commit ddff7ed45e upstream.
When pci_enable_device() or pci_enable_device_mem() fail in
qla2x00_probe_one() we bail out but do a call to
pci_disable_device(). This causes the dev_WARN_ON() in
pci_disable_device() to trigger, as the device wasn't enabled
previously.
So instead of taking the 'probe_out' error path we can directly return
*iff* one of the pci_enable_device() calls fails.
Additionally rename the 'probe_out' goto label's name to the more
descriptive 'disable_device'.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: e315cd28b9 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7a38dc0bfb upstream.
The current medium access timeout counter will be increased for
each command, so if there are enough failed commands we'll hit
the medium access timeout for even a single device failure and
the following kernel message is displayed:
sd H:C:T:L: [sdXY] Medium access timeout failure. Offlining disk!
Fix this by making the timeout per EH run, ie the counter will
only be increased once per device and EH run.
Fixes: 18a4d0a ("[SCSI] Handle disk devices which can not process medium access commands")
Cc: Ewan Milne <emilne@redhat.com>
Cc: Lawrence Obermann <loberman@redhat.com>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16:
- Open-code blk_rq_is_passthrough()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7c856152cb upstream.
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Reported-by: Steve Magnani <steve.magnani@digidescorp.com>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a00a786251 upstream.
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9702c67c60 upstream.
The total ata xfer length may not be calculated properly, in that we do
not use the proper method to get an sg element dma length.
According to the code comment, sg_dma_len() should be used after
dma_map_sg() is called.
This issue was found by turning on the SMMUv3 in front of the hisi_sas
controller in hip07. Multiple sg elements were being combined into a
single element, but the original first element length was being use as
the total xfer length.
Fixes: ff2aeb1eb6 ("libata: convert to chained sg")
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 85e8a23936 upstream.
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 934767c56b upstream.
The return status of the adapter check on KERNEL_PANIC is supposed to be
the upper 16 bits of the OMR status register.
Fixes: c421530bf8 (scsi: aacraid: Reorder Adpater status check)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6f8830f5bb upstream.
There's a rather long standing regression from the commit "libiscsi:
Reduce locking contention in fast path"
Depending on iSCSI target behavior, it's possible to hit the case in
iscsi_complete_task where the task is still on a pending list
(!list_empty(&task->running)). When that happens the task is removed
from the list while holding the session back_lock, but other task list
modification occur under the frwd_lock. That leads to linked list
corruption and eventually a panicked system.
Rather than back out the session lock split entirely, in order to try
and keep some of the performance gains this patch adds another lock to
maintain the task lists integrity.
Major enterprise supported kernels have been backing out the lock split
for while now, thanks to the efforts at IBM where a lab setup has the
most reliable reproducer I've seen on this issue. This patch has been
tested there successfully.
Signed-off-by: Chris Leech <cleech@redhat.com>
Fixes: 659743b02c ("[SCSI] libiscsi: Reduce locking contention in fast path")
Reported-by: Prashantha Subbarao <psubbara@us.ibm.com>
Reviewed-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c421530bf8 upstream.
The driver currently checks the SELF_TEST_FAILED first and then
KERNEL_PANIC next. Under error conditions(boot code failure) both
SELF_TEST_FAILED and KERNEL_PANIC can be set at the same time.
The driver has the capability to reset the controller on an KERNEL_PANIC,
but not on SELF_TEST_FAILED.
Fixed by first checking KERNEL_PANIC and then the others.
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC base controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1bff5abca6 upstream.
aac_fib_map_free frees misaligned fib dma memory, additionally it does not
free up the whole memory.
Fixed by changing the code to free up the correct and full memory
allocation.
Fixes: e8b12f0fb8 ([SCSI] aacraid: Add new code for PMC-Sierra's SRC based controller family)
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: David Carroll <David.Carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: s/max_cmd_size/max_fib_size/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 40630f4628 upstream.
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com>
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bba5dc332e upstream.
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3209f9d780 upstream.
SRB status can have additional information. Mask these out before processing
SRB status.
This patch was sent as part of a collection of patches more than a year ago.
While the rest of the patches in the set were comitted, this patch was not.
I woulod like to thank Olaf for noticing that this patch was not committed
upstream.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3cd6d3d9b1 upstream.
Properly set SRB flags when hosting device supports tagged queuing.
This patch improves the performance on Fiber Channel disks.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 137d01df51 upstream.
What happens is that a write to /dev/sg is given a request with non-zero
->iovec_count combined with zero ->dxfer_len. Or with ->dxferp pointing
to an array full of empty iovecs.
Having write permission to /dev/sg shouldn't be equivalent to the
ability to trigger BUG_ON() while holding spinlocks...
Found by Dmitry Vyukov and syzkaller.
[ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the
underlying issue. - Linus ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: we're not using iov_iter, but can check the
byte length after truncation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fc1ffd6cb3 upstream.
During code inspection, while investigating following stack trace
seen on one of the test setup, we found out there was possibility
of memory leak becuase driver was not unwinding the stack properly.
This issue has not been reproduced in a test environment or on a
customer setup.
Here's stack trace that was seen.
[1469877.797315] Call Trace:
[1469877.799940] [<ffffffffa03ab6e9>] qla2x00_mem_alloc+0xb09/0x10c0 [qla2xxx]
[1469877.806980] [<ffffffffa03ac50a>] qla2x00_probe_one+0x86a/0x1b50 [qla2xxx]
[1469877.814013] [<ffffffff813b6d01>] ? __pm_runtime_resume+0x51/0xa0
[1469877.820265] [<ffffffff8157c1f5>] ? _raw_spin_lock_irqsave+0x25/0x90
[1469877.826776] [<ffffffff8157cd2d>] ? _raw_spin_unlock_irqrestore+0x6d/0x80
[1469877.833720] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.839885] [<ffffffff8157cd0c>] ? _raw_spin_unlock_irqrestore+0x4c/0x80
[1469877.846830] [<ffffffff81319b9c>] local_pci_probe+0x4c/0xb0
[1469877.852562] [<ffffffff810741d1>] ? preempt_count_sub+0xb1/0x100
[1469877.858727] [<ffffffff81319c89>] pci_call_probe+0x89/0xb0
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d2a145252c upstream.
A race between scanning and fc_remote_port_delete() may result in a
permanent stop if the device gets blocked before scsi_sysfs_add_sdev()
and unblocked after. The reason is that blocking a device sets both the
SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However,
scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the
device to be ignored by scsi_target_unblock() and thus never have its
QUEUE_FLAG_STOPPED cleared leading to a device which is apparently
running but has a stopped queue.
We actually have two places where SDEV_RUNNING is set: once in
scsi_add_lun() which respects the blocked flag and once in
scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely
spurious, simply remove it to fix the problem.
Reported-by: Zengxi Chen <chenzengxi@huawei.com>
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit af15769ffa upstream.
gcc-7 notices that the condition in mvs_94xx_command_active looks
suspicious:
drivers/scsi/mvsas/mv_94xx.c: In function 'mvs_94xx_command_active':
drivers/scsi/mvsas/mv_94xx.c:671:15: error: '<<' in boolean context, did you mean '<' ? [-Werror=int-in-bool-context]
This was introduced when the mv_printk() statement got added, and leads
to the condition being ignored. This is probably harmless.
Changing '&&' to '&' makes the code look reasonable, as we check the
command bit before setting and printing it.
Fixes: a4632aae8b ("[SCSI] mvsas: Add new macros and functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 18e1c7f68a upstream.
For SRIOV enabled firmware, if there is a OCR(online controller reset)
possibility driver set the convert flag to 1, which is not happening if
there are outstanding commands even after 180 seconds. As driver does
not set convert flag to 1 and still making the OCR to run, VF(Virtual
function) driver is directly writing on to the register instead of
waiting for 30 seconds. Setting convert flag to 1 will cause VF driver
will wait for 30 secs before going for reset.
Signed-off-by: Kiran Kumar Kasturi <kiran-kumar.kasturi@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 128394eff3 upstream.
Both damn things interpret userland pointers embedded into the payload;
worse, they are actually traversing those. Leaving aside the bad
API design, this is very much _not_ safe to call with KERNEL_DS.
Bail out early if that happens.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f3951a3709 upstream.
In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().
Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.
This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:
------------[ cut here ]------------
kernel BUG at block/blk-core.c:1420!
Call Trace:
[<ffffffff81281eab>] blk_put_request+0x5b/0x80
[<ffffffffa0069e5b>] sg_finish_rem_req+0x6b/0x120 [sg]
[<ffffffffa006bcb9>] sg_common_write.isra.14+0x459/0x5a0 [sg]
[<ffffffff8125b328>] ? selinux_file_alloc_security+0x48/0x70
[<ffffffffa006bf95>] sg_new_write.isra.17+0x195/0x2d0 [sg]
[<ffffffffa006cef4>] sg_ioctl+0x644/0xdb0 [sg]
[<ffffffff81170f80>] do_vfs_ioctl+0x90/0x520
[<ffffffff81258967>] ? file_has_perm+0x97/0xb0
[<ffffffff811714a1>] SyS_ioctl+0x91/0xb0
[<ffffffff81602afb>] tracesys+0xdd/0xe2
RIP [<ffffffff81281e04>] __blk_put_request+0x154/0x1a0
The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.
Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.
KASAN was extremely helpful in finding the root cause of this bug.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16:
- sg_finish_rem_req() would not free srp->rq->cmd so don't do it here either
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 18f6084a98 upstream.
This is a work around for a bug with LSI Fusion MPT SAS2 when perfoming
secure erase. Due to the very long time the operation takes, commands
issued during the erase will time out and will trigger execution of the
abort hook. Even though the abort hook is called for the specific
command which timed out, this leads to entire device halt
(scsi_state terminated) and premature termination of the secure erase.
Set device state to busy while ATA passthrough commands are in progress.
[mkp: hand applied to 4.9/scsi-fixes, tweaked patch description]
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: <linux-scsi@vger.kernel.org>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5e5ec1759d upstream.
This patch will fix regression caused by commit 1e793f6fc0 ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
[mkp: clarified patch description]
Fixes: 1e793f6fc0
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Tested-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2bf7dc8443 upstream.
The arcmsr driver failed to pass SYNCHRONIZE CACHE to controller
firmware. Depending on how drive caches are handled internally by
controller firmware this could potentially lead to data integrity
problems.
Ensure that cache flushes are passed to the controller.
[mkp: applied by hand and removed unused vars]
Signed-off-by: Ching Huang <ching2048@areca.com.tw>
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4d2b496f19 upstream.
map_storep was not being vfree()'d in the module_exit call.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1e793f6fc0 upstream.
Commit 02b01e010a ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010a
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 07d0e9a847 upstream.
If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ
init complete following H_REG_CRQ. If this occurs, we can end up having
called scsi_block_requests and not a resulting unblock until the init
complete happens, which may never occur, and we end up hanging I/O
requests. This patch ensures the host action stay set to
IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and
unblock unless we receive an init complete.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7bc2b55a5c upstream.
We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16:
- Adjust context
- Use literal 1032 insetad of ARCMSR_API_DATA_BUFLEN]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a87eeb900d upstream.
Commit 655ee63cf3 ("scsi constants: command, sense key + additional
sense string") added a "Completed" sense string with key 0xF to
snstext[], but failed to updated the upper bounds check of the sense key
in scsi_sense_key_string().
Fixes: 655ee63cf3 ("[SCSI] scsi constants: command, sense key + additional sense strings")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e7f851684e upstream.
Found one megaraid_sas HBA probe fails,
[ 187.235190] scsi host2: Avago SAS based MegaRAID driver
[ 191.112365] megaraid_sas 0000:89:00.0: BAR 0: can't reserve [io 0x0000-0x00ff]
[ 191.120548] megaraid_sas 0000:89:00.0: IO memory region busy!
and the card has resource like,
[ 125.097714] pci 0000:89:00.0: [1000:005d] type 00 class 0x010400
[ 125.104446] pci 0000:89:00.0: reg 0x10: [io 0x0000-0x00ff]
[ 125.110686] pci 0000:89:00.0: reg 0x14: [mem 0xce400000-0xce40ffff 64bit]
[ 125.118286] pci 0000:89:00.0: reg 0x1c: [mem 0xce300000-0xce3fffff 64bit]
[ 125.125891] pci 0000:89:00.0: reg 0x30: [mem 0xce200000-0xce2fffff pref]
that does not io port resource allocated from BIOS, and kernel can not
assign one as io port shortage.
The driver is only looking for MEM, and should not fail.
It turns out megasas_init_fw() etc are using bar index as mask. index 1
is used as mask 1, so that pci_request_selected_regions() is trying to
request BAR0 instead of BAR1.
Fix all related reference.
Fixes: b6d5d8808b ("megaraid_sas: Use lowest memory bar for SR-IOV VF support")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fa00c437ee upstream.
In aacraid's ioctl_send_fib() we do two fetches from userspace, one the
get the fib header's size and one for the fib itself. Later we use the
size field from the second fetch to further process the fib. If for some
reason the size from the second fetch is different than from the first
fix, we may encounter an out-of- bounds access in aac_fib_send(). We
also check the sender size to insure it is not out of bounds. This was
reported in https://bugzilla.kernel.org/show_bug.cgi?id=116751 and was
assigned CVE-2016-6480.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: 7c00ffa31 '[SCSI] 2.6 aacraid: Variable FIB size (updated patch)'
Signed-off-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 54e430bbd4 upstream.
If we fall back to using LSI on the Croc or Crocodile chip we need to
clear the interrupt so we don't hang the system.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 72d8c36ec3 upstream.
sas_ata_strategy_handler() adds the works of the ata error handler to
system_unbound_wq. This workqueue asynchronously runs work items, so the
ata error handler will be performed concurrently on different CPUs. In
this case, ->host_failed will be decreased simultaneously in
scsi_eh_finish_cmd() on different CPUs, and become abnormal.
It will lead to permanently inequality between ->host_failed and
->host_busy, and scsi error handler thread won't start running. IO
errors after that won't be handled.
Since all scmds must have been handled in the strategy handler, just
remove the decrement in scsi_eh_finish_cmd() and zero ->host_busy after
the strategy handler to fix this race.
Fixes: 50824d6c56 ("[SCSI] libsas: async ata-eh")
Signed-off-by: Wei Fang <fangwei1@huawei.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a621bac304 upstream.
When SCSI was written, all commands coming from the filesystem
(REQ_TYPE_FS commands) had data. This meant that our signal for needing
to complete the command was the number of bytes completed being equal to
the number of bytes in the request. Unfortunately, with the advent of
flush barriers, we can now get zero length REQ_TYPE_FS commands, which
confuse this logic because they satisfy the condition every time. This
means they never get retried even for retryable conditions, like UNIT
ATTENTION because we complete them early assuming they're done. Fix
this by special casing the early completion condition to recognise zero
length commands with errors and let them drop through to the retry code.
Reported-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Tested-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fc4bf75ea3 upstream.
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 07beca2be2 upstream.
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()"
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 305c2e71b3 upstream.
Now that we've done a more comprehensive fix with the intermediate
target state we can remove the previous hack introduced with commit
90a88d6ef8 ("scsi: fix soft lockup in scsi_remove_target() on module
removal").
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f05795d3d7 upstream.
Add intermediate STARGET_REMOVE state to scsi_target_state to avoid
running into the BUG_ON() in scsi_target_reap(). The STARGET_REMOVE
state is only valid in the path from scsi_remove_target() to
scsi_target_destroy() indicating this target is going to be removed.
This re-fixes the problem introduced in commits bc3f02a795 ("[SCSI]
scsi_remove_target: fix softlockup regression on hot remove") and
4099819356 ("scsi: restart list search after unlock in
scsi_remove_target") in a more comprehensive way.
[mkp: Included James' fix for scsi_target_destroy()]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 4099819356
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Bottomley <jejb@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f08bb1e0db upstream.
During revalidate we check whether device capacity has changed before we
decide whether to output disk information or not.
The check for old capacity failed to take into account that we scaled
sdkp->capacity based on the reported logical block size. And therefore
the capacity test would always fail for devices with sectors bigger than
512 bytes and we would print several copies of the same discovery
information.
Avoid scaling sdkp->capacity and instead adjust the value on the fly
when setting the block device capacity and generating fake C/H/S
geometry.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16:
- logical_to_sectors() is a new function
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit aeb6641f8e upstream.
gcc-6 complains about the indentation of the lpfc_destroy_vport_work_array()
call in lpfc_online(), which clearly doesn't look right:
drivers/scsi/lpfc/lpfc_init.c: In function 'lpfc_online':
drivers/scsi/lpfc/lpfc_init.c:2880:3: warning: statement is indented as if it were guarded by... [-Wmisleading-indentation]
lpfc_destroy_vport_work_array(phba, vports);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/lpfc/lpfc_init.c:2863:2: note: ...this 'if' clause, but it is not
if (vports != NULL)
^~
Looking at the patch that introduced this code, it's clear that the
behavior is correct and the indentation is wrong.
This fixes the indentation and adds curly braces around the previous
if() block for clarity, as that is most likely what caused the code
to be misindented in the first place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 549e55cd2a ("[SCSI] lpfc 8.2.2 : Fix locking around HBA's port_list")
Reviewed-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5ecee0a3ee upstream.
One of the strange things that the original sg driver did was let the
user provide both a data-out buffer (it followed the sg_header+cdb)
_and_ specify a reply length greater than zero. What happened was that
the user data-out buffer was copied into some kernel buffers and then
the mid level was told a read type operation would take place with the
data from the device overwriting the same kernel buffers. The user would
then read those kernel buffers back into the user space.
From what I can tell, the above action was broken by commit fad7f01e61
("sg: set dxferp to NULL for READ with the older SG interface") in 2008
and syzkaller found that out recently.
Make sure that a user space pointer is passed through when data follows
the sg_header structure and command. Fix the abnormal case when a
non-zero reply_len is also given.
Fixes: fad7f01e61
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 84bd64993f upstream.
In beiscsi_setup_boot_info(), the boot_kset pointer should be set to
NULL in case of failure otherwise an invalid pointer dereference may
occur later.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f88fa79a61 upstream.
aac_fib_map_free() calls pci_free_consistent() without checking that
dev->hw_fib_va is not NULL and dev->max_fib_size is not zero.If they are
indeed NULL/0, this will result in a hang as pci_free_consistent() will
attempt to invalidate cache for the entire 64-bit address space
(which would take a very long time).
Fixed by adding a check to make sure that dev->hw_fib_va and
dev->max_fib_size are not NULL and 0 respectively.
Fixes: 9ad5204d6 - "[SCSI]aacraid: incorrect dma mapping mask during blinked recover or user initiated reset"
Signed-off-by: Raghava Aditya Renukunta <raghavaaditya.renukunta@pmcs.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 21b81716c6 upstream.
Commit d63c7dd5bc ("ipr: Fix out-of-bounds null overwrite") removed
the end of line handling when storing the update_fw sysfs attribute.
This changed the userpace API because it started refusing writes
terminated by a line feed, which broke the update tools we already have.
This patch re-adds that handling, so both a write terminated by a line
feed or not can make it through with the update.
Fixes: d63c7dd5bc ("ipr: Fix out-of-bounds null overwrite")
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Insu Yun <wuninsu@gmail.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d63c7dd5bc upstream.
Return value of snprintf is not bound by size value, 2nd argument.
(https://www.kernel.org/doc/htmldocs/kernel-api/API-snprintf.html).
Return value is number of printed chars, can be larger than 2nd
argument. Therefore, it can write null byte out of bounds ofbuffer.
Since snprintf puts null, it does not need to put additional null byte.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 82c4331050 upstream.
I have a Marvell 88SE9230 SATA Controller that has some sort of
integrated console SCSI device attached to one of the ports.
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: ATAPI: MARVELL VIRTUALL, 1.09, max UDMA/66
ata14.00: configured for UDMA/66
scsi 13:0:0:0: Processor Marvell Console 1.01 PQ: 0 ANSI: 5
Sending it VPD INQUIRY command seem to always fail with following error:
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 2 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
ata14: hard resetting link
This has been minor annoyance (only error printed on dmesg) until commit
09e2b0b146 ("scsi: rescan VPD attributes") added call to scsi_attach_vpd()
in scsi_rescan_device(). The commit causes the system to splat out
following errors continuously without ever reaching the UI:
ata14.00: configured for UDMA/66
ata14: EH complete
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 6 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
ata14: hard resetting link
ata14: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata14.00: configured for UDMA/66
ata14: EH complete
ata14.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
ata14.00: irq_stat 0x40000001
ata14.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 7 dma 16640 in
Inquiry 12 01 00 00 ff 00res 00/00:00:00:00:00/00:00:00:00:00/00 Emask 0x3 (HSM violation)
Without in-depth understanding of SCSI layer and the Marvell controller,
I suspect this happens because when the link goes down (because of an
error) we schedule scsi_rescan_device() which again fails to read VPD
data... ad infinitum.
Since VPD data cannot be read from the device anyway we prevent the SCSI
layer from even trying by blacklisting the device. This gets away the
error and the system starts up normally.
[mkp: Widened the match to all revisions of this device]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d2d06d4fe0 upstream.
If MODE SELECT returns with sense '05/91/36' (command lock violation)
it should always be retried without counting the number of retries.
During an HBA upgrade or similar circumstances one might see a flood
of MODE SELECT command from various HBAs, which will easily trigger
the sense code and exceed the retry count.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
