commit 391949b6f0 upstream.
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd6fa8d2ca upstream.
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76e1d14b31 upstream.
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c957e8f084 upstream.
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
PGD 78bb8067 PUD 37712067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 11 Comm: ksoftirqd/1 Tainted: G O 3.18.0-rc4-mjo #5
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS MNW2CRB1.X64.0071.R30.1408131301 08/13/2014
task: ffff880077f9f290 ti: ffff88007a820000 task.ti: ffff88007a820000
RIP: 0010:[<ffffffffa0022bc8>] [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
RSP: 0018:ffff88007a823d08 EFLAGS: 00010202
RAX: 0000000000000008 RBX: ffff8800379a4430 RCX: 0000000000000026
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff8800379a4430
RBP: ffff88007a823d18 R08: 00000000ffffffff R09: 000000007a9bc65a
R10: 000000000000028f R11: 0000000000000005 R12: ffff880070123e98
R13: ffff880070123de8 R14: 0000000000000100 R15: ffffc90004888000
FS: 0000000000000000(0000) GS:ffff880079a80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000048 CR3: 000000007029b000 CR4: 00000000001007e0
Stack:
ffff88007a823d58 ffff8800379a4430 ffff88007a823d48 ffffffffa0022c89
0000000000000000 ffff8800379a4430 0000000000000000 0000000000000006
ffff88007a823da8 ffffffffa0023be0 ffff88007a823dd8 ffffffff81076204
Call Trace:
[<ffffffffa0022c89>] giveback+0x69/0xa0 [spi_pxa2xx_platform]
[<ffffffffa0023be0>] pump_transfers+0x710/0x740 [spi_pxa2xx_platform]
[<ffffffff81076204>] ? pick_next_task_fair+0x744/0x830
[<ffffffff81049679>] tasklet_action+0xa9/0xe0
[<ffffffff81049a0e>] __do_softirq+0xee/0x280
[<ffffffff81049bc0>] run_ksoftirqd+0x20/0x40
[<ffffffff810646df>] smpboot_thread_fn+0xff/0x1b0
[<ffffffff810645e0>] ? SyS_setgroups+0x150/0x150
[<ffffffff81060f9d>] kthread+0xcd/0xf0
[<ffffffff81060ed0>] ? kthread_create_on_node+0x180/0x180
[<ffffffff8187a82c>] ret_from_fork+0x7c/0xb0
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bf9cda4b upstream.
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4302a59629 upstream.
When used via spidev with more than one messages to tranfer via
SPI_IOC_MESSAGE the current implementation would return with
-EINVAL, since bits_per_word and speed_hz are set in all
transfer structs. And in the 2nd loop status will stay at
-EINVAL as its not overwritten again via fsl_spi_setup_transfer().
This patch changes this behavious by first checking if one of
the messages uses different settings. If this is the case
the function will return with -EINVAL. If not, the messages
are transferred correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: Esben Haabendal <esbenhaabendal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a8727e697 upstream.
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b9375b91b upstream.
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a50585 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5cc7b04740 upstream.
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ffa6158f0 upstream.
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e45ef682c upstream.
Do full clean up at exit, means terminate all ongoing DMA transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb57862ead upstream.
If the driver was compiled with DMA support, but DMA channels weren't acquired
by some reason, mid_spi_dma_exit() will crash the kernel.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b41583e729 upstream.
In case of 8 bit mode and DMA usage we end up with every second byte written as
0. We have to respect bits_per_word settings what this patch actually does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9d5d6fe16 upstream.
The commit 04f421e7 "spi: dw: use managed resources" changes drivers to use
managed functions, but seems wasn't properly tested in PCI case. The regs field
of struct dw_spi left uninitialized. Thus, kernel crashes when tries to access
to the SPI controller registers. This patch fixes the issue.
Fixes: 04f421e7 (spi: dw: use managed resources)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d0763c006 upstream.
The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: Jorge A. Ventura <jorge.araujo.ventura@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aca2636468 upstream.
The SPI host controller is the same as used in Baytrail, only the ACPI ID
is different so add this new ID to the list.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97ca0d6cc1 upstream.
Commit id 2bd16e3e23
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.
Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).
Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e06871cd2c upstream.
In commit f814f9ac5a ("spi/orion: add device tree binding"), Device
Tree support was added to the spi-orion driver. However, this commit
reads the "cell-index" property, without taking into account the fact
that DT properties are big-endian encoded.
Since most of the platforms using spi-orion with DT have apparently
not used anything but cell-index = <0>, the problem was not
visible. But as soon as one starts using cell-index = <1>, the problem
becomes clearly visible, as the master->bus_num gets a wrong value
(actually it gets the value 0, which conflicts with the first bus that
has cell-index = <0>).
This commit fixes that by using of_property_read_u32() to read the
property value, which does the appropriate endianness conversion when
needed.
Fixes: f814f9ac5a ("spi/orion: add device tree binding")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83596fbeb5 upstream.
The availability of SPI Dual or Quad Transfer Mode as indicated by the
"spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is
a hardware property of the SPI master, SPI slave, and board wiring. Hence
the SPI core should not reject an SPI slave because an SPI master driver
doesn't (yet) support Dual or Quad Transfer Mode.
Change the lack of Dual or Quad Transfer Mode support in the SPI master
driver from an error condition to a warning condition, and ignore the
unsupported mode bits, falling back to Single Transfer Mode, to avoid
breakages when running old kernels with new device trees.
Fixes: f477b7fb13 (spi: DUAL and QUAD support)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c63f5da008 upstream.
With devm_kzalloc, the memory is automatically freed when spi_device detach from
the bus.
Fixes: commit 43f627ac9d (spi: dw: fix memory leak on error path)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12f6dd860c upstream.
Wolfram Sang pointed out that "efm32,$device" is non-standard. So use the
common scheme and prefix device with "efm32-". The old compatible string
is left in place until arch/arm/boot/dts/efm32* is fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PM callbacks implemented by the spi-atmel driver don't call
spi_master_{resume,suspend}, fix that.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dev_get_drvdata() returns the address of master rather than mcfqspi.
Fixes: af361079 (spi/coldfire-qspi: Drop extra calls to spi_master_get in suspend/resume functions)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Current code set platform drvdata to dspi. However, the code in dspi_suspend()
and dspi_resume() assumes the drvdata is the address of master.
Fix it by setting platform drvdata to master.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The 'ath79_spi_setup_cs' function initializes the chip
select line of a given SPI device in order to make sure
that the device is inactive.
If the SPI_CS_HIGH bit is set for a given device, it
means that the CS line of that device is active HIGH
so it must be set to LOW initially. In case of GPIO
CS lines, the 'ath79_spi_setup_cs' function does the
opposite of that due to the wrong GPIO flags.
Fix the code to use the correct GPIO flags.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Currently, at module removal, one gets the following warnings:
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx])
[<7f02c9cc>] (spi_imx_remove+0x54/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996300 ]---
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:780 clk_disable+0x18/0x24()
Modules linked in: spi_imx(-) [last unloaded: ev76c560]
CPU: 1 PID: 16337 Comm: rmmod Tainted: G W 3.10.17-80548-g90191eb-dirty #33
[<80013b4c>] (unwind_backtrace+0x0/0xf8) from [<800115dc>] (show_stack+0x10/0x14)
[<800115dc>] (show_stack+0x10/0x14) from [<800257b8>] (warn_slowpath_common+0x4c/0x68)
[<800257b8>] (warn_slowpath_common+0x4c/0x68) from [<800257f0>] (warn_slowpath_null+0x1c/0x24)
[<800257f0>] (warn_slowpath_null+0x1c/0x24) from [<803f60ec>] (clk_disable+0x18/0x24)
[<803f60ec>] (clk_disable+0x18/0x24) from [<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx])
[<7f02c9e8>] (spi_imx_remove+0x70/0x9c [spi_imx]) from [<8025868c>] (platform_drv_remove+0x18/0x1c)
[<8025868c>] (platform_drv_remove+0x18/0x1c) from [<80256f60>] (__device_release_driver+0x70/0xcc)
[<80256f60>] (__device_release_driver+0x70/0xcc) from [<80257770>] (driver_detach+0xcc/0xd0)
[<80257770>] (driver_detach+0xcc/0xd0) from [<80256d90>] (bus_remove_driver+0x7c/0xc0)
[<80256d90>] (bus_remove_driver+0x7c/0xc0) from [<80068668>] (SyS_delete_module+0x144/0x1f8)
[<80068668>] (SyS_delete_module+0x144/0x1f8) from [<8000e080>] (ret_fast_syscall+0x0/0x30)
---[ end trace 1f5df9ad54996301 ]---
Since commit 9e556dcc55, "spi: spi-imx: only
enable the clocks when we start to transfer a message", clocks are always
disabled except when transmitting messages. There is thus no need to
disable them at module removal.
Fixes: 9e556dcc55 (spi: spi-imx: only enable the clocks when we start to transfer a message)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
If during registering SPI master due to SPI device probing a SPI transfer
is issued the DMA buffers are not allocated yet.
This fixes the following oops:
pch_spi 0000:02:0c.1: enabling device (0000 -> 0002)
pch_spi 0000:02:0c.1: master is unqueued, this is deprecated
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125aa05>] pch_spi_handle_dma+0x15c/0x6f4
[...]
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
bus_num might be asigned dynamically to e.g. 32766. In this case the
calculated DMA channel based on SPI bus number is bogus. Use SPI channel
number instead for calculation.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Otherwise, spi_setup() fails with unsupported mode bits message.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
As of commit 5ce0ba8865 ("spi: rcar: add
Renesas QSPI support on RSPI") the rspi driver handles Renesas QSPI, too,
but this was not reflected in the Kconfig help text.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
This reverts commit e120cc0dcf.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
master->transfer_one returns positive value is not a error.
So set ret to 0 when master->transfer_one returns positive value.
Otherwise, I hit "spi_master spi0: failed to transfer one message from queue"
error when my transfer_one callback returns 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 543bb25 "spi: add ability to validate xfer->bits_per_word in SPI
core", the driver can set bits_per_word_mask for the master then the SPI core
will reject transfers that attempt to use an unsupported bits_per_word value.
So we can remove the bits_per_word checking in sc18is602_check_transfer() and
let SPI core handle the checking.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation in spi_setup() already set spi->bits_per_word = 8 when
spi->bits_per_word is 0 before calling spi->master->setup.
So we don't need to do it again in setup() callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
