My backport of commit 2e63ad4bd5 "x86/apic: Do not init irq
remapping if ioapic is disabled" added an unconditional use of
skip_ioapic_setup. Enabling X86_LOCAL_APIC but not X86_IO_APIC
results in a build failure.
This configuration was made impossible by commit b1da1e715d
"x86/Kconfig: Simplify X86_IO_APIC dependencies", but that seems to
depend on additional changes that aren't suitable for stable.
The function that was changed, enable_IR_x2apic(), is only used in
64-bit configurations where CONFIG_X86_IO_APIC is always enabled. So
extend the #ifdef CONFIG_X86_64 section to include this function.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2bd7bc254a upstream.
This silences warnings like the following one when building with the
latest binutils:
arch/mips/kernel/genex.S: Assembler messages:
arch/mips/kernel/genex.S:438: Warning: the `msa' extension requires 64-bit FPRs
[ralf@linux-mips.org: Markos says binutils 2.25 and some 2.24 snapshots
are affected.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9745/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d19279154b upstream.
We should always use linux/types.h instead of asm/types.h for
consistency, and Kbuild actually warns about it:
./usr/include/asm/kvm.h:35: include of <linux/types.h> is preferred over <asm/types.h>
This patch does as Kbuild asks us.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit be5136988e upstream.
There are certain places where the code uses .set mips32 or .set mips64
or .set arch=r4000. In preparation of MIPS R6 support, and in order to
use as less #ifdefs as possible, we define new macros to set similar
annotations for MIPS R6.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
[bwh: Backported to 3.16: We don't support MIPS R6 but I have applied a
commit that uses MIPS_ISA_LEVEL_RAW. Add the R2 definitions only.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit efdab99281 upstream.
syzkaller reported:
WARNING: CPU: 0 PID: 12927 at arch/x86/kernel/traps.c:780 do_debug+0x222/0x250
CPU: 0 PID: 12927 Comm: syz-executor Tainted: G OE 4.15.0-rc2+ #16
RIP: 0010:do_debug+0x222/0x250
Call Trace:
<#DB>
debug+0x3e/0x70
RIP: 0010:copy_user_enhanced_fast_string+0x10/0x20
</#DB>
_copy_from_user+0x5b/0x90
SyS_timer_create+0x33/0x80
entry_SYSCALL_64_fastpath+0x23/0x9a
The testcase sets a watchpoint (with perf_event_open) on a buffer that is
passed to timer_create() as the struct sigevent argument. In timer_create(),
copy_from_user()'s rep movsb triggers the BP. The testcase also sets
the debug registers for the guest.
However, KVM only restores host debug registers when the host has active
watchpoints, which triggers a race condition when running the testcase with
multiple threads. The guest's DR6.BS bit can escape to the host before
another thread invokes timer_create(), and do_debug() complains.
The fix is to respect do_debug()'s dr6 invariant when leaving KVM.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fbdb328c6b upstream.
commit b3b7c4795c ("x86/MCE: Serialize sysfs changes") introduced a min
interval limitation when setting the check interval for polled MCEs.
However, the logic is that 0 disables polling for corrected MCEs, see
Documentation/x86/x86_64/machinecheck. The limitation prevents disabling.
Remove this limitation and allow the value 0 to disable polling again.
Fixes: b3b7c4795c ("x86/MCE: Serialize sysfs changes")
Signed-off-by: Dewet Thibaut <thibaut.dewet@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[ Massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180716084927.24869-1-alexander.sverdlin@nokia.com
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 38c0a74fe0 upstream.
The MIPS implementation of pci_resource_to_user() introduced in v3.12 by
commit 4c2924b725 ("MIPS: PCI: Use pci_resource_to_user to map pci
memory space properly") incorrectly sets *end to the address of the
byte after the resource, rather than the last byte of the resource.
This results in userland seeing resources as a byte larger than they
actually are, for example a 32 byte BAR will be reported by a tool such
as lspci as being 33 bytes in size:
Region 2: I/O ports at 1000 [disabled] [size=33]
Correct this by subtracting one from the calculated end address,
reporting the correct address to userland.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Rui Wang <rui.wang@windriver.com>
Fixes: 4c2924b725 ("MIPS: PCI: Use pci_resource_to_user to map pci memory space properly")
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19829/
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 93312b6da4 upstream.
mprotect(EXEC) was failing for stack mappings as default vm flags was
missing MAYEXEC.
This was triggered by glibc test suite nptl/tst-execstack testcase
What is surprising is that despite running LTP for years on, we didn't
catch this issue as it lacks a directed test case.
gcc dejagnu tests with nested functions also requiring exec stack work
fine though because they rely on the GNU_STACK segment spit out by
compiler and handled in kernel elf loader.
This glibc case is different as the stack is non exec to begin with and
a dlopen of shared lib with GNU_STACK segment triggers the exec stack
proceedings using a mprotect(PROT_EXEC) which was broken.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6e3761145a upstream.
swap was broken on ARC due to silly copy-paste issue.
We encode offset from swapcache page in __swp_entry() as (off << 13) but
were not decoding back in __swp_offset() as (off >> 13) - it was still
(off << 13).
This finally fixes swap usage on ARC.
| # mkswap /dev/sda2
|
| # swapon -a -e /dev/sda2
| Adding 500728k swap on /dev/sda2. Priority:-2 extents:1 across:500728k
|
| # free
| total used free shared buffers cached
| Mem: 765104 13456 751648 4736 8 4736
| -/+ buffers/cache: 8712 756392
| Swap: 500728 0 500728
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 612bc3b3d4 upstream.
On AMD, the presence of the MSR_SPEC_CTRL feature does not imply that the
SSBD mitigation support should use the SPEC_CTRL MSR. Other features could
have caused the MSR_SPEC_CTRL feature to be set, while a different SSBD
mitigation option is in place.
Update the SSBD support to check for the actual SSBD features that will
use the SPEC_CTRL MSR.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6ac2f49edb ("x86/bugs: Add AMD's SPEC_CTRL MSR usage")
Link: http://lkml.kernel.org/r/20180702213602.29202.33151.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 108fab4b5c upstream.
Both AMD and Intel can have SPEC_CTRL_MSR for SSBD.
However AMD also has two more other ways of doing it - which
are !SPEC_CTRL MSR ways.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: kvm@vger.kernel.org
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: andrew.cooper3@citrix.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180601145921.9500-4-konrad.wilk@oracle.com
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6ac2f49edb upstream.
The AMD document outlining the SSBD handling
124441_AMD64_SpeculativeStoreBypassDisable_Whitepaper_final.pdf
mentions that if CPUID 8000_0008.EBX[24] is set we should be using
the SPEC_CTRL MSR (0x48) over the VIRT SPEC_CTRL MSR (0xC001_011f)
for speculative store bypass disable.
This in effect means we should clear the X86_FEATURE_VIRT_SSBD
flag so that we would prefer the SPEC_CTRL MSR.
See the document titled:
124441_AMD64_SpeculativeStoreBypassDisable_Whitepaper_final.pdf
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199889
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: kvm@vger.kernel.org
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: andrew.cooper3@citrix.com
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Kees Cook <keescook@chromium.org>
Link: https://lkml.kernel.org/r/20180601145921.9500-3-konrad.wilk@oracle.com
[bwh: Backported to 3.16:
- The feature bit is in feature word 11
- Update feature test in guest_cpuid_has_spec_ctrl() instead of
svm_{get,set}_msr()
- Adjust filenames, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2480986001 upstream.
The AMD document outlining the SSBD handling
124441_AMD64_SpeculativeStoreBypassDisable_Whitepaper_final.pdf
mentions that the CPUID 8000_0008.EBX[26] will mean that the
speculative store bypass disable is no longer needed.
A copy of this document is available at:
https://bugzilla.kernel.org/show_bug.cgi?id=199889
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: kvm@vger.kernel.org
Cc: andrew.cooper3@citrix.com
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180601145921.9500-2-konrad.wilk@oracle.com
[bwh: Backported to 3.16:
- The feature bit is in feature word 11
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Hide the AMD_{IBRS,IBPB,STIBP} flag from /proc/cpuinfo. This was done
upstream as part of commit e7c587da12 "x86/speculation: Use
synthetic bits for IBRS/IBPB/STIBP". I already backported that commit
but accidentally dropped this part.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3eb1b955cd upstream.
The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1f74c8a647 upstream.
mce_no_way_out() does a quick check during #MC to see whether some of
the MCEs logged would require the kernel to panic immediately. And it
passes a struct mce where MCi_STATUS gets written.
However, after having saved a valid status value, the next iteration
of the loop which goes over the MCA banks on the CPU, overwrites the
valid status value because we're using struct mce as storage instead of
a temporary variable.
Which leads to MCE records with an empty status value:
mce: [Hardware Error]: CPU 0: Machine Check Exception: 6 Bank 0: 0000000000000000
mce: [Hardware Error]: RIP 10:<ffffffffbd42fbd7> {trigger_mce+0x7/0x10}
In order to prevent the loss of the status register value, return
immediately when severity is a panic one so that we can panic
immediately with the first fatal MCE logged. This is also the intention
of this function and not to noodle over the banks while a fatal MCE is
already logged.
Tony: read the rest of the MCA bank to populate the struct mce fully.
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20180622095428.626-8-bp@alien8.de
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit eab6870fee upstream.
Mark Rutland noticed that GCC optimization passes have the potential to elide
necessary invocations of the array_index_mask_nospec() instruction sequence,
so mark the asm() volatile.
Mark explains:
"The volatile will inhibit *some* cases where the compiler could lift the
array_index_nospec() call out of a branch, e.g. where there are multiple
invocations of array_index_nospec() with the same arguments:
if (idx < foo) {
idx1 = array_idx_nospec(idx, foo)
do_something(idx1);
}
< some other code >
if (idx < foo) {
idx2 = array_idx_nospec(idx, foo);
do_something_else(idx2);
}
... since the compiler can determine that the two invocations yield the same
result, and reuse the first result (likely the same register as idx was in
originally) for the second branch, effectively re-writing the above as:
if (idx < foo) {
idx = array_idx_nospec(idx, foo);
do_something(idx);
}
< some other code >
if (idx < foo) {
do_something_else(idx);
}
... if we don't take the first branch, then speculatively take the second, we
lose the nospec protection.
There's more info on volatile asm in the GCC docs:
https://gcc.gnu.org/onlinedocs/gcc/Extended-Asm.html#Volatile
"
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: babdde2698 ("x86: Implement array_index_mask_nospec")
Link: https://lkml.kernel.org/lkml/152838798950.14521.4893346294059739135.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit be3233fbfc upstream.
Allow the compiler to handle @size as an immediate value or memory
directly rather than allocating a register.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/151797010204.1289.1510000292250184993.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3ae6295ccb upstream.
fpu__drop() has an explicit fwait which under some conditions can trigger a
fixable FPU exception while in kernel. Thus, we should attempt to fixup the
exception first, and only call notify_die() if the fixup failed just like
in do_general_protection(). The original call sequence incorrectly triggers
KDB entry on debug kernels under particular FPU-intensive workloads.
Andy noted, that this makes the whole conditional irq enable thing even
more inconsistent, but fixing that it outside the scope of this.
Signed-off-by: Siarhei Liakh <siarhei.liakh@concurrent-rt.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Borislav Petkov" <bpetkov@suse.de>
Link: https://lkml.kernel.org/r/DM5PR11MB201156F1CAB2592B07C79A03B17D0@DM5PR11MB2011.namprd11.prod.outlook.com
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 18f3e95b90 upstream.
While a barrier is present in the outX() functions before the register
write, a similar barrier is missing in the inX() functions after the
register read. This could allow memory accesses following inX() to
observe stale data.
This patch is very similar to commit a1cc7034e3 ("MIPS: io: Add
barrier after register read in readX()"). Because war_io_reorder_wmb()
is both used by writeX() and outX(), if readX() need a barrier then so
does inX().
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Patchwork: https://patchwork.linux-mips.org/patch/19516/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <james.hogan@mips.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 69a8405999 upstream.
In binutils 2.26 a new opcode for the "wait" instruction was added for the
POWER9 and has precedence over the one specific to the e500mc. Commit
ebf714ff37 ("powerpc/e500mc: Add support for the wait instruction in
e500_idle") uses this instruction specifically on the e500mc to work around
an erratum.
This results in an invalid instruction in idle_e500 when we build for the
e500mc on bintutils >= 2.26 with the default assembler machine type.
Since multiplatform between e500 and non-e500 is not supported, set the
assembler machine type globaly when CONFIG_PPC_E500MC=y.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com>
Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Vakul Garg <vakul.garg@nxp.com>
CC: Scott Wood <swood@redhat.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 91d0697188 upstream.
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a00072a24a upstream.
According to the Intel Software Developers' Manual, Vol. 4, Order No.
335592, these macros have been reversed since they were added in the
initial turbostat commit. The reversed definitions were presumably
copied from turbostat.c to this file.
Fixes: 9c63a650bb ("tools/power/x86/turbostat: share kernel MSR #defines")
Signed-off-by: Matt Turner <mattst88@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3f90f9ef2d upstream.
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d8441ba80c upstream.
ndelay() is supposed to take an unsigned long, but if you define
ndelay() as a macro and the caller pass an unsigned long long instead
of an unsigned long, the unsigned long long to unsigned long cast is
not done and we end up with an "undefined reference to `__udivdi3'"
error at link time.
Fix that by making ndelay() an inline function and then defining dummy
ndelay() macro that redirects to the ndelay() function (it's how most
archs do to implement ndelay()).
Fixes: c8ee038bd1 ("m68k: Implement ndelay() based on the existing udelay() logic")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
[geert: Remove comment now it is no longer a macro]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4f7c06e26e upstream.
In commit e2a800beac ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beac ("powerpc/hw_brk: Fix off by one error when validating DAWR region end")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cd6ef7eebf upstream.
Back when we first introduced the DAWR, in commit 4ae7ebe952
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe952 ("powerpc: Change hardware breakpoint to allow longer ranges")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 76ed0b803a upstream.
NUMREGBYTES (which is used as the size for gdb_regs[]) is incorrectly
based on DBG_MAX_REG_NUM instead of GDB_MAX_REGS. DBG_MAX_REG_NUM
is the number of total registers, while GDB_MAX_REGS is the number
of 'unsigned longs' it takes to serialize those registers. Since
FP registers require 3 'unsigned longs' each, DBG_MAX_REG_NUM is
smaller than GDB_MAX_REGS.
This causes GDB 8.0 give the following error on connect:
"Truncated register 19 in remote 'g' packet"
This also causes the register serialization/deserialization logic
to overflow gdb_regs[], overwriting whatever follows.
Fixes: 834b2964b7 ("kgdb,arm: fix register dump")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rabin Vincent <rabin@rab.in>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cad0e39023 upstream.
The code patching code has always been a bit confused about whether
it's best to use void *, unsigned int *, char *, etc. to point to
instructions. In fact in the feature fixups tests we use both unsigned
int[] and u8[] in different places.
Unfortunately the tests that use unsigned int[] calculate the size of
the code blocks using subtraction of those unsigned int pointers, and
then pass the result to memcmp(). This means we're only comparing 1/4
of the bytes we need to, because we need to multiply by
sizeof(unsigned int) to get the number of *bytes*.
The result is that the tests do all the patching and then only compare
some of the resulting code, so patching bugs that only effect that
last 3/4 of the code could slip through undetected. It turns out that
hasn't been happening, although one test had a bad expected case (see
previous commit).
Fix it for now by multiplying the size by 4 in the affected functions.
Fixes: 362e7701fd ("powerpc: Add self-tests of the feature fixup code")
Epic-brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c69a48cdb3 upstream.
Testing the fortified string functions[1] would cause a kernel panic on
boot in test_feature_fixups() due to a buffer overflow in memcmp.
This boils down to things like this:
extern unsigned int ftr_fixup_test1;
extern unsigned int ftr_fixup_test1_orig;
check(memcmp(&ftr_fixup_test1, &ftr_fixup_test1_orig, size) == 0);
We know that these are asm labels so it is safe to read up to 'size'
bytes at those addresses.
However, because we have passed the address of a single unsigned int to
memcmp, the compiler believes the underlying object is in fact a single
unsigned int. So if size > sizeof(unsigned int), there will be a panic
at runtime.
We can fix this by changing the types: instead of calling the asm labels
unsigned ints, call them unsigned int[]s. Therefore the size isn't
incorrectly determined at compile time and we get a regular unsafe
memcmp and no panic.
[1] http://openwall.com/lists/kernel-hardening/2017/05/09/2
Link: http://lkml.kernel.org/r/1497903987-21002-7-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 32810d9132 upstream.
The expected case for this test was wrong, the source of the alternate
code sequence is:
FTR_SECTION_ELSE
2: or 2,2,2
PPC_LCMPI r3,1
beq 3f
blt 2b
b 3f
b 1b
ALT_FTR_SECTION_END(0, 1)
3: or 1,1,1
or 2,2,2
4: or 3,3,3
So when it's patched the '3' label should still be on the 'or 1,1,1',
and the 4 label is irrelevant and can be removed.
Fixes: 362e7701fd ("powerpc: Add self-tests of the feature fixup code")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 77715b7ddb upstream.
The CPU Measurement sampling facility creates a trailer entry for each
Sample-Data-Block of stored samples. The trailer entry contains the sizes
(in bytes) of the stored sampling types:
- basic-sampling data entry size
- diagnostic-sampling data entry size
Both sizes are 2 bytes long.
This patch changes the trailer entry definition to reflect this.
Fixes: fcc77f5073 ("s390/cpum_sf: Atomically reset trailer entry fields of sample-data-blocks")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3c0a83b14e upstream.
The s390 CPU measurement facility sampling mode supports basic entries
and diagnostic entries. Each entry has a valid bit to indicate the
status of the entry as valid or invalid.
This bit is bit 31 in the diagnostic entry, but the bit mask definition
refers to bit 30.
Fix this by making the reserved field one bit larger.
Fixes: 7e75fc3ff4 ("s390/cpum_sf: Add raw data sampling to support the diagnostic-sampling function")
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 722cde76d6 upstream.
Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.
Fixes: b500afff11 ("fadump: Invalidate registration and release reserved memory for general use.")
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7de712ccc0 upstream.
While working on changing this code to use force_sig_fault I
discovered that do_unaliged_user is sets si_signo to SIGBUS and passes
SIGSEGV to force_sig_info. Which is just b0rked.
The code is reporting a SIGBUS error so replace the SIGSEGV with SIGBUS.
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Fixes: 5a0015d626 ("[PATCH] xtensa: Architecture support for Tensilica Xtensa Part 3")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e48510f451 upstream.
x86_64 allnoconfig:
arch/x86/kernel/cpu/common.c:968: warning: 'syscall32_cpu_init' defined but not used
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 994870bead upstream.
When an inline assembly operand's type is narrower than the register it
is allocated to, the least significant bits of the register (up to the
operand type's width) are valid, and any other bits are permitted to
contain any arbitrary value. This aligns with the AAPCS64 parameter
passing rules.
Our __smp_store_release() implementation does not account for this, and
implicitly assumes that operands have been zero-extended to the width of
the type being stored to. Thus, we may store unknown values to memory
when the value type is narrower than the pointer type (e.g. when storing
a char to a long).
This patch fixes the issue by casting the value operand to the same
width as the pointer operand in all cases, which ensures that the value
is zero-extended as we expect. We use the same union trickery as
__smp_load_acquire and {READ,WRITE}_ONCE() to avoid GCC complaining that
pointers are potentially cast to narrower width integers in unreachable
paths.
A whitespace issue at the top of __smp_store_release() is also
corrected.
No changes are necessary for __smp_load_acquire(). Load instructions
implicitly clear any upper bits of the register, and the compiler will
only consider the least significant bits of the register as valid
regardless.
Fixes: 47933ad41a ("arch: Introduce smp_load_acquire(), smp_store_release()")
Fixes: 878a84d5a8 ("arm64: add missing data types in smp_load_acquire/smp_store_release")
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[bwh: The same upstream commit was already backported to 3.16, but we
didn't have the 1-byte and 2-byte cases then so I dropped that part.
Now that we do, pick up that part again.]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 878a84d5a8 upstream.
Commit 8053871d0f ("smp: Fix smp_call_function_single_async()
locking") introduced a call to smp_load_acquire() with a u16 argument,
but we only cared about u32 and u64 types in that function so far.
This resulted in a compiler warning fortunately, pointing at an
uninitialized use. Due to the implementation structure the compiler
misses that bug in the smp_store_release(), though.
Add the u16 and u8 variants using ldarh/stlrh and ldarb/stlrb,
respectively. Together with the compiletime_assert_atomic_type() check
this should cover all cases now.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c4d2188206 upstream.
The CPUID bits of OSXSAVE (function=0x1) and OSPKE (func=0x7, leaf=0x0)
allows user apps to detect if OS has set CR4.OSXSAVE or CR4.PKE. KVM is
supposed to update these CPUID bits when CR4 is updated. Current KVM
code doesn't handle some special cases when updates come from emulator.
Here is one example:
Step 1: guest boots
Step 2: guest OS enables XSAVE ==> CR4.OSXSAVE=1 and CPUID.OSXSAVE=1
Step 3: guest hot reboot ==> QEMU reset CR4 to 0, but CPUID.OSXAVE==1
Step 4: guest os checks CPUID.OSXAVE, detects 1, then executes xgetbv
Step 4 above will cause an #UD and guest crash because guest OS hasn't
turned on OSXAVE yet. This patch solves the problem by comparing the the
old_cr4 with cr4. If the related bits have been changed,
kvm_update_cpuid() needs to be called.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
[bwh: Backported to 3.16: PKE is not supported]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c7e814628d upstream.
Use 64-bit accesses for 64-bit floating-point general registers with
PTRACE_PEEKUSR, removing the truncation of their upper halves in the
FR=1 mode, caused by commit bbd426f542 ("MIPS: Simplify FP context
access"), which inadvertently switched them to using 32-bit accesses.
The PTRACE_POKEUSR side is fine as it's never been broken and continues
using 64-bit accesses.
Fixes: bbd426f542 ("MIPS: Simplify FP context access")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/19334/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0d73c3f8e7 upstream.
Since do_undefinstr() uses get_user to get the undefined
instruction, it can be called before kprobes processes
recursive check. This can cause an infinit recursive
exception.
Prohibit probing on get_user functions.
Fixes: 24ba613c9d ("ARM kprobes: core code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[bwh: Backported to 3.16: Drop changes to __get_user_{8,32_t_8,64t_{1,2,4}}]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit eb0146daef upstream.
Prohibit kprobes on do_undefinstr because kprobes on
arm is implemented by undefined instruction. This means
if we probe do_undefinstr(), it can cause infinit
recursive exception.
Fixes: 24ba613c9d ("ARM kprobes: core code")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e07e3c33b9 upstream.
In commit 639da5ee37 ("ARM: add an extra temp register to the low
level debugging addruart macro") an additional temporary register was
added to the addruart macro, but the decompressor code wasn't updated.
Fixes: 639da5ee37 ("ARM: add an extra temp register to the low level debugging addruart macro")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit faf37c44a1 upstream.
Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.
We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.16: Drop changes in __{setup,restore}_cpu_power9
and __restore_cpu_cpufeatures()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c1d2a31397 upstream.
Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.
Fixes: 3b8070335f ("powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 19c22f3a29 upstream.
arch/tile added word-at-a-time.h after the patch that added generic-y
entries; the generic-y entry is now stale.
arch/h8300 is newer than the generic-y patch for word-at-a-time.h,
and needs a generic-y entry.
arch/powerpc seems to have gotten a generic-y entry by mistake in
the first patch; this change removes it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
[bwh: Backported to 3.16:
- Drop change in arch/h8300, which doesn't exist here
- Drop change in arch/tile, which is still using the generic implementation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a6e2f029ae upstream.
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
[bwh: Backported to 3.16:
- Drop change in arch/nios2
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit bb7298a7e8 upstream.
VPIF capture driver expects card name to be set since it
uses it without checking for NULL. The commit which
introduced VPIF display and capture support added card
name only for display, not for capture.
Set it in platform data to probe driver successfully.
While at it, also fix the display card name to something more
appropriate.
Fixes: 85609c1ccd ("DaVinci: DM646x - platform changes for vpif capture and display drivers")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9a3a92ccfe upstream.
Check the TIF_32BIT_FPREGS task setting of the tracee rather than the
tracer in determining the layout of floating-point general registers in
the floating-point context, correcting access to odd-numbered registers
for o32 tracees where the setting disagrees between the two processes.
Fixes: 597ce1723e ("MIPS: Support for 64-bit FP with O32 binaries")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
