commit 299d0c5b27 upstream.
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison]
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16db8071c upstream.
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d74adbdb9a upstream.
If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the
PEB->LEB mapping.
Caught by Coverity, CID #711212.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eef7d70f7 upstream.
We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.
Coverity CID #1226856
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dad0386b9 upstream.
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68f2981503 upstream.
The torture test should quit once it actually induces an error in the
flash. This step was accidentally removed during refactoring.
Without this fix, the torturetest just continues infinitely, or until
the maximum cycle count is reached. e.g.:
...
[ 7619.218171] mtd_test: error -5 while erasing EB 100
[ 7619.297981] mtd_test: error -5 while erasing EB 100
[ 7619.377953] mtd_test: error -5 while erasing EB 100
[ 7619.457998] mtd_test: error -5 while erasing EB 100
[ 7619.537990] mtd_test: error -5 while erasing EB 100
...
Fixes: 6cf78358c9 ("mtd: mtd_torturetest: use mtd_test helpers")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa5ad3b6eb upstream.
If the erase worker is unable to erase a PEB it will
free the ubi_wl_entry itself.
The failing ubi_wl_entry must not free()'d again after
do_sync_erase() returns.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f38aed975c upstream.
The logic of vfree()'ing vol->upd_buf is tied to vol->updating.
In ubi_start_update() vol->updating is set long before vmalloc()'ing
vol->upd_buf. If we encounter a write failure in ubi_start_update()
before vmalloc() the UBI device release function will try to vfree()
vol->upd_buf because vol->updating is set.
Fix this by allocating vol->upd_buf directly after setting vol->updating.
Fixes:
[ 31.559338] UBI warning: vol_cdev_release: update of volume 2 not finished, volume is damaged
[ 31.559340] ------------[ cut here ]------------
[ 31.559343] WARNING: CPU: 1 PID: 2747 at mm/vmalloc.c:1446 __vunmap+0xe3/0x110()
[ 31.559344] Trying to vfree() nonexistent vm area (ffffc90001f2b000)
[ 31.559345] Modules linked in:
[ 31.565620] 0000000000000bba ffff88002a0cbdb0 ffffffff818f0497 ffff88003b9ba148
[ 31.566347] ffff88002a0cbde0 ffffffff8156f515 ffff88003b9ba148 0000000000000bba
[ 31.567073] 0000000000000000 0000000000000000 ffff88002a0cbe88 ffffffff8156c10a
[ 31.567793] Call Trace:
[ 31.568034] [<ffffffff818f0497>] dump_stack+0x4e/0x7a
[ 31.568510] [<ffffffff8156f515>] ubi_io_write_vid_hdr+0x155/0x160
[ 31.569084] [<ffffffff8156c10a>] ubi_eba_write_leb+0x23a/0x870
[ 31.569628] [<ffffffff81569b36>] vol_cdev_write+0x226/0x380
[ 31.570155] [<ffffffff81179265>] vfs_write+0xb5/0x1f0
[ 31.570627] [<ffffffff81179f8a>] SyS_pwrite64+0x6a/0xa0
[ 31.571123] [<ffffffff818fde12>] system_call_fastpath+0x16/0x1b
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bf1890e86 upstream.
I ran into this error after a ubiupdatevol, because I forgot to backport
e9110361a9 UBI: fix the volumes tree sorting criteria.
UBI error: process_pool_aeb: orphaned volume in fastmap pool
UBI error: ubi_scan_fastmap: Attach by fastmap failed, doing a full scan!
kmem_cache_destroy ubi_ainf_peb_slab: Slab cache still has objects
CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.18-00053-gf05cac8dbf85 #1
[<c000d298>] (unwind_backtrace) from [<c000baa8>] (show_stack+0x10/0x14)
[<c000baa8>] (show_stack) from [<c01b7a68>] (destroy_ai+0x230/0x244)
[<c01b7a68>] (destroy_ai) from [<c01b8fd4>] (ubi_attach+0x98/0x1ec)
[<c01b8fd4>] (ubi_attach) from [<c01ade90>] (ubi_attach_mtd_dev+0x2b8/0x868)
[<c01ade90>] (ubi_attach_mtd_dev) from [<c038b510>] (ubi_init+0x1dc/0x2ac)
[<c038b510>] (ubi_init) from [<c0008860>] (do_one_initcall+0x94/0x140)
[<c0008860>] (do_one_initcall) from [<c037aadc>] (kernel_init_freeable+0xe8/0x1b0)
[<c037aadc>] (kernel_init_freeable) from [<c02730ac>] (kernel_init+0x8/0xe4)
[<c02730ac>] (kernel_init) from [<c00093f0>] (ret_from_fork+0x14/0x24)
UBI: scanning is finished
Freeing the cache in the error path fixes the Slab error.
Tested on at91sam9g35 (3.14.18+fastmap backports)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40ddbf5069 upstream.
commit 65b97cf6b8 introduced in v3.7 caused a regression
by using a reversed CS_MASK thus causing omap_calculate_ecc to
always fail. As the NAND base driver never checks for .calculate()'s
return value, the zeroed ECC values are used as is without showing
any error to the user. However, this won't work and the NAND device
won't be guarded by any error code.
Fix the issue by using the correct mask.
Code was tested on omap3beagle using the following procedure
- flash the primary bootloader (MLO) from the kernel to the first
NAND partition using nandwrite.
- boot the board from NAND. This utilizes OMAP ROM loader that
relies on 1-bit Hamming code ECC.
Fixes: 65b97cf6b8 (mtd: nand: omap2: handle nand on gpmc)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a152056c91 upstream.
I got the following panic on my fsl p5020ds board.
Unable to handle kernel paging request for data at address 0x7375627379737465
Faulting instruction address: 0xc000000000100778
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=24 CoreNet Generic
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-next-20140613 #145
task: c0000000fe080000 ti: c0000000fe088000 task.ti: c0000000fe088000
NIP: c000000000100778 LR: c00000000010073c CTR: 0000000000000000
REGS: c0000000fe08aa00 TRAP: 0300 Not tainted (3.15.0-next-20140613)
MSR: 0000000080029000 <CE,EE,ME> CR: 24ad2e24 XER: 00000000
DEAR: 7375627379737465 ESR: 0000000000000000 SOFTE: 1
GPR00: c0000000000c99b0 c0000000fe08ac80 c0000000009598e0 c0000000fe001d80
GPR04: 00000000000000d0 0000000000000913 c000000007902b20 0000000000000000
GPR08: c0000000feaae888 0000000000000000 0000000007091000 0000000000200200
GPR12: 0000000028ad2e28 c00000000fff4000 c0000000007abe08 0000000000000000
GPR16: c0000000007ab160 c0000000007aaf98 c00000000060ba68 c0000000007abda8
GPR20: c0000000007abde8 c0000000feaea6f8 c0000000feaea708 c0000000007abd10
GPR24: c000000000989370 c0000000008c6228 00000000000041ed c0000000fe00a400
GPR28: c00000000017c1cc 00000000000000d0 7375627379737465 c0000000fe001d80
NIP [c000000000100778] .__kmalloc_track_caller+0x70/0x168
LR [c00000000010073c] .__kmalloc_track_caller+0x34/0x168
Call Trace:
[c0000000fe08ac80] [c00000000087e6b8] uevent_sock_list+0x0/0x10 (unreliable)
[c0000000fe08ad20] [c0000000000c99b0] .kstrdup+0x44/0x90
[c0000000fe08adc0] [c00000000017c1cc] .__kernfs_new_node+0x4c/0x130
[c0000000fe08ae70] [c00000000017d7e4] .kernfs_new_node+0x2c/0x64
[c0000000fe08aef0] [c00000000017db00] .kernfs_create_dir_ns+0x34/0xc8
[c0000000fe08af80] [c00000000018067c] .sysfs_create_dir_ns+0x58/0xcc
[c0000000fe08b010] [c0000000002c711c] .kobject_add_internal+0xc8/0x384
[c0000000fe08b0b0] [c0000000002c7644] .kobject_add+0x64/0xc8
[c0000000fe08b140] [c000000000355ebc] .device_add+0x11c/0x654
[c0000000fe08b200] [c0000000002b5988] .add_disk+0x20c/0x4b4
[c0000000fe08b2c0] [c0000000003a21d4] .add_mtd_blktrans_dev+0x340/0x514
[c0000000fe08b350] [c0000000003a3410] .mtdblock_add_mtd+0x74/0xb4
[c0000000fe08b3e0] [c0000000003a32cc] .blktrans_notify_add+0x64/0x94
[c0000000fe08b470] [c00000000039b5b4] .add_mtd_device+0x1d4/0x368
[c0000000fe08b520] [c00000000039b830] .mtd_device_parse_register+0xe8/0x104
[c0000000fe08b5c0] [c0000000003b8408] .of_flash_probe+0x72c/0x734
[c0000000fe08b750] [c00000000035ba40] .platform_drv_probe+0x38/0x84
[c0000000fe08b7d0] [c0000000003599a4] .really_probe+0xa4/0x29c
[c0000000fe08b870] [c000000000359d3c] .__driver_attach+0x100/0x104
[c0000000fe08b900] [c00000000035746c] .bus_for_each_dev+0x84/0xe4
[c0000000fe08b9a0] [c0000000003593c0] .driver_attach+0x24/0x38
[c0000000fe08ba10] [c000000000358f24] .bus_add_driver+0x1c8/0x2ac
[c0000000fe08bab0] [c00000000035a3a4] .driver_register+0x8c/0x158
[c0000000fe08bb30] [c00000000035b9f4] .__platform_driver_register+0x6c/0x80
[c0000000fe08bba0] [c00000000084e080] .of_flash_driver_init+0x1c/0x30
[c0000000fe08bc10] [c000000000001864] .do_one_initcall+0xbc/0x238
[c0000000fe08bd00] [c00000000082cdc0] .kernel_init_freeable+0x188/0x268
[c0000000fe08bdb0] [c0000000000020a0] .kernel_init+0x1c/0xf7c
[c0000000fe08be30] [c000000000000884] .ret_from_kernel_thread+0x58/0xd4
Instruction dump:
41bd0010 480000c8 4bf04eb5 60000000 e94d0028 e93f0000 7cc95214 e8a60008
7fc9502a 2fbe0000 419e00c8 e93f0022 <7f7e482a> 39200000 88ed06b2 992d06b2
---[ end trace b4c9a94804a42d40 ]---
It seems that the corrupted partition header on my mtd device triggers
a bug in the ftl. In function build_maps() it will allocate the buffers
needed by the mtd partition, but if something goes wrong such as kmalloc
failure, mtd read error or invalid partition header parameter, it will
free all allocated buffers and then return non-zero. In my case, it
seems that partition header parameter 'NumTransferUnits' is invalid.
And the ftl_freepart() is a function which free all the partition
buffers allocated by build_maps(). Given the build_maps() is a self
cleaning function, so there is no need to invoke this function even
if build_maps() return with error. Otherwise it will causes the
buffers to be freed twice and then weird things would happen.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6938ad40cb upstream.
These two function's switch case lack the 'break' that make them always
return error.
Signed-off-by: Ted Juan <ted.juan@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7e460624f upstream.
The pxa3xx_nand driver currently uses __raw_writel() and __raw_readl()
to access I/O registers. However, those functions do not do any
endianness swapping, which means that they won't work when the CPU
runs in big-endian but the I/O registers are little endian, which is
the common situation for ARM systems running big endian.
Since __raw_writel() and __raw_readl() do not include any memory
barriers and the pxa3xx_nand driver can only be compiled for ARM
platforms, the closest I/o accessors functions that do endianess
swapping are writel_relaxed() and readl_relaxed().
This patch has been verified to work on Armada XP GP: without the
patch, the NAND is not detected when the kernel runs big endian while
it is properly detected when the kernel runs little endian. With the
patch applied, the NAND is properly detected in both situations
(little and big endian).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f306e8c3b6 upstream.
fixes: commit 62116e5171
mtd: nand: omap2: Support for hardware BCH error correction.
In omap_elm_correct_data(), if bitflip_count in an erased-page is within the
correctable limit (< ecc.strength), then it is not indicated back to the caller
ecc->read_page().
This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as
perfectly clean and use it for writing even if actual bitflip_count was
dangerously high (bitflip_count > mtd->bitflip_threshold).
This patch fixes this above issue, by returning 'stats' to caller
ecc->read_page() under all scenarios.
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f034d87def upstream.
As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc
causes a crash if the driver did not register ecc->hwctl or ecc->calculate.
This behavior was introduced in
commit 837a6ba4f3
"mtd: nand: subpage write support for hardware based ECC schemes".
This fixes a crash by emulating subpage write support by padding sub-page data
with 0xff on either sides to make it full page compatible.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4c2330577 upstream.
We always put a NUL terminator one space past the end of the "vendor"
buffer. Walter Harms also pointed out that this should just use
kstrndup().
Fixes: 7d17c02a01 ('mtd: Add new SmartMedia/xD FTL')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c69dbbf333 upstream.
Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.
Fixes: 8bff82cbc3 ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86e4bbc766 upstream.
Passing a name to request_mem_region() isn't optional and can't just
be NULL. Passing NULL causes a NULL ptr deref later in the boot
process.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90445ff624 upstream.
Crash detected on sam5d35 and its pmecc nand ecc controller.
The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.
Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
touch freed memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J2Up
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.14-rc5' of git://git.infradead.org/linux-ubifs
Pull ubifs fix from Artem Bityutskiy:
"Just a single fix for the UBI module unload path which makes sure we
do not touch freed memory"
* tag 'upstream-3.14-rc5' of git://git.infradead.org/linux-ubifs:
UBI: fix some use after free bugs
This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.
CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) In current implementation, ecclayout->oobfree->offset is calculated with
respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
be stored contiguously in OOB.
So, this patch calculates ecclayout->oobfree->offset with respect to last
ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.
2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
which should not be over-written by any file-system metadata.
So this patch aligns oobfree->offset taking into account of such markers.
CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move the kmem_cache_free() calls down a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
possible, because the eraseblock may be in an "unstable" state and write
operation sometimes causes NOR chip lock-ups.
* Both UBI and UBIFS changes are now maintainer in one single tree, because the
amount of changes dropped significantly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=pRDO
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.14-rc1' of git://git.infradead.org/linux-ubifs
Pull ubifs updates from Artem Bityutskiy:
- Improve the NOR erasure quirk - now it tries to do as little writes
as possible, because the eraseblock may be in an "unstable" state and
write operation sometimes causes NOR chip lock-ups.
- Both UBI and UBIFS changes are now maintainer in one single tree,
because the amount of changes dropped significantly.
* tag 'upstream-3.14-rc1' of git://git.infradead.org/linux-ubifs:
UBI: avoid program operation on NOR flash after erasure interrupted
MAINTAINERS: keep UBI and UBIFS stuff in the same tree
UBI: fix error return code
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
- Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
David's "ack" for this; I'm sure he approves, but he's been pretty silent
lately)
- Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
- Last (?) round of pxa3xx improvements for supporting Armada 370/XP
- Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
- Quad read mode support for SPI NOR driver (m25p80)
- Update Davinci NAND driver to prepare for use on new platforms
- Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
- Miscellaneous NAND device support (new IDs)
- Add READ RETRY support for Micron MLC NAND
- Support new GPMI NAND ECC layout device-tree binding
- Avoid mapping stack/vmalloc() memory for GPMI NAND DMA
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=3nT9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
David's "ack" for this; I'm sure he approves, but he's been pretty silent
lately)
- Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
- Last (?) round of pxa3xx improvements for supporting Armada 370/XP
- Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
- Quad read mode support for SPI NOR driver (m25p80)
- Update Davinci NAND driver to prepare for use on new platforms
- Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
- Miscellaneous NAND device support (new IDs)
- Add READ RETRY support for Micron MLC NAND
- Support new GPMI NAND ECC layout device-tree binding
- Avoid mapping stack/vmalloc() memory for GPMI NAND DMA
* tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd: (151 commits)
mtd: gpmi: add sanity check when mapping DMA for read_buf/write_buf
mtd: gpmi: allocate a proper buffer for non ECC read/write
mtd: m25p80: Set rx_nbits for Quad SPI transfers
mtd: m25p80: Enable Quad SPI read transfers for s25fl512s
mtd: s3c2410: Merge plat/regs-nand.h into s3c2410.c
mtd: mtdram: add missing 'const'
mtd: m25p80: assign default read command
mtd: nuc900_nand: remove redundant return value check of platform_get_resource()
mtd: plat_nand: remove redundant return value check of platform_get_resource()
mtd: nand: add Intel manufacturer ID
mtd: nand: add SanDisk manufacturer ID
mtd: nand: add support for Samsung K9LCG08U0B
mtd: nand: pxa3xx: Add support for 2048 bytes page size devices
mtd: m25p80: Use OPCODE_QUAD_READ_4B for 4-byte addressing
mtd: nand: don't use {read,write}_buf for 8-bit transfers
mtd: nand: use __packed shorthand
mtd: nand: support Micron READ RETRY
mtd: nand: add generic READ RETRY support
mtd: nand: add ONFI vendor block for Micron
mtd: nand: localize ECC failures per page
...
The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..
This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The @data_buffer_dma buffer is used for non ECC read/write.
Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.
The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.
This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.
While an earlier version of commit 3487a63955
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtdram_init_device() wasn't updated along with mtd_partition.name.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
In the following commit (in -next):
commit 8552b439ab
drivers: mtd: m25p80: convert "bool" read check into an enum
We converted the boolean 'fast_read' property to become an enum
'flash_read', but at the same time, we changed the conditional path so
that it doesn't choose a default value in some cases (technically, we
choose the correct default simply by virtue of devm_kzalloc(), which
zeroes this out to be a NORMAL read operation, but still...).
Fix this by setting a default for the 'else' clause.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource(). And move those two call together
to make the connection between them more clear.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Assume that:
tmp = ((extid >> 2) & 0x04) | (extid & 0x03));
From the K9LCG08U0B's datasheet, we know that:
the oob size is 640 when tmp is 6;
the oob size is 1024 when tmp is 7;
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: fixed compile issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support for devices with 2048B page sizes and
4-bit ECC strength requirements. This is achieved by enabling the BCH
ECC engine, which provides a higher strength: 16-bit over 2048 bytes.
Additionally, add a proper ECC layout to model the controller's view
of the device (where 'U' means unused and 'B' is the bad block marker):
----------------------------------------------------
| 2048B data | B | B | 30B spare | 30B ECC | U | U |
----------------------------------------------------
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[Brian: updated with Ezequiel's patch description]
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 3487a63955 ("drivers: mtd: m25p80: add
quad read support") in -next added both the 3-byte OPCODE_QUAD_READ and the
4-byte OPCODE_QUAD_READ_4B, but incorrectly uses OPCODE_QUAD_READ for both
3-byte and 4-byte addressing.
Use OPCODE_QUAD_READ_4B in the 4-byte case to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the Open NAND Flash Interface Specification (ONFI) Revision
3.1 "Parameters are always transferred on the lower 8-bits of the data
bus." for the Get Features and Set Features commands.
So using read_buf and write_buf is wrong for 16-bit wide nand chips as
they use I/O[15:0]. The Get Features command is easily fixed using 4
times the read_byte callback. For Set Features implement a new
overwritable callback "write_byte". Still I expect the default to work
just fine for all controllers and making it overwriteable was just done
for symmetry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Brian: fixed warning]
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron provides READ RETRY support via the ONFI vendor-specific
parameter block (to indicate how many read-retry modes are available)
and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature
address (to support reading/switching the current read-retry mode).
The recommended sequence is as follows:
1. Perform PAGE_READ operation
2. If no ECC error, we are done
3. Run SET_FEATURES with feature address 89h, mode 1
4. Retry PAGE_READ operation
5. If ECC error and there are remaining supported modes, increment the
mode and return to step 3. Otherwise, this is a true ECC error.
6. Run SET_FEATURES with feature address 89h, mode 0, to return to the
default state.
This patch implements the chip->setup_read_retry() callback for
Micron and fills in the chip->read_retries.
Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes.
The Micron vendor-specific table was checked against the datasheets for
the following Micron NAND:
Needs retry Cell-type Part number Vendor revision Byte 180
----------- --------- ---------------- --------------- ------------
No SLC MT29F16G08ABABA 1 Reserved (0)
No MLC MT29F32G08CBABA 1 Reserved (0)
No SLC MT29F1G08AACWP 1 0
Yes MLC MT29F32G08CBADA 1 08h
Yes MLC MT29F64G08CBABA 2 08h
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Modern MLC (and even SLC?) NAND can experience a large number of
bitflips (beyond the recommended correctability capacity) due to drifts
in the voltage threshold (Vt). These bitflips can cause ECC errors to
occur well within the expected lifetime of the flash. To account for
this, some manufacturers provide a mechanism for shifting the Vt
threshold after a corrupted read.
The generic pattern seems to be that a particular flash has N read retry
modes (where N = 0, traditionally), and after an ECC failure, the host
should reconfigure the flash to use the next available mode, then retry
the read operation. This process repeats until all bitfips can be
corrected or until the host has tried all available retry modes.
This patch adds the infrastructure support for a
vendor-specific/flash-specific callback, used for setting the read-retry
mode (i.e., voltage threshold).
For now, this patch always returns the flash to mode 0 (the default
mode) after a successful read-retry, according to the flowchart found in
Micron's datasheets. This may need to change in the future if it is
determined that eventually, mode 0 is insufficient for the majority of
the flash cells (and so for performance reasons, we should leave the
flash in mode 1, 2, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
ECC failures can be tracked at the page level, not the do_read_ops level
(i.e., a potentially multi-page transaction).
This helps prepare for READ RETRY support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Now that the driver can support the Armada 370/XP SoC NAND controller,
add the devicetree compatible string, enabling its use.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
