commit a882b14fe8 upstream.
Commit b5ada4600d ("drivers/rtc/rtc-cmos.c: fix compilation warning
when !CONFIG_PM_SLEEP") broke wakeup from S5 by making cmos_poweroff a
nop unless CONFIG_PM_SLEEP was defined.
Fix this by restricting the #ifdef to cmos_resume and restoring the old
dependency on CONFIG_PM for cmos_suspend and cmos_poweroff.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85560c4a82 upstream.
Suspend could fail for some platforms because
btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs.
When btusb_bulk_complete returns before system suspend and resubmits
an URB, the system cannot enter suspend state.
Signed-off-by: Champion Chen <champion_chen@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4807b51895 upstream.
In this expression: seq = (seq - 1) % 8
seq (u8) is implicitly converted to an int in the arithmetic operation.
So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1.
The new seq value is 0xff which is an invalid ACK value, we expect 0x07.
It leads to frequent dropped ACK and retransmission.
Fix this by using '&' binary operator instead of '%'.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 171cdab8c7 upstream.
This reverts commit 09efc56345
I've received reports that this change is decreasing throughput in some
rare conditions on an AR9280 based device
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01f7feeaf4 upstream.
Two bits control TX power on BBP_R1 register. Correct the mask,
otherwise we clear additional bit on BBP_R1 register, what can have
unknown, possible negative effect.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89ec3dcf17 upstream.
Some implementations of modprobe fail to load the driver for a PCI device
automatically because the "interface" part of the modalias from the kernel
is lowercase, and the modalias from file2alias is uppercase.
The "interface" is the low-order byte of the Class Code, defined in PCI
r3.0, Appendix D. Most interface types defined in the spec do not use
alpha characters, so they won't be affected. For example, 00h, 01h, 10h,
20h, etc. are unaffected.
Print the "interface" byte of the Class Code in uppercase hex, as we
already do for the Vendor ID, Device ID, Class, etc.
[bhelgaas: changelog]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fe373f999 upstream.
The Crocodile chip occasionally comes up with 4k and 8k BAR sizes. Due to
an erratum, setting the SR-IOV page size causes the physical function BARs
to expand to the system page size. Since ppc64 uses 64k pages, when Linux
tries to assign the smaller resource sizes to the now 64k BARs the address
will be truncated and the BARs will overlap.
Force Linux to allocate the resource as a full page, which avoids the
overlap.
[bhelgaas: print expanded resource, too]
Signed-off-by: Douglas Lehr <dllehr@us.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d61b0e87d2 upstream.
In 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to
64-bit resources"), we added IORESOURCE_MEM_64 to the mask in
pci_assign_unassigned_root_bus_resources(), but not to the mask in
pci_assign_unassigned_bridge_resources().
Add IORESOURCE_MEM_64 to the pci_assign_unassigned_bridge_resources() type
mask.
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56fab6e189 upstream.
Geert Uytterhoeven reported a warning when building pci-mvebu:
drivers/pci/host/pci-mvebu.c: In function 'mvebu_get_tgt_attr':
drivers/pci/host/pci-mvebu.c:887:39: warning: 'rtype' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (slot == PCI_SLOT(devfn) && type == rtype) {
^
And indeed, the code of mvebu_get_tgt_attr() may lead to the usage of rtype
when being uninitialized, even though it would only happen if we had
entries other than I/O space and 32 bits memory space.
This commit fixes that by simply skipping the current DT range being
considered, if it doesn't match the resource type we're looking for.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e45ef682c upstream.
Do full clean up at exit, means terminate all ongoing DMA transfers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc3187564e upstream.
If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cfda2794b5 upstream.
function 'strncpy' will fill whole buffer 'id.name' of fixed size (32)
with string value and will not leave place for NULL-terminator.
Possible buffer boundaries violation in following string operations.
Replace strncpy with strlcpy.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b29ef3546a upstream.
Minimize failures in this function by pre-allocating the buffer
for posting messages. The hypercall for posting the message can fail
for a number of reasons:
1. Transient resource related issues
2. Buffer alignment
3. Buffer cannot span a page boundry
We address issues 2 and 3 by preallocating a per-cpu page for the buffer.
Transient resource related failures are handled by retrying by the callers
of this function.
This patch is based on the investigation
done by Dexuan Cui <decui@microsoft.com>.
I would like to thank Sitsofe Wheeler <sitsofe@yahoo.com>
for reporting the issue and helping in debuggging.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45d727cee9 upstream.
Fix a bug in vmbus_open() and properly propagate the error. I would
like to thank Dexuan Cui <decui@microsoft.com> for identifying the
issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72c6b71c24 upstream.
Eliminate the call to BUG_ON() by waiting for the host to respond. We are
trying to reclaim the ownership of memory that was given to the host and so
we will have to wait until the host responds.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 98d731bb06 upstream.
Eliminate calls to BUG_ON() in vmbus_close_internal().
We have chosen to potentially leak memory, than crash the guest
in case of failures.
In this version of the patch I have addressed comments from
Dan Carpenter (dan.carpenter@oracle.com).
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66be653083 upstream.
Eliminate calls to BUG_ON() by properly handling errors. In cases where
rollback is possible, we will return the appropriate error to have the
calling code decide how to rollback state. In the case where we are
transferring ownership of the guest physical pages to the host,
we will wait for the host to respond.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdeebcc622 upstream.
Posting messages to the host can fail because of transient resource
related failures. Correctly deal with these failures and increase the
number of attempts to post the message before giving up.
In this version of the patch, I have normalized the error code to
Linux error code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 471b095dfe upstream.
An empty firmware request name will trigger warnings when building
device names. Make sure this is caught earlier and rejected.
The warning was visible via the test_firmware.ko module interface:
echo -ne "\x00" > /sys/devices/virtual/misc/test_firmware/trigger_request
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db7157d4cf upstream.
Once calling scsi_host_put, be careful to not access qla_hw_data through
the Scsi_Host private data (ie, scsi_qla_host base_vha).
Fixes: fe1b806f4f ("qla2xxx: Refactor shutdown code so some functionality can be reused")
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78c2106a50 upstream.
This patch is to fix regression added by commit id
51a07f8464.
When allocating memory for new session original patch does
not assign vha to op->vha resulting into NULL pointer
access during qlt_create_sess_from_atio().
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5bb725ac2 upstream.
VCCR is used as a trigger to start voltage transitions, so
we need to mark it volatile in order to make sure it gets
written to hardware every time we set a new voltage.
Fixes regulator voltage being stuck at the first voltage
set after driver load.
[lst: reworded commit message]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4089b71cc8 upstream.
When using a virtual SCSI disk in a VMWare VM if blkdev_issue_zeroout is used
data can be improperly zeroed out using the mptfusion driver. This patch
disables write_same for this driver and the vmware subsystem_vendor which
ensures that manual zeroing out is used instead.
BugLink: http://bugs.launchpad.net/bugs/1371591
Reported-by: Bruce Lucas <bruce.lucas@mongodb.com>
Tested-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a41a9ad3bb upstream.
Dan Carpenter found a issue where be2iscsi would copy the ip
from userspace to the driver buffer before checking the len
of the data being copied:
http://marc.info/?l=linux-scsi&m=140982651504251&w=2
This patch just has us only copy what we the driver buffer
can support.
Tested-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6b41cb060 upstream.
Since we cannot make sure the 'val_count' will always be none zero
here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmemdup().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5336be8416 upstream.
If LOG_DEVICE is defined and map->dev is NULL it will lead to NULL
pointer dereference. This patch fixes this issue by adding check for
dev->NULL in all such places in regmap.c
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c98e0c1cc upstream.
If 'map->dev' is NULL and there will lead dev_name() to be NULL pointer
dereference. So before dev_name(), we need to have check of the map->dev
pionter.
We also should make sure that the 'name' pointer shouldn't be NULL for
debugfs_create_dir(). So here using one default "dummy" debugfs name when
the 'name' pointer and 'map->dev' are both NULL.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b65c2a029 upstream.
In the Dell XPS 13 9333, it appears that sometimes the bus get confused
and corrupts the incoming data. It fills the input report with the
sentinel value "ff". Synaptics told us that such behavior does not comes
from the touchpad itself, so we filter out such reports here.
Unfortunately, we can not simply discard the incoming data because they
may contain useful information. Most of the time, the misbehavior is
quite near the end of the report, so we can still use the valid part of
it.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1123584
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb57862ead upstream.
If the driver was compiled with DMA support, but DMA channels weren't acquired
by some reason, mid_spi_dma_exit() will crash the kernel.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b41583e729 upstream.
In case of 8 bit mode and DMA usage we end up with every second byte written as
0. We have to respect bits_per_word settings what this patch actually does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ede7dcca3 upstream.
Quark X1000 contains two designware derived 8250 serial ports.
Each port has a unique PCI configuration space consisting of
BAR0:UART BAR1:DMA respectively.
Unlike the standard 8250 the register width is 32 bits for RHR,IER etc
The Quark UART has a fundamental clock @ 44.2368 MHz allowing for a
bitrate of up to about 2.76 megabits per second.
This patch enables standard 8250 mode
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33ead538f6 upstream.
Commit 92d585ef06 ("numa: fix NULL pointer access and memory
leak in unregister_one_node()") added kfree() of node struct in
unregister_one_node(). But node struct is freed by node_device_release()
which is called in unregister_node(). So by adding the kfree(),
node struct is freed two times.
While hot removing memory, the commit leads the following BUG_ON():
kernel BUG at mm/slub.c:3346!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
[...] unregister_one_node
[...] try_offline_node
[...] remove_memory
[...] acpi_memory_device_remove
[...] acpi_bus_trim
[...] acpi_bus_trim
[...] acpi_device_hotplug
[...] acpi_hotplug_work_fn
[...] process_one_work
[...] worker_thread
[...] ? rescuer_thread
[...] kthread
[...] ? kthread_create_on_node
[...] ret_from_fork
[...] ? kthread_create_on_node
This patch removes unnecessary kfree() from unregister_one_node().
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Fixes: 92d585ef06 "numa: fix NULL pointer access and memory leak in unregister_one_node()"
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4451d494b1 upstream.
buf_0 and buf_1 in caam_hash_state are not next to each other.
Accessing buf_1 is incorrect from &buf_0 with an offset of only
size_of(buf_0). The same issue is also with buflen_0 and buflen_1
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 468bcc2a2c upstream.
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dee80ad12d upstream.
Added the Seluxit ApS USB Serial Dongle to cp210x driver.
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bfc2d7dfdd upstream.
Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.
Signed-off-by: Joe Savage <joe.savage@goketra.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddbe1fca0b upstream.
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 710f1bf16a upstream.
As most ASM1051 based devices, this one has unfixable issues with uas too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 734016b00b upstream.
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 593078525c upstream.
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3a67c9ccad ]
After the packet is successfully sent, we should not touch the packet
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47549650ab ]
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
THREAD 1 THREAD 2
======== ========
team_notify_peers(teamX)
atomic_set count_pending = 1
schedule_delayed_work
team_notify_peers(teamX)
atomic_set count_pending = 1
team_notify_peers_work
atomic_dec_and_test
count_pending = 0
(return)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test
count_pending = -1
schedule_delayed_work
(repeat until count_pending = 0)
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e87474a6e6 ]
Similar to commit bc23333ba1 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dedb845ded ]
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
