commit 93d17397e4 upstream.
It turns out that if the guest does a H_CEDE while the CPU is in
a transactional state, and the H_CEDE does a nap, and the nap
loses the architected state of the CPU (which is is allowed to do),
then we lose the checkpointed state of the virtual CPU. In addition,
the transactional-memory state recorded in the MSR gets reset back
to non-transactional, and when we try to return to the guest, we take
a TM bad thing type of program interrupt because we are trying to
transition from non-transactional to transactional with a hrfid
instruction, which is not permitted.
The result of the program interrupt occurring at that point is that
the host CPU will hang in an infinite loop with interrupts disabled.
Thus this is a denial of service vulnerability in the host which can
be triggered by any guest (and depending on the guest kernel, it can
potentially triggered by unprivileged userspace in the guest).
This vulnerability has been assigned the ID CVE-2016-5412.
To fix this, we save the TM state before napping and restore it
on exit from the nap, when handling a H_CEDE in real mode. The
case where H_CEDE exits to host virtual mode is already OK (as are
other hcalls which exit to host virtual mode) because the exit
path saves the TM state.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f024ee0984 upstream.
This moves the transactional memory state save and restore sequences
out of the guest entry/exit paths into separate procedures. This is
so that these sequences can be used in going into and out of nap
in a subsequent patch.
The only code changes here are (a) saving and restore LR on the
stack, since these new procedures get called with a bl instruction,
(b) explicitly saving r1 into the PACA instead of assuming that
HSTATE_HOST_R1(r13) is already set, and (c) removing an unnecessary
and redundant setting of MSR[TM] that should have been removed by
commit 9d4d0bdd9e0a ("KVM: PPC: Book3S HV: Add transactional memory
support", 2013-09-24) but wasn't.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
[bwh: Backported to 3.16: include dots in subroutine names]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1ead852dd8 upstream.
Fix boot crash that triggers if this driver is built into a kernel and
run on non-AMD systems.
AMD northbridges users call amd_cache_northbridges() and it returns
a negative value to signal that we weren't able to cache/detect any
northbridges on the system.
At least, it should do so as all its callers expect it to do so. But it
does return a negative value only when kmalloc() fails.
Fix it to return -ENODEV if there are no NBs cached as otherwise, amd_nb
users like amd64_edac, for example, which relies on it to know whether
it should load or not, gets loaded on systems like Intel Xeons where it
shouldn't.
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1466097230-5333-2-git-send-email-bp@alien8.de
Link: https://lkml.kernel.org/r/5761BEB0.9000807@cybernetics.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 65c0554b73 upstream.
Logan Gunthorpe reports that hibernation stopped working reliably for
him after commit ab76f7b4ab (x86/mm: Set NX on gap between __ex_table
and rodata).
That turns out to be a consequence of a long-standing issue with the
64-bit image restoration code on x86, which is that the temporary
page tables set up by it to avoid page tables corruption when the
last bits of the image kernel's memory contents are copied into
their original page frames re-use the boot kernel's text mapping,
but that mapping may very well get corrupted just like any other
part of the page tables. Of course, if that happens, the final
jump to the image kernel's entry point will go to nowhere.
The exact reason why commit ab76f7b4ab matters here is that it
sometimes causes a PMD of a large page to be split into PTEs
that are allocated dynamically and get corrupted during image
restoration as described above.
To fix that issue note that the code copying the last bits of the
image kernel's memory contents to the page frames occupied by them
previoulsy doesn't use the kernel text mapping, because it runs from
a special page covered by the identity mapping set up for that code
from scratch. Hence, the kernel text mapping is only needed before
that code starts to run and then it will only be used just for the
final jump to the image kernel's entry point.
Accordingly, the temporary page tables set up in swsusp_arch_resume()
on x86-64 need to contain the kernel text mapping too. That mapping
is only going to be used for the final jump to the image kernel, so
it only needs to cover the image kernel's entry point, because the
first thing the image kernel does after getting control back is to
switch over to its own original page tables. Moreover, the virtual
address of the image kernel's entry point in that mapping has to be
the same as the one mapped by the image kernel's page tables.
With that in mind, modify the x86-64's arch_hibernation_header_save()
and arch_hibernation_header_restore() routines to pass the physical
address of the image kernel's entry point (in addition to its virtual
address) to the boot kernel (a small piece of assembly code involved
in passing the entry point's virtual address to the image kernel is
not necessary any more after that, so drop it). Update RESTORE_MAGIC
too to reflect the image header format change.
Next, in set_up_temporary_mappings(), use the physical and virtual
addresses of the image kernel's entry point passed in the image
header to set up a minimum kernel text mapping (using memory pages
that won't be overwritten by the image kernel's memory contents) that
will map those addresses to each other as appropriate.
This makes the concern about the possible corruption of the original
boot kernel text mapping go away and if the the minimum kernel text
mapping used for the final jump marks the image kernel's entry point
memory as executable, the jump to it is guaraneed to succeed.
Fixes: ab76f7b4ab (x86/mm: Set NX on gap between __ex_table and rodata)
Link: http://marc.info/?l=linux-pm&m=146372852823760&w=2
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 190ce8693c upstream.
Currently we have 2 segments that are bolted for the kernel linear
mapping (ie 0xc000... addresses). This is 0 to 1TB and also the kernel
stacks. Anything accessed outside of these regions may need to be
faulted in. (In practice machines with TM always have 1T segments)
If a machine has < 2TB of memory we never fault on the kernel linear
mapping as these two segments cover all physical memory. If a machine
has > 2TB of memory, there may be structures outside of these two
segments that need to be faulted in. This faulting can occur when
running as a guest as the hypervisor may remove any SLB that's not
bolted.
When we treclaim and trecheckpoint we have a window where we need to
run with the userspace GPRs. This means that we no longer have a valid
stack pointer in r1. For this window we therefore clear MSR RI to
indicate that any exceptions taken at this point won't be able to be
handled. This means that we can't take segment misses in this RI=0
window.
In this RI=0 region, we currently access the thread_struct for the
process being context switched to or from. This thread_struct access
may cause a segment fault since it's not guaranteed to be covered by
the two bolted segment entries described above.
We've seen this with a crash when running as a guest with > 2TB of
memory on PowerVM:
Unrecoverable exception 4100 at c00000000004f138
Oops: Unrecoverable exception, sig: 6 [#1]
SMP NR_CPUS=2048 NUMA pSeries
CPU: 1280 PID: 7755 Comm: kworker/1280:1 Tainted: G X 4.4.13-46-default #1
task: c000189001df4210 ti: c000189001d5c000 task.ti: c000189001d5c000
NIP: c00000000004f138 LR: 0000000010003a24 CTR: 0000000010001b20
REGS: c000189001d5f730 TRAP: 4100 Tainted: G X (4.4.13-46-default)
MSR: 8000000100001031 <SF,ME,IR,DR,LE> CR: 24000048 XER: 00000000
CFAR: c00000000004ed18 SOFTE: 0
GPR00: ffffffffc58d7b60 c000189001d5f9b0 00000000100d7d00 000000003a738288
GPR04: 0000000000002781 0000000000000006 0000000000000000 c0000d1f4d889620
GPR08: 000000000000c350 00000000000008ab 00000000000008ab 00000000100d7af0
GPR12: 00000000100d7ae8 00003ffe787e67a0 0000000000000000 0000000000000211
GPR16: 0000000010001b20 0000000000000000 0000000000800000 00003ffe787df110
GPR20: 0000000000000001 00000000100d1e10 0000000000000000 00003ffe787df050
GPR24: 0000000000000003 0000000000010000 0000000000000000 00003fffe79e2e30
GPR28: 00003fffe79e2e68 00000000003d0f00 00003ffe787e67a0 00003ffe787de680
NIP [c00000000004f138] restore_gprs+0xd0/0x16c
LR [0000000010003a24] 0x10003a24
Call Trace:
[c000189001d5f9b0] [c000189001d5f9f0] 0xc000189001d5f9f0 (unreliable)
[c000189001d5fb90] [c00000000001583c] tm_recheckpoint+0x6c/0xa0
[c000189001d5fbd0] [c000000000015c40] __switch_to+0x2c0/0x350
[c000189001d5fc30] [c0000000007e647c] __schedule+0x32c/0x9c0
[c000189001d5fcb0] [c0000000007e6b58] schedule+0x48/0xc0
[c000189001d5fce0] [c0000000000deabc] worker_thread+0x22c/0x5b0
[c000189001d5fd80] [c0000000000e7000] kthread+0x110/0x130
[c000189001d5fe30] [c000000000009538] ret_from_kernel_thread+0x5c/0xa4
Instruction dump:
7cb103a6 7cc0e3a6 7ca222a6 78a58402 38c00800 7cc62838 08860000 7cc000a6
38a00006 78c60022 7cc62838 0b060000 <e8c701a0> 7ccff120 e8270078 e8a70098
---[ end trace 602126d0a1dedd54 ]---
This fixes this by copying the required data from the thread_struct to
the stack before we clear MSR RI. Then once we clear RI, we only access
the stack, guaranteeing there's no segment miss.
We also tighten the region over which we set RI=0 on the treclaim()
path. This may have a slight performance impact since we're adding an
mtmsr instruction.
Fixes: 090b9284d7 ("powerpc/tm: Clear MSR RI in non-recoverable TM code")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bcf4dd5f9e upstream.
The test_fp_ctl function is used to test if a given value is a valid
floating-point control. The inline assembly in test_fp_ctl uses an
incorrect constraint for the 'orig_fpc' variable. If the compiler
chooses the same register for 'fpc' and 'orig_fpc' the test_fp_ctl()
function always returns true. This allows user space to trigger
kernel oopses with invalid floating-point control values on the
signal stack.
This problem has been introduced with git commit 4725c86055
"s390: fix save and restore of the floating-point-control register"
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9bd54517ee upstream.
If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core()
gets called following message gets printed in debug console:
----------------->8---------------
CONFIG_ARC_DW2_UNWIND needs to be enabled
----------------->8---------------
That message makes sense if user indeed wants to see a backtrace or
get nice function call-graphs in perf but what if user disabled
unwinder for the purpose? Why pollute his debug console?
So instead we'll warn user about possibly missing feature once and
let him decide if that was what he or she really wanted.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f52e126cc7 upstream.
With recent binutils update to support dwarf CFI pseudo-ops in gas, we
now get .eh_frame vs. .debug_frame. Although the call frame info is
exactly the same in both, the CIE differs, which the current kernel
unwinder can't cope with.
This broke both the kernel unwinder as well as loadable modules (latter
because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in
the module loader)
The ideal solution would be to switch unwinder to .eh_frame.
For now however we can make do by just ensureing .debug_frame is
generated by removing -fasynchronous-unwind-tables
.eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables
.debug_frame generated with -gdwarf-2
Fixes STAR 9001058196
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 591d215afc upstream.
kvm provides kvm_vcpu_uninit(), which amongst other things, releases the
last reference to the struct pid of the task that was last running the vcpu.
On arm64 built with CONFIG_DEBUG_KMEMLEAK, starting a guest with kvmtool,
then killing it with SIGKILL results (after some considerable time) in:
> cat /sys/kernel/debug/kmemleak
> unreferenced object 0xffff80007d5ea080 (size 128):
> comm "lkvm", pid 2025, jiffies 4294942645 (age 1107.776s)
> hex dump (first 32 bytes):
> 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
> backtrace:
> [<ffff8000001b30ec>] create_object+0xfc/0x278
> [<ffff80000071da34>] kmemleak_alloc+0x34/0x70
> [<ffff80000019fa2c>] kmem_cache_alloc+0x16c/0x1d8
> [<ffff8000000d0474>] alloc_pid+0x34/0x4d0
> [<ffff8000000b5674>] copy_process.isra.6+0x79c/0x1338
> [<ffff8000000b633c>] _do_fork+0x74/0x320
> [<ffff8000000b66b0>] SyS_clone+0x18/0x20
> [<ffff800000085cb0>] el0_svc_naked+0x24/0x28
> [<ffffffffffffffff>] 0xffffffffffffffff
On x86 kvm_vcpu_uninit() is called on the path from kvm_arch_destroy_vm(),
on arm no equivalent call is made. Add the call to kvm_arch_vcpu_free().
Signed-off-by: James Morse <james.morse@arm.com>
Fixes: 749cf76c5a ("KVM: ARM: Initial skeleton to compile KVM support")
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8e96a87c54 upstream.
Userspace can quite legitimately perform an exec() syscall with a
suspended transaction. exec() does not return to the old process, rather
it load a new one and starts that, the expectation therefore is that the
new process starts not in a transaction. Currently exec() is not treated
any differently to any other syscall which creates problems.
Firstly it could allow a new process to start with a suspended
transaction for a binary that no longer exists. This means that the
checkpointed state won't be valid and if the suspended transaction were
ever to be resumed and subsequently aborted (a possibility which is
exceedingly likely as exec()ing will likely doom the transaction) the
new process will jump to invalid state.
Secondly the incorrect attempt to keep the transactional state while
still zeroing state for the new process creates at least two TM Bad
Things. The first triggers on the rfid to return to userspace as
start_thread() has given the new process a 'clean' MSR but the suspend
will still be set in the hardware MSR. The second TM Bad Thing triggers
in __switch_to() as the processor is still transactionally suspended but
__switch_to() wants to zero the TM sprs for the new process.
This is an example of the outcome of calling exec() with a suspended
transaction. Note the first 700 is likely the first TM bad thing
decsribed earlier only the kernel can't report it as we've loaded
userspace registers. c000000000009980 is the rfid in
fast_exception_return()
Bad kernel stack pointer 3fffcfa1a370 at c000000000009980
Oops: Bad kernel stack pointer, sig: 6 [#1]
CPU: 0 PID: 2006 Comm: tm-execed Not tainted
NIP: c000000000009980 LR: 0000000000000000 CTR: 0000000000000000
REGS: c00000003ffefd40 TRAP: 0700 Not tainted
MSR: 8000000300201031 <SF,ME,IR,DR,LE,TM[SE]> CR: 00000000 XER: 00000000
CFAR: c0000000000098b4 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 00003fffcfa1a370 0000000000000000 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 00003fff966611c0 0000000000000000 0000000000000000 0000000000000000
NIP [c000000000009980] fast_exception_return+0xb0/0xb8
LR [0000000000000000] (null)
Call Trace:
Instruction dump:
f84d0278 e9a100d8 7c7b03a6 e84101a0 7c4ff120 e8410170 7c5a03a6 e8010070
e8410080 e8610088 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed023b
Kernel BUG at c000000000043e80 [verbose debug info unavailable]
Unexpected TM Bad Thing exception at c000000000043e80 (msr 0x201033)
Oops: Unrecoverable exception, sig: 6 [#2]
CPU: 0 PID: 2006 Comm: tm-execed Tainted: G D
task: c0000000fbea6d80 ti: c00000003ffec000 task.ti: c0000000fb7ec000
NIP: c000000000043e80 LR: c000000000015a24 CTR: 0000000000000000
REGS: c00000003ffef7e0 TRAP: 0700 Tainted: G D
MSR: 8000000300201033 <SF,ME,IR,DR,RI,LE,TM[SE]> CR: 28002828 XER: 00000000
CFAR: c000000000015a20 SOFTE: 0
PACATMSCRATCH: b00000010000d033
GPR00: 0000000000000000 c00000003ffefa60 c000000000db5500 c0000000fbead000
GPR04: 8000000300001033 2222222222222222 2222222222222222 00000000ff160000
GPR08: 0000000000000000 800000010000d033 c0000000fb7e3ea0 c00000000fe00004
GPR12: 0000000000002200 c00000000fe00000 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 c0000000fbea7410 00000000ff160000
GPR24: c0000000ffe1f600 c0000000fbea8700 c0000000fbea8700 c0000000fbead000
GPR28: c000000000e20198 c0000000fbea6d80 c0000000fbeab680 c0000000fbea6d80
NIP [c000000000043e80] tm_restore_sprs+0xc/0x1c
LR [c000000000015a24] __switch_to+0x1f4/0x420
Call Trace:
Instruction dump:
7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8
4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020
This fixes CVE-2016-5828.
Fixes: bc2a9408fa ("powerpc: Hook in new transactional memory code")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 844e3be476 upstream.
Classic BPF JIT was never ported completely to work on little endian
powerpc. However, it can be enabled and will crash the system when used.
As such, disable use of BPF JIT on ppc64le.
Fixes: 7c105b63bd ("powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.")
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.16: config symbol is BPF_JIT and also depends on PPC64]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 20c27a4270 upstream.
__sync_icache_dcache unconditionally skips the cache maintenance for
anonymous pages, under the assumption that flushing is only required in
the presence of D-side aliases [see 7249b79f6b ("arm64: Do not flush
the D-cache for anonymous pages")].
Unfortunately, this breaks migration of anonymous pages holding
self-modifying code, where userspace cannot be reasonably expected to
reissue maintenance instructions in response to a migration.
This patch fixes the problem by removing the broken page_mapping(page)
check from the cache syncing code, otherwise we may end up fetching and
executing stale instructions from the PoU.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8f50b8e574 upstream.
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit dcfc47248d upstream.
Fix kprobe_fault_handler() to clear the TF (trap flag) bit of
the flags register in the case of a fault fixup on single-stepping.
If we put a kprobe on the instruction which caused a
page fault (e.g. actual mov instructions in copy_user_*),
that fault happens on the single-stepping buffer. In this
case, kprobes resets running instance so that the CPU can
retry execution on the original ip address.
However, current code forgets to reset the TF bit. Since this
fault happens with TF bit set for enabling single-stepping,
when it retries, it causes a debug exception and kprobes
can not handle it because it already reset itself.
On the most of x86-64 platform, it can be easily reproduced
by using kprobe tracer. E.g.
# cd /sys/kernel/debug/tracing
# echo p copy_user_enhanced_fast_string+5 > kprobe_events
# echo 1 > events/kprobes/enable
And you'll see a kernel panic on do_debug(), since the debug
trap is not handled by kprobes.
To fix this problem, we just need to clear the TF bit when
resetting running kprobe.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: systemtap@sourceware.org
Link: http://lkml.kernel.org/r/20160611140648.25885.37482.stgit@devbox
[ Updated the comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 56530f5d2d upstream.
Currently pmd_mknotpresent will use a zero entry to respresent an
invalidated pmd.
Unfortunately this definition clashes with pmd_none, thus it is
possible for a race condition to occur if zap_pmd_range sees pmd_none
whilst __split_huge_pmd_locked is running too with pmdp_invalidate
just called.
This patch fixes the race condition by modifying pmd_mknotpresent to
create non-zero faulting entries (as is done in other architectures),
removing the ambiguity with pmd_none.
[catalin.marinas@arm.com: using L_PMD_SECT_VALID instead of PMD_TYPE_SECT]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.16: also convert from a macro to a function, as done
earlier upstream]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6245318869 upstream.
In a subsequent patch, pmd_mknotpresent will clear the valid bit of the
pmd entry, resulting in a not-present entry from the hardware's
perspective. Unfortunately, pmd_present simply checks for a non-zero pmd
value and will therefore continue to return true even after a
pmd_mknotpresent operation. Since pmd_mknotpresent is only used for
managing huge entries, this is only an issue for the 3-level case.
This patch fixes the 3-level pmd_present implementation to take into
account the valid bit. For bisectability, the change is made before the
fix to pmd_mknotpresent.
[catalin.marinas@arm.com: comment update regarding pmd_mknotpresent patch]
Fixes: 8d96250700 ("ARM: mm: Transparent huge page support for LPAE systems.")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Steve Capper <Steve.Capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9c77679cad upstream.
For newer versions of Syslinux, we need ldlinux.c32 in addition to
isolinux.bin to reside on the boot disk, so if the latter is found,
copy it, too, to the isoimage tree.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8a934efe94 upstream.
In commit 8445a87f70 "powerpc/iommu: Remove the dependency on EEH
struct in DDW mechanism", the PE address was replaced with the PCI
config address in order to remove dependency on EEH. According to PAPR
spec, firmware (pHyp or QEMU) should accept "xxBBSSxx" format PCI config
address, not "xxxxBBSS" provided by the patch. Note that "BB" is PCI bus
number and "SS" is the combination of slot and function number.
This fixes the PCI address passed to DDW RTAS calls.
Fixes: 8445a87f70 ("powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism")
Reported-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8b78f26088 upstream.
One of the debian buildd servers had this crash in the syslog without
any other information:
Unaligned handler failed, ret = -2
clock_adjtime (pid 22578): Unaligned data reference (code 28)
CPU: 1 PID: 22578 Comm: clock_adjtime Tainted: G E 4.5.0-2-parisc64-smp #1 Debian 4.5.4-1
task: 000000007d9960f8 ti: 00000001bde7c000 task.ti: 00000001bde7c000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00001000000001001111100000001111 Tainted: G E
r00-03 000000ff0804f80f 00000001bde7c2b0 00000000402d2be8 00000001bde7c2b0
r04-07 00000000409e1fd0 00000000fa6f7fff 00000001bde7c148 00000000fa6f7fff
r08-11 0000000000000000 00000000ffffffff 00000000fac9bb7b 000000000002b4d4
r12-15 000000000015241c 000000000015242c 000000000000002d 00000000fac9bb7b
r16-19 0000000000028800 0000000000000001 0000000000000070 00000001bde7c218
r20-23 0000000000000000 00000001bde7c210 0000000000000002 0000000000000000
r24-27 0000000000000000 0000000000000000 00000001bde7c148 00000000409e1fd0
r28-31 0000000000000001 00000001bde7c320 00000001bde7c350 00000001bde7c218
sr00-03 0000000001200000 0000000001200000 0000000000000000 0000000001200000
sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ: 0000000000000000 0000000000000000 IAOQ: 00000000402d2e84 00000000402d2e88
IIR: 0ca0d089 ISR: 0000000001200000 IOR: 00000000fa6f7fff
CPU: 1 CR30: 00000001bde7c000 CR31: ffffffffffffffff
ORIG_R28: 00000002369fe628
IAOQ[0]: compat_get_timex+0x2dc/0x3c0
IAOQ[1]: compat_get_timex+0x2e0/0x3c0
RP(r2): compat_get_timex+0x40/0x3c0
Backtrace:
[<00000000402d4608>] compat_SyS_clock_adjtime+0x40/0xc0
[<0000000040205024>] syscall_exit+0x0/0x14
This means the userspace program clock_adjtime called the clock_adjtime()
syscall and then crashed inside the compat_get_timex() function.
Syscalls should never crash programs, but instead return EFAULT.
The IIR register contains the executed instruction, which disassebles
into "ldw 0(sr3,r5),r9".
This load-word instruction is part of __get_user() which tried to read the word
at %r5/IOR (0xfa6f7fff). This means the unaligned handler jumped in. The
unaligned handler is able to emulate all ldw instructions, but it fails if it
fails to read the source e.g. because of page fault.
The following program reproduces the problem:
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/mman.h>
int main(void) {
/* allocate 8k */
char *ptr = mmap(NULL, 2*4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0);
/* free second half (upper 4k) and make it invalid. */
munmap(ptr+4096, 4096);
/* syscall where first int is unaligned and clobbers into invalid memory region */
/* syscall should return EFAULT */
return syscall(__NR_clock_adjtime, 0, ptr+4095);
}
To fix this issue we simply need to check if the faulting instruction address
is in the exception fixup table when the unaligned handler failed. If it
is, call the fixup routine instead of crashing.
While looking at the unaligned handler I found another issue as well: The
target register should not be modified if the handler was unsuccessful.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e2dfb4b880 upstream.
PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Fixes: 8130b9d7b9 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers")
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Simon Marchi <simon.marchi@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e47b020a32 upstream.
This patch brings the PER_LINUX32 /proc/cpuinfo format more in line with
the 32-bit ARM one by providing an additional line:
model name : ARMv8 Processor rev X (v8l)
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16:
- Adjust filename, context
- Open-code MIDR_REVISION()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8dd75ccb57 upstream.
We are already using the privileged versions of MMCR0, MMCR1
and MMCRA in the kernel, so for MMCR2, we should better use
the privileged versions, too, to be consistent.
Fixes: 240686c136 ("powerpc: Initialise PMU related regs on Power8")
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d23fac2b27 upstream.
The SIAR and SDAR registers are available twice, one time as SPRs
780 / 781 (unprivileged, but read-only), and one time as the SPRs
796 / 797 (privileged, but read and write). The Linux kernel code
currently uses the unprivileged SPRs - while this is OK for reading,
writing to that register of course does not work.
Since the KVM code tries to write to this register, too (see the mtspr
in book3s_hv_rmhandlers.S), the contents of this register sometimes get
lost for the guests, e.g. during migration of a VM.
To fix this issue, simply switch to the privileged SPR numbers instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 871e178e0f upstream.
In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the
spec states that values of 9900-9905 can be returned, indicating that
software should delay for 10^x (where x is the last digit, i.e. 990x)
milliseconds and attempt the call again. Currently, the kernel doesn't
know about this, and respecting it fixes some PCI failures when the
hypervisor is busy.
The delay is capped at 0.2 seconds.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 70dff4d90a upstream.
Commit d96cc3d1ec "MIPS: Add microMIPS MSA support." attempted to use
the value of a macro within an inline asm statement but instead emitted
a comment leading to the cfcmsa & ctcmsa instructions being omitted. Fix
that by passing CFC_MSA_INSN & CTC_MSA_INSN as arguments to the asm
statements.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit da77b67195 upstream.
Commit b894157145 ("x86/PCI: Mark Broadwell-EP Home Agent & PCU as having
non-compliant BARs") marked Home Agent 0 & PCU has having non-compliant
BARs. Home Agent 1 also has non-compliant BARs.
Mark Home Agent 1 as having non-compliant BARs so the PCI core doesn't
touch them.
The problem with these devices is documented in the Xeon v4 specification
update:
BDF2 PCI BARs in the Home Agent Will Return Non-Zero Values
During Enumeration
Problem: During system initialization the Operating System may access
the standard PCI BARs (Base Address Registers). Due to
this erratum, accesses to the Home Agent BAR registers (Bus
1; Device 18; Function 0,4; Offsets (0x14-0x24) will return
non-zero values.
Implication: The operating system may issue a warning. Intel has not
observed any functional failures due to this erratum.
Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v4-spec-update.html
Fixes: b894157145 ("x86/PCI: Mark Broadwell-EP Home Agent & PCU as having non-compliant BARs")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ab4a92e667 upstream.
When emulating a jalr instruction with rd == $0, the code in
isBranchInstr was incorrectly writing to GPR $0 which should actually
always remain zeroed. This would lead to any further instructions
emulated which use $0 operating on a bogus value until the task is next
context switched, at which point the value of $0 in the task context
would be restored to the correct zero by a store in SAVE_SOME. Fix this
by not writing to rd if it is $0.
Fixes: 102cedc32a ("MIPS: microMIPS: Floating point support.")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4d46a67a3e upstream.
The lazy cache flushing implemented in the MIPS kernel suffers from a
race condition that is exposed by do_set_pte() in mm/memory.c.
A pre-condition is a file-system that writes to the page from the CPU
in its readpage method and then calls flush_dcache_page(). One example
is ubifs. Another pre-condition is that the dcache flush is postponed
in __flush_dcache_page().
Upon a page fault for an executable mapping not existing in the
page-cache, the following will happen:
1. Write to the page
2. flush_dcache_page
3. flush_icache_page
4. set_pte_at
5. update_mmu_cache (commits the flush of a dcache-dirty page)
Between steps 4 and 5 another thread can hit the same page and it will
encounter a valid pte. Because the data still is in the L1 dcache the CPU
will fetch stale data from L2 into the icache and execute garbage.
This fix moves the commit of the cache flush to step 3 to close the
race window. It also reduces the amount of flushes on non-executable
mappings because we never enter __flush_dcache_page() for non-aliasing
CPUs.
Regressions can occur in drivers that mistakenly relies on the
flush_dcache_page() in get_user_pages() for DMA operations.
[ralf@linux-mips.org: Folded in patch 9346 to fix highmem issue.]
Signed-off-by: Lars Persson <larper@axis.com>
Cc: linux-mips@linux-mips.org
Cc: paul.burton@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9346/
Patchwork: https://patchwork.linux-mips.org/patch/9738/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8445a87f70 upstream.
Commit 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
changed the pci_dn struct by removing its EEH-related members.
As part of this clean-up, DDW mechanism was modified to read the device
configuration address from eeh_dev struct.
As a consequence, now if we disable EEH mechanism on kernel command-line
for example, the DDW mechanism will fail, generating a kernel oops by
dereferencing a NULL pointer (which turns to be the eeh_dev pointer).
This patch just changes the configuration address calculation on DDW
functions to a manual calculation based on pci_dn members instead of
using eeh_dev-based address.
No functional changes were made. This was tested on pSeries, both
in PHyp and qemu guest.
Fixes: 39baadbf36 ("powerpc/eeh: Remove eeh information from pci_dn")
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aac55d7573 upstream.
With Linux page size of 64K and hardware only supporting 4K HPTE, if we
use subpage protection, we always fail for the subpage 0 as shown
below (using the selftest subpage_prot test):
520175565: (4520111850): Failed at 0x3fffad4b0000 (p=13,sp=0,w=0), want=fault, got=pass !
4520890210: (4520826495): Failed at 0x3fffad5b0000 (p=29,sp=0,w=0), want=fault, got=pass !
4521574251: (4521510536): Failed at 0x3fffad6b0000 (p=45,sp=0,w=0), want=fault, got=pass !
4522258324: (4522194609): Failed at 0x3fffad7b0000 (p=61,sp=0,w=0), want=fault, got=pass !
This is because hash preload wrongly inserts the HPTE entry for subpage
0 without looking at the subpage protection information.
Fix it by teaching should_hash_preload() not to preload if we have
subpage protection configured for that range.
It appears this has been broken since it was introduced in 2008.
Fixes: fa28237cfc ("[POWERPC] Provide a way to protect 4k subpages when using 64k pages")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rework into should_hash_preload() to avoid build fails w/SLICES=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8bbc9b7b00 upstream.
Currently we have a check in hash_preload() against the psize, which is
only included when CONFIG_PPC_MM_SLICES is enabled. We want to expand
this check in a subsequent patch, so factor it out to allow that. As a
bonus it removes the #ifdef in the C code.
Unfortunately we can't put this in the existing CONFIG_PPC_MM_SLICES
block because it would require a forward declaration.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f228b494e5 upstream.
The loop that browses the array compat_hwcap_str will stop when a NULL
is encountered, however NULL is missing at the end of array. This will
lead to overrun until a NULL is found somewhere in the following memory.
In reality, this works out because the compat_hwcap2_str array tends to
follow immediately in memory, and that *is* terminated correctly.
Furthermore, the unsigned int compat_elf_hwcap is checked before
printing each capability, so we end up doing the right thing because
the size of the two arrays is less than 32. Still, this is an obvious
mistake and should be fixed.
Note for backporting: commit 12d11817ea ("arm64: Move
/proc/cpuinfo handling code") moved this code in v4.4. Prior to that
commit, the same change should be made in arch/arm64/kernel/setup.c.
Fixes: 44b82b7700 "arm64: Fix up /proc/cpuinfo"
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c34a69059d upstream.
The identity mapping is suboptimal for the last 2GB frame. The mapping
will be established with a mix of 4KB and 1MB mappings instead of a
single 2GB mapping.
This happens because of a off-by-one bug introduced with
commit 50be634507 ("s390/mm: Convert bootmem to memblock").
Currently the identity mapping looks like this:
0x0000000080000000-0x0000000180000000 4G PUD RW
0x0000000180000000-0x00000001fff00000 2047M PMD RW
0x00000001fff00000-0x0000000200000000 1M PTE RW
With the bug fixed it looks like this:
0x0000000080000000-0x0000000200000000 6G PUD RW
Fixes: 50be634507 ("s390/mm: Convert bootmem to memblock")
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b45bacd2d0 upstream.
Writing CP0_Compare clears the timer interrupt pending bit
(CP0_Cause.TI), but this wasn't being done atomically. If a timer
interrupt raced with the write of the guest CP0_Compare, the timer
interrupt could end up being pending even though the new CP0_Compare is
nowhere near CP0_Count.
We were already updating the hrtimer expiry with
kvm_mips_update_hrtimer(), which used both kvm_mips_freeze_hrtimer() and
kvm_mips_resume_hrtimer(). Close the race window by expanding out
kvm_mips_update_hrtimer(), and clearing CP0_Cause.TI and setting
CP0_Compare between the freeze and resume. Since the pending timer
interrupt should not be cleared when CP0_Compare is written via the KVM
user API, an ack argument is added to distinguish the source of the
write.
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4355c44f06 upstream.
There's a particularly narrow and subtle race condition when the
software emulated guest timer is frozen which can allow a guest timer
interrupt to be missed.
This happens due to the hrtimer expiry being inexact, so very
occasionally the freeze time will be after the moment when the emulated
CP0_Count transitions to the same value as CP0_Compare (so an IRQ should
be generated), but before the moment when the hrtimer is due to expire
(so no IRQ is generated). The IRQ won't be generated when the timer is
resumed either, since the resume CP0_Count will already match CP0_Compare.
With VZ guests in particular this is far more likely to happen, since
the soft timer may be frozen frequently in order to restore the timer
state to the hardware guest timer. This happens after 5-10 hours of
guest soak testing, resulting in an overflow in guest kernel timekeeping
calculations, hanging the guest. A more focussed test case to
intentionally hit the race (with the help of a new hypcall to cause the
timer state to migrated between hardware & software) hits the condition
fairly reliably within around 30 seconds.
Instead of relying purely on the inexact hrtimer expiry to determine
whether an IRQ should be generated, read the guest CP0_Compare and
directly check whether the freeze time is before or after it. Only if
CP0_Count is on or after CP0_Compare do we check the hrtimer expiry to
determine whether the last IRQ has already been generated (which will
have pushed back the expiry by one timer period).
Fixes: e30492bbe9 ("MIPS: KVM: Rewrite count/compare timer emulation")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 128639395b upstream.
Update the recent changes to set_pte() that were added in 46011e6ea3
to handle R10000_LLSC_WAR, and format the assembly to match other areas
of the MIPS tree using the same WAR.
This also incorporates a patch recently sent in my Markos Chandras,
"Remove local LL/SC preprocessor variants", so that patch doesn't need
to be applied if this one is accepted.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Fixes: 46011e6ea3 ("MIPS: Make set_pte() SMP safe.)
Cc: David Daney <david.daney@cavium.com>
Cc: Linux/MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/11103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[bwh: Backported to 3.2:
- Use {LL,SC}_INSN not __{LL,SC}
- Use literal arch=r4000 instead of MIPS_ISA_ARCH_LEVEL since R6 is not
supported]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 81a76d7119 upstream.
When showing backtraces in response to traps, for example crashes and
address errors (usually unaligned accesses) when they are set in debugfs
to be reported, unwind_stack will be used if the PC was in the kernel
text address range. However since EVA it is possible for user and kernel
address ranges to overlap, and even without EVA userland can still
trigger an address error by jumping to a KSeg0 address.
Adjust the check to also ensure that it was running in kernel mode. I
don't believe any harm can come of this problem, since unwind_stack() is
sufficiently defensive, however it is only meant for unwinding kernel
code, so to be correct it should use the raw backtracing instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
(cherry picked from commit d2941a975ac745c607dfb590e92bb30bc352dad9)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a816b306c6 upstream.
When unwinding through IRQs and exceptions, the unwinding only continues
if the PC is a kernel text address, however since EVA it is possible for
user and kernel address ranges to overlap, potentially allowing
unwinding to continue to user mode if the user PC happens to be in the
kernel text address range.
Adjust the check to also ensure that the register state from before the
exception is actually running in kernel mode, i.e. !user_mode(regs).
I don't believe any harm can come of this problem, since the PC is only
output, the stack pointer is checked to ensure it resides within the
task's stack page before it is dereferenced in search of the return
address, and the return address register is similarly only output (if
the PC is in a leaf function or the beginning of a non-leaf function).
However unwind_stack() is only meant for unwinding kernel code, so to be
correct the unwind should stop there.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5daebc477d upstream.
Commit 85efde6f4e ("make exported headers use strict posix types")
changed the asm-generic siginfo.h to use the __kernel_* types, and
commit 3a471cbc08 ("remove __KERNEL_STRICT_NAMES") make the internal
types accessible only to the kernel, but the MIPS implementation hasn't
been updated to match.
Switch to proper types now so that the exported asm/siginfo.h won't
produce quite so many compiler errors when included alone by a user
program.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Christopher Ferris <cferris@google.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12477/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5bb1cc0ff9 upstream.
Currently, pmd_present() only checks for a non-zero value, returning
true even after pmd_mknotpresent() (which only clears the type bits).
This patch converts pmd_present() to using pte_present(), similar to the
other pmd_*() checks. As a side effect, it will return true for
PROT_NONE mappings, though they are not yet used by the kernel with
transparent huge pages.
For consistency, also change pmd_mknotpresent() to only clear the
PMD_SECT_VALID bit, even though the PMD_TABLE_BIT is already 0 for block
mappings (no functional change). The unused PMD_SECT_PROT_NONE
definition is removed as transparent huge pages use the pte page prot
values.
Fixes: 9c7e535fcc ("arm64: mm: Route pmd thp functions through pte equivalents")
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f5b556c94c upstream.
This makes the ath79 bootconsole behave the same way as the generic 8250
bootconsole.
Also waiting for TEMT (transmit buffer is empty) instead of just THRE
(transmit buffer is not full) ensures that all characters have been
transmitted before the real serial driver starts reconfiguring the serial
controller (which would sometimes result in garbage being transmitted.)
This change does not cause a visible performance loss.
In addition, this seems to fix a hang observed in certain configurations on
many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver.
A more complete follow-up patch will disable 8250 autoconfig for ath79
altogether (the serial controller is detected as a 16550A, which is not
fully compatible with the ath79 serial, and the autoconfig may lead to
undefined behavior on ath79.)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d4b9e0790a upstream.
The ARM architecture mandates that when changing a page table entry
from a valid entry to another valid entry, an invalid entry is first
written, TLB invalidated, and only then the new entry being written.
The current code doesn't respect this, directly writing the new
entry and only then invalidating TLBs. Let's fix it up.
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c20e128030 upstream.
The alpha pci_mmap_resource() is used for both IORESOURCE_MEM and
IORESOURCE_IO resources, but iomem_is_exclusive() is only applicable for
IORESOURCE_MEM.
Call iomem_is_exclusive() only for IORESOURCE_MEM resources, and do it
earlier to match the generic version of pci_mmap_resource().
Fixes: 10a0ef39fb ("PCI/alpha: pci sysfs resources")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8ed8ab4004 upstream.
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit
429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb ("powerpc: Add relocation on exception vector handlers")
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c20c8f750d upstream.
The omap_hwmod _enable() function can return success without setting
the hwmod state to _HWMOD_STATE_ENABLED for IPs with reset lines when
all of the reset lines are asserted. The omap_hwmod _idle() function
also performs a similar check, but after checking for the hwmod state
first. This triggers the WARN when pm_runtime_get and pm_runtime_put
are invoked on IPs with all reset lines asserted. Reverse the checks
for hwmod state and reset lines status to fix this.
Issue found during a unbind operation on a device with reset lines
still asserted, example backtrace below
------------[ cut here ]------------
WARNING: CPU: 1 PID: 879 at arch/arm/mach-omap2/omap_hwmod.c:2207 _idle+0x1e4/0x240()
omap_hwmod: mmu_dsp: idle state can only be entered from enabled state
Modules linked in:
CPU: 1 PID: 879 Comm: sh Not tainted 4.4.0-00008-ga989d951331a #3
Hardware name: Generic OMAP5 (Flattened Device Tree)
[<c0018e60>] (unwind_backtrace) from [<c0014dc4>] (show_stack+0x10/0x14)
[<c0014dc4>] (show_stack) from [<c037ac28>] (dump_stack+0x90/0xc0)
[<c037ac28>] (dump_stack) from [<c003f420>] (warn_slowpath_common+0x78/0xb4)
[<c003f420>] (warn_slowpath_common) from [<c003f48c>] (warn_slowpath_fmt+0x30/0x40)
[<c003f48c>] (warn_slowpath_fmt) from [<c0028c20>] (_idle+0x1e4/0x240)
[<c0028c20>] (_idle) from [<c0029080>] (omap_hwmod_idle+0x28/0x48)
[<c0029080>] (omap_hwmod_idle) from [<c002a5a4>] (omap_device_idle+0x3c/0x90)
[<c002a5a4>] (omap_device_idle) from [<c0427a90>] (__rpm_callback+0x2c/0x60)
[<c0427a90>] (__rpm_callback) from [<c0427ae4>] (rpm_callback+0x20/0x80)
[<c0427ae4>] (rpm_callback) from [<c0427f84>] (rpm_suspend+0x138/0x74c)
[<c0427f84>] (rpm_suspend) from [<c0428b78>] (__pm_runtime_idle+0x78/0xa8)
[<c0428b78>] (__pm_runtime_idle) from [<c041f514>] (__device_release_driver+0x64/0x100)
[<c041f514>] (__device_release_driver) from [<c041f5d0>] (device_release_driver+0x20/0x2c)
[<c041f5d0>] (device_release_driver) from [<c041d85c>] (unbind_store+0x78/0xf8)
[<c041d85c>] (unbind_store) from [<c0206df8>] (kernfs_fop_write+0xc0/0x1c4)
[<c0206df8>] (kernfs_fop_write) from [<c018a120>] (__vfs_write+0x20/0xdc)
[<c018a120>] (__vfs_write) from [<c018a9cc>] (vfs_write+0x90/0x164)
[<c018a9cc>] (vfs_write) from [<c018b1f0>] (SyS_write+0x44/0x9c)
[<c018b1f0>] (SyS_write) from [<c0010420>] (ret_fast_syscall+0x0/0x1c)
---[ end trace a4182013c75a9f50 ]---
While at this, fix the sequence in _shutdown() as well, though there
is no easy reproducible scenario.
Fixes: 747834ab83 ("ARM: OMAP2+: hwmod: revise hardreset behavior")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9ec423ed62 upstream.
Commit be3d7d023b ("ARM: kirkwood: Add DTS file for NSA320")
created the new file kirkwood-nsa320.dts but did not
add it to the Makefile.
Fixes: be3d7d023b ("ARM: kirkwood: Add DTS file for NSA320")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fc5c796e12 upstream.
Commit 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology
NAS devices") created the new file kirkwood-ds112.dts but did not
add it to the Makefile.
Fixes: 2d0a7addbd ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
