commit 0e6e448bdc upstream.
There are two pin groups for the FSIC SPDIF signal, but the FSIC pin
group array lists only one, and it refers to a nonexistent group.
Fixes: 2ecd4154c9 ("sh-pfc: sh73a0: Add FSI pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a4b0350047 upstream.
The entry for "scifb2_data_c" in the SCIFB2 pin group array contains a
typo, thus the group cannot be selected.
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8e32e88194 upstream.
When declaring the HSPI RX1_B and TX1_B pins, two mistakes were made:
- the rows and columns in the BGA pin matrix, from which the pin
numbers are derived, were exchanged,
- it was not taken into account that pin row labelling skips
characters I, O, Q, and S.
Fix the order, and the corresponding pin names.
Notes:
- The actual values of the pin numbers don't really matter (they just
have to be unique), so the wrong order didn't have any impact,
- Changing the names of the pins is user-visible, but there are no
users in (upstream) DTS files.
Fixes: 4f82e3ee72 ("sh-pfc: Support pins not associated with a GPIO port")
Fixes: 09cc76a958 ("sh-pfc: r8a7778: add HSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 054f2400f7 upstream.
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4d374bacd7 upstream.
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9540cbdfcd upstream.
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1b99d0c80b upstream.
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc421 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 94482af705 upstream.
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 124cde98f8 upstream.
The tpu4_to3_mux[] array contains the TPU4TO3 pin mark, but the
tpu4_to3_pins[] array lacks the corresponding pin number.
Add the missing pin number, for non-GPIO pin F26.
Fixes: 5da4eb049d ("sh-pfc: sh73a0: Add TPU pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0d6256cb88 upstream.
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 884fa25fb6 upstream.
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 96bb2a6ab4 upstream.
The lcd0_data24_1_pins[] array contains the LCD0 D1[2-5] pin numbers,
but the lcd0_data24_1_mux[] array lacks the corresponding pin marks.
Fixes: 06c7dd866d ("sh-pfc: r8a7740: Add LCDC0 and LCDC1 pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1ebc589a77 upstream.
The gether_gmii_mux[] array contains the REF125CK pin mark, but the
gether_gmii_pins[] array lacks the corresponding pin number.
Fixes: bae11d30d0 ("sh-pfc: r8a7740: Add GETHER pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b5031b7db7 upstream.
fixes following Smatch static check warning:
drivers/pinctrl/berlin/berlin.c:237 berlin_pinctrl_build_state()
warn: passing devm_ allocated variable to kfree. 'pctrl->functions'
As we will be calling krealloc() on pointer 'pctrl->functions', which means
kfree() will be called in there, devm_kzalloc() shouldn't be used with
the allocation in the first place. Fix the warning by calling kcalloc()
and managing the free procedure in error path on our own.
Fixes: 3de68d331c ("pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: berlin_pinctrl_state() was not yet converted
to devm_kcalloc()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 19da44cd33 upstream.
The info->groups[] array is allocated in imx1_pinctrl_parse_dt(). It
has info->ngroups elements. Thus the > here should be >= to prevent
reading one element beyond the end of the array.
Fixes: 30612cd900 ("pinctrl: imx1 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Uwe Kleine-König <u.kleine-könig@pengutronix.de>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b4859f3edb upstream.
The > should really be >= here. It's harmless because
pinctrl_generic_get_group() will return a NULL if group is invalid.
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 05e0c82895 upstream.
If you do this on an sdm845 board:
cat /sys/kernel/debug/pinctrl/3400000.pinctrl/pinconf-groups
...it looks like nonsense. For every pin you see listed:
input bias bus hold, input bias disabled, input bias pull down, input bias pull up
That's because msm_config_group_get() isn't complying with the rules
that pinconf_generic_dump_one() expects. Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.
Let's fix this.
From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist. I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases. While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.
Fixes: f365be0925 ("pinctrl: Add Qualcomm TLMM driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16:
- Drop change to case PIN_CONFIG_BIAS_BUS_HOLD
- Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5cf9a338db upstream.
All banks with GPIO interrupts should be at beginning of bank array and
without any other types of banks between them. This order is expected
by exynos_eint_gpio_irq, when doing interrupt group to bank translation.
Otherwise, kernel NULL pointer dereference would happen when trying to
handle interrupt, due to wrong bank being looked up. Observed on
s5pv210, when trying to handle gpj0 interrupt, where kernel was mapping
it to gpi bank.
Fixes: 023e06dfa6 ("pinctrl: exynos: add exynos5410 SoC specific data")
Fixes: 608a26a7bc ("pinctrl: Add s5pv210 support to pinctrl-exynos)
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[bwh: Backported to 3.16:
- Drop change to exynos5410_pin_banks0
- Adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 45dcb54f01 upstream.
This fixes pcs_request_gpio() in the pinctrl-single driver when
bits_per_mux != 0. It appears this was overlooked when the multiple
pins per register feature was added.
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 981ed1bfbc upstream.
In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.
In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().
[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.
Fixes: 6e5e959dde ("pinctrl: API changes to support multiple states per device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d81ece747d upstream.
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 66b54e3a5a upstream.
The original implemented debug message does not work for
SHARE_MUX_CONF_REG case. This patch fixes it.
Fixes: bf5a530971 ("pinctrl: imx: add VF610 support to imx pinctrl framework")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit da6c2addf6 upstream.
To set the mux mode of a pin two bits must be set. Up to now this is
implemented using the following idiom:
writel(mask, reg + CLR);
writel(value, reg + SET);
. This however results in the mux mode being 0 between the two writes.
On my machine there is an IC's reset pin connected to LCD_D20. The
bootloader configures this pin as GPIO output-high (i.e. not holding the
IC in reset). When Linux reconfigures the pin to GPIO the short time
LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse
the connected IC.
The same problem is present for the pin's drive strength setting which is
reset to low drive strength before using the right value.
So instead of relying on the hardware to modify the register setting
using two writes implement the bit toggling using read-modify-write.
Fixes: 17723111e6 ("pinctrl: add pinctrl-mxs support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bwh: Backported to 3.16: adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0cbdc11482 upstream.
The IPSR field names in the comments have been fat-fingered in a couple
places -- fix those silly typos...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 58439280f8 upstream.
PINMUX_IPSR_MSEL() macro invocation for the TX2 signal has apparently wrong
1st argument -- most probably a result of cut&paste programming...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[bwh: Backported to 3.16:
- Use PINMUX_IPSR_MODSEL_DATA() instead of PINMUX_IPSR_MSEL()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3908632fb8 upstream.
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the DVC_MUTE signal altogether in
the PFC section. The modern manual has the signal described, so just add
the necassary data to the driver...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[bwh: Backported to 3.16:
- Use PINMUX_IPSR_DATA() instead of PINMUX_IPSR_GPSR()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit da7a692fbb upstream.
The R8A7791 PFC driver was apparently based on the preliminary revisions
of the user's manual, which omitted the HSCIF1 group E signals in the
IPSR4 register description. This would cause HSCIF1's probe to fail with
the messages like below:
sh-pfc e6060000.pfc: cannot locate data/mark enum_id for mark 1989
sh-sci e62c8000.serial: Error applying setting, reverse things back
sh-sci: probe of e62c8000.serial failed with error -22
Add the neceassary PINMUX_IPSR_MSEL() invocations for the HSCK1_E,
HCTS1#_E, and HRTS1#_E signals...
Fixes: 5088451962 ("pinctrl: sh-pfc: r8a7791 PFC support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[bwh: Backported to 3.16:
- Use PINMUX_IPSR_MODSEL_DATA() instead of PINMUX_IPSR_MSEL()
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3091ae775f upstream.
Update the sh_pfc_soc_info pointer after calling the SoC-specific
initialization function, as it may have been updated to e.g. handle
different SoC revisions. This makes sure the correct subdriver name is
printed later.
Fixes: 0c151062f3 ("sh-pfc: Add support for SoC-specific initialization")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 0ac3c0a402 upstream.
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 56b367c0cd upstream.
pcs_parse_bits_in_pinctrl_entry uses ffs which gives bit indices
ranging from 1 to MAX. This leads to a corner case where we try to request
the pin number = MAX and fails.
bit_pos value is being calculted using ffs. pin_num_from_lsb uses
bit_pos value. pins array is populated with:
pin + pin_num_from_lsb.
The above is 1 more than usual bit indices as bit_pos uses ffs to compute
first set bit. Hence the last of the pins array is populated with the MAX
value and not MAX - 1 which causes error when we call pin_request.
mask_pos is rightly calculated as ((pcs->fmask) << (bit_pos - 1))
Consequently val_pos and submask are correct.
Hence use __ffs which gives (ffs(x) - 1) as the first bit set.
fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 53653c6b91 upstream.
In case of an invalid pin value bcm2835_pctl_dt_node_to_map()
would leak the pull configs of already assigned pins.
So avoid this by calling the free map function in error case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e1b2dc70cd ("pinctrl: add bcm2835 driver")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/pinctrl/bcm/pinctrl-bcm2835.c ->
drivers/pinctrl/pinctrl-bcm2835.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4c02cba18c upstream.
Currently the provided initial value for bcm2835_gpio_direction_output
has no effect. So fix this issue by changing the value before
changing the GPIO direction. As a result we need to move the function below
bcm2835_gpio_set.
Suggested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Fixes: e1b2dc70cd ("pinctrl: add bcm2835 driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/pinctrl/bcm/pinctrl-bcm2835.c ->
drivers/pinctrl/pinctrl-bcm2835.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 27e7cd0165 upstream.
The pinctrl_gpio_range[] array described a first bank of 32 GPIOs and
a second one of 27 GPIOs. However, since there is a total of 60 MPP
pins that can be muxed as GPIOs, the second bank really has 28 GPIOs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d538990ee1 upstream.
There was an incorrect space in the definition of the function of one
pin in the Armada 375 pinctrl driver, which this commit fixes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: ce3ed59dcd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit ea78b9511a upstream.
There was a mistake in the definition of the functions for MPP48 on
Marvell Armada XP. The second function is dev(clkout), and not tclk.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 80b3d04fea upstream.
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit bc99357f36 upstream.
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 463e270f76 ("pinctrl: mvebu: add pinctrl driver for Armada XP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit e5447d2609 upstream.
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: ce3ed59dcd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 438881dfdd upstream.
Due to a mistake, the CS0 and CS1 SPI0 functions were incorrectly
named "spi0-1" instead of just "spi0". This commit fixes that.
This DT binding change does not affect any of the in-tree users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: 5f597bb2be ("pinctrl: mvebu: add pinctrl driver for Armada 370")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 331642fbf2 upstream.
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Fixes: ca6d9a084b ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit c5272a2856 upstream.
Way back, when the world was a simpler place and there was no war, no
evil, and no kernel bugs, there was just a single pinctrl lock. That
was how the world was when (57291ce pinctrl: core device tree mapping
table parsing support) was written. In that case, there were
instances where the pinctrl mutex was already held when
pinctrl_register_map() was called, hence a "locked" parameter was
passed to the function to indicate that the mutex was already locked
(so we shouldn't lock it again).
A few years ago in (42fed7b pinctrl: move subsystem mutex to
pinctrl_dev struct), we switched to a separate pinctrl_maps_mutex.
...but (oops) we forgot to re-think about the whole "locked" parameter
for pinctrl_register_map(). Basically the "locked" parameter appears
to still refer to whether the bigger pinctrl_dev mutex is locked, but
we're using it to skip locks of our (now separate) pinctrl_maps_mutex.
That's kind of a bad thing(TM). Probably nobody noticed because most
of the calls to pinctrl_register_map happen at boot time and we've got
synchronous device probing. ...and even cases where we're
asynchronous don't end up actually hitting the race too often. ...but
after banging my head against the wall for a bug that reproduced 1 out
of 1000 reboots and lots of looking through kgdb, I finally noticed
this.
Anyway, we can now safely remove the "locked" parameter and go back to
a war-free, evil-free, and kernel-bug-free world.
Fixes: 42fed7ba44 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 4ff0f034e9 upstream.
The right check for conf_reg to be invalid it testing against -1 not 0
as is done in the rest of the driver.
This fixes an oops that can be triggered by:
cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/*
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16:
- file rename: drivers/pinctrl/freescale/pinctrl-imx.c ->
drivers/pinctrl/pinctrl-imx.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit 41f632fe17 upstream.
Remove bogus call to of_gpiochip_add (and of_gpio_chip remove in error
path) which is also called when adding the gpio chip.
This prevents adding the same pinctrl range twice.
Fixes: 3f8c50c9b1 ("OF: pinctrl: MIPS: lantiq: implement lantiq/xway
pinctrl support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit db93facfb0 upstream.
This patch is to fix two deadlock cases.
Deadlock 1:
CPU #1
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #0
pinctrl_unregister
(Holding lock pinctrldev_list_mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
Simply to say
CPU#1 is holding lock A and trying to acquire lock B,
CPU#0 is holding lock B and trying to acquire lock A.
Deadlock 2:
CPU #3
pinctrl_register-> pinctrl_get ->
create_pinctrl
(Holding lock pinctrl_maps_mutex)
-> get_pinctrl_dev_from_devname
(Trying to acquire lock pinctrldev_list_mutex)
CPU #2
pinctrl_unregister
(Holding lock pctldev->mutex)
-> pinctrl_put ->> pinctrl_free ->
pinctrl_dt_free_maps -> pinctrl_unregister_map
(Trying to acquire lock pinctrl_maps_mutex)
CPU #0
tegra_gpio_request
(Holding lock pinctrldev_list_mutex)
-> pinctrl_get_device_gpio_range
(Trying to acquire lock pctldev->mutex)
Simply to say
CPU#3 is holding lock A and trying to acquire lock D,
CPU#2 is holding lock B and trying to acquire lock A,
CPU#0 is holding lock D and trying to acquire lock B.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
commit d90c338189 upstream.
Even if a gpio pin is set to output, we still need to set INPUT_EN
functionality (by clearing INPUT_EN bit) to be able to read the pin's
level.
E.g. without this change, we'll always read low level state from sysfs.
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
st_gpio_irqmux_handler() reads the status register to find out
which banks inside the controller have pending IRQs.
For each banks having pending IRQs, it calls the corresponding handler.
Problem is that current code restricts the number of possible banks inside the
controller to ST_GPIO_PINS_PER_BANK. This define represents the number of pins
inside a bank, so it shouldn't be used here.
On STiH407, PIO_FRONT0 controller has 10 banks, so IRQs pending in the two
last banks (PIO18 & PIO19) aren't handled.
This patch replace ST_GPIO_PINS_PER_BANK by the number of banks inside the
controller.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org> #v3.15+
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are returning success here because PTR_ERR(NULL) is zero. We should
be returning -ENODEV.
Fixes: 3de68d331c ('pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kzalloc can fail. Add a null check to avoid null pointer
dereference error while accessing the pointer later.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
development cycle:
- Antoine Tenart made the get_group_pins() vtable entry
optional.
- Antoine also provides an entirely new driver for the
Marvell Berlin SoC. This is unrelated to the existing
MVEBU hardware driver and warrants its own separate
driver.
- Reflected from the GPIO subsystem there is a number of
refactorings to make pin control drivers with gpiochips
use the new gpiolib irqchip helpers. The following
drivers were converted to use the new infrastructure:
- ST Microelectronics STiH416 and friends
- The Atmel AT91
- The CSR SiRF (Prima2)
- The Qualcomm MSM series
- Massive improvements in the Qualcomm MSM driver from
Bjorn Andersson, Andy Gross and Kumar Gala. Among those
new support for the IPQ8064 and MSM8x74 SoC variants.
- Support for the Freescale i.MX6 SoloX SoC variant.
- Massive improvements in the Allwinner sunxi driver from
Boris Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori
Morimoto, Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from
Stepgen Warren.
- The Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- The MVEBU driver now supports the Orion5x SoC
variants, which is part of the effort of getting rid of
the old Marvell kludges in arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- A ton of cleanups and janitorial patches from Axel Lin.
- Some minor fixes and improvements here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wGE5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next
Pull pin control changes from Linus Walleij:
"This is the bulk of pin control changes for the v3.16 development
cycle:
- Antoine Tenart made the get_group_pins() vtable entry optional.
- Antoine also provides an entirely new driver for the Marvell Berlin
SoC. This is unrelated to the existing MVEBU hardware driver and
warrants its own separate driver.
- reflected from the GPIO subsystem there is a number of refactorings
to make pin control drivers with gpiochips use the new gpiolib
irqchip helpers. The following drivers were converted to use the
new infrastructure:
* ST Microelectronics STiH416 and friends
* The Atmel AT91
* The CSR SiRF (Prima2)
* The Qualcomm MSM series
- massive improvements in the Qualcomm MSM driver from Bjorn
Andersson, Andy Gross and Kumar Gala. Among those new support for
the IPQ8064 and MSM8x74 SoC variants.
- support for the Freescale i.MX6 SoloX SoC variant.
- massive improvements in the Allwinner sunxi driver from Boris
Brezillon, Maxime Ripard and Chen-Yu Tsai.
- Renesas PFC updates from Laurent Pinchart, Kuninori Morimoto,
Wolfram Sang and Magnus Damm.
- Cleanups and refactorings of the nVidia Tegra driver from Stepgen
Warren.
- the Exynos driver now supports the Exynos3250 SoC.
- Intel BayTrail updates from Jin Yao, Mika Westerberg.
- the MVEBU driver now supports the Orion5x SoC variants, which is
part of the effort of getting rid of the old Marvell kludges in
arch/arm/mach-orion5x
- Rockchip driver updates from Heiko Stuebner.
- a ton of cleanups and janitorial patches from Axel Lin.
- some minor fixes and improvements here and there"
* tag 'pinctrl-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (93 commits)
pinctrl: sirf: fix a bad conflict resolution
pinctrl: msm: Add more MSM8X74 pin definitions
pinctrl: qcom: ipq8064: Fix naming convention
pinctrl: msm: Add missing sdc1 and sdc3 groups
pinctrl: sirf: switch to using allocated state container
pinctrl: Enable "power-source" to be extracted from DT files
pinctrl: sunxi: create irq/pin mapping during init
pinctrl: pinconf-generic: Use kmemdup instead of kmalloc + memcpy
pinctrl: berlin: Use devm_ioremap_resource()
pinctrl: sirf: fix typo for GPIO bank number
pinctrl: sunxi: depend on RESET_CONTROLLER
pinctrl: sunxi: fix pin numbers passed to register offset helpers
pinctrl: add pinctrl driver for imx6sx
pinctrl/at91: Fix lockup when IRQ on PIOC and PIOD occurs
pinctrl: msm: switch to using generic GPIO irqchip helpers
pinctrl: sunxi: Fix multiple registration issue
pinctrl: sunxi: Fix recursive dependency
pinctrl: berlin: add the BG2CD pinctrl driver
pinctrl: berlin: add the BG2 pinctrl driver
pinctrl: berlin: add the BG2Q pinctrl driver
...
