[ Upstream commit da321133b5 ]
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbe (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbe (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 26bac95aa8 ]
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit 2e9dcdae40 upstream.
In case CLK_GATE_HIWORD_MASK flag is passed to clk_register_gate(), the bit #
should be no higher than 15, however the corresponding check is obviously off-
by-one.
Fixes: 045779942c ("clk: gate: add CLK_GATE_HIWORD_MASK")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 76820fcf7a upstream.
For all pll-s on sun6i n == 0 means use a multiplier of 1, rather then 0 as
it means on sun4i / sun5i / sun7i. n_start = 1 is already correctly set
for sun6i pll6, but was missing for pll1, this commit fixes this.
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52bba9809a upstream.
Some of the clks can be registered & unregistered before the clk related debugfs
entries are initialized at late_initcall. In the unregister path checking for only
dentry before clk_debug_init() would lead dangling pointers in the debug clk list,
because the list is already populated in register path and the clk pointer freed in
unregister path.
The side effect of not removing it from the list is either a null pointer
dereference or if lucky to boot the system, the number of clk entries in
debugfs disappear.
We could add more checks like if (inited && !clk->dentry) but just removing
the check for dentry made more sense as debugfs_remove_recursive() seems to be
safe with null pointers. This will ensure that the unregistering clk would be
removed from the debug list in all the code paths.
Without this patch kernel would crash with log:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0204000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Tainted: G B 3.19.0-rc3-00007-g412f9ba-dirty #840
Hardware name: Qualcomm (Flattened Device Tree)
task: ed948000 ti: ed944000 task.ti: ed944000
PC is at strlen+0xc/0x40
LR is at __create_file+0x64/0x1dc
pc : [<c04ee604>] lr : [<c049f1c4>] psr: 60000013
sp : ed945e40 ip : ed945e50 fp : ed945e4c
r10: 00000000 r9 : c1006094 r8 : 00000000
r7 : 000041ed r6 : 00000000 r5 : ed4af998 r4 : c11b5e28
r3 : 00000000 r2 : ed945e38 r1 : a0000013 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5787d Table: 8020406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xed944248)
Stack: (0xed945e40 to 0xed946000)
5e40: ed945e7c ed945e50 c049f1c4 c04ee604 c0fc2fa4 00000000 ecb748c0 c11c2b80
5e60: c0beec04 0000011c c0fc2fa4 00000000 ed945e94 ed945e80 c049f3e0 c049f16c
5e80: 00000000 00000000 ed945eac ed945e98 c08cbc50 c049f3c0 ecb748c0 c11c2b80
5ea0: ed945ed4 ed945eb0 c0fc3080 c08cbc30 c0beec04 c107e1d8 ecdf0600 c107e1d8
5ec0: c107e1d8 ecdf0600 ed945f54 ed945ed8 c0208ed4 c0fc2fb0 c026a784 c04ee628
5ee0: ed945f0c ed945ef0 c0f5d600 c04ee604 c0f5d5ec ef7fcc7d c0b40ecc 0000011c
5f00: ed945f54 ed945f10 c026a994 c0f5d5f8 c04ecc00 00000007 ef7fcc95 00000007
5f20: c0e90744 c0dd0884 ed945f54 c106cde0 00000007 c117f8c0 0000011c c0f5d5ec
5f40: c1006094 c100609c ed945f94 ed945f58 c0f5de34 c0208e50 00000007 00000007
5f60: c0f5d5ec be9b5ae0 00000000 c117f8c0 c0af1680 00000000 00000000 00000000
5f80: 00000000 00000000 ed945fac ed945f98 c0af169c c0f5dd2c ed944000 00000000
5fa0: 00000000 ed945fb0 c020f298 c0af168c 00000000 00000000 00000000 00000000
5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ebcc6d33 bfffca73
[<c04ee604>] (strlen) from [<c049f1c4>] (__create_file+0x64/0x1dc)
[<c049f1c4>] (__create_file) from [<c049f3e0>] (debugfs_create_dir+0x2c/0x34)
[<c049f3e0>] (debugfs_create_dir) from [<c08cbc50>] (clk_debug_create_one+0x2c/0x16c)
[<c08cbc50>] (clk_debug_create_one) from [<c0fc3080>] (clk_debug_init+0xdc/0x144)
[<c0fc3080>] (clk_debug_init) from [<c0208ed4>] (do_one_initcall+0x90/0x1e0)
[<c0208ed4>] (do_one_initcall) from [<c0f5de34>] (kernel_init_freeable+0x114/0x1e0)
[<c0f5de34>] (kernel_init_freeable) from [<c0af169c>] (kernel_init+0x1c/0xfc)
[<c0af169c>] (kernel_init) from [<c020f298>] (ret_from_fork+0x14/0x3c)
Code: c0b40ecc e1a0c00d e92dd800 e24cb004 (e5d02000)
---[ end trace b940e45b5e25c1e7 ]---
Fixes: 6314b6796e "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dccfecdb8 upstream.
The CPU_2X clock does not have a classical in-kernel user, but is,
amongst other things, required for OCM and debug access. Make sure this
clock is not mistakenly disabled during boot up by enabling it in the
platform's clock driver.
Fixes: 0ee52b157b 'clk: zynq: Add clock controller driver'
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dca1a4b5ff upstream.
All slow clk users are not properly claiming it (get + prepare + enable)
before using it.
If all users properly claiming this clock release it, the clock is
disabled, but faulty users still depends on it, and the system hangs.
This fix prevents the slow clock from being disabled, and should solve the
hanging issue, but offending drivers should be patched to properly claim
this clock.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b71e8ecd57 upstream.
The "smemc" clock is removed on BG2Q SoCs. In fact, bit19 of clkenable
register is for nfc. Current code use bit19 for non-exist "smemc"
incorrectly, this prevents eMMC from working due to the sdhci's
"core" clk is still gated.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12551f0239 upstream.
The bit locations indicating the locking status of the plls on rk3066 are
shifted by one to the right when compared to the rk3188, bits [7:4] instead
of [8:5] on the rk3188, thus indicating the locking state of the wrong pll
or a completely different information in case of the gpll.
The recently introduced pll init code exposed that problem on some rk3066
boards when it tried to bring the boot-pll value in line with the value
from the rate table.
Fix this by defining separate pll definitions for rk3066 with the correct
locking indices.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 2c14736c75 ("clk: rockchip: add clock driver for rk3188 and rk3066 clocks")
Tested-by: FUKAUMI Naoki <naobsd@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9880d4277f upstream.
Commit 0e5bdb3f9f (clk: rockchip: switch to using the new cpuclk type
for armclk) didn't take into account that the divider used on rk3288
are of the (n+1) type.
The rk3066 and rk3188 socs use more complex divider types making it
necessary for the list-elements to be the real register-values to write.
Therefore reduce divider values in the table accordingly so that they
really are the values that should be written to the registers and match
the dividers actually specified for the rk3288.
Reported-by: Sonny Rao <sonnyrao@chromium.org>
Fixes: 0e5bdb3f9f ("clk: rockchip: switch to using the new cpuclk type for armclk")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 176a107b86 upstream.
This reverts commit da788acb28.
That commit tried to fix the section mismatch warning by moving the
ppc_corenet_clk_driver struct to init section. This is definitely wrong
because the kernel would free the memories occupied by this struct
after boot while this driver is still registered in the driver core.
The kernel would panic when accessing this driver struct.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10cdfe54da upstream.
As __clk_release could call kfree on clk and then we wouldn't have a safe way
of getting the module that owns the clock.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Fixes: fcb0ee6a3d ("clk: Implement clk_unregister")
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f7e9de59 upstream.
Commit 6314b6796e (clk: Don't hold prepare_lock across debugfs
creation, 2014-09-04) forgot to update one place where we hold
the prepare_lock while creating debugfs directories. This means
we still have the chance of a deadlock that the commit was trying
to fix. Actually fix it by moving the debugfs creation outside
the prepare_lock.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: 6314b6796e "clk: Don't hold prepare_lock across debugfs creation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: removed lockdep_assert]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to check the A bit of CCCR for memory frequency
calculations, where the shift of the bit index was missing, triggering a
wrong calculation of memory frequency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Commit 79c6ab5095 (clk: divider: add CLK_DIVIDER_READ_ONLY flag) in
v3.16 introduced the CLK_DIVIDER_READ_ONLY flag which caused the
recalc_rate() and round_rate() clock callbacks to be omitted.
However using this flag has the unfortunate side effect of causing the
clock recalculation code when a clock rate change is attempted to always
treat it as a pass-through clock, i.e. with a fixed divide of 1, which
may not be the case. Child clock rates are then recalculated using the
wrong parent rate.
Therefore instead of dropping the recalc_rate() and round_rate()
callbacks, alter clk_divider_bestdiv() to always report the current
divider as the best divider so that it is never altered.
For me the read only clock was the system clock, which divided the PLL
rate by 2, from which both the UART and the SPI clocks were divided.
Initial setting of the UART rate set it correctly, but when the SPI
clock was set, the other child clocks were miscalculated. The UART clock
was recalculated using the PLL rate as the parent rate, resulting in a
UART new_rate of double what it should be, and a UART which spewed forth
garbage when the rate changes were propagated.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Max Schwarz <max.schwarz@online.de>
Cc: <stable@vger.kernel.org> # v3.16+
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
There is a duplication in a clock name for apq8084 platform that causes
the following warning: "RBCPR_CLK_SRC" redefined
Resolve this by adding a MMSS_ prefix to this clock and making its name
coherent with msm8974 platform.
Fixes: 2b46cd23a5 ("clk: qcom: Add APQ8084 Multimedia Clock Controller (MMCC) support")
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
First check for rate == 0 in set_rate and round_rate to avoid div by zero.
Then, in order to get the closest rate, round all divisions to the closest
result instead of rounding them down.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
at91rm9200_clk_usb_set_rate might fail depending on the requested rate,
because the parent_rate / rate remainder is not necessarily zero.
Moreover, when rounding down the calculated rate we might alter the
divisor calculation and end up with an invalid divisor.
To solve those problems, accept a non zero remainder, and always round
division to the closest result.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
fixes and enhancements to existing drivers as well as new drivers. This
tag contains a bit more arch code than I usually take due to some OMAP2+
changes. Additionally it contains the restart notifier handlers which
are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree I
had to revert one patch and follow up with one more fix near the tip of
this tag. Some dead code is introduced but it will soon become live code
after 3.18-rc1 is released as the rest of the PXA family is converted
over to the common clock framework.
Another trend in this tag is that multiple vendors have started to push
the complexity of changing their CPU frequency into the clock driver,
whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to some
confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=w2rN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
Pull kbuild changes from Michal Marek:
- fix for handling dependencies of *-objs targets by Masahiro Yamada
- lots of cleanups in the kbuild machinery, also by Masahiro
- fixes for the kconfig build to use an UTF-8 capable ncurses library
if possible and to build on not-so-standard installs
- some more minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Do not reference *-n variables in the Makefile
kbuild: simplify build, clean, modbuiltin shorthands
kbuild: arm: Do not define "comma" twice
kbuild: remove obj-n and lib-n handling
kbuild: remove unnecessary variable initializaions
kbuild: remove unnecessary "obj- := dummy.o" trick
kbuild: handle C=... and M=... after entering into build directory
kbuild: use $(Q) for sub-make target
kbuild: fake the "Entering directory ..." message more simply
kconfig/lxdialog: get ncurses CFLAGS with pkg-config
kconfig: nconfig: fix multi-byte UTF handling
kconfig: lxdialog: fix spelling
kbuild: Make scripts executable
kbuild: remove redundant clean-files from scripts/kconfig/Makefile
kbuild: refactor script/kconfig/Makefile
kbuild: handle the dependency of multi-objs hostprogs appropriately
kbuild: handle multi-objs dependency appropriately
This is the initial version of the RK808 PMIC. This is a power management
IC for multimedia products. It provides regulators that are able to
supply power to processor cores and other components. The chip provides
other modules including RTC, Clockout.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com> says:
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
New and updated SoC support. Among the things new for this release are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still ongoing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAVDWVHWCrR//JCVInAQJQVw/+NEfKWh6blDvLEWHpkmBtzdsT3s+r1wwb
ATtvd1Q7RlOMEbzxc2J87tJ44yHb64mSPBbC4BCGuQsM5IIvM4potmBphl/XxLfd
b8PNcI6nvLO+FZOcgon0JWmvVnt+vLGKPUWzURXSRjdrpVRg2qyRpW+nPBnvX4HP
qyzlSskkYzKm7WJQrIV1K3yYwRLrVZdz4DuF340mSFy+4H+uci2Fw91HJ9lKKmPS
24Klx2Q4n6wfg946WazWtz21HjEBuMzRCq0CGZrwcTJffRyMxa4iq/kqE3xGbPtN
onuP1gmAM7UOMewEvc1ZLycY7JyZ3mhKnKduqS/QN2JLLQEY2v1iYFnEKP8mHnnw
ax6RVi91PC2MSLZyPcRtsegSKB9l16I7H+C5pgTOMgsSaqxSG1JtV1qZl3uwhBnE
GB45KHPvTFojrH2+CqneNTLET1ozKgwtuHkWTG61/puYeap/VlpRU2OWj2mQF2E0
SiBzmlbUBpSqzjFgVGD4ywKAuVA/WpJtaOB7Qg26GL2QoNKrY/wsUCY8hU742+jE
b/N6obGcpmjytLkFRHx+AbYc75DHXkPtF4CWawDeQFW30LUeixZJqewQ61a56QF8
49DbO6J+sR0n3xlteD49QdQJzDCtKw3BV+VQaFRcxqVDq4LJAxtUHJZ7c3iyvzEi
6Yt+PsqSP7Y=
=ZHtj
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Arnd Bergmann:
"New and updated SoC support. Among the things new for this release
are:
- at91: Added support for the new SAMA5D4 SoC, following the earlier
SAMA5D3
- bcm: Added support for BCM63XX family of DSL SoCs
- hisi: Added support for HiP04 server-class SoC
- meson: Initial support for the Amlogic Meson6 (aka 8726MX) platform
- shmobile: added support for new r8a7794 (R-Car E2) automotive SoC
Noteworthy changes to existing SoC support are:
- imx: convert i.MX1 to device tree
- omap: lots of power management work
- omap: base support to enable moving to standard UART driver
- shmobile: lots of progress for multiplatform support, still
ongoing"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (171 commits)
ARM: hisi: depend on ARCH_MULTI_V7
CNS3xxx: Fix debug UART.
ARM: at91: fix nommu build regression
ARM: meson: add basic support for MesonX SoCs
ARM: meson: debug: add debug UART for earlyprintk support
irq: Export handle_fasteoi_irq
ARM: mediatek: Add earlyprintk support for mt6589
ARM: hisi: Fix platmcpm compilation when ARMv6 is selected
ARM: debug: fix alphanumerical order on debug uarts
ARM: at91: document Atmel SMART compatibles
ARM: at91: add sama5d4 support to sama5_defconfig
ARM: at91: dt: add device tree file for SAMA5D4ek board
ARM: at91: dt: add device tree file for SAMA5D4 SoC
ARM: at91: SAMA5D4 SoC detection code and low level routines
ARM: at91: introduce basic SAMA5D4 support
clk: at91: add a driver for the h32mx clock
ARM: pxa3xx: provide specific platform_devices for all ssp ports
ARM: pxa: ssp: provide platform_device_id for PXA3xx
ARM: OMAP4+: Remove static iotable mappings for SRAM
ARM: OMAP4+: Move SRAM data to DT
...
Fix the building of pxa clock drivers so that the files are actually
compiled if and only if COMMON_CLK was selected by the architecture.
This prevents conflicts with mach-pxa clock legacy implementation.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In these Makefiles, at least one of "obj-y" and "obj-" is non-empty,
hence built-in.o is always created without such a trick.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au> [shmobile]
Acked-by: David S. Miller <davem@davemloft.net> [networking]
Signed-off-by: Michal Marek <mmarek@suse.cz>
and rockchip as well as s3c24xx restart handlers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUK/GYAAoJEPOmecmc0R2Bnc8IAJY3NpUhN2It0WqL1meeIDr7
jGVphxhiEsAlXMbHyO0V/LhUTbGtjfDotd43Y84cZW43R7G2ErvvBsWMKCff2xIB
cVtjXJ8JI+s2T/gBEssZDnhh1dcP04fnZ2LMdLCGudnmn2AyR2AXQQBqFiO+kQWe
0x2dsGgcQPn93X9i9sT03BKJTZjRoCZkUh0aJ2y+yL9Y5A9CNXCVGfJ5E1GNw3Px
ffeKA0OsOhUMw9aqb8fLvDuRd0mo1i+BSCaOeNTlwzASmxCUJ9MOOKtF/Khx7x2r
6N3w/EN4F8R+qJ/gOyZR9I3SrnLU1rMBOHvaSxDJb0RXAq5AROvQS1t4GiF2A68=
=bvGz
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Allow parent rate changes for i2s on rk3288
and rockchip as well as s3c24xx restart handlers.
S3C2412, S3C2443 and their derivatives contain a special software-reset
register in their system-controller.
Therefore register a restart handler for those.
Tested on a s3c2416-based board, s3c2412 compile-tested.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add infrastructure to write the correct value to the restart register and
register the restart notifier for both rk3188 (including rk3066) and rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The relation of i2s nodes as follows:
i2s_src 0 0 594000000 0
i2s_frac 0 0 11289600 0
i2s_pre 0 0 11289600 0
sclk_i2s0 0 0 11289600 0
i2s0_clkout 0 0 11289600 0
hclk_i2s0 1 1 99000000 0
sclk_i2s0 is the master clock, when to set rate of sclk_i2s0, should
allow to set its parent's rate, by add flag CLK_SET_RATE_PARENT for
"i2s_frac", "i2s_pre", "i2s0_clkout" and "sclk_i2s0".
Tested on rk3288 board using max98090, with command "aplay <music.wav>"
Change-Id: I12faad082566532b65a7de8c0a6845e1c17870e6
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Move pxa27x clock drivers from arch/arm/mach-pxa to driver/clk.
In the move :
- convert to new clock framework legacy clocks
- provide clocks as before for platform data based boards
- provide clocks through devicetree
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add a the common code used by all PXA variants.
This is the first step in the transition from architecture defined
clocks (in arch/arm/mach-pxa) towards clock framework. The goal is to
have the same features (and not all the features) of the existing
clocks, and enable the transition of PXA to device-tree.
All PXA rely on a "CKEN" type clock, which :
- has a gate (bit in CKEN register)
- is generated from a PLL, generally divided
- has an alternate low power clock
Each variant will specialize the CKEN clock :
- pxa25x have no low power clock
- pxa27x in low power use always the 13 MHz ring oscillator
- pxa3xx in low power have specific dividers for each clock
The device-tree provides a list of CLK_* (ex: CLK_USB or CLK_I2C) to get
a handle on the clock. While pxa-clock.h will describe all the clocks of
all the variants, each variant will only use a subset of it.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The gpio-gate clock uses the gpiod_ APIs but does not directly include the
header for them causing build failures in some configurations including ARM
allnoconfig. Include the header directly.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is safe to call the pm sync calls in interrupt context in this driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As written, the __init for ti_clk_get_div_table is in the middle of the return
type.
The gcc documentation indicates that section attributes should be added to the
end of the function declaration:
extern void foobar (void) __attribute__ ((section ("bar")));
However gcc seems to be very permissive with where attributes can be placed.
clang on the other hand isn't so permissive, and fails if you put the section
definition in the middle of the return type:
drivers/clk/ti/divider.c:298:28: error: expected ';' after struct
static struct clk_div_table
^
;
drivers/clk/ti/divider.c:298:1: warning: 'static' ignored on this
declaration [-Wmissing-declarations]
static struct clk_div_table
^
drivers/clk/ti/divider.c:299:9: error: type specifier missing,
defaults to 'int' [-Werror,-Wimplicit-int]
__init *ti_clk_get_div_table(struct device_node *node)
~~~~~~ ^
drivers/clk/ti/divider.c:345:9: warning: incompatible pointer types
returning 'struct clk_div_table *' from a function with result type 'int *' [-Wincompatible-pointer-types]
return table;
^~~~~
drivers/clk/ti/divider.c:419:9: warning: incompatible pointer types
assigning to 'const struct clk_div_table *' from 'int *' [-Wincompatible-pointer-types]
*table = ti_clk_get_div_table(node);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
3 warnings and 2 errors generated.
By convention, most of the kernel code puts section attributes between the
return type and function name. In the case where the return type is a pointer,
it's important to place the '*' on left of the __init.
This updated code works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
I "forgot" to update the dtb and the kernel crashed:
|Unable to handle kernel NULL pointer dereference at virtual address 0000002e
|PC is at __clk_get_flags+0x4/0xc
|LR is at ti_dt_clockdomains_setup+0x70/0xe8
because I did not have the clock nodes. of_clk_get() returns an error
pointer which is not checked here.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
of_clk_add_provider makes an internal copy of the parent_names property
while its called, thus it is no longer needed after this call and can
be freed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Previously, the TI clock driver initialized all the clocks hierarchically
under each separate clock provider node. Now, each clock that requires
IO access will instead check their parent node to find out which IO range
to use.
This patch allows the TI clock driver to use a few new features provided
by the generic of_clk_init, and also allows registration of clock nodes
outside the clock hierarchy (for example, any external clocks.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Stefan Assmann <sassmann@kpanic.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Support clk of sata, usb and ethernet
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Setting 'flags' to zero will be certainly a misleading way to avoid
warning of 'flags' may be used uninitialized. uninitialized_var is
a correct way because the warning is a false possitive.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The most important part of this serie is the addition of the phase API to
handle the MMC clocks in the Allwinner SoCs.
Apart from that, the A23 gained a new mbus driver, and there's a fix for a
incorrect divider table on the APB0 clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZkI9
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Allwinner Clocks Additions for 3.18
The most important part of this serie is the addition of the phase API to
handle the MMC clocks in the Allwinner SoCs.
Apart from that, the A23 gained a new mbus driver, and there's a fix for a
incorrect divider table on the APB0 clock.
