lock access to all parts of code modifying
struct cpufreq_policy, but it's not used on a new policy created by
__cpufreq_add_dev().
Because of that, if cpufreq_update_policy() is called in a tight loop
on one CPU in parallel with offline/online of another CPU, then the
following crash can be triggered:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
pgd = c0003000
[00000020] *pgd=80000000004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
PC is at __cpufreq_governor+0x10/0x1ac
LR is at cpufreq_update_policy+0x114/0x150
---[ end trace f23a8defea6cd706 ]---
Kernel panic - not syncing: Fatal exception
CPU0: stopping
CPU: 0 PID: 7136 Comm: mpdecision Tainted: G D W 3.10.0-gd727407-00074-g979ede8 #396
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58)
[<c02a23ac>] (__blocking_notifier_call_chain+0x40/0x58) from [<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c)
[<c02a23d8>] (blocking_notifier_call_chain+0x14/0x1c) from [<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8)
[<c0803c68>] (cpufreq_set_policy+0xd4/0x2b8) from [<c0803e7c>] (cpufreq_init_policy+0x30/0x98)
[<c0803e7c>] (cpufreq_init_policy+0x30/0x98) from [<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4)
[<c0805a18>] (__cpufreq_add_dev.isra.17+0x4dc/0x7a4) from [<c0805d38>] (cpufreq_cpu_callback+0x58/0x84)
[<c0805d38>] (cpufreq_cpu_callback+0x58/0x84) from [<c0afe180>] (notifier_call_chain+0x40/0x68)
[<c0afe180>] (notifier_call_chain+0x40/0x68) from [<c02812dc>] (__cpu_notify+0x28/0x44)
[<c02812dc>] (__cpu_notify+0x28/0x44) from [<c0aeed90>] (_cpu_up+0xf4/0x1dc)
[<c0aeed90>] (_cpu_up+0xf4/0x1dc) from [<c0aeeed4>] (cpu_up+0x5c/0x78)
[<c0aeeed4>] (cpu_up+0x5c/0x78) from [<c0aec808>] (store_online+0x44/0x74)
[<c0aec808>] (store_online+0x44/0x74) from [<c03a40f4>] (sysfs_write_file+0x108/0x14c)
[<c03a40f4>] (sysfs_write_file+0x108/0x14c) from [<c03517d4>] (vfs_write+0xd0/0x180)
[<c03517d4>] (vfs_write+0xd0/0x180) from [<c0351ca8>] (SyS_write+0x38/0x68)
[<c0351ca8>] (SyS_write+0x38/0x68) from [<c0205de0>] (ret_fast_syscall+0x0/0x30)
Fix that by taking locks at appropriate places in __cpufreq_add_dev()
as well.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Suggested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Policy must be fully initialized before it is being made available
for use by others. Otherwise cpufreq_cpu_get() would be able to grab
a half initialized policy structure that might not have affected_cpus
(for example) populated. Then, anybody accessing those fields will get
a wrong value and that will lead to unpredictable results.
In order to fix this, do all the necessary initialization before we
make the policy structure available via cpufreq_cpu_get(). That will
guarantee that any code accessing fields of the policy will get
correct data from them.
Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a module calls cpufreq_get while cpufreq is initializing, it's
possible for it to be called after cpufreq_driver is set but before
cpufreq_cpu_data is written during subsys_interface_register. This
happens because cpufreq_get doesn't take the cpufreq_driver_lock
around its use of cpufreq_cpu_data.
Fix this by using cpufreq_cpu_get(cpu) to look up the policy rather
than reading it out of cpufreq_cpu_data directly. cpufreq_cpu_get()
takes the appropriate locks to prevent this race from happening.
Since it's possible for policy to be NULL if the caller passes in an
invalid CPU number or calls the function before cpufreq is initialized,
delete the BUG_ON(!policy) and simply return 0. Don't try to return
-ENOENT because that's negative and the function returns an unsigned
integer.
References: https://bbs.archlinux.org/viewtopic.php?id=177934
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit fcb6a15c2e (intel_pstate: Take core C0 time into account for
core busy calculation) introduced a regression on some processor SKUs
supported by intel_pstate. This was due to the truncation caused by
using integer math to calculate core busy and C0 percentages.
On a i7-4770K processor operating at 800Mhz going to 100% utilization
the percent busy of the CPU using integer math is 22%, but it actually
is 22.85%. This value scaled to the current frequency returned 97
which the PID interpreted as no error and did not adjust the P state.
Tested on i7-4770K, i7-2600, i5-3230M.
Fixes: fcb6a15c2e (intel_pstate: Take core C0 time into account for core busy calculation)
References: https://lkml.org/lkml/2014/2/19/626
References: https://bugzilla.kernel.org/show_bug.cgi?id=70941
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A documentation update exposed the existance of the turbo ratio
register. Update baytrail support to use the turbo range.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
LFM (max efficiency ratio) is the max frequency at minimum voltage
supported by the processor. Using LFM as the minimum P state
increases performmance without affecting power. By not using P states
below LFM we avoid using P states that are less power efficient.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The powernow-k8 driver maintains a per-cpu data-structure called
powernow_data that is used to perform the frequency transitions.
It initializes this data structure only for the policy->cpu. So,
accesses to this data structure by other CPUs results in various
problems because they would have been uninitialized.
Specifically, if a cpu (!= policy->cpu) invokes the drivers' ->get()
function, it returns 0 as the KHz value, since its per-cpu memory
doesn't point to anything valid. This causes problems during
suspend/resume since cpufreq_update_policy() tries to enforce this
(0 KHz) as the current frequency of the CPU, and this madness gets
propagated to adjust_jiffies() as well. Eventually, lots of things
start breaking down, including the r8169 ethernet card, in one
particularly interesting case reported by Pierre Ossman.
Fix this by initializing the per-cpu data-structures of all the CPUs
in the policy appropriately.
References: https://bugzilla.kernel.org/show_bug.cgi?id=70311
Reported-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 42f921a (cpufreq: remove sysfs files for CPUs which failed to
come back after resume) tried to do this but missed this piece of code
to fix.
Currently we are getting this on suspend/resume:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 877 at fs/sysfs/dir.c:52 sysfs_warn_dup+0x68/0x84()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu1/cpufreq'
Modules linked in: brcmfmac brcmutil
CPU: 0 PID: 877 Comm: test-rtc-resume Not tainted 3.14.0-rc2-00259-g9398a10cd964 #12
[<c0015bac>] (unwind_backtrace) from [<c0011850>] (show_stack+0x10/0x14)
[<c0011850>] (show_stack) from [<c056e018>] (dump_stack+0x80/0xcc)
[<c056e018>] (dump_stack) from [<c0025e44>] (warn_slowpath_common+0x64/0x88)
[<c0025e44>] (warn_slowpath_common) from [<c0025efc>] (warn_slowpath_fmt+0x30/0x40)
[<c0025efc>] (warn_slowpath_fmt) from [<c012776c>] (sysfs_warn_dup+0x68/0x84)
[<c012776c>] (sysfs_warn_dup) from [<c0127a54>] (sysfs_do_create_link_sd+0xb0/0xb8)
[<c0127a54>] (sysfs_do_create_link_sd) from [<c038ef64>] (__cpufreq_add_dev.isra.27+0x2a8/0x814)
[<c038ef64>] (__cpufreq_add_dev.isra.27) from [<c038f548>] (cpufreq_cpu_callback+0x70/0x8c)
[<c038f548>] (cpufreq_cpu_callback) from [<c0043864>] (notifier_call_chain+0x44/0x84)
[<c0043864>] (notifier_call_chain) from [<c0025f60>] (__cpu_notify+0x28/0x44)
[<c0025f60>] (__cpu_notify) from [<c00261e8>] (_cpu_up+0xf0/0x140)
[<c00261e8>] (_cpu_up) from [<c0569eb8>] (enable_nonboot_cpus+0x68/0xb0)
[<c0569eb8>] (enable_nonboot_cpus) from [<c006339c>] (suspend_devices_and_enter+0x198/0x2dc)
[<c006339c>] (suspend_devices_and_enter) from [<c0063654>] (pm_suspend+0x174/0x1e8)
[<c0063654>] (pm_suspend) from [<c00624e0>] (state_store+0x6c/0xbc)
[<c00624e0>] (state_store) from [<c01fc200>] (kobj_attr_store+0x14/0x20)
[<c01fc200>] (kobj_attr_store) from [<c0126e50>] (sysfs_kf_write+0x44/0x48)
[<c0126e50>] (sysfs_kf_write) from [<c012a274>] (kernfs_fop_write+0xb4/0x14c)
[<c012a274>] (kernfs_fop_write) from [<c00d4818>] (vfs_write+0xa8/0x180)
[<c00d4818>] (vfs_write) from [<c00d4bb8>] (SyS_write+0x3c/0x70)
[<c00d4bb8>] (SyS_write) from [<c000e620>] (ret_fast_syscall+0x0/0x30)
---[ end trace 76969904b614c18f ]---
Fix this by removing sysfs link for cpufreq directory when cpu removed
isn't policy->cpu.
Revamps: 42f921a (cpufreq: remove sysfs files for CPUs which failed to come back after resume)
Reported-and-tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove the reporting of energy since it does not provide any useful
information about the state of the driver and will be a maintainance
headache going forward since the RAPL energy units register is not
architectural and subject to change between micro-architectures
References: https://bugzilla.kernel.org/show_bug.cgi?id=69831
Fixes: b69880f9cc (intel_pstate: Add trace point to report internal state.)
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Take non-idle time into account when calculating core busy time.
This ensures that intel_pstate will notice a decrease in load.
References: https://bugzilla.kernel.org/show_bug.cgi?id=66581
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- ACPI device hotplug fix preventing ACPI drivers from binding to device
objects that acpi_bus_trim() has been called for and the devices
represented by them may not be operational.
- Recent cpufreq changes related to the "boost" (turbo) feature broke
the acpi-cpufreq error code path causing a NULL pointer dereference
to occur on some systems. Fix from Konrad Rzeszutek Wilk.
- The log level of a CPU initialization error message added recently
needs to be reduced, because the particular BIOS issue indicated by
it turns out to be widespread and doesn't really matter for the
majority of systems having it. From Jiang Liu.
- The regulator API needs to be told to stay away from things on systems
with ACPI BIOSes or it may conflict with the BIOS' own handling of
voltage regulators. Fix from Mark Brown that works around a 3.13
regression in lm90 on PCs occuring if the regulator API is enabled.
- Prevent the Exynos4 devfreq driver from being built on multiplatform,
because it depends on things that aren't available during such builds.
From Sachin Kamat.
- Upstream ACPICA doesn't use the bool type as defined in the kernel,
so modify the kernel's ACPICA code to follow the upstream in that
respect (only one variable definition is affected) to reduce
divergences between the two. From Lv Zheng.
- Make the ACPI device PM code use ACPI_COMPANION() instead of its own
routine doing the same thing (and invokng ACPI_COMPANION() in the
process).
- Modify some routines in the ACPI processor driver to follow the
common convention and return negative integers on errors. From
Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=VBdN
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and cleanups from Rafael Wysocki:
- ACPI device hotplug fix preventing ACPI drivers from binding to device
objects that acpi_bus_trim() has been called for and the devices
represented by them may not be operational.
- Recent cpufreq changes related to the "boost" (turbo) feature broke
the acpi-cpufreq error code path causing a NULL pointer dereference
to occur on some systems. Fix from Konrad Rzeszutek Wilk.
- The log level of a CPU initialization error message added recently
needs to be reduced, because the particular BIOS issue indicated by
it turns out to be widespread and doesn't really matter for the
majority of systems having it. From Jiang Liu.
- The regulator API needs to be told to stay away from things on systems
with ACPI BIOSes or it may conflict with the BIOS' own handling of
voltage regulators. Fix from Mark Brown that works around a 3.13
regression in lm90 on PCs occuring if the regulator API is enabled.
- Prevent the Exynos4 devfreq driver from being built on multiplatform,
because it depends on things that aren't available during such builds.
From Sachin Kamat.
- Upstream ACPICA doesn't use the bool type as defined in the kernel,
so modify the kernel's ACPICA code to follow the upstream in that
respect (only one variable definition is affected) to reduce
divergences between the two. From Lv Zheng.
- Make the ACPI device PM code use ACPI_COMPANION() instead of its own
routine doing the same thing (and invokng ACPI_COMPANION() in the
process).
- Modify some routines in the ACPI processor driver to follow the
common convention and return negative integers on errors. From
Hanjun Guo.
* tag 'pm+acpi-3.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Clear match_driver flag in acpi_bus_trim()
ACPI / init: Flag use of ACPI and ACPI idioms for power supplies to regulator API
acpi-cpufreq: De-register CPU notifier and free struct msr on error.
ACPICA: Remove bool usage from ACPICA.
PM / devfreq: Disable Exynos4 driver build on multiplatform
ACPI / PM: Use ACPI_COMPANION() to get ACPI companions of devices
ACPI / scan: reduce log level of "ACPI: \_PR_.CPU4: failed to get CPU APIC ID"
ACPI / processor: Return specific error value when mapping lapic id
If cpufreq_register_driver() fails we would free the acpi driver
related structures but not free the ones allocated
by acpi_cpufreq_boost_init() function. This meant that as
the driver error-ed out and a CPU online/offline event came
we would crash and burn as one of the CPU notifiers would point
to garbage.
Fixes: cfc9c8ed03 (acpi-cpufreq: Adjust the code to use the common boost attribute)
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull thermal management updates from Zhang Rui:
"This time, the biggest change is the work of representing hardware
thermal properties in device tree infrastructure.
This work includes the introduction of a device tree bindings for
describing the hardware thermal behavior and limits, and also a parser
to read and interpret the data, and build thermal zones and thermal
binding parameters. It also contains three examples on how to use the
new representation on sensor devices, using three different drivers to
accomplish it. One driver is in thermal subsystem, the TI SoC
thermal, and the other two drivers are in hwmon subsystem.
Actually, this would be the first step of the complete work because we
still need to check other potential drivers to be converted and then
validate the proposed API. But the reason why I include it in this
pull request is that, first, this change does not hurt any others
without using this approach, second, the principle and concept of this
change would not break after converting the remaining drivers. BTW,
as you can see, there are several points in this change that do not
belong to thermal subsystem. Because it has been suggested by Guenter
R that in such cases, it is recommended to send the complete series
via one single subsystem.
Specifics:
- representing hardware thermal properties in device tree
infrastructure
- fix a regression that the imx thermal driver breaks system suspend.
- introduce ACPI INT3403 thermal driver to retrieve temperature data
from the INT3403 ACPI device object present on some systems.
- introduce debug statement for thermal core and step_wise governor.
- assorted fixes and cleanups for thermal core, cpu cooling, exynos
thrmal, intel powerclamp and imx thermal driver"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: remove const flag from .ops of imx thermal
Thermal: update thermal zone device after setting emul_temp
intel_powerclamp: Fix cstate counter detection.
thermal: imx: add necessary clk operation
Thermal cpu cooling: return error if no valid cpu frequency entry
thermal: fix cpu_cooling max_level behavior
thermal: rcar-thermal: Enable driver compilation with COMPILE_TEST
thermal: debug: add debug statement for core and step_wise
thermal: imx_thermal: add module device table
drivers: thermal: Mark function as static in x86_pkg_temp_thermal.c
thermal:samsung: fix compilation warning
thermal: imx: correct suspend/resume flow
thermal: exynos: fix error return code
Thermal: ACPI INT3403 thermal driver
MAINTAINERS: add thermal bindings entry in thermal domain
arm: dts: make OMAP4460 bandgap node to belong to OCP
arm: dts: make OMAP443x bandgap node to belong to OCP
arm: dts: add cooling properties on omap5 cpu node
arm: dts: add omap5 thermal data
arm: dts: add omap5 CORE thermal data
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJS3a1eAAoJEILEb/54YlRxnTgP/iGawvgjKWm6Qqp7WSIvd5gQ
zZ6q75C6Pc/W2fq1+OzVGnpCF8WYFy+nFDAXOvUHjIXuoxSwFcuW5l4aMckgl/0a
TXEWe9MJrCHHRfDApfFacCJ44U02bjJAD5vTyL/hKA+IHeinq4WCSojryYC+8jU0
cBrUIV0aNH8r5JR2WJNAyv/U29rXsDUOu0I4qTqZ4YaZT6AignMjtLXn1e9AH1Pn
DPZphTIo/HMnb+kgBOjt4snMk+ahVO9eCOxh/hH8ecnWExw9WynXoU5Nsna0tSZs
ssyHC7BYexD3oYsG8D52cFUpp4FCsJ0nFQNa2kw0LY+0FBNay43LySisKYHZPXEs
2WpESDv+/t7yhtnrvM+TtA7aBheKm2XMWGFSu/aERLE17jIidOkXKH5Y7ryYLNf/
uyRKxNS0NcZWZ0G+/wuY02jQYNkfYz3k/nTr8BAUItRBjdporGIRNEnR9gPzgCUC
uQhjXWMPulqubr8xbyefPWHTEzU2nvbXwTUWGjrBxSy8zkyy5arfqizUj+VG6afT
NsboANoMHa9b+xdzigSFdA3nbVK6xBjtU6Ywntk9TIpODKF5NgfARx0H+oSH+Zrj
32bMzgZtHw/lAbYsnQ9OnTY6AEWQYt6NMuVbTiLXrMHhM3nWwfg/XoN4nZqs6jPo
IYvE6WhQZU6L6fptGHFC
=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Add a special driver data flag (CPUFREQ_BOOST_FREQ) to indicate
a frequency that can be only enabled for BOOST mode.
This frequency will be used only for limited time, since running with
it for too long may cause the target device to overheat.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq_driver's boost_supported flag is true only when boost
support is explicitly enabled. Boost related attributes are exported
only under the same condition.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add CONFIG_CPU_FREQ_BOOST_SW Kconfig option such that software-managed
boost is enabled only after selecting "EXYNOS Frequency Overclocking -
Software". It also depends on the thermal subsystem to be compiled in,
which is necessary for disabling boost and cooling down the device when
overheating is detected.
Software-managed boost _MUST_ _NOT_ be enabled without thermal subsystem
with properly defined overheating temperature thresholds.
This option doesn't affect the x86's hardware-driven boost support
in the acpi-cpufreq driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
