commit 8a4b06d391 upstream.
Add the sysfs reporting file for MDS. It exposes the vulnerability and
mitigation state similar to the existing files for the other speculative
hardware vulnerabilities.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jon Masters <jcm@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
[bwh: Backported to 3.16:
- Test x86_hyper instead of using hypervisor_is_type()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In this version of the driver, VNIs are consistently kept in host
order. However vxlan_fdb_create() erroneously declares its vni
parameter as __be32, which sparse warns about. Change it to __u32.
This was resolved upstream by commit 54bfd872bf "vxlan: keep flags
and vni in network byte order".
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9f5b8b4f56 upstream.
Remove unused definition which cause the following warnings
drivers/spi/spi-omap-100k.c:73:0: warning: "WRITE" redefined [enabled by default]
include/linux/fs.h:193:0: note: this is the location of the previous definition
drivers/spi/spi-omap-100k.c:74:0: warning: "READ" redefined [enabled by default]
include/linux/fs.h:192:0: note: this is the location of the previous definition
Signed-off-by: Nick Krause <xerofoiffy@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4835f37e3b upstream.
Assure the event data buffer is long enough to hold the array
of netinfo items and that SSID length does not exceed the maximum
of 32 characters as per 802.11 spec.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16:
- Move the assignment to "data" along with the assignment to "netinfo_start"
that depends on it
- Adjust filename, context, indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This reverts commit 9657f3abd1, which
was similar to commit 1b5e242316
upstream. The function fixed upstream doesn't exist in 3.16 and the
similar bug that does exist here needs a different fix.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c7084edc3f upstream.
The n_r3964 line discipline driver was written in a different time, when
SMP machines were rare, and users were trusted to do the right thing.
Since then, the world has moved on but not this code, it has stayed
rooted in the past with its lovely hand-crafted list structures and
loads of "interesting" race conditions all over the place.
After attempting to clean up most of the issues, I just gave up and am
now marking the driver as BROKEN so that hopefully someone who has this
hardware will show up out of the woodwork (I know you are out there!)
and will help with debugging a raft of changes that I had laying around
for the code, but was too afraid to commit as odds are they would break
things.
Many thanks to Jann and Linus for pointing out the initial problems in
this codebase, as well as many reviews of my attempts to fix the issues.
It was a case of whack-a-mole, and as you can see, the mole won.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a4176ec356 upstream.
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16:
- Drop changes to PCIe bus support
- Adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9c349892cc upstream.
Move event handling out of brcmf_netif_rx() avoiding the need
to pass a flag. This flag is only ever true for USB hosts as
other interface use separate brcmf_rx_event() function.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16 as dependency of commit a4176ec356
"brcmfmac: add subtype check for event handling in data path"
- Drop changes to PCIe bus support
- Adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8e290cecdd upstream.
brcmf_sdio_fromevntchan() was being called on the the data frame
rather than the software header, causing some frames to be
mischaracterized as on the event channel rather than the data channel.
This fixes a major performance regression (due to dropped packets). With
this patch the download speed jumped from 1Mbit/s back up to 40MBit/s due
to the sheer amount of packets being incorrectly processed.
Fixes: c56caa9db8 ("brcmfmac: screening firmware event packet")
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[kvalo@codeaurora.org: improve commit logs based on email discussion]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c56caa9db8 upstream.
Firmware uses asynchronized events as a communication method to the
host. The event packets are marked as ETH_P_LINK_CTL protocol type. For
SDIO and PCIe bus, this kind of packets are delivered through virtual
event channel not data channel. This patch adds a screening logic to
make sure the event handler only processes the events coming from the
correct channel.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16:
- Drop changes to PCIe bus support
- Adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 796cfb65e3 upstream.
Avoid spreading the ifidx in the driver, but have it return the
struct brcmf_if instance.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16:
- Drop changes to PCIe bus support
- Adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 75effb03ee upstream.
In rx path the firmware provide an interface index which is used to
map to a struct brcmf_if instance. However, this involves some trick
that is done in two places. This is changed by having driver core
providing brcmf_get_ifp() function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16:
- Drop changes to PCIe bus support
- Adjust filenames]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1b5e242316 upstream.
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 492855939b upstream.
Memory backed DMA mappings are accounted against a user's locked
memory limit, including multiple mappings of the same memory. This
accounting bounds the number of such mappings that a user can create.
However, DMA mappings that are not backed by memory, such as DMA
mappings of device MMIO via mmaps, do not make use of page pinning
and therefore do not count against the user's locked memory limit.
These mappings still consume memory, but the memory is not well
associated to the process for the purpose of oom killing a task.
To add bounding on this use case, we introduce a limit to the total
number of concurrent DMA mappings that a user is allowed to create.
This limit is exposed as a tunable module option where the default
value of 64K is expected to be well in excess of any reasonable use
case (a large virtual machine configuration would typically only make
use of tens of concurrent mappings).
This fixes CVE-2019-3882.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[bwh: Backported to 3.16:
- Add the out_unlock label in vfio_dma_do_map()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6eb5e3399e upstream.
em28xx_dvb_resume() unregisters i2c tuner, i2c demod, and dvb.
This erroneous cleanup results in i2c tuner, i2c demod, and dvb
devices unregistered and removed during resume. This error is a
result of merge conflict between two patches that went into 3.15.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 232ba3a51c upstream.
With Micrel KSZ8061 PHY, the link may occasionally not come up after
Ethernet cable connect. The vendor's (Microchip, former Micrel) errata
sheet 80000688A.pdf descripes the problem and possible workarounds in
detail, see below.
The batch implements workaround 1, which permanently fixes the issue.
DESCRIPTION
Link-up may not occur properly when the Ethernet cable is initially
connected. This issue occurs more commonly when the cable is connected
slowly, but it may occur any time a cable is connected. This issue occurs
in the auto-negotiation circuit, and will not occur if auto-negotiation
is disabled (which requires that the two link partners be set to the
same speed and duplex).
END USER IMPLICATIONS
When this issue occurs, link is not established. Subsequent cable
plug/unplaug cycle will not correct the issue.
WORk AROUND
There are four approaches to work around this issue:
1. This issue can be prevented by setting bit 15 in MMD device address 1,
register 2, prior to connecting the cable or prior to setting the
Restart Auto-negotiation bit in register 0h. The MMD registers are
accessed via the indirect access registers Dh and Eh, or via the Micrel
EthUtil utility as shown here:
. if using the EthUtil utility (usually with a Micrel KSZ8061
Evaluation Board), type the following commands:
> address 1
> mmd 1
> iw 2 b61a
. Alternatively, write the following registers to write to the
indirect MMD register:
Write register Dh, data 0001h
Write register Eh, data 0002h
Write register Dh, data 4001h
Write register Eh, data B61Ah
2. The issue can be avoided by disabling auto-negotiation in the KSZ8061,
either by the strapping option, or by clearing bit 12 in register 0h.
Care must be taken to ensure that the KSZ8061 and the link partner
will link with the same speed and duplex. Note that the KSZ8061
defaults to full-duplex when auto-negotiation is off, but other
devices may default to half-duplex in the event of failed
auto-negotiation.
3. The issue can be avoided by connecting the cable prior to powering-up
or resetting the KSZ8061, and leaving it plugged in thereafter.
4. If the above measures are not taken and the problem occurs, link can
be recovered by setting the Restart Auto-Negotiation bit in
register 0h, or by resetting or power cycling the device. Reset may
be either hardware reset or software reset (register 0h, bit 15).
PLAN
This errata will not be corrected in the future revision.
Fixes: 7ab59dc15e ("drivers/net/phy/micrel_phy: Add support for new PHYs")
Signed-off-by: Alexander Onnasch <alexander.onnasch@landisgyr.com>
Signed-off-by: Rajasingh Thavamani <T.Rajasingh@landisgyr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
- Include <linux/mdio.h> for register definition
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5c27ff5db1 upstream.
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[bwh: Backported to 3.16:
- tmio_mmc_sdio_irq() can be used directly as an interrupt handler, so
make it return IRQ_NONE for unhandled interrupts
- Adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c9bd505dbd upstream.
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
The call tree looks something like this:
mmc_spi_probe
mmc_add_host
mmc_start_host
_mmc_detect_change
mmc_schedule_delayed_work(&host->detect, 0)
mmc_rescan
host->bus_ops->detect(host)
mmc_detect
_mmc_detect_card_removed
host->ops->get_cd(host)
mmc_gpio_get_cd -> -ENOSYS (ctx->cd_gpio not set)
mmc_gpiod_request_cd
ctx->cd_gpio = desc
To fix this issue, call mmc_detect_change after the card-detect GPIO/IRQ
is registered.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8a7493e58a upstream.
We are saving the status of EEE even before we try to enable it. This
leads to a race with XMIT function that tries to arm EEE timer before we
set it up.
Fix this by only saving the EEE parameters after all operations are
performed with success.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: d765955d2a ("stmmac: add the Energy Efficient Ethernet support")
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d358def706 upstream.
In case the hold bit is not needed we are carrying the old values.
Fix the same by resetting the bit when not needed.
Fixes the sporadic i2c bus lockups on National Instruments
Zynq-based devices.
Fixes: df8eb5691c ("i2c: Add driver for Cadence I2C controller")
Reported-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4ae280b4ee upstream.
When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.
When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.
This completion is signaled without first committing the metadata. If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.
Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[bwh: Backported to 3.16:
- bio_endio() takes an error parameter
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2fdeee2549 upstream.
The current opt_inst_list operations inside team_nl_cmd_options_set()
is too complex to track:
LIST_HEAD(opt_inst_list);
nla_for_each_nested(...) {
list_for_each_entry(opt_inst, &team->option_inst_list, list) {
if (__team_option_inst_tmp_find(&opt_inst_list, opt_inst))
continue;
list_add(&opt_inst->tmp_list, &opt_inst_list);
}
}
team_nl_send_event_options_get(team, &opt_inst_list);
as while we retrieve 'opt_inst' from team->option_inst_list, it could
be added to the local 'opt_inst_list' for multiple times. The
__team_option_inst_tmp_find() doesn't work, as the setter
team_mode_option_set() still calls team->ops.exit() which uses
->tmp_list too in __team_options_change_check().
Simplify the list operations by moving the 'opt_inst_list' and
team_nl_send_event_options_get() into the nla_for_each_nested() loop so
that it can be guranteed that we won't insert a same list entry for
multiple times. Therefore, __team_option_inst_tmp_find() can be removed
too.
Fixes: 4fb0534fb7 ("team: avoid adding twice the same option to the event list")
Fixes: 2fcdb2c9e6 ("team: allow to send multiple set events in one message")
Reported-by: syzbot+4d4af685432dc0e56c91@syzkaller.appspotmail.com
Reported-by: syzbot+68ee510075cf64260cc4@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4179cb5a4c upstream.
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f9 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Fixes: ce6502a8f9 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e8b22d0a32 upstream.
Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech
touchpad, but the driver needs to be told so to enable the middle touchpad
button.
The elantech_dmi_force_crc_enabled quirk was not necessary with the H780.
Also document the fw_version and caps values detected for both H760 and
H780 models.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f9a703a54d upstream.
Just like Fujitsu CELSIUS H730, the H760 also has an Elantech touchpad with
the same quirks. Without this patch, the touchpad is useless out-of-the-box
as the mouse pointer won't move.
This patch makes the driver aware of both the crc_enabled=1 requirement and
the middle button, making the touchpad fully functional out-of-the-box.
Signed-off-by: Matti Kurkela <Matti.Kurkela@iki.fi>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit dd957493ba upstream.
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d5d27fd982 upstream.
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
Fixes: 6f2a6a5256 ("mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems")
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4cbfa1e6c0 upstream.
Previously we set only the dma mask and not the coherent mask. Fix that.
Also, for clarity, make sure both are initially set to 64 bits.
Fixes: 0d00c488f3: ("drm/vmwgfx: Fix the driver for large dma addresses")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 728354c005 upstream.
The function was unconditionally returning 0, and a caller would have to
rely on the returned fence pointer being NULL to detect errors. However,
the function vmw_execbuf_copy_fence_user() would expect a non-zero error
code in that case and would BUG otherwise.
So make sure we return a proper non-zero error code if the fence pointer
returned is NULL.
Fixes: ae2a104058: ("vmwgfx: Implement fence objects")
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c0a2e4d10d upstream.
Work for Bridgeport events is currently placed on a driver-wide
workqueue. If the card is removed and freed while any such work is still
active, this causes a use-after-free.
So put the events on a per-card queue, where we can control their
lifetime. As we also don't want stale events to last beyond an
offline & online cycle, flush this queue when setting the card offline.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
- Add gdev parameter to qeth_alloc_card(), as done upstream by commit
121ca39aa5 "s390/qeth: uninstall IRQ handler on device removal"
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c2780c1a3f upstream.
A card's close_dev work is scheduled on a driver-wide workqueue. If the
card is removed and freed while the work is still active, this causes a
use-after-free.
So make sure that the work is completed before freeing the card.
Fixes: 0f54761d16 ("qeth: Support VEPA mode")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit afa0c5904b upstream.
The error path in qeth_alloc_qdio_buffers() that takes care of
cleaning up the Output Queues is buggy. It first frees the queue, but
then calls qeth_clear_outq_buffers() with that very queue struct.
Make the call to qeth_clear_outq_buffers() part of the free action
(in the correct order), and while at it fix the naming of the helper.
Fixes: 0da9581ddb ("qeth: exploit asynchronous delivery of storage blocks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
- Add the qeth_free_output_queue() function, which didn't exist here
- Keep using kfree() to free to free the qeth_qdio_out_q structure]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0255200bd2 upstream.
After the DMA transfer is done, we don't need to call the un-mapping code
in 3 places. One is enough.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bwh: Backported to 3.16 as dependency of commit 6454368a80
"dmaengine: dmatest: Abort test in case of mapping error"]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9e528c799d upstream.
There are multiple issues with bcm2835_dma_abort() (which is called on
termination of a transaction):
* The algorithm to abort the transaction first pauses the channel by
clearing the ACTIVE flag in the CS register, then waits for the PAUSED
flag to clear. Page 49 of the spec documents the latter as follows:
"Indicates if the DMA is currently paused and not transferring data.
This will occur if the active bit has been cleared [...]"
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
So the function is entering an infinite loop because it is waiting for
PAUSED to clear which is always set due to the function having cleared
the ACTIVE flag. The only thing that's saving it from itself is the
upper bound of 10000 loop iterations.
The code comment says that the intention is to "wait for any current
AXI transfer to complete", so the author probably wanted to check the
WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function
accordingly.
* The CS register is only read at the beginning of the function. It
needs to be read again after pausing the channel and before checking
for outstanding writes, otherwise writes which were issued between
the register read at the beginning of the function and pausing the
channel may not be waited for.
* The function seeks to abort the transfer by writing 0 to the NEXTCONBK
register and setting the ABORT and ACTIVE flags. Thereby, the 0 in
NEXTCONBK is sought to be loaded into the CONBLK_AD register. However
experimentation has shown this approach to not work: The CONBLK_AD
register remains the same as before and the CS register contains
0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control
block is not aborted but merely paused and it will be resumed once the
next DMA transaction is started. That is absolutely not the desired
behavior.
A simpler approach is to set the channel's RESET flag instead. This
reliably zeroes the NEXTCONBK as well as the CS register. It requires
less code and only a single MMIO write. This is also what popular
user space DMA drivers do, e.g.:
https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c
Note that the spec is contradictory whether the NEXTCONBK register
is writeable at all. On the one hand, page 41 claims:
"The value loaded into the NEXTCONBK register can be overwritten so
that the linked list of Control Block data structures can be
dynamically altered. However it is only safe to do this when the DMA
is paused."
On the other hand, page 40 specifies:
"Only three registers in each channel's register set are directly
writeable (CS, CONBLK_AD and DEBUG). The other registers (TI,
SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically
loaded from a Control Block data structure held in external memory."
Fixes: 96286b5766 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit f7da7782ab upstream.
If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Fixes: 96286b5766 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit e42685d7a7 upstream.
Add additional defines describing the DMA registers
as well as adding some more documentation to those registers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
[bwh: Backported to 3.16 as dependency of commit 9e528c799d
"dmaengine: bcm2835: Fix abort of transactions"]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 341198eda7 upstream.
Once the "ld_queue" list is not empty, next descriptor will migrate
into "ld_active" list. The "desc" variable will be overwritten
during that transition. And later the dmaengine_desc_get_callback_invoke()
will use it as an argument. As result we invoke wrong callback.
That behaviour was in place since:
commit fcaaba6c71 ("dmaengine: imx-dma: fix callback path in tasklet").
But after commit 4cd13c21b2 ("softirq: Let ksoftirqd do its job")
things got worse, since possible delay between tasklet_schedule()
from DMA irq handler and actual tasklet function execution got bigger.
And that gave more time for new DMA request to be submitted and
to be put into "ld_queue" list.
It has been noticed that DMA issue is causing problems for "mxc-mmc"
driver. While stressing the system with heavy network traffic and
writing/reading to/from sd card simultaneously the timeout may happen:
10013000.sdhci: mxcmci_watchdog: read time out (status = 0x30004900)
That often lead to file system corruption.
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 294c149a20 upstream.
The "p" buffer is 0x4000 bytes long. B3_RI_WTO_R1 is 0x190. The value
of "regs->len" is in the 1-0x4000 range. The bug here is that
"regs->len - B3_RI_WTO_R1" can be a negative value which would lead to
memory corruption and an abrupt crash.
Fixes: c3f8be9618 ("[PATCH] skge: expand ethtool debug register dump")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c418fd6c01 upstream.
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] b0be3b6cc1:beagleboard-usbsniffer-kernel.git;a=patch;h=b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Fold in the earlier commit fb91cddc54 "usb: musb: Remove DMA ifdef
for musb_gadget.c short_packet"
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b2d3492fc5 upstream.
There are two issues here. First if cmgr->hba is not set early enough then
it leads to a NULL dereference. Second if we don't completely initialize
cmgr->io_bdt_pool[] then we end up dereferencing uninitialized pointers.
Fixes: 853e2bd210 ("[SCSI] bnx2fc: Broadcom FCoE offload driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backorted to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4a8ef6999b upstream.
Dan Carpenter reported the following:
The patch 52898025cf: "[S390] dasd: security and PSF update patch
for EMC CKD ioctl" from Mar 8, 2010, leads to the following static
checker warning:
drivers/s390/block/dasd_eckd.c:4486 dasd_symm_io()
error: using offset into zero size array 'psf_data[]'
drivers/s390/block/dasd_eckd.c
4458 /* Copy parms from caller */
4459 rc = -EFAULT;
4460 if (copy_from_user(&usrparm, argp, sizeof(usrparm)))
^^^^^^^
The user can specify any "usrparm.psf_data_len". They choose zero by
mistake.
4461 goto out;
4462 if (is_compat_task()) {
4463 /* Make sure pointers are sane even on 31 bit. */
4464 rc = -EINVAL;
4465 if ((usrparm.psf_data >> 32) != 0)
4466 goto out;
4467 if ((usrparm.rssd_result >> 32) != 0)
4468 goto out;
4469 usrparm.psf_data &= 0x7fffffffULL;
4470 usrparm.rssd_result &= 0x7fffffffULL;
4471 }
4472 /* alloc I/O data area */
4473 psf_data = kzalloc(usrparm.psf_data_len, GFP_KERNEL
| GFP_DMA);
4474 rssd_result = kzalloc(usrparm.rssd_result_len, GFP_KERNEL
| GFP_DMA);
4475 if (!psf_data || !rssd_result) {
kzalloc() returns a ZERO_SIZE_PTR (0x16).
4476 rc = -ENOMEM;
4477 goto out_free;
4478 }
4479
4480 /* get syscall header from user space */
4481 rc = -EFAULT;
4482 if (copy_from_user(psf_data,
4483 (void __user *)(unsigned long)
usrparm.psf_data,
4484 usrparm.psf_data_len))
That all works great.
4485 goto out_free;
4486 psf0 = psf_data[0];
4487 psf1 = psf_data[1];
But now we're assuming that "->psf_data_len" was at least 2 bytes.
Fix this by checking the user specified length psf_data_len.
Fixes: 52898025cf ("[S390] dasd: security and PSF update patch for EMC CKD ioctl")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a53469a68e upstream.
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d763 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup")
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 07c69f1148 upstream.
(!x & y) strikes again.
Fix bitwise and boolean operations by enclosing the expression:
intcsr & (1 << NET2272_PCI_IRQ)
in parentheses, before applying the boolean operator '!'.
Notice that this code has been there since 2011. So, it would
be helpful if someone can double-check this.
This issue was detected with the help of Coccinelle.
Fixes: ceb80363b2 ("USB: net2272: driver for PLX NET2272 USB device controller")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6ab4aba00f upstream.
The following BUG was reported by kasan:
BUG: KASAN: use-after-free in ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
Read of size 80 at addr ffff88034c30bcd0 by task kworker/u16:1/24020
Workqueue: ipoib_wq ipoib_cm_tx_start [ib_ipoib]
Call Trace:
dump_stack+0x9a/0xeb
print_address_description+0xe3/0x2e0
kasan_report+0x18a/0x2e0
? ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
memcpy+0x1f/0x50
ipoib_cm_tx_start+0x430/0x1390 [ib_ipoib]
? kvm_clock_read+0x1f/0x30
? ipoib_cm_skb_reap+0x610/0x610 [ib_ipoib]
? __lock_is_held+0xc2/0x170
? process_one_work+0x880/0x1960
? process_one_work+0x912/0x1960
process_one_work+0x912/0x1960
? wq_pool_ids_show+0x310/0x310
? lock_acquire+0x145/0x440
worker_thread+0x87/0xbb0
? process_one_work+0x1960/0x1960
kthread+0x314/0x3d0
? kthread_create_worker_on_cpu+0xc0/0xc0
ret_from_fork+0x3a/0x50
Allocated by task 0:
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc_trace+0x168/0x3e0
path_rec_create+0xa2/0x1f0 [ib_ipoib]
ipoib_start_xmit+0xa98/0x19e0 [ib_ipoib]
dev_hard_start_xmit+0x159/0x8d0
sch_direct_xmit+0x226/0xb40
__dev_queue_xmit+0x1d63/0x2950
neigh_update+0x889/0x1770
arp_process+0xc47/0x21f0
arp_rcv+0x462/0x760
__netif_receive_skb_core+0x1546/0x2da0
netif_receive_skb_internal+0xf2/0x590
napi_gro_receive+0x28e/0x390
ipoib_ib_handle_rx_wc_rss+0x873/0x1b60 [ib_ipoib]
ipoib_rx_poll_rss+0x17d/0x320 [ib_ipoib]
net_rx_action+0x427/0xe30
__do_softirq+0x28e/0xc42
Freed by task 26680:
__kasan_slab_free+0x11d/0x160
kfree+0xf5/0x360
ipoib_flush_paths+0x532/0x9d0 [ib_ipoib]
ipoib_set_mode_rss+0x1ad/0x560 [ib_ipoib]
set_mode+0xc8/0x150 [ib_ipoib]
kernfs_fop_write+0x279/0x440
__vfs_write+0xd8/0x5c0
vfs_write+0x15e/0x470
ksys_write+0xb8/0x180
do_syscall_64+0x9b/0x420
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff88034c30bcc8
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 8 bytes inside of
512-byte region [ffff88034c30bcc8, ffff88034c30bec8)
The buggy address belongs to the page:
The following race between change mode and xmit flow is the reason for
this use-after-free:
Change mode Send packet 1 to GID XX Send packet 2 to GID XX
| | |
start | |
| | |
| | |
| Create new path for GID XX |
| and update neigh path |
| | |
| | |
| | |
flush_paths | |
| |
queue_work(cm.start_task) |
| Path for GID XX not found
| create new path
|
|
start_task runs with old
released path
There is no locking to protect the lifetime of the path through the
ipoib_cm_tx struct, so delete it entirely and always use the newly looked
up path under the priv->lock.
Fixes: 546481c281 ("IB/ipoib: Fix memory corruption in ipoib cm mode connect flow")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a40ded6043 upstream.
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654b ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16:
- There are no num_sys_eqs or dmfs_high_steer_mode parameters
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
