[ Upstream commit 3c25a860d1 ]
Commit fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 68242a5a1e ]
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit b2663a4f30 ]
When the IP stack passes SKBs the sfc driver puts them in 2 different TX
queues (called partners), one for checksummed and one for not checksummed.
If the SKB has xmit_more set the driver will delay pushing the work to the
NIC.
When later it does decide to push the buffers this patch ensures it also
pushes the partner queue, if that also has any delayed work. Before this
fix the work in the partner queue would be left for a long time and cause
a netdev watchdog.
Fixes: 70b33fb ("sfc: add support for skb->xmit_more")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 0db65fcfcd ]
New device IDs shamelessly lifted from the vendor driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 48900cb6af ]
virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.
A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.
Drop NETIF_F_FRAGLIST so we only get what we can handle.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7091079173 ]
The lt4112 is a HP branded Huawei me906e modem. Like other Huawei
modems, it does not have a fixed interface to function mapping.
Instead it uses a Huawei specific scheme: functions are mapped by
subclass and protocol.
However, the HP vendor ID is used for modems from many different
manufacturers using different schemes, so we cannot apply a generic
vendor rule like we do for the Huawei vendor ID.
Replace the previous lt4112 entry pointing to an arbitrary interface
number with a device specific subclass + protocol match.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Fixes: bb2bdeb83f ("qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e6dbe1eb2d ]
priv->hwts_*_en indicate if timestamping is enabled/disabled at run
time. But priv->dma_cap.time_stamp and priv->dma_cap.atime_stamp
indicates HW is support for PTPv1/PTPv2.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit c02b05011f ]
When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1acea4f6ce ]
We can't rely on PPPOX_ZOMBIE to decide whether to clear po->pppoe_dev.
PPPOX_ZOMBIE can be set by pppoe_disc_rcv() even when po->pppoe_dev is
NULL. So we have no guarantee that (sk->sk_state & PPPOX_ZOMBIE) implies
(po->pppoe_dev != NULL).
Since we're releasing a PPPoE socket, we want to release the pppoe_dev
if it exists and reset sk_state to PPPOX_DEAD, no matter the previous
value of sk_state. So we can just check for po->pppoe_dev and avoid any
assumption on sk->sk_state.
Fixes: 2b018d57ff ("pppoe: drop PPPOX_ZOMBIEs in pppoe_release")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f23d538bc2 ]
We don't have fraglist support in TAP_FEATURES. This will lead
software segmentation of gro skb with frag list. Fixes by having
frag list support in TAP_FEATURES.
With this patch single session of netperf receiving were restored from
about 5Gb/s to about 12Gb/s on mlx4.
Fixes a567dd6252 ("macvtap: simplify usage of tap_features")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1d20a16062 ]
drivers/net/ethernet/sfc/selftest.c: In function ‘efx_iterate_state’:
drivers/net/ethernet/sfc/selftest.c:388:9: warning: passing argument 1 of ‘memcpy’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
This is because the msg[] member of struct efx_loopback_payload
is marked as 'const'. Remove that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f08f625876 ]
Add 3 new subdevice IDs for the 0x095A device ID and 2 for the 0x095B
device ID.
Cc: <stable@vger.kernerl.org> [3.13+]
Reported-by: Jeremy <jeremy.bomkamp@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2cf5eb3ab7 ]
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 3fd0d3c170 ]
Identify 7265-D devices using the hardware revision (they have the
same PCI IDs as 7265) and change the configuration for them taking
the differences (currently only the firmware image) into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit b5a48134f8 ]
The MODULE_FIRMWARE() for 3160 should be using the 7260 version as
it's done in the device configuration struct instead of referencing
IWL3160_UCODE_API_OK which doesn't even exist.
Cc: <stable@vger.kernel.org> [3.8+]
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5bd166872d ]
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 029cd03702 ]
ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 6423fc3416 ]
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5e55e3cbd1 ]
The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.
Fixes: 767d34fc67 ("ath10k: remove DMA mapping wrappers")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d2eac98f7d ]
The SF2 driver currently overrides speed settings for its port
configured using a fixed PHY, this is both unnecessary and incorrect,
because we keep feedback to the hardware parameters that we read from
the PHY device, which in the case of a fixed PHY cannot possibly change
speed.
This is a required change to allow the fixed PHY code to allow
registering a PHY with a link configured as DOWN by default and avoid
some sort of circular dependency where we require the link_update
callback to run to program the hardware, and we then utilize the fixed
PHY parameters to program the hardware with the same settings.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 03679a1473 ]
The macro to write 64-bits quantities to the 32-bits register swapped
the value and offsets arguments, we want to preserve the ordering of the
arguments with respect to how writel() is implemented for instance:
value first, offset/base second.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 4548a697e4 ]
tse_poll() calls __napi_complete() with irq enabled. This leads napi
poll_list corruption and may stop all napi drivers working.
Use napi_complete() instead of __napi_complete().
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 72ddef0506 ]
When initializing igb driver (e.g. 82576, I350), IGB_FLAG_QUEUE_PAIRS is
set if adapter->rss_queues exceeds half of max_rss_queues in
igb_init_queue_configuration().
On the other hand, IGB_FLAG_QUEUE_PAIRS is not set even if the number of
queues exceeds half of max_combined in igb_set_channels() when changing
the number of queues by "ethtool -L".
In this case, if numvecs is larger than MAX_MSIX_ENTRIES (10), the size
of adapter->msix_entries[], an overflow can occur in
igb_set_interrupt_capability(), which in turn leads to an oops.
Fix this problem as follows:
- When changing the number of queues by "ethtool -L", set
IGB_FLAG_QUEUE_PAIRS in the same way as initializing igb driver.
- When increasing the size of q_vector, reallocate it appropriately.
(With IGB_FLAG_QUEUE_PAIRS set, the size of q_vector gets larger.)
Another possible way to fix this problem is to cap the queues at its
initial number, which is the number of the initial online cpus. But this
is not the optimal way because we cannot increase queues when another
cpu becomes online.
Note that before commit cd14ef54d2 ("igb: Change to use statically
allocated array for MSIx entries"), this problem did not cause oops
but just made the number of queues become 1 because of entering msi_only
mode in igb_set_interrupt_capability().
Fixes: 907b783579 ("igb: Add ethtool support to configure number of channels")
CC: stable <stable@vger.kernel.org>
Signed-off-by: Shota Suzuki <suzuki_shota_t3@lab.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 251086f588 ]
In routine _rtl8821ae_set_media_status(), an incorrect mask results in a test
for AP status to always be false. Similar bugs were fixed in rtl8192cu and
rtl8192de, but this instance was missed at that time.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit ade4dc3e61 ]
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f50791ac1a ]
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d3d11fe08c ]
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf4 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1c1bf34951 ]
The port-change event processing in procedure mlx4_eq_int() uses "slave"
as the vf_oper array index. Since the value of "slave" is the PF function
index, the result is that the PF link state is used for deciding to
propagate the event for all the VFs. The VF link state should be used,
so the VF function index should be used here.
Fixes: 948e306d7d ('net/mlx4: Add VF link state support')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit a951bc1e6b ]
The "follow" fail_over_mac policy is useful for multiport devices that
either become confused or incur a performance penalty when multiple
ports are programmed with the same MAC address, but the same MAC
address still may happened by this steps for this policy:
1) echo +eth0 > /sys/class/net/bond0/bonding/slaves
bond0 has the same mac address with eth0, it is MAC1.
2) echo +eth1 > /sys/class/net/bond0/bonding/slaves
eth1 is backup, eth1 has MAC2.
3) ifconfig eth0 down
eth1 became active slave, bond will swap MAC for eth0 and eth1,
so eth1 has MAC1, and eth0 has MAC2.
4) ifconfig eth1 down
there is no active slave, and eth1 still has MAC1, eth2 has MAC2.
5) ifconfig eth0 up
the eth0 became active slave again, the bond set eth0 to MAC1.
Something wrong here, then if you set eth1 up, the eth0 and eth1 will have the same
MAC address, it will break this policy for ACTIVE_BACKUP mode.
This patch will fix this problem by finding the old active slave and
swap them MAC address before change active slave.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 06f6d1094a ]
When the bonding is being unloaded and the netdevice notifier is
unregistered it executes NETDEV_UNREGISTER for each device which should
remove the bond's proc entry but if the device enslaved is not of
ARPHRD_ETHER type and is in front of the bonding, it may execute
bond_release_and_destroy() first which would release the last slave and
destroy the bond device leaving the proc entry and thus we will get the
following error (with dynamic debug on for bond_netdev_event to see the
events order):
[ 908.963051] eql: event: 9
[ 908.963052] eql: IFF_SLAVE
[ 908.963054] eql: event: 2
[ 908.963056] eql: IFF_SLAVE
[ 908.963058] eql: event: 6
[ 908.963059] eql: IFF_SLAVE
[ 908.963110] bond0: Releasing active interface eql
[ 908.976168] bond0: Destroying bond bond0
[ 908.976266] bond0 (unregistering): Released all slaves
[ 908.984097] ------------[ cut here ]------------
[ 908.984107] WARNING: CPU: 0 PID: 1787 at fs/proc/generic.c:575
remove_proc_entry+0x112/0x160()
[ 908.984110] remove_proc_entry: removing non-empty directory
'net/bonding', leaking at least 'bond0'
[ 908.984111] Modules linked in: bonding(-) eql(O) 9p nfsd auth_rpcgss
oid_registry nfs_acl nfs lockd grace fscache sunrpc crct10dif_pclmul
crc32_pclmul crc32c_intel ghash_clmulni_intel ppdev qxl drm_kms_helper
snd_hda_codec_generic aesni_intel ttm aes_x86_64 glue_helper pcspkr lrw
gf128mul ablk_helper cryptd snd_hda_intel virtio_console snd_hda_codec
psmouse serio_raw snd_hwdep snd_hda_core 9pnet_virtio 9pnet evdev joydev
drm virtio_balloon snd_pcm snd_timer snd soundcore i2c_piix4 i2c_core
pvpanic acpi_cpufreq parport_pc parport processor thermal_sys button
autofs4 ext4 crc16 mbcache jbd2 hid_generic usbhid hid sg sr_mod cdrom
ata_generic virtio_blk virtio_net floppy ata_piix e1000 libata ehci_pci
virtio_pci scsi_mod uhci_hcd ehci_hcd virtio_ring virtio usbcore
usb_common [last unloaded: bonding]
[ 908.984168] CPU: 0 PID: 1787 Comm: rmmod Tainted: G W O
4.2.0-rc2+ #8
[ 908.984170] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 908.984172] 0000000000000000 ffffffff81732d41 ffffffff81525b34
ffff8800358dfda8
[ 908.984175] ffffffff8106c521 ffff88003595af78 ffff88003595af40
ffff88003e3a4280
[ 908.984178] ffffffffa058d040 0000000000000000 ffffffff8106c59a
ffffffff8172ebd0
[ 908.984181] Call Trace:
[ 908.984188] [<ffffffff81525b34>] ? dump_stack+0x40/0x50
[ 908.984193] [<ffffffff8106c521>] ? warn_slowpath_common+0x81/0xb0
[ 908.984196] [<ffffffff8106c59a>] ? warn_slowpath_fmt+0x4a/0x50
[ 908.984199] [<ffffffff81218352>] ? remove_proc_entry+0x112/0x160
[ 908.984205] [<ffffffffa05850e6>] ? bond_destroy_proc_dir+0x26/0x30
[bonding]
[ 908.984208] [<ffffffffa057540e>] ? bond_net_exit+0x8e/0xa0 [bonding]
[ 908.984217] [<ffffffff8142f407>] ? ops_exit_list.isra.4+0x37/0x70
[ 908.984225] [<ffffffff8142f52d>] ?
unregister_pernet_operations+0x8d/0xd0
[ 908.984228] [<ffffffff8142f58d>] ?
unregister_pernet_subsys+0x1d/0x30
[ 908.984232] [<ffffffffa0585269>] ? bonding_exit+0x23/0xdba [bonding]
[ 908.984236] [<ffffffff810e28ba>] ? SyS_delete_module+0x18a/0x250
[ 908.984241] [<ffffffff81086f99>] ? task_work_run+0x89/0xc0
[ 908.984244] [<ffffffff8152b732>] ?
entry_SYSCALL_64_fastpath+0x16/0x75
[ 908.984247] ---[ end trace 7c006ed4abbef24b ]---
Thus remove the proc entry manually if bond_release_and_destroy() is
used. Because of the checks in bond_remove_proc_entry() it's not a
problem for a bond device to change namespaces (the bug fixed by the
Fixes commit) but since commit
f939981492 ("bonding: Don't allow bond devices to change network
namespaces.") that can't happen anyway.
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: a64d49c3dd ("bonding: Manage /proc/net/bonding/ entries from
the netdev events")
Tested-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 741e3b9902 ]
The driver code allows for the disabling of MSI interrupts; however the
module_parm line was missed and the option fails to show with modinfo.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.15+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 36c01245eb ]
As reported by Manfred Schlaegl here
http://marc.info/?l=linux-netdev&m=143482089824232&w=2
commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
As net timestamping is influenced by several players (netstamp_needed and
netdev_tstamp_prequeue) Manfred missed a proper timestamp which leads to
CAN frame loss.
As skb timestamping became now mandatory for CAN related skbs this patch
makes sure that received CAN skbs always have a proper timestamp set.
Maybe there's a better solution in the future but this patch fixes the
CAN frame loss so far.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit eb686231fc ]
When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 488a9b48e3 ]
Indication of a single completed packet, marked by txbbs_skipped
being bigger then zero, in not enough in order to wake up a
stopped TX queue. The completed packet may contain a single TXBB,
while next packet to be sent (after the wake up) may have multiple
TXBBs (LSO/TSO packets for example), causing overflow in queue followed
by WQE corruption and TX queue timeout.
Instead, wake the stopped queue only when there's enough room for the
worst case (maximum sized WQE) packet that we should need to handle after
the queue is opened again.
Also created an helper routine - mlx4_en_is_tx_ring_full, which checks
if the current TX ring is full or not. It provides better code readability
and removes code duplication.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit b65657fc24 ]
The Ethernet controller found in the Armada 370, 380 and 385 SoCs don't
support TCP/IP checksumming with frame sizes larger than 1600 bytes.
This patch fixes the issue by disabling the features NETIF_F_IP_CSUM and
NETIF_F_TSO for the Armada 370 and compatibles SoCs when the MTU is set
to a value greater than 1600 bytes.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f522a975a8 ]
The mvneta driver supports the Ethernet IP found in the Armada 370, XP,
380 and 385 SoCs. Since at least one more hardware feature is available
for the Armada XP SoCs then a way to identify them is needed.
This patch introduces a new compatible string "marvell,armada-xp-neta".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f1590670ce ]
Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:
[1] On driver probe underlying memory allocated with
dma_alloc_coherent() might not be zeroed and so
it will be filled with garbage.
[2] During driver operation some bits could be set by SD/MMC
controller (for example error flags etc).
And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.
This change addresses both items above with:
[1] Use of dma_zalloc_coherent() instead of simple
dma_alloc_coherent() to make sure allocated memory is
zeroed. That shouldn't affect performance because
this allocation only happens once on driver probe.
[2] Do explicit zeroing of both "des0" and "des1" fields
of all buffer descriptors during initialization of
DMA transfer.
And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 300f77c08d ]
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 1277fa2ab2 ]
Several of these drivers have there TX randomly blocked for 3~5 seconds while
measuring tx throughput (iperf). The root couse happens in rtl_pci_flush().
The function uses a while-loop to wait for TX queue length to decrease to 0.
The TX queue length counts the number of packets that are queued in the driver.
The driver relys on the TX OK interrupt to return skb and reduce TX queue length.
The interrupt subroutine disables interupts, reads the interrupt registers, and
then clears the registers in the beginning of _rtl_pci_interrupt(). After all
interupts process are finished, the driver invokes enable_interrupt() to enable
interupts. This behavior is normal for an interrupt subroutine.
But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt
clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX
queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in
unterminated while-loop.
This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.18+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 90f91b1298 ]
It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 59d2d18cc4 ]
If CONFIG_ARCH_DMA_ADDR_T_64BIT enabled for x86 systems and physical
memory is more than 4GB, dma_map_page may return a valid memory
address which greater than 0xffffffff. As a result, the mlx5 device page
allocator RB tree will be initialized with valid addresses greater than
0xfffffff.
However, (addr & PAGE_MASK) set the high four bytes to zeros. So, it's
impossible for the function, free_4k, to release the pages whose
addresses greater than 4GB. Memory leaks. And mlx5_ib module can't
release the pages when user try to remove the module, as a result,
system hang.
[root@rdma05 root]# dmesg | grep addr | head
addr = 3fe384000
addr & PAGE_MASK = fe384000
[root@rdma05 root]# rmmod mlx5_ib <---- hang on
---------------------- cosnole log -----------------
mlx5_ib 0000:04:00.0: irq 138 for MSI/MSI-X
alloc irq_desc for 139 on node -1
alloc kstat_irqs on node -1
mlx5_ib 0000:04:00.0: irq 139 for MSI/MSI-X
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
0000:04:00.0:free_4k:221:(pid 1519): page not found
---------------------- cosnole log -----------------
Fixes: bf0bf77f65 ('mlx5: Support communicating arbitrary host page size to firmware')
Signed-off-by: Honggang Li <honli@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e51000db4c ]
There are several places in the driver (all in control paths) where
coherent dma memory is being allocated using either dma_alloc_coherent()
or the deprecated pci_alloc_consistent(). All these calls should be
changed to use dma_zalloc_coherent() to avoid uninitialized fields in
data structures backed by this memory.
Reported-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 31a418986a ]
When we come to tear things down in netback_remove() and generate the
uevent it is possible that the xenstore directory has already been
removed (details below).
In such cases netback_uevent() won't be able to read the hotplug
script and will write a xenstore error node.
A recent change to the hypervisor exposed this race such that we now
sometimes lose it (where apparently we didn't ever before).
Instead read the hotplug script configuration during setup and use it
for the lifetime of the backend device.
The apparently more obvious fix of moving the transition to
state=Closed in netback_remove() to after the uevent does not work
because it is possible that we are already in state=Closed (in
reaction to the guest having disconnected as it shutdown). Being
already in Closed means the toolstack is at liberty to start tearing
down the xenstore directories. In principal it might be possible to
arrange to unregister the device sooner (e.g on transition to Closing)
such that xenstore would still be there but this state machine is
fragile and prone to anger...
A modern Xen system only relies on the hotplug uevent for driver
domains, when the backend is in the same domain as the toolstack it
will run the necessary setup/teardown directly in the correct sequence
wrt xenstore changes.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit ce0e5c522d ]
Commit e9ce7cb6b1 ("xen-netback: Factor queue-specific data into queue
struct") introduced a regression when moving queue-specific data into
the queue struct by failing to set the credit_bytes field. This
prevented bandwidth limiting from working. Initialize the field as it
was done before multiqueue support was added.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit adbe088f6f ]
A pair of nested spin locks was introduced in commit 63502b8d0
"dp83640: Fix receive timestamp race condition".
Unfortunately the 'flags' parameter was reused for the inner lock,
clobbering the originally saved IRQ state. This patch fixes the issue
by changing the inner lock to plain spin_lock without irqsave.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit a935865c82 ]
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
