commit 5f25f066f7 upstream.
time_in_state in struct devfreq is defined as unsigned long, so
devm_kzalloc should use sizeof(unsigned long) as argument instead
of sizeof(unsigned int), otherwise it will cause unexpected result
in 64bit system.
Signed-off-by: Xiaolong Ye <yexl@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9a035a40f7 upstream.
This should really only be done for XS_TRANSACTION_END messages, or
else at least some of the xenstore-* tools don't work anymore.
Fixes: 0beef634b8 ("xenbus: don't BUG() on user mode induced condition")
Reported-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Tested-by: Richard Schütz <rschuetz@uni-koblenz.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0beef634b8 upstream.
Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ed Swierk <eswierk@skyportsystems.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5ca05345c5 upstream.
For counter subdevices, the `s->insn_write` handler is being set to the
wrong function, `ni_tio_insn_read()`. It should be
`ni_tio_insn_write()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Éric Piel <piel@delmic.com>
Fixes: 10f74377ee ("staging: comedi: ni_tio: make ni_tio_winsn() a
proper comedi (*insn_write)")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d5468d7afa upstream.
Commit 588afcc1c0 ("[media] usbvision fix overflow of interfaces
array")' should be reverted, because:
* "!dev->actconfig->interface[ifnum]" won't catch a case where the value
is not NULL but some garbage. This way the system may crash later with
GPF.
* "(ifnum >= USB_MAXINTERFACES)" does not cover all the error
conditions. "ifnum" should be compared to "dev->actconfig->
desc.bNumInterfaces", i.e. compared to the number of "struct
usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES.
* There is a "struct usb_device" leak in this error path, as there is
usb_get_dev(), but no usb_put_dev() on this path.
* There is a bug of the same type several lines below with number of
endpoints. The code is accessing hard-coded second endpoint
("interface->endpoint[1].desc") which may not exist. It would be great
to handle this in the same patch too.
* All the concerns above are resolved by already-accepted commit fa52bd50
("[media] usbvision: fix crash on detecting device with invalid
configuration")
* Mailing list message:
http://www.spinics.net/lists/linux-media/msg94832.html
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 31051c85b5 upstream.
inode_change_ok() will be resposible for clearing capabilities and IMA
extended attributes and as such will need dentry. Give it as an argument
to inode_change_ok() instead of an inode. Also rename inode_change_ok()
to setattr_prepare() to better relect that it does also some
modifications in addition to checks.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
[bwh: Backported to 3.16:
- Drop changes to orangefs, overlayfs
- Adjust filenames, context
- In fuse, pass dentry to fuse_do_setattr()
- In nfsd, pass dentry to nfsd_sanitize_attrs()
- In xfs, pass dentry to xfs_setattr_nonsize() and xfs_setattr_size()
- Update ext3 as well]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 05692d7005 upstream.
The VFIO_DEVICE_SET_IRQS ioctl did not sufficiently sanitize
user-supplied integers, potentially allowing memory corruption. This
patch adds appropriate integer overflow checks, checks the range bounds
for VFIO_IRQ_SET_DATA_NONE, and also verifies that only single element
in the VFIO_IRQ_SET_DATA_TYPE_MASK bitmask is set.
VFIO_IRQ_SET_ACTION_TYPE_MASK is already correctly checked later in
vfio_pci_set_irqs_ioctl().
Furthermore, a kzalloc is changed to a kcalloc because the use of a
kzalloc with an integer multiplication allowed an integer overflow
condition to be reached without this patch. kcalloc checks for overflow
and should prevent a similar occurrence.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ded8991215 upstream.
User-space can choose to omit NL80211_ATTR_SSID and only provide raw
IE TLV data. When doing so it can provide SSID IE with length exceeding
the allowed size. The driver further processes this IE copying it
into a local variable without checking the length. Hence stack can be
corrupted and used as exploit.
Reported-by: Daxing Guo <freener.gdx@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 667121ace9 upstream.
The IP-over-1394 driver firewire-net lacked input validation when
handling incoming fragmented datagrams. A maliciously formed fragment
with a respectively large datagram_offset would cause a memcpy past the
datagram buffer.
So, drop any packets carrying a fragment with offset + length larger
than datagram_size.
In addition, ensure that
- GASP header, unfragmented encapsulation header, or fragment
encapsulation header actually exists before we access it,
- the encapsulated datagram or fragment is of nonzero size.
Reported-by: Eyal Itkin <eyal.itkin@gmail.com>
Reviewed-by: Eyal Itkin <eyal.itkin@gmail.com>
Fixes: CVE 2016-8633
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7bc2b55a5c upstream.
We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16:
- Adjust context
- Use literal 1032 insetad of ARCMSR_API_DATA_BUFLEN]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 331dcf421c upstream.
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9abefcb1aa upstream.
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
[1] https://github.com/victronenergy/venus/issues/24
Signed-off-by: Sergei Miroshnichenko <sergeimir@emcraft.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 463e8f845c upstream.
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 371a015344 upstream.
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4de349e786 upstream.
On a imx6ul-pico board the following error is seen during system suspend:
dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8ec07bf8a8 upstream.
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit baa0be7026 upstream.
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e5ac40cd66 upstream.
Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.
This fix separates scope bits and join states bits a nibble each.
Fixes: b9c5d6a643 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 344bacca8c upstream.
This fix solves a race between light flush and on the fly joins.
Light flush doesn't set the device to down and unset IPOIB_OPER_UP
flag, this means that if while flushing we have a MC join in progress
and the QP was attached to BC MGID we can have a mismatches when
re-attaching a QP to the BC MGID.
The light flush would set the broadcast group to NULL causing an on
the fly join to rejoin and reattach to the BC MCG as well as adding
the BC MGID to the multicast list. The flush process would later on
remove the BC MGID and detach it from the QP. On the next flush
the BC MGID is present in the multicast list but not found when trying
to detach it because of the previous double attach and single detach.
[18332.714265] ------------[ cut here ]------------
[18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core]
...
[18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
[18332.779411] 0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000
[18332.784960] 0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300
[18332.790547] ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280
[18332.796199] Call Trace:
[18332.798015] [<ffffffff813fed47>] dump_stack+0x63/0x8c
[18332.801831] [<ffffffff8109add1>] __warn+0xd1/0xf0
[18332.805403] [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20
[18332.809706] [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core]
[18332.814384] [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib]
[18332.820031] [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib]
[18332.825220] [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib]
[18332.830290] [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib]
[18332.834911] [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0
[18332.839741] [<ffffffff81772bd1>] rollback_registered+0x31/0x40
[18332.844091] [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80
[18332.848880] [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib]
[18332.853848] [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib]
[18332.858474] [<ffffffff81520c08>] dev_attr_store+0x18/0x30
[18332.862510] [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50
[18332.866349] [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170
[18332.870471] [<ffffffff81207198>] __vfs_write+0x28/0xe0
[18332.874152] [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50
[18332.878274] [<ffffffff81208062>] vfs_write+0xa2/0x1a0
[18332.881896] [<ffffffff812093a6>] SyS_write+0x46/0xa0
[18332.885632] [<ffffffff810039b7>] do_syscall_64+0x57/0xb0
[18332.889709] [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25
[18332.894727] ---[ end trace 09ebbe31f831ef17 ]---
Fixes: ee1e2c82c2 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 08c5cd3748 upstream.
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f190fd9245 upstream.
This patch adds support for Infineon flashloader 0x8087/0x0801.
The flashloader is used in Telit LE940B modem family with Telit
flashing application.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f6d7c1b559 upstream.
This fixes subpage writes when using 4-bit HW ECC.
There has been numerous reports about ECC errors with devices using this
driver for a while. Also the 4-bit ECC has been reported as broken with
subpages in [1] and with 16 bits NANDs in the driver and in mach* board
files both in mainline and in the vendor BSPs.
What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to
try reinitializing the ECC engine:
- R/W on whole pages properly generates/checks RS code
- try writing the 1st subpage only of a blank page, the subpage is well
written and the RS code properly generated, re-reading the same page
the HW detects some ECC error, reading the same page again no ECC
error is detected
Note that the ECC engine is already reinitialized in the 1-bit case.
Tested on my LCDK with UBI+UBIFS using subpages.
This could potentially get rid of the issue workarounded in [1].
[1] 28c015a9da ("mtd: davinci-nand: disable subpage write for keystone-nand")
Fixes: 6a4123e581 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 171c009183 upstream.
7985e7c100 ("iio: Introduce a new fractional value type") introduced a
new IIO_VAL_FRACTIONAL value type meant to represent rational type numbers
expressed by a numerator and denominator combination.
Formating of IIO_VAL_FRACTIONAL values relies upon do_div() usage. This
fails handling negative values properly since parameters are reevaluated
as unsigned values.
Fix this by using div_s64_rem() instead. Computed integer part will carry
properly signed value. Formatted fractional part will always be positive.
Fixes: 7985e7c100 ("iio: Introduce a new fractional value type")
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit dadb57abc3 upstream.
efi_get_memory_map() allocates a buffer to store the memory map that it
retrieves. This buffer may need to be reused by the client after
ExitBootServices() is called, at which point allocations are not longer
permitted. To support this usecase, provide the allocated buffer size back
to the client, and allocate some additional headroom to account for any
reasonable growth in the map that is likely to happen between the call to
efi_get_memory_map() and the client reusing the buffer.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
[bwh: Backported to 3.16:
- Adjust filenames, context
- In allocate_new_fdt_and_exit_boot(), only fill memory_map
- Drop changes to efi_random_alloc()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 519d8bd4b5 upstream.
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
Fixes: d5c6a1e024 ("usb: renesas_usbhs: fixup interrupt status clear method")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 307fe9dd11 upstream.
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
$cat in_accel_scale
-1057462640.011978
Fix this by assigning zero to the integer part.
Tested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 36afb176d3 upstream.
According to IIO ABI definition, IIO_PRESSURE data output unit is
kilopascal:
http://lxr.free-electrons.com/source/Documentation/ABI/testing/sysfs-bus-iio
This patch fix output unit of HID pressure sensor IIO driver from pascal to
kilopascal to follow IIO ABI definition.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 546481c281 upstream.
When a new CM connection is being requested, ipoib driver copies data
from the path pointer in the CM/tx object, the path object might be
invalid at the point and memory corruption will happened later when now
the CM driver will try using that data.
The next scenario demonstrates it:
neigh_add_path --> ipoib_cm_create_tx -->
queue_work (pointer to path is in the cm/tx struct)
#while the work is still in the queue,
#the port goes down and causes the ipoib_flush_paths:
ipoib_flush_paths --> path_free --> kfree(path)
#at this point the work scheduled starts.
ipoib_cm_tx_start --> copy from the (invalid)path pointer:
(memcpy(&pathrec, &p->path->pathrec, sizeof pathrec);)
-> memory corruption.
To fix that the driver now starts the CM/tx connection only if that
specific path exists in the general paths database.
This check is protected with the relevant locks, and uses the gid from
the neigh member in the CM/tx object which is valid according to the ref
count that was taken by the CM/tx.
Fixes: 839fcaba35 ('IPoIB: Connected mode experimental support')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 68c6bcdd8b upstream.
The function send_leave sets the member: group->query_id
(group->query_id = ret) after calling the sa_query, but leave_handler
can be executed before the setting and it might delete the group object,
and will get a memory corruption.
Additionally, this patch gets rid of group->query_id variable which is
not used.
Fixes: faec2f7b96 ('IB/sa: Track multicast join/leave requests')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c8d192428f upstream.
Added devices ids for acces i/o products quad and octal serial cards
that make use of existing Pericom PI7C9X7954 and PI7C9X7958
configurations .
Signed-off-by: Jimi Damon <jdamon@accesio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5d0be84ec0 upstream.
If crypt_alloc_tfms() had to allocate multiple tfms and it failed before
the last allocation, then it would call crypt_free_tfms() and could free
pointers from uninitialized memory -- due to the crypt_free_tfms() check
for non-zero cc->tfms[i]. Fix by allocating zeroed memory.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d78d383ab3 upstream.
An evil userspace could try to cause deadlock by passing an unfaulted-in
GEM bo as submit->bos (or submit->cmds) table. Which will trigger
msm_gem_fault() while we already hold struct_mutex. See:
https://github.com/freedreno/msmtest/blob/master/evilsubmittest.c
Signed-off-by: Rob Clark <robdclark@gmail.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 89f82cbb0d upstream.
Use instead __copy_from_user_inatomic() and fallback to slow-path where
we drop and re-aquire the lock in case of fault.
Reported-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b5b4c264df upstream.
Be kinder to things that do lots of signal handling (ie. Xorg)
Signed-off-by: Rob Clark <robdclark@gmail.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b53e7d000d upstream.
The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.
In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.
Clear any pending interrupts after we stop the timer in the probe
function to avoid this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 40d9c32525 upstream.
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7b996243fa upstream.
Instead of using sock_tx_timestamp, use skb_tx_timestamp to record
software transmit timestamp of a packet.
sock_tx_timestamp resets and overrides the tx_flags of the skb.
The function is intended to be called from within the protocol
layer when creating the skb, not from a device driver. This is
inconsistent with other drivers and will cause issues for TCP.
In TCP, we intend to sample the timestamps for the last byte
for each sendmsg/sendpage. For that reason, tcp_sendmsg calls
tcp_tx_timestamp only with the last skb that it generates.
For example, if a 128KB message is split into two 64KB packets
we want to sample the SND timestamp of the last packet. The current
code in the tun driver, however, will result in sampling the SND
timestamp for both packets.
Also, when the last packet is split into smaller packets for
retranmission (see tcp_fragment), the tun driver will record
timestamps for all of the retransmitted packets and not only the
last packet.
Fixes: eda2977291 (tun: Support software transmit time stamping.)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Francis Yan <francisyyan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: call to sock_tx_timestamp() was different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 53e5f36fbd upstream.
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6c73358c83 upstream.
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fae16989be upstream.
Commit fe6b0dfaba ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Fixes: fe6b0dfaba ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f4693b08cc upstream.
We can't assign -EINVAL to a u16.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6f00975c61 upstream.
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Reported-by: Alexander Potapenko <glider@google.com>
Cc: Alexander Potapenko <glider@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7ac61a062f upstream.
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 90c43ec699 upstream.
It is possible that two or more ADC channels can be simultaneously
requested for raw samples, in which case there can be race in access to
FIFO data resulting in loss of samples.
If am335x_tsc_se_set_once() is called again from tiadc_read_raw(), when
ADC is still acquired to sample one of the channels, the second process
might be put into uninterruptible sleep state. Fix these issues, by
protecting FIFO access and channel configurations with a mutex. Since
tiadc_read_raw() might take anywhere between few microseconds to few
milliseconds to finish execution (depending on averaging and delay
values supplied via DT), its better to use mutex instead of spinlock.
Fixes: 7ca6740cd1 ("mfd: input: iio: ti_amm335x: Rework TSC/ADC synchronization")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f0f4b0cc3a upstream.
Commit ebb657babf ("staging: comedi: ni_mio_common: clarify the
cmd->start_arg validation and use") introduced a backwards compatibility
issue in the use of asynchronous commands on the AO subdevice when
`start_src` is `TRIG_EXT`. Valid values for `start_src` are `TRIG_INT`
(for internal, software trigger), and `TRIG_EXT` (for external trigger).
When set to `TRIG_EXT`. In both cases, the driver relies on an
internal, software trigger to set things up (allowing the user
application to write sufficient samples to the data buffer before the
trigger), so it acts as a software "pre-trigger" in the `TRIG_EXT` case.
The software trigger is handled by `ni_ao_inttrig()`.
Prior to the above change, when `start_src` was `TRIG_INT`, `start_arg`
was required to be 0, and `ni_ao_inttrig()` checked that the software
trigger number was also 0. After the above change, when `start_src` was
`TRIG_INT`, any value was allowed for `start_arg`, and `ni_ao_inttrig()`
checked that the software trigger number matched this `start_arg` value.
The backwards compatibility issue is that the internal trigger number
now has to match `start_arg` when `start_src` is `TRIG_EXT` when it
previously had to be 0.
Fix the backwards compatibility issue in `ni_ao_inttrig()` by always
allowing software trigger number 0 when `start_src` is something other
than `TRIG_INT`.
Thanks to Spencer Olson for reporting the issue.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Reported-by: Spencer Olson <olsonse@umich.edu>
Fixes: ebb657babf ("staging: comedi: ni_mio_common: clarify the cmd->start_arg validation and use")
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 80e162ee9b upstream.
`daqboard2000_find_boardinfo()` is supposed to check if the
DaqBoard/2000 series model is supported, based on the PCI subvendor and
subdevice ID. The current code is wrong as it is comparing the PCI
device's subdevice ID to an expected, fixed value for the subvendor ID.
It should be comparing the PCI device's subvendor ID to this fixed
value. Correct it.
Fixes: 7e8401b23e ("staging: comedi: daqboard2000: add back
subsystem_device check")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2c0f8ce1b5 upstream.
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB
adapters')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
