[ Upstream commit 391949b6f0 ]
With spidev the mesg->complete callback points to spidev_complete.
Calling this unblocks spidev_sync and so spidev_sync_write finishes. As
the struct spi_message just read is a local variable in
spidev_sync_write and recording the trace event accesses this message
the recording is better done first. The same can happen for
spidev_sync_read.
This fixes an oops observed on a 3.14-rt system with spidev activity
after
echo 1 > /sys/kernel/debug/tracing/events/spi/enable
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit cd6fa8d2ca ]
Commit fd316941c ("spi/pl022: disable port when unused") introduced a race,
which leads to possible driver lock up (easily reproducible on SMP).
The problem happens in giveback() function where the completion of the transfer
is signalled to SPI subsystem and then the HW SPI controller is disabled. Another
transfer might be setup in between, which brings driver in locked-up state.
Exact event sequence on SMP:
core0 core1
=> pump_transfers()
/* message->state == STATE_DONE */
=> giveback()
=> spi_finalize_current_message()
=> pl022_unprepare_transfer_hardware()
=> pl022_transfer_one_message
=> flush()
=> do_interrupt_dma_transfer()
=> set_up_next_transfer()
/* Enable SSP, turn on interrupts */
writew((readw(SSP_CR1(pl022->virtbase)) |
SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase));
...
=> pl022_interrupt_handler()
=> readwriter()
/* disable the SPI/SSP operation */
=> writew((readw(SSP_CR1(pl022->virtbase)) &
(~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase));
Lockup! SPI controller is disabled and the data will never be received. Whole
SPI subsystem is waiting for transfer ACK and blocked.
So, only signal transfer completion after disabling the controller.
Fixes: fd316941c (spi/pl022: disable port when unused)
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit c9dafb27c8 ]
When DMA descriptor allocation fails we should not try to assign any fields in
the bad descriptor. The patch adds the necessary checks for that.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 76e1d14b31 ]
Additionally to the current DMA transfer the PDC allows to set up a next DMA
transfer. This is useful for larger SPI transfers.
The driver currently waits for ENDRX as end of the transfer. But ENDRX is set
when the current DMA transfer is done (RCR = 0), i.e. it doesn't include the
next DMA transfer.
Thus a subsequent SPI transfer could be started although there is currently a
transfer in progress. This can cause invalid accesses to the SPI slave devices
and to SPI transfer errors.
This issue has been observed on a hardware with a M25P128 SPI NOR flash.
So instead of ENDRX we should wait for RXBUFF. This flag is set if there is
no more DMA transfer in progress (RCR = RNCR = 0).
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit a02bb401f8 upstream.
For TKT238285 hardware issue which may cause txfifo store data twice can only
be caught on i.mx6dl, we use pio mode instead of DMA mode on i.mx6dl.
Fixes: f62caccd12 (spi: spi-imx: add DMA support)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 973fbce69e upstream.
devm_* API was supposed to be used only in probe function call.
Memory is allocated at 'probe' and free automatically at 'remove'.
Usage of devm_* functions outside probe sometimes leads to memory leak.
Avoid using devm_kzalloc in dspi_setup_transfer and use kzalloc instead.
Also add the dspi_cleanup function to free the controller data upon
cleanup.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c957e8f084 upstream.
Once the current message is finished, the driver notifies SPI core about
this by calling spi_finalize_current_message(). This function queues next
message to be transferred. If there are more messages in the queue, it is
possible that the driver is asked to transfer the next message at this
point.
When spi_finalize_current_message() returns the driver clears the
drv_data->cur_chip pointer to NULL. The problem is that if the driver
already started the next message clearing drv_data->cur_chip will cause
NULL pointer dereference which crashes the kernel like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
IP: [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
PGD 78bb8067 PUD 37712067 PMD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 11 Comm: ksoftirqd/1 Tainted: G O 3.18.0-rc4-mjo #5
Hardware name: Intel Corp. VALLEYVIEW B3 PLATFORM/NOTEBOOK, BIOS MNW2CRB1.X64.0071.R30.1408131301 08/13/2014
task: ffff880077f9f290 ti: ffff88007a820000 task.ti: ffff88007a820000
RIP: 0010:[<ffffffffa0022bc8>] [<ffffffffa0022bc8>] cs_deassert+0x18/0x70 [spi_pxa2xx_platform]
RSP: 0018:ffff88007a823d08 EFLAGS: 00010202
RAX: 0000000000000008 RBX: ffff8800379a4430 RCX: 0000000000000026
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff8800379a4430
RBP: ffff88007a823d18 R08: 00000000ffffffff R09: 000000007a9bc65a
R10: 000000000000028f R11: 0000000000000005 R12: ffff880070123e98
R13: ffff880070123de8 R14: 0000000000000100 R15: ffffc90004888000
FS: 0000000000000000(0000) GS:ffff880079a80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000048 CR3: 000000007029b000 CR4: 00000000001007e0
Stack:
ffff88007a823d58 ffff8800379a4430 ffff88007a823d48 ffffffffa0022c89
0000000000000000 ffff8800379a4430 0000000000000000 0000000000000006
ffff88007a823da8 ffffffffa0023be0 ffff88007a823dd8 ffffffff81076204
Call Trace:
[<ffffffffa0022c89>] giveback+0x69/0xa0 [spi_pxa2xx_platform]
[<ffffffffa0023be0>] pump_transfers+0x710/0x740 [spi_pxa2xx_platform]
[<ffffffff81076204>] ? pick_next_task_fair+0x744/0x830
[<ffffffff81049679>] tasklet_action+0xa9/0xe0
[<ffffffff81049a0e>] __do_softirq+0xee/0x280
[<ffffffff81049bc0>] run_ksoftirqd+0x20/0x40
[<ffffffff810646df>] smpboot_thread_fn+0xff/0x1b0
[<ffffffff810645e0>] ? SyS_setgroups+0x150/0x150
[<ffffffff81060f9d>] kthread+0xcd/0xf0
[<ffffffff81060ed0>] ? kthread_create_on_node+0x180/0x180
[<ffffffff8187a82c>] ret_from_fork+0x7c/0xb0
Fix this by clearing drv_data->cur_chip before we call spi_finalize_current_message().
Reported-by: Martin Oldfield <m@mjoldfield.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67bf9cda4b upstream.
The FIFO size is 40 accordingly to the specifications, but this means 0x40,
i.e. 64 bytes. This patch fixes the typo and enables FIFO size autodetection
for Intel MID devices.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d297933cc7 upstream.
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 015760563e upstream.
SH-MSIOF driver is enabled autosuspend API of spi framework.
But autosuspend framework doesn't work during initializing.
So runtime PM lock is added in SH-MSIOF driver initializing.
Fixes: e2a0ba547b (spi: sh-msiof: Convert to spi core auto_runtime_pm framework)
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c328a262f ("spi: sirf: Avoid duplicate code in various
bits_per_word cases") is wrong in setting data width register of
fifo is not right, it should use sspi->word_width >> 1 to set
related bits. According to hardware spec, the mapping between
register value and data width:
0 - byte
1 - WORD
2 - DWORD
Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
We can only use page_address on memory that has been mapped using kmap,
when the buffer passed to the SPI has been allocated by vmalloc the page
has not necessarily been mapped through kmap. This means sometimes
page_address will return NULL causing the pointer we pass to sg_set_buf
to be invalid.
As we only call page_address so that we can pass a virtual address to
sg_set_buf which will then immediately call virt_to_page on it, fix this
by calling sg_set_page directly rather then relying on the sg_set_buf
helper.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If PM_RUNTIME is enabled, it is easy to trigger the following backtrace
on pxa2xx hosts:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104
[<c000de68>] (unwind_backtrace) from [<c000c078>] (show_stack+0x10/0x14)
[<c000c078>] (show_stack) from [<c001d75c>] (warn_slowpath_common+0x6c/0x8c)
[<c001d75c>] (warn_slowpath_common) from [<c001d818>] (warn_slowpath_null+0x1c/0x24)
[<c001d818>] (warn_slowpath_null) from [<c0015e80>] (clk_disable+0xa0/0xa8)
[<c0015e80>] (clk_disable) from [<c02507f8>] (pxa2xx_spi_suspend+0x2c/0x34)
[<c02507f8>] (pxa2xx_spi_suspend) from [<c0200360>] (platform_pm_suspend+0x2c/0x54)
[<c0200360>] (platform_pm_suspend) from [<c0207fec>] (dpm_run_callback.isra.14+0x2c/0x74)
[<c0207fec>] (dpm_run_callback.isra.14) from [<c0209254>] (__device_suspend+0x120/0x2f8)
[<c0209254>] (__device_suspend) from [<c0209a94>] (dpm_suspend+0x50/0x208)
[<c0209a94>] (dpm_suspend) from [<c00455ac>] (suspend_devices_and_enter+0x8c/0x3a0)
[<c00455ac>] (suspend_devices_and_enter) from [<c0045ad4>] (pm_suspend+0x214/0x2a8)
[<c0045ad4>] (pm_suspend) from [<c04b5c34>] (test_suspend+0x14c/0x1dc)
[<c04b5c34>] (test_suspend) from [<c000880c>] (do_one_initcall+0x8c/0x1fc)
[<c000880c>] (do_one_initcall) from [<c04aecfc>] (kernel_init_freeable+0xf4/0x1b4)
[<c04aecfc>] (kernel_init_freeable) from [<c0378078>] (kernel_init+0x8/0xec)
[<c0378078>] (kernel_init) from [<c0009590>] (ret_from_fork+0x14/0x24)
---[ end trace 46524156d8faa4f6 ]---
This happens because suspend function tries to disable a clock that is
already disabled by runtime_suspend callback. Add if
(!pm_runtime_suspended()) checks to suspend/resume path.
Fixes: 7d94a50585 (spi/pxa2xx: add support for runtime PM)
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the
lower 2 bits of the chip select to select a CTAR register.
SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values
if the chip selects 4/5 are used. For those chip selects SPI_CTAR even
calculated offsets of non-existing registers.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
In rx mode, dma must be prepared before spi is enabled.
But in tx and tr mode, spi must be enabled first.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the minimum divisor in rk3x's spi controller is 2,
if spi_clk is less than 2 * sclk_out, we can't get the right divisor.
So we must set spi_clk again to match slave request.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When mapped RX DMA entries are unmapped in an error condition when DMA
is firstly configured in the driver, the number of TX DMA entries was
passed in, which is incorrect
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
By using separate TX and RX bounce buffers, we avoid potential cache
flush and invalidation sequence issue that may be encountered when a
single bounce buffer is shared between TX and RX
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
The of_node element must be initialized to enable discovery of node
children which takes place in the of_register_spi_devices() function.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Though intel-mid-dma does not follow a new DMA workflow (*) let's prepare SPI
DW driver for that.
(*) The client is obliged to call dma_async_issue_pending() which starts the
actual transfers. Old DMA drivers do not follow this, since requirement was
introduced in the discussion of [1].
[1] http://www.spinics.net/lists/arm-kernel/msg125987.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of direct dereference to dmaengine callbacks we are going to use
DMAengine wrappers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using magic numbers in the code we create a bit map definition of
the DMACR register and use it.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
This change introduces (and documents) a new device tree compatible
device name "armada-370-spi" to support this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly to fix missing MODULE_LICENSE.
Also add MODULE_DESCRIPTION and MODULE_AUTHOR.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
config SPI_BCM53XX needs to depend on BCMA_POSSIBLE and select BCMA.
This fixes below build error:
ERROR: "bcma_driver_unregister" [drivers/spi/spi-bcm53xx.ko] undefined!
ERROR: "__bcma_driver_register" [drivers/spi/spi-bcm53xx.ko] undefined!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In my test on RK3288-pinky board, if spi is enabled, it will begin to
read data from slave regardless of whether the DMA is ready. So we
need prepare DMA before spi is enable.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Remove the probe info message which also has wrong output. No need to add
KERN_INFO to pr_info. Output was:
6Freescale DSPI master initialized
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a extended PL022 which has an extra register for controlling up
to five chip select signals. This controller is found on the AXM5516 SoC.
Unfortunately the PrimeCell identification registers are identical to a
standard ARM PL022. To work around this, the peripheral ID must be overridden
in the device tree using the "arm,primecell-periphid" property with the value
0x000b6022.
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
