commit 32829da54d upstream.
A recent fix to /dev/mem prevents mappings from wrapping around the end
of physical address space. However, the check was written in a way that
also prevents a mapping reaching just up to the end of physical address
space, which may be a valid use case (especially on 32-bit systems).
This patch fixes it by checking the last mapped address (instead of the
first address behind that) for overflow.
Fixes: b299cde245 ("drivers: char: mem: Check for address space wraparound with mmap()")
Reported-by: Nico Huber <nico.h@gmx.de>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b299cde245 upstream.
/dev/mem currently allows mmap() mappings that wrap around the end of
the physical address space, which should probably be illegal. It
circumvents the existing STRICT_DEVMEM permission check because the loop
immediately terminates (as the start address is already higher than the
end address). On the x86_64 architecture it will then cause a panic
(from the BUG(start >= end) in arch/x86/mm/pat.c:reserve_memtype()).
This patch adds an explicit check to make sure offset + size will not
wrap around in the physical address type.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3e21f4af17 upstream.
The lp_setup() code doesn't apply any bounds checking when passing
"lp=none", and only in this case, resulting in an overflow of the
parport_nr[] array. All versions in Git history are affected.
Reported-By: Roee Hay <roee.hay@hcl.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a4866aa812 upstream.
Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is
disallowed. However, on x86, the first 1MB was always allowed for BIOS
and similar things, regardless of it actually being System RAM. It was
possible for heap to end up getting allocated in low 1MB RAM, and then
read by things like x86info or dd, which would trip hardened usercopy:
usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes)
This changes the x86 exception for the low 1MB by reading back zeros for
System RAM areas instead of blindly allowing them. More work is needed to
extend this to mmap, but currently mmap doesn't go through usercopy, so
hardened usercopy won't Oops the kernel.
Reported-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Tested-by: Tommi Rantala <tommi.t.rantala@nokia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2055997f98 upstream.
We try to disable callbacks on c_ivq even without multiport
even though that vq is not initialized in this configuration.
Fixes: c743d09dbd ("virtio: console: Disable callbacks for virtqueues at start of S4 freeze")
Suggested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c4baad5029 upstream.
put_chars() stuffs the buffer it gets into an sg, but that buffer may be
on the stack. This breaks with CONFIG_VMAP_STACK=y (for me, it
manifested as printks getting turned into NUL bytes).
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 34563769e4 upstream.
Commit c6017e793b ("virtio: console: add locks around buffer removal
in port unplug path") added locking around the freeing of buffers in the
vq. However, when free_buf() is called with can_sleep = true and rproc
is enabled, it calls dma_free_coherent() directly, requiring interrupts
to be enabled. Currently a WARNING is triggered due to the spin locking
around free_buf, with a call stack like this:
WARNING: CPU: 3 PID: 121 at ./include/linux/dma-mapping.h:433
free_buf+0x1a8/0x288
Call Trace:
[<8040c538>] show_stack+0x74/0xc0
[<80757240>] dump_stack+0xd0/0x110
[<80430d98>] __warn+0xfc/0x130
[<80430ee0>] warn_slowpath_null+0x2c/0x3c
[<807e7c6c>] free_buf+0x1a8/0x288
[<807ea590>] remove_port_data+0x50/0xac
[<807ea6a0>] unplug_port+0xb4/0x1bc
[<807ea858>] virtcons_remove+0xb0/0xfc
[<807b6734>] virtio_dev_remove+0x58/0xc0
[<807f918c>] __device_release_driver+0xac/0x134
[<807f924c>] device_release_driver+0x38/0x50
[<807f7edc>] bus_remove_device+0xfc/0x130
[<807f4b74>] device_del+0x17c/0x21c
[<807f4c38>] device_unregister+0x24/0x38
[<807b6b50>] unregister_virtio_device+0x28/0x44
Fix this by restructuring the loops to allow the locks to only be taken
where it is necessary to protect the vqs, and release it while the
buffer is being freed.
Fixes: c6017e793b ("virtio: console: add locks around buffer removal in port unplug path")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6d4952d9d9 upstream.
hw_random carefully avoids using a stack buffer except in
add_early_randomness(). This causes a crash in virtio_rng if
CONFIG_VMAP_STACK=y.
Reported-by: Matt Mullins <mmullins@mmlx.us>
Tested-by: Matt Mullins <mmullins@mmlx.us>
Fixes: d3cc799647 ("hwrng: fetch randomness only after device init")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9754d45e99 upstream.
Some chips incorrectly support partial reads from TPM_STS register
at non-zero offsets. Read the entire 32-bits register instead of
making two 8-bit reads to support such devices and reduce the number
of bus transactions when obtaining the burstcount from TPM_STS.
Fixes: 27084efee0 ("tpm: driver for next generation TPM chips")
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
[bwh: Backported to 3.16:
- Use raw ioread32() instead of tpm_tis_read32()
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 61dc0a446e upstream.
pm_runtime_get_sync does return a error value that must be checked for
error conditions, else, due to various reasons, the device maynot be
enabled and the system will crash due to lack of clock to the hardware
module.
Before:
12.562784] [00000000] *pgd=fe193835
12.562792] Internal error: : 1406 [#1] SMP ARM
[...]
12.562864] CPU: 1 PID: 241 Comm: modprobe Not tainted 4.7.0-rc4-next-20160624 #2
12.562867] Hardware name: Generic DRA74X (Flattened Device Tree)
12.562872] task: ed51f140 ti: ed44c000 task.ti: ed44c000
12.562886] PC is at omap4_rng_init+0x20/0x84 [omap_rng]
12.562899] LR is at set_current_rng+0xc0/0x154 [rng_core]
[...]
After the proper checks:
[ 94.366705] omap_rng 48090000.rng: _od_fail_runtime_resume: FIXME:
missing hwmod/omap_dev info
[ 94.375767] omap_rng 48090000.rng: Failed to runtime_get device -19
[ 94.382351] omap_rng 48090000.rng: initialization failed.
Fixes: 665d92fa85 ("hwrng: OMAP: convert to use runtime PM")
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4b44f2d18a upstream.
The Hyper-V Linux Integration Services use the VMBus implementation for
communication with the Hypervisor. VMBus registers its own interrupt
handler that completely bypasses the common Linux interrupt handling.
This implies that the interrupt entropy collector is not triggered.
This patch adds the interrupt entropy collection callback into the VMBus
interrupt handler function.
Signed-off-by: Stephan Mueller <stephan.mueller@atsec.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9b4d008787 upstream.
Since systemd is consistently using /dev/urandom before it is
initialized, we can't see the other potentially dangerous users of
/dev/urandom immediately after boot. So print the first ten such
complaints instead.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7613663cc1 upstream.
For security reasons ordinary user must not be able to control fan speed
via /proc/i8k by default. Some malicious software running under "nobody"
user could be able to turn fan off and cause HW problems. So this patch
changes default value of "restricted" parameter to 1.
Also restrict reading of DMI_PRODUCT_SERIAL from /proc/i8k via "restricted"
parameter. It is because non root user cannot read DMI_PRODUCT_SERIAL from
sysfs file /sys/class/dmi/id/product_serial.
Old non secure behaviour of file /proc/i8k can be achieved by loading this
module with "restricted" parameter set to 0.
Note that this patch has effects only for kernels compiled with CONFIG_I8K
and only for file /proc/i8k. Hwmon interface provided by this driver was
not changed and root access for setting fan speed was needed also before.
Reported-by: Mario Limonciello <Mario_Limonciello@dell.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 309124e264 upstream.
According to full-history-linux commit d3794f4fa7c3edc3 ("[PATCH] M68k
update (part 25)"), port operations are allowed on m68k if CONFIG_ISA is
defined.
However, commit 153dcc54df ("[PATCH] mem driver: fix conditional
on isa i/o support") accidentally changed an "||" into an "&&",
disabling it completely on m68k. This logic was retained when
introducing the DEVPORT symbol in commit 4f911d64e0 ("Make
/dev/port conditional on config symbol").
Drop the bogus dependency on !M68K to fix this.
Fixes: 153dcc54df ("[PATCH] mem driver: fix conditional on isa i/o support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 27f972d3e0 upstream.
We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.
static int smi_start_processing(void *send_info,
ipmi_smi_t intf)
{
/* Try to claim any interrupts. */
if (new_smi->irq_setup)
new_smi->irq_setup(new_smi);
--> IRQ arrives here and irq handler tries to modify uninitialized timer
which triggers BUG_ON(!timer->function) in __mod_timer().
Call Trace:
<IRQ>
[<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
[<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
[<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
[<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
[<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
[<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
[<ffffffff810f245e>] handle_edge_irq+0xde/0x180
[<ffffffff8100fc59>] handle_irq+0x49/0xa0
[<ffffffff8154643c>] do_IRQ+0x6c/0xf0
[<ffffffff8100ba53>] ret_from_intr+0x0/0x11
/* Set up the timer that drives the interface. */
setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);
The following patch fixes the problem.
To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb8ed1eb9a upstream.
Reference to the 'np' node is dropped before dereferencing the 'sizep' and
'basep' pointers, which could by then point to junk if the node has been
freed.
Refactor code to call 'of_node_put' later.
Fixes: c5df39262d ("drivers/char/tpm: Add securityfs support for event log")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Peter Huewe <PeterHuewe@gmx.de>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 60ecd86c4d upstream.
At ibm vtpm initialzation, tpm_ibmvtpm_probe() registers its interrupt
handler, ibmvtpm_interrupt, which calls ibmvtpm_crq_process to allocate
memory for rtce buffer. The current code uses 'GFP_KERNEL' as the
type of kernel memory allocation, which resulted a warning at
kernel/lockdep.c. This patch uses 'GFP_ATOMIC' instead so that the
allocation is high-priority and does not sleep.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 8b572a4200 upstream.
In needs_ilk_vtd_wa(), we pass in the GPU device but compared it against
the ids for the mobile GPU and the mobile host bridge. That latter is
impossible and so likely was just a typo for the desktop GPU device id
(which is also buggy).
Fixes commit da88a5f7f7
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Feb 13 09:31:53 2013 +0000
drm/i915: Disable WC PTE updates to w/a buggy IOMMU on ILK
Reported-by: Ting-Wei Lan <lantw44@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91127
References: https://bugzilla.freedesktop.org/show_bug.cgi?id=60391
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 9d75f08946 upstream.
tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet
set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq,
the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Fixes: 132f762947 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eeb8a7e8bb upstream.
when multiport is off, virtio console invokes config access from irq
context, config access is blocking on s390.
Fix this up by scheduling work from config irq - similar to what we do
for multiport configs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4f6e24ed9d upstream.
when multiport is off, we don't initialize config work,
but we then cancel uninitialized control_work on freeze.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 62dfd912ab upstream.
Problem: When IMA and VTPM are both enabled in kernel config,
kernel hangs during bootup on LE OS.
Why?: IMA calls tpm_pcr_read() which results in tpm_ibmvtpm_send
and tpm_ibmtpm_recv getting called. A trace showed that
tpm_ibmtpm_recv was hanging.
Resolution: tpm_ibmtpm_recv was hanging because tpm_ibmvtpm_send
was sending CRQ message that probably did not make much sense
to phype because of Endianness. The fix below sends correctly
converted CRQ for LE. This was not caught before because it
seems IMA is not enabled by default in kernel config and
IMA exercises this particular code path in vtpm.
Tested with IMA and VTPM enabled in kernel config and VTPM
enabled on both a BE OS and a LE OS ppc64 lpar. This exercised
CRQ and TPM command code paths in vtpm.
Patch is against Peter's tpmdd tree on github which included
Vicky's previous vtpm le patches.
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eb71f8a5e3 upstream.
The tpm_ibmvtpm module is affected by an unaligned access problem.
ibmvtpm_crq_get_version failed with rc=-4 during boot when vTPM is
enabled in Power partition, which supports both little endian and
big endian modes.
We added little endian support to fix this problem:
1) added cpu_to_be64 calls to ensure BE data is sent from an LE OS.
2) added be16_to_cpu and be32_to_cpu calls to make sure data received
is in LE format on a LE OS.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com>
[phuewe: manually applied the patch :( ]
Reviewed-by: Ashley Lai <ashley@ahsleylai.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c4eadfafb9 upstream.
Add a return value check when reading data from the FIFO register.
Reviewed-by: Jason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 1ba3b0b6f2 upstream.
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 84eb186bc3 upstream.
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 448e9c55c1 upstream.
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bb95cd34ba upstream.
Currently these driver are missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 398a1e71dc upstream.
Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed. Adding a second device would break IMA, for
instance.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 24c65bc703 upstream.
The add_early_randomness() function in drivers/char/hw_random/core.c passes
a 16-byte buffer to pseries_rng_data_read(). Unfortunately, plpar_hcall()
returns four 64-bit values and trashes 16 bytes on the stack.
This bug has been lying around for a long time. It got unveiled by:
commit d3cc799647
Author: Amit Shah <amit.shah@redhat.com>
Date: Thu Jul 10 15:42:34 2014 +0530
hwrng: fetch randomness only after device init
It may trig a oops while loading or unloading the pseries-rng module for both
PowerVM and PowerKVM guests.
This patch does two things:
- pass an intermediate well sized buffer to plpar_hcall(). This is acceptalbe
since we're not on a hot path.
- move to the new read API so that we know the return buffer size for sure.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit f49819560f upstream.
Before we really unregister the hwrng device, reading will get stuck if
the virtio device is reset. We should return error for reading when we
start to remove the device.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 3856e54837 upstream.
When we try to hot-remove a busy virtio-rng device from QEMU monitor,
the device can't be hot-removed. Because virtio-rng driver hangs at
wait_for_completion_killable().
This patch exits the waiting by completing have_data completion before
unregistering, resets data_avail to avoid the hwrng core use wrong
buffer bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d4c5efdb97 upstream.
zatimend has reported that in his environment (3.16/gcc4.8.3/corei7)
memset() calls which clear out sensitive data in extract_{buf,entropy,
entropy_user}() in random driver are being optimized away by gcc.
Add a helper memzero_explicit() (similarly as explicit_bzero() variants)
that can be used in such cases where a variable with sensitive data is
being cleared out in the end. Other use cases might also be in crypto
code. [ I have put this into lib/string.c though, as it's always built-in
and doesn't need any dependencies then. ]
Fixes kernel bugzilla: 82041
Reported-by: zatimend@hotmail.co.uk
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[ kamal: backport to 3.13-stable: one more memzero_explicit in extract_buf() ]
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit eeec626366 upstream.
This reverts commit e052dbf554.
Now that we use the virtio ->scan() function to register with the hwrng
core, we will not get read requests till probe is successfully finished.
So revert the workaround we had in place to refuse read requests while
we were not yet setup completely.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c06273401 upstream.
Instead of calling hwrng_register() in the probe routing, call it in the
scan routine. This ensures that when hwrng_register() is successful,
and it requests a few random bytes to seed the kernel's pool at init,
we're ready to service that request.
This will also enable us to remove the workaround added previously to
check whether probe was completed, and only then ask for data from the
host. The revert follows in the next commit.
There's a slight behaviour change here on unsuccessful hwrng_register().
Previously, when hwrng_register() failed, the probe() routine would
fail, and the vqs would be torn down, and driver would be marked not
initialized. Now, the vqs will remain initialized, driver would be
marked initialized as well, but won't be available in the list of RNGs
available to hwrng core. To fix the failures, the procedure remains the
same, i.e. unload and re-load the module, and hope things succeed the
next time around.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e54caf407 upstream.
Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels]
Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
commit 3e14d83ef9 upstream.
Regression in 41ab999c. Call to tpm_chip_put is missing. This
will cause TPM device driver not to unload if tmp_get_random()
is called.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f07a5e9a33 upstream.
Most device drivers do call 'tpm_do_selftest' which executes a
TPM_ContinueSelfTest. tpm_i2c_stm_st33 is just pointlessly different,
I think it is bug.
These days we have the general assumption that the TPM is usable by
the kernel immediately after the driver is finished, so we can no
longer defer the mandatory self test to userspace.
Reported-by: Richard Marciel <rmaciel@linux.vnet.ibm.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJTygXeAAoJENNvdpvBGATwBVYP/3OHIb58JhHjC/GbHKhe0UdX
eSBle+8bcDdwADXBQ2Slzp7bVBwBHaEgKOz0Y9iTObrICb5orUGtB7MmGi9b9WIW
8igTkvNhQxwNZat89U5SOpPuwSJEyR9LeIKN8JG75j+ymX/H1vjsojJcXxfZzYT0
qoiUs32VbmglfVPy1WvPLZ/0fYtaRwzE6des7yzZHYbEvgX5JIJ7m4sQftMj4a+L
CNiLHXLijsUX9CG94Gjw7R7/PLK83UNM+ER5zUTIC6EqRJCZVIQAU0zvyE5sm3ZK
v3n8aJypZZhNBGJm4SNWlwsbwllx9BvPOq2DadY+/Jpzqrxy1saYB+XoKKdT3t2Y
3OJb/eh02wuCzCzJgNNP9CJhdPV7h4qrg5M1OqrBsFgXEAlISLvWEM+//FB8Hsmv
NDKeWl6Y5Iy6UCZDVQpuYCJTo46ACt0DBLpOE9tXDtz6yuLF+Hs3GmRPz368EcEy
t98UmU7mS447FQdqjThKdH1g/ZeGepXDMkk/hosmnck7OgQzuLMBnAagwouQ9YSH
O32MyvGHkAPEL2SB2WzGdWIHr/K2EWiyAoO3OVaUrJ7tVrGvVig/WsgYyNaHzBlp
5VRCdBXJ78tH+KYl0lIkrzrOnd1AegQtIIH5E3iZsdUVqCM/DdDd5ewwWxC7Ar3s
PGrT4lp8vqIT0H3D65a5
=8rgT
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"Fix a BUG splat found by trinity"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: check for increase of entropy_count because of signed conversion
Pull crypto fixes from Herbert Xu:
"This push fixes a boot hang in virt guests when the virtio RNG is
enabled"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: virtio - ensure reads happen after successful probe
hwrng: fetch randomness only after device init
The expression entropy_count -= ibytes << (ENTROPY_SHIFT + 3) could
actually increase entropy_count if during assignment of the unsigned
expression on the RHS (mind the -=) we reduce the value modulo
2^width(int) and assign it to entropy_count. Trinity found this.
[ Commit modified by tytso to add an additional safety check for a
negative entropy_count -- which should never happen, and to also add
an additional paranoia check to prevent overly large count values to
be passed into urandom_read(). ]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
The hwrng core asks for random data in the hwrng_register() call itself
from commit d9e7972619. This doesn't play well with virtio -- the
DRIVER_OK bit is only set by virtio core on a successful probe, and
we're not yet out of our probe routine when this call is made. This
causes the host to not acknowledge any requests we put in the virtqueue,
and the insmod or kernel boot process just waits for data to arrive from
the host, which never happens.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit d9e7972619 "hwrng: add randomness to system from rng sources"
added a call to rng_get_data() from the hwrng_register() function.
However, some rng devices need initialization before data can be read
from them.
This commit makes the call to rng_get_data() depend on no init fn
pointer being registered by the device. If an init function is
registered, this call is made after device init.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit f36fdb9f02 (i8k: Force SMM to run on CPU 0) adds support
for multi-core CPUs to the driver. Unfortunately, that causes it
to fail loading if compiled without SMP support, at least on
32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell
signature", and function i8k_smm is found to return -EINVAL.
Testing revealed that the culprit is the missing return value check
of set_cpus_allowed_ptr.
Fixes: f36fdb9f02 (i8k: Force SMM to run on CPU 0)
Reported-by: Jim Bos <jim876@xs4all.nl>
Tested-by: Jim Bos <jim876@xs4all.nl>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0fb7a01af5 "random: simplify accounting code", introduced in
v3.15, has a very nasty accounting problem when the entropy pool has
has fewer bytes of entropy than the number of requested reserved
bytes. In that case, "have_bytes - reserved" goes negative, and since
size_t is unsigned, the expression:
ibytes = min_t(size_t, ibytes, have_bytes - reserved);
... does not do the right thing. This is rather bad, because it
defeats the catastrophic reseeding feature in the
xfer_secondary_pool() path.
It also can cause the "BUG: spinlock trylock failure on UP" for some
kernel configurations when prandom_reseed() calls get_random_bytes()
in the early init, since when the entropy count gets corrupted,
credit_entropy_bits() erroneously believes that the nonblocking pool
has been fully initialized (when in fact it is not), and so it calls
prandom_reseed(true) recursively leading to the spinlock BUG.
The logic is *not* the same it was originally, but in the cases where
it matters, the behavior is the same, and the resulting code is
hopefully easier to read and understand.
Fixes: 0fb7a01af5 "random: simplify accounting code"
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Greg Price <price@mit.edu>
Cc: stable@vger.kernel.org #v3.15
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
path, which I refuse to CC stable since (1) I discovered it myself, and
(2) it's been there forever with no reports.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YCNa
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Main excitement is a virtio_scsi fix for alloc holding spinlock on the
abort path, which I refuse to CC stable since (1) I discovered it
myself, and (2) it's been there forever with no reports"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: don't call virtqueue_add_sgs(... GFP_NOIO) holding spinlock.
virtio-rng: fixes for device registration/unregistration
virtio-rng: fix boot with virtio-rng device
virtio-rng: support multiple virtio-rng devices
virtio_ccw: introduce device_lost in virtio_ccw_device
virtio: virtio_break_device() to mark all virtqueues broken.
