commit adf9a3ab90 upstream.
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cddc9434e3 upstream.
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ea6db90e75 upstream.
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5a07975ad0 upstream.
The driver can be crashed with devices that expose crafted descriptors
with too few endpoints.
See: http://seclists.org/bugtraq/2016/Mar/61
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: fix OOB endpoint check and add error messages ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4e9a0b0525 upstream.
An attack using the lack of sanity checking in probe is known. This
patch checks for the existence of a second port.
CVE-2016-3136
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: add error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6490865c67 upstream.
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 55ff8cfbc4 upstream.
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: add definition of MAX_CMNDS from upstream commit
5e61aede47 ("uas: Do not use scsi_host_find_tag")]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0b818e3956 upstream.
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0d5ce778c4 upstream.
A typo of j for i led to a logic bug. To rule out future
confusion, the variable names are made meaningful.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 264904ccc3 upstream.
Some devices I got show an inability to operate right after
power on if they are already connected. They are beyond recovery
if the descriptors are requested multiple times. So in case of
a timeout we rather bail early and reset again. But it must be
done only on the first loop lest we get into a reset/time out
spiral that can be overcome with a retry.
This patch is a rework of a patch that fell through the cracks.
http://www.spinics.net/lists/linux-usb/msg103263.html
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8835ba4a39 upstream.
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4ec0ef3a82 upstream.
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 04fdbc825f upstream.
The MC74xx and EM74xx modules use different IDs by default, according
to the Lenovo EM7455 driver for Windows.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5deef5551c upstream.
This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3c4c615d70 upstream.
The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 6627ae1938 upstream.
Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c450960187 upstream.
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda61871 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda61871 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5c82171167 upstream.
xhci driver frees data for all devices, both usb2 and and usb3 the
first time usb_remove_hcd() is called, including td_list and and xhci_ring
structures.
When usb_remove_hcd() is called a second time for the second xhci bus it
will try to dequeue all pending urbs, and touches td_list which is already
freed for that endpoint.
Reported-by: Joe Lawrence <joe.lawrence@stratus.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ccc04afb72 upstream.
Intel Broxton M was verifed to require XHCI_PME_STUCK_QUIRK quirk as well.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit a683509071 upstream.
This reverts commit e210c422b6 ("xhci: don't finish a TD if we get a
short transfer event mid TD")
Turns out that most host controllers do not follow the xHCI specs and never
send the second event for the last TRB in the TD if there was a short event
mid-TD.
Returning the URB directly after the first short-transfer event is far
better than never returning the URB. (class drivers usually timeout
after 30sec). For the hosts that do send the second event we will go
back to treating it as misplaced event and print an error message for it.
The origial patch was sent to stable kernels and needs to be reverted from
there as well
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e03cdf22a2 upstream.
Harald Linden reports that the ftdi_sio driver works properly for the
Yaesu SCU-18 cable if the device ids are added to the driver. So let's
add them.
Reported-by: Harald Linden <harald.linden@7183.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ff4e2494dc upstream.
This patch adds support for two PIDs of LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cac9b50b0d upstream.
Fix null-pointer dereference at probe should a (malicious) Treo device
lack the expected endpoints.
Specifically, the Treo port-setup hack was dereferencing the bulk-in and
interrupt-in urbs without first making sure they had been allocated by
core.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f487c54ddd upstream.
Added the USB serial console device ID for IAI Corp. RCB-CV-USB
USB to RS485 adaptor.
Signed-off-by: Peter Dedecker <peter.dedecker@hotmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d8f00cd685 upstream.
In function usb_reset_and_verify_device, the old BOS descriptor may
still be used before allocating a new one. (usb_unlocked_disable_lpm
function uses it under the situation that it fails to disable lpm.)
So we cannot set the udev->bos to NULL before that, just keep what it
was. It will be overwrite when allocating a new one.
Crash log:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000010
IP: [<ffffffff8171f98d>] usb_enable_link_state+0x2d/0x2f0
Call Trace:
[<ffffffff8171ed5b>] ? usb_set_lpm_timeout+0x12b/0x140
[<ffffffff8171fcd1>] usb_enable_lpm+0x81/0xa0
[<ffffffff8171fdd8>] usb_disable_lpm+0xa8/0xc0
[<ffffffff8171fe1c>] usb_unlocked_disable_lpm+0x2c/0x50
[<ffffffff81723933>] usb_reset_and_verify_device+0xc3/0x710
[<ffffffff8172c4ed>] ? usb_sg_wait+0x13d/0x190
[<ffffffff81724743>] usb_reset_device+0x133/0x280
[<ffffffff8179ccd1>] usb_stor_port_reset+0x61/0x70
[<ffffffff8179cd68>] usb_stor_invoke_transport+0x88/0x520
Signed-off-by: Du, Changbin <changbin.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e912e685f3 upstream.
This phone needs to be handled by a specialised firmware tool
and is reported to crash irrevocably if cdc-acm takes it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ffdb1e369a upstream.
For Intel 7260 modem, it is needed for host side to send zero
packet if the BULK OUT size is equal to USB endpoint max packet
length. Otherwise, modem side may still wait for more data and
cannot give response to host side.
Signed-off-by: Konrad Leszczynski <konrad.leszczynski@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 19454462ac upstream.
In current acm driver, the bulk-in callback function ignores the
URBs unlinked in usb core.
This causes unexpected data loss in some cases. For example,
runtime suspend entry will unlinked all urbs and set urb->status
to -ENOENT even those urbs might have data not processed yet.
Hence, data loss occurs.
This patch lets bulk-in callback function handle unlinked urbs
to avoid data loss.
Signed-off-by: Tang Jian Qiang <jianqiang.tang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16:
- use 'urb->status' instead of local variable 'status'
- adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit cb3232138e upstream.
The visor driver crashes in clie_5_attach() when a specially crafted USB
device without bulk-out endpoint is detected. This fix adds a check that
the device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Fixes: cfb8da8f69 ("USB: visor: fix initialisation of UX50/TH55 devices")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Moritz Muehlenhoff <jmm@inutil.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f7d7f59ab1 upstream.
Add the USB device ID for ELV Marble Sound Board 1.
Signed-off-by: Oliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1eaf35e4dd upstream.
The module should fail to load.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16:
- moved usb_disabled() check to the top of the function so that there's
no need to invoke xhci_unregister_pci() before returning. Suggested
by gregkh. ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e50293ef97 upstream.
Commit 8520f38099 ("USB: change hub initialization sleeps to
delayed_work") changed the hub_activate() routine to make part of it
run in a workqueue. However, the commit failed to take a reference to
the usb_hub structure or to lock the hub interface while doing so. As
a result, if a hub is plugged in and quickly unplugged before the work
routine can run, the routine will try to access memory that has been
deallocated. Or, if the hub is unplugged while the routine is
running, the memory may be deallocated while it is in active use.
This patch fixes the problem by taking a reference to the usb_hub at
the start of hub_activate() and releasing it at the end (when the work
is finished), and by locking the hub interface while the work routine
is running. It also adds a check at the start of the routine to see
if the hub has already been disconnected, in which nothing should be
done.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Alexandru Cornea <alexandru.cornea@intel.com>
Tested-by: Alexandru Cornea <alexandru.cornea@intel.com>
Fixes: 8520f38099 ("USB: change hub initialization sleeps to delayed_work")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16:
- Added forward declaration of hub_release() which mainline had with commit
32a6958998 ("usb: hub: convert khubd into workqueue") ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit abdc9a3b4b upstream.
The code expects the loop to end with "retries" set to zero but, because
it is a post-op, it will end set to -1. I have fixed this by moving the
decrement inside the loop.
Fixes: 014aa2a3c3 ('USB: ipaq: minor ipaq_open() cleanup.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 183e53e8dd upstream.
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c68 ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ad87e03213 upstream.
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f69115fdbc upstream.
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 096b110a3d upstream.
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 5377adb092 upstream.
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f9fa1887dc upstream.
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 464ad8c43a upstream.
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9fa62b1a31 upstream.
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
