[ Upstream commit 15e3d5a285 ]
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race")
Reported-by: Tóth Attila <atoth@atoth.sote.hu>
Tested-by: Tóth Attila <atoth@atoth.sote.hu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 537b604c8b ]
b9d5c6b7ef ("[SCSI] cleanup setting task state in
scsi_error_handler()") has introduced a race between scsi_error_handler
and scsi_host_dev_release resulting in the hang when the device goes
away because scsi_error_handler might miss a wake up:
CPU0 CPU1
scsi_error_handler scsi_host_dev_release
kthread_stop()
kthread_should_stop()
test_bit(KTHREAD_SHOULD_STOP)
set_bit(KTHREAD_SHOULD_STOP)
wake_up_process()
wait_for_completion()
set_current_state(TASK_INTERRUPTIBLE)
schedule()
The most straightforward solution seems to be to invert the ordering of
the set_current_state and kthread_should_stop.
The issue has been noticed during reboot test on a 3.0 based kernel but
the current code seems to be affected in the same way.
[jejb: additional comment added]
Cc: <stable@vger.kernel.org> # 3.6+
Reported-and-debugged-by: Mike Mayer <Mike.Meyer@teradata.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5116fbf136 ]
Didn't check for less-than-or-equal zero. Means we may later call
scsi_dma_unmap() even though we don't have valid mappings.
Signed-off-by: Dick Kennedy <dick.kennedy@avagotech.com>
Signed-off-by: James Smart <james.smart@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 49718f0fb8 ]
The routines in scsi_rpm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by calling the block layer's runtime-PM
routines only if the device's driver really does have a runtime-PM
callback routine. Since ses doesn't define any such callbacks, the
crash won't occur.
This fixes Bugzilla #101371.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Stanisław Pitucha <viraptor@gmail.com>
Reported-by: Ilan Cohen <ilanco@gmail.com>
Tested-by: Ilan Cohen <ilanco@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 4f258a4634 ]
Commit bcdb247c6b ("sd: Limit transfer length") clamped the maximum
size of an I/O request to the MAXIMUM TRANSFER LENGTH field in the BLOCK
LIMITS VPD. This had the unfortunate effect of also limiting the maximum
size of non-filesystem requests sent to the device through sg/bsg.
Avoid using blk_queue_max_hw_sectors() and set the max_sectors queue
limit directly.
Also update the comment in blk_limits_max_hw_sectors() to clarify that
max_hw_sectors defines the limit for the I/O controller only.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Brian King <brking@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 660d0831d1 ]
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Chris Leech <cleech@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f6979adeaa ]
Due to patch "libfc: Do not invoke the response handler after
fc_exch_done()" (commit ID 7030fd62) the lport_recv() call
in fc_exch_recv_req() is passed a dangling pointer. Avoid this
by moving the fc_frame_free() call from fc_invoke_resp() to its
callers. This patch fixes the following crash:
general protection fault: 0000 [#3] PREEMPT SMP
RIP: fc_lport_recv_req+0x72/0x280 [libfc]
Call Trace:
fc_exch_recv+0x642/0xde0 [libfc]
fcoe_percpu_receive_thread+0x46a/0x5ed [fcoe]
kthread+0x10a/0x120
ret_from_fork+0x42/0x70
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7d2cce58a7 ]
Fix a couple of pci id table mistakes:
Subdevice ID 0x3323 missing from product[] table
(another name for HP Smart Storage 1210m)
Bogus 0x1925 subdevice id removed from hpsa_pci_device_id[] (no such thing.)
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 451a2886b6 ]
unfortunately, allowing an arbitrary 16bit value means a possibility of
overflow in the calculation of total number of pages in bio_map_user_iov() -
we rely on there being no more than PAGE_SIZE members of sum in the
first loop there. If that sum wraps around, we end up allocating
too small array of pointers to pages and it's easy to overflow it in
the second loop.
X-Coverup: TINC (and there's no lumber cartel either)
Cc: stable@vger.kernel.org # way, way back
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 3f1c058131 ]
Fixes another signed / unsigned array indexing bug in the ipr driver.
Currently, when hrrq_index wraps, it becomes a negative number. We
do the modulo, but still have a negative number, so we end up indexing
backwards in the array. Given where the hrrq array is located in memory,
we probably won't actually reference memory we don't own, but nonetheless
ipr is still looking at data within struct ipr_ioa_cfg and interpreting it as
struct ipr_hrr_queue data, so bad things could certainly happen.
Each ipr adapter has anywhere from 1 to 16 HRRQs. By default, we use 2 on new
adapters. Let's take an example:
Assume ioa_cfg->hrrq_index=0x7fffffffe and ioa_cfg->hrrq_num=4:
The atomic_add_return will then return -1. We mod this with 3 and get -2, add
one and get -1 for an array index.
On adapters which support more than a single HRRQ, we dedicate HRRQ to adapter
initialization and error interrupts so that we can optimize the other queues
for fast path I/O. So all normal I/O uses HRRQ 1-15. So we want to spread the
I/O requests across those HRRQs.
With the default module parameter settings, this bug won't hit, only when
someone sets the ipr.number_of_msix parameter to a value larger than 3 is when
bad things start to happen.
Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bb7c54339e ]
When ipr's internal driver trace was changed to an atomic, a signed/unsigned
bug slipped in which results in us indexing backwards in our memory buffer
writing on memory that does not belong to us. This patch fixes this by removing
the modulo and instead just mask off the low bits.
Cc: <stable@vger.kernel.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 36b8e180e1 ]
Make sure we have the host lock held when calling scsi_report_bus_reset. Fixes
a crash seen as the __devices list in the scsi host was changing as we were
iterating through it.
Cc: <stable@vger.kernel.org>
Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 35e9a9f939 ]
This works around a issue with qnap iscsi targets not handling large IOs
very well.
The target returns:
VPD INQUIRY: Block limits page (SBC)
Maximum compare and write length: 1 blocks
Optimal transfer length granularity: 1 blocks
Maximum transfer length: 4294967295 blocks
Optimal transfer length: 4294967295 blocks
Maximum prefetch, xdread, xdwrite transfer length: 0 blocks
Maximum unmap LBA count: 8388607
Maximum unmap block descriptor count: 1
Optimal unmap granularity: 16383
Unmap granularity alignment valid: 0
Unmap granularity alignment: 0
Maximum write same length: 0xffffffff blocks
Maximum atomic transfer length: 0
Atomic alignment: 0
Atomic transfer length granularity: 0
and it is *sometimes* able to handle at least one IO of size up to 8 MB. We
have seen in traces where it will sometimes work, but other times it
looks like it fails and it looks like it returns failures if we send
multiple large IOs sometimes. Also it looks like it can return 2 different
errors. It will sometimes send iscsi reject errors indicating out of
resources or it will send invalid cdb illegal requests check conditions.
And then when it sends iscsi rejects it does not seem to handle retries
when there are command sequence holes, so I could not just add code to
try and gracefully handle that error code.
The problem is that we do not have a good contact for the company,
so we are not able to determine under what conditions it returns
which error and why it sometimes works.
So, this patch just adds a new black list flag to set targets like this to
the old max safe sectors of 1024. The max_hw_sectors changes added in 3.19
caused this regression, so I also ccing stable.
Reported-by: Christian Hesse <list@eworm.de>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 45c44b5ff9 ]
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit be34c62ddf ]
Introduce the helper function srp_wait_for_queuecommand().
Move the definition of scsi_request_fn_active(). Add a comment
above srp_wait_for_queuecommand() that support for scsi-mq needs
to be added.
This patch does not change any functionality. A second call to
srp_wait_for_queuecommand() will be introduced in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: James Bottomley <JBottomley@Odin.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com>
Cc: <stable@vger.kernel.org> #v3.13
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 74856fbf44 ]
256 bytes per sector support has been broken since 2.6.X,
and no-one stepped up to fix this.
So disable support for it.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit dc45708ca9 ]
Set the SRB flags correctly when there is no data transfer. Without this
change some IHV drivers will fail valid commands such as TEST_UNIT_READY.
Cc: <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 579d69bc1f ]
The 3w-sas driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Torsten Luettgert <ml-lkml@enda.eu>
Tested-by: Bernd Kardatzki <Bernd.Kardatzki@med.uni-tuebingen.de>
Cc: stable@vger.kernel.org
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 118c855b56 ]
The 3w-9xxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 9cd9554615 ]
The 3w-xxxx driver needs to tear down the dma mappings before returning
the command to the midlayer, as there is no guarantee the sglist and
count are valid after that point. Also remove the dma mapping helpers
which have another inherent race due to the request_id index.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 56cbd0ccc1 ]
mvsas is giving a General protection fault when it encounters an expander
attached ATA device. Analysis of mvs_task_prep_ata() shows that the driver is
assuming all ATA devices are locally attached and obtaining the phy mask by
indexing the local phy table (in the HBA structure) with the phy id. Since
expanders have many more phys than the HBA, this is causing the index into the
HBA phy table to overflow and returning rubbish as the pointer.
mvs_task_prep_ssp() instead does the phy mask using the port properties.
Mirror this in mvs_task_prep_ata() to fix the panic.
Reported-by: Adam Talbot <ajtalbot1@gmail.com>
Tested-by: Adam Talbot <ajtalbot1@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e557990e35 ]
3aec2f41a8 introduced a merge error where we would end up check for
sdkp instead of sdkp->ATO. Fix this so we register app tag capability
correctly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e727c42bd5 ]
The new integrity code did not correctly unregister the profile for SD
disks. Call blk_integrity_unregister() when we release a disk.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # v3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 8de580742f ]
We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2e7cee027b ]
Kernel panic was happening as iscsi_host_remove() was called on
a host which was not yet added.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bba0bdd7ad ]
SCSI transport drivers and SCSI LLDs block a SCSI device if the
transport layer is not operational. This means that in this state
no requests should be processed, even if the REQ_PREEMPT flag has
been set. This patch avoids that a rescan shortly after a cable
pull sporadically triggers the following kernel oops:
BUG: unable to handle kernel paging request at ffffc9001a6bc084
IP: [<ffffffffa04e08f2>] mlx4_ib_post_send+0xd2/0xb30 [mlx4_ib]
Process rescan-scsi-bus (pid: 9241, threadinfo ffff88053484a000, task ffff880534aae100)
Call Trace:
[<ffffffffa0718135>] srp_post_send+0x65/0x70 [ib_srp]
[<ffffffffa071b9df>] srp_queuecommand+0x1cf/0x3e0 [ib_srp]
[<ffffffffa0001ff1>] scsi_dispatch_cmd+0x101/0x280 [scsi_mod]
[<ffffffffa0009ad1>] scsi_request_fn+0x411/0x4d0 [scsi_mod]
[<ffffffff81223b37>] __blk_run_queue+0x27/0x30
[<ffffffff8122a8d2>] blk_execute_rq_nowait+0x82/0x110
[<ffffffff8122a9c2>] blk_execute_rq+0x62/0xf0
[<ffffffffa000b0e8>] scsi_execute+0xe8/0x190 [scsi_mod]
[<ffffffffa000b2f3>] scsi_execute_req+0xa3/0x130 [scsi_mod]
[<ffffffffa000c1aa>] scsi_probe_lun+0x17a/0x450 [scsi_mod]
[<ffffffffa000ce86>] scsi_probe_and_add_lun+0x156/0x480 [scsi_mod]
[<ffffffffa000dc2f>] __scsi_scan_target+0xdf/0x1f0 [scsi_mod]
[<ffffffffa000dfa3>] scsi_scan_host_selected+0x183/0x1c0 [scsi_mod]
[<ffffffffa000edfb>] scsi_scan+0xdb/0xe0 [scsi_mod]
[<ffffffffa000ee13>] store_scan+0x13/0x20 [scsi_mod]
[<ffffffff811c8d9b>] sysfs_write_file+0xcb/0x160
[<ffffffff811589de>] vfs_write+0xce/0x140
[<ffffffff81158b53>] sys_write+0x53/0xa0
[<ffffffff81464592>] system_call_fastpath+0x16/0x1b
[<00007f611c9d9300>] 0x7f611c9d92ff
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 75c3d0bf9c ]
This patch fixes the incorrect use of __transport_register_session()
in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform
explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list
to add new se_sess nodes.
Given that tcm_qla2xxx_check_initiator_node_acl() is not called with
qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the
code should be using transport_register_session() instead.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
commit f76a610a8b upstream.
In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.
[ 29.406183] ------------[ cut here ]------------
[ 29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: Minh Tran <minh.tran@emulex.com>
Fixes: 6733b39a13
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7772855a99 upstream.
With scsi-mq enabled, userspace programs can get unexpected EWOULDBLOCK
(a.k.a. EAGAIN) errors when submitting commands to the SCSI generic
driver. Fix by calling blk_get_request() with GFP_KERNEL instead of
GFP_ATOMIC.
Note: to avoid introducing a potential deadlock, this patch should be
applied after the patch titled "sg: fix unkillable I/O wait deadlock
with scsi-mq".
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7568615c10 upstream.
When using the write()/read() interface for submitting commands, the
SCSI generic driver does not call blk_put_request() on a completed SCSI
command until userspace calls read() to get the command completion.
Since scsi-mq uses a fixed number of preallocated requests, this makes
it possible for userspace to exhaust the entire preallocated supply of
requests. For places in the kernel that call blk_get_request() with
GFP_KERNEL, this can cause the calling process to deadlock in a
permanent unkillable I/O wait in blk_get_request() -> ... -> bt_get().
For places in the kernel that call blk_get_request() with GFP_ATOMIC,
this can cause blk_get_request() always to return -EWOULDBLOCK. Note
that these problems happen only if scsi-mq is enabled. Prevent the
problems by calling blk_put_request() as soon as the SCSI command
completes instead of waiting for userspace to call read().
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2ced1719a upstream.
Update driver "mask_interrupts" before enable/disable hardware interrupt
in order to avoid missing interrupts because of "mask_interrupts" still
set to 1 and hardware interrupts are enabled.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab2f0608e1 upstream.
This patch will address the issue of SCSI device created at OS level for
non existing VD. ldTgtIdtoLd[] array has size 256 for Extended VD firmware
and 128 for legacy firmware. Accessing indices beyond array size (OS will
send TUR, INQUIRY.. commands upto device index 255), may return valid LD
value and that particular SCSI command will be SUCCESS and creating SCSI
device for non existing target(VD).
For legacy firmware (64 VD firmware), invalidates LD (by setting LD value
to 0xff) in LdTgtIdtoLd[] array for device index beyond 127, so that
invalid LD(0xff) value should be returned beyond device index beyond 127.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 200aed582d upstream.
This patch addresses below issues:
1) Few endianness bug fixes.
2) Break the iteration after (MAX_LOGICAL_DRIVES_EXT - 1)),
instead of MAX_LOGICAL_DRIVES_EXT.
3) Optimization in MFI INIT frame before firing.
4) MFI IO frame should be 256bytes aligned. Code is optimized to reduce
the size of frame for fusion adapters and make the MFI frame size
calculation a bit transparent and readable.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a9794d329 upstream.
The following patch fixes an issue observed with 4k sector disks
where the max_hw_sectors attribute was getting set too large in
sd_revalidate_disk. Since sdkp->max_xfer_blocks is in units
of SCSI logical blocks and queue_max_hw_sectors is in units of
512 byte blocks, on a 4k sector disk, every time we went through
sd_revalidate_disk, we were taking the current value of
queue_max_hw_sectors and increasing it by a factor of 8. Fix
this by only shifting sdkp->max_xfer_blocks.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cdb08172b upstream.
Fixes a race condition in abort handling that was injected
when multiple interrupt support was added. When only a single
interrupt is present, the adapter guarantees it will send
responses for aborted commands prior to the response for the
abort command itself. With multiple interrupts, these responses
generally come back on different interrupts, so we need to
ensure the abort thread waits until the aborted command is
complete so we don't perform a double completion. This race
condition was being hit frequently in environments which
were triggering command timeouts, which was resulting in
a double completion causing a kernel oops.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: Wendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e86fb5e8ab upstream.
When ring buffer returns an error indicating retry, storvsc may not
return a proper error code to SCSI when bounce buffer is not used.
This has introduced I/O freeze on RAID running atop storvsc devices.
This patch fixes it by always returning a proper error code.
Signed-off-by: Long Li <longli@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 511833acfc upstream.
Commit ac61d19559 (scsi: set correct completion code in
scsi_send_eh_cmnd()) introduced a bug. It changed the stored return
value from a queuecommand call, but it didn't take into account that
the return value was used again later on. This patch fixes the bug by
changing the later usage.
There is a big comment in the middle of scsi_send_eh_cmnd() which
does a good job of explaining how the routine works. But it mentions
a "rtn = FAILURE" value that doesn't exist in the code. This patch
adjusts the code to match the comment (I assume the comment is right
and the code is wrong).
This fixes Bugzilla #88341.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Tested-by: Андрей Аладьев <aladjev.andrew@gmail.com>
Fixes: ac61d19559
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 120bb3e1e3 upstream.
This fixes random memory corruption triggered when all three of the
following are true:
* scsi-mq enabled
* T10 Protection Information (DIF) enabled
* SCSI host with sg_tablesize > SCSI_MAX_SG_SEGMENTS (128)
The symptoms of this bug are unpredictable memory corruption, BUG()s,
oopses, lockups, etc., any of which may appear to be completely
unrelated to the root cause.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198a956a11 upstream.
The Microsoft iSCSI target does not support REPORT SUPPORTED OPERATION
CODES. Blacklist these devices so we don't attempt to send the command.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Mike Christie <michaelc@cs.wisc.edu>
Reported-by: jazz@deti74.ru
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2311ce4d9c upstream.
This reverts commit 963ba22b90
("mpt3sas: Remove phys on topology change")
Reverting the previous mpt3sas drives patch changes,
since we will observe below issue
Issue:
Drives connected Enclosure/Expander will unregister with
SCSI Transport Layer, if any one remove and add expander
cable with in DMD (Device Missing Delay) time period or
even any one power-off and power-on the Enclosure with in
the DMD period.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a89c2d89 upstream.
This reverts commit 3520f9c779
("mpt2sas: Remove phys on topology change")
Reverting the previous mpt2sas drives patch changes,
since we will observe below issue
Issue:
Drives connected Enclosure/Expander will unregister with
SCSI Transport Layer, if any one remove and add expander
cable with in DMD (Device Missing Delay) time period or
even any one power-off and power-on the Enclosure with in
the DMD period.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c92b7e0a upstream.
The .eh_abort_handler needs to return SUCCESS, FAILED, or
FAST_IO_FAIL. So fixup all callers to adhere to this requirement.
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a set of ten fixes: 8 for UFS including four static checker warnings,
a potential null deref in the voltage regulator code, a race on module unload,
a ref counting fix on the well known LUNs which made it impossible to remove
the ufs module and fix to correct the information in pwr_info. In addition to
UFS, there's a blacklist for the Intel Multi-Flex array which chokes on report
supported operation codes and a fix to an oops in bnx2fc caused by shared
skbs.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUeXohAAoJEDeqqVYsXL0MKUMH/3/+cCrlKRHlYxY7wB3/7J4+
iVF5zC75598YAXfFWSkQqcITRsL8Azd7A+hd58a1JDNaA3VrpGW0E5fEYcBekJB9
wzbOPeAfq0G7hPfJ2nIP8exuJAAo84bHB3XmcduT0QubqfnQib1QG7oxX8qcGYP7
PeP/aXGYe/b7E9m7xSAxuYsnvc/XZwKqmGcIdkvf+GRbke1DYR+52zYWa4alwgiY
mKLZwn3LOOOGlYqbu6B1m4/Swfv1r5weWCtDXnHaX1Hy/wMZCR+GUtVfm+Qh3EXs
5vLSk7BPNnTS/WEe/z3qYmnPAvFcEe7Z0fKxHxQT/n1F4AdvLds/B98C871UtiQ=
=VKAj
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of ten fixes: 8 for UFS including four static checker
warnings, a potential null deref in the voltage regulator code, a race
on module unload, a ref counting fix on the well known LUNs which made
it impossible to remove the ufs module and fix to correct the
information in pwr_info.
In addition to UFS, there's a blacklist for the Intel Multi-Flex array
which chokes on report supported operation codes and a fix to an oops
in bnx2fc caused by shared skbs"
[ For us non-SCSI people: "UFS" here is "Universal Flash Storage" not
the filesystem. - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
ufs: fix NULL dereference when no regulators are defined
ufs: ensure clk gating work is finished before module unloading
scsi: ufs: fix static checker warning in ufshcd_parse_clock_info
scsi: ufs: fix static checker warning in __ufshcd_setup_clocks
scsi: ufs: fix static checker warning in ufshcd_populate_vreg
scsi: ufs: fix static checker errors in ufshcd_system_suspend
ufs: fix power info after link start-up
ufs: fix reference counting of W-LUs
scsi: add Intel Multi-Flex to scsi scan blacklist
bnx2fc: do not add shared skbs to the fcoe_rx_list
If no voltage supply regulators are defined for the UFS devices (assumed
they are always-on), ufshcd_config_vreg_load() can be called on
suspend/resume paths with vreg == NULL as hba->vreg_info.vcc* equal to
NULL, and it causes NULL pointer dereference.
This fixes it by making ufshcd_config_vreg_{h,l}pm noop when no regulators
are defined.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
