[ Upstream commit 7045c3689f ]
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9 ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 255f0e7c41 ]
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
Cc: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Clarify why we need this. Also remove the now unused "dev"
local variable to appease gcc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.com
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7ccca1d5bf ]
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Cc: stable@vger.kernel.org
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2700818ac9 ]
LPT is pch, so might run into the fdi bandwidth constraint (especially
since it has only 2 lanes). But right now we just force pipe_bpp back
to 24, resulting in a nice loop (which we bail out with a loud
WARN_ON). Fix this.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93477
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462264381-7573-1-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit f58a1acc7e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5eaa60c710 ]
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c417 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com
(cherry picked from commit bf93ba67e9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 49e6bc51bc ]
When we suspend we turn everything off so the pps should be idle, and we
also (or at least should) disable all power wells which will reset the
power sequencer port assignment. So when we resume all power sequencers
should be in their reset state. However it's at least theoretically
possible that the BIOS would touch the power seuqencer(s), so to be safe
we ought to read out the current port assignment like we do at driver
init time.
To do that we can simply call vlv_initial_power_sequencer_setup() from
the encoder ->reset() hook before calling intel_edp_panel_vdd_sanitize().
There's no danger or clobbering the pps delays since we now have those
stored within intel_dp and we don't change them once initialized.
This will make sure that the vdd state gets correctly tracked post-resume
in case the BIOS enabled it.
We need to shuffle things around a bit to get the locking right, and
while at it, make intel_edp_panel_vdd_sanitize() static and move it
around a bit to avoid a forward declaration.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 9dc0487d96 ]
Some hubs are forgetful, and end up forgetting whatever GUID we set
previously after we do a suspend/resume cycle. This can lead to
hotplugging breaking (along with probably other things) since the hub
will start sending connection notifications with the wrong GUID. As
such, we need to check on resume whether or not the GUID the hub is
giving us is valid.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460580618-7421-1-git-send-email-cpaul@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 263efde31f ]
We can thank KASAN for finding this, otherwise I probably would have spent
hours on it. This fixes a somewhat harder to trigger kernel panic, occuring
while enabling MST where the port we were currently updating the payload on
would have all of it's refs dropped before we finished what we were doing:
==================================================================
BUG: KASAN: use-after-free in drm_dp_update_payload_part1+0xb3f/0xdb0 [drm_kms_helper] at addr ffff8800d29de018
Read of size 4 by task Xorg/973
=============================================================================
BUG kmalloc-2048 (Tainted: G B W ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper] age=16477 cpu=0 pid=2175
___slab_alloc+0x472/0x490
__slab_alloc+0x20/0x40
kmem_cache_alloc_trace+0x151/0x190
drm_dp_add_port+0x1aa/0x1ed0 [drm_kms_helper]
drm_dp_send_link_address+0x526/0x960 [drm_kms_helper]
drm_dp_check_and_send_link_address+0x1ac/0x210 [drm_kms_helper]
drm_dp_mst_link_probe_work+0x77/0xd0 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
INFO: Freed in drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper] age=7521 cpu=0 pid=2175
__slab_free+0x17f/0x2d0
kfree+0x169/0x180
drm_dp_free_mst_port+0x50/0x60 [drm_kms_helper]
drm_dp_destroy_connector_work+0x2b8/0x490 [drm_kms_helper]
process_one_work+0x562/0x1350
worker_thread+0xd9/0x1390
kthread+0x1c5/0x260
ret_from_fork+0x22/0x40
which on this T460s, would eventually lead to kernel panics in somewhat
random places later in intel_mst_enable_dp() if we got lucky enough.
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit b5dcec693f ]
Allowing userptr bo which are basicly a list of page from some vma
(so either anonymous page or file backed page) would lead to serious
corruption of kernel structures and counters (because we overwrite
the page->mapping field when mapping buffer).
This will already block if the buffer was populated before anyone does
try to mmap it because then TTM_PAGE_FLAG_SG would be set in in the
ttm_tt flags. But that flag is check before ttm_tt_populate in the ttm
vm fault handler.
So to be safe just add a check to verify_access() callback.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bfaddd9fc8 ]
This reverts commit e64c952efb.
ATPX is the ACPI method for controlling AMD PowerXpress laptops.
There are flags to indicate which methods are supported. If
the dGPU power down flag is not supported, the driver needs to
implement the dGPU power down manually. We had previously
always forced the driver to assume the ATPX dGPU power down
was present, but this causes problems on boards where it is
not, leading to GPU hangs when attempting to power down the
dGPU. Manual dGPU power down is not currently supported in
the Linux driver. Some laptops indicate that the ATPX
dGPU power down method is not present, but it actually
apparently is. I'm not sure if this is a bios bug and it should
be set or if there is a reason it was unset and the method should
not be used. This is not an issue on other OSes since both the
ATPX and the manual driver power down methods are supported.
This is apparently fairly widespread, so just revert for now.
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=115321https://bugzilla.kernel.org/show_bug.cgi?id=116581https://bugzilla.kernel.org/show_bug.cgi?id=116251
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d59a1f71ff ]
The SPICE protocol considers the position of a cursor to be the location
of its active pixel on the display, so the cursor is drawn with its
top-left corner at "(x - hot_spot_x, y - hot_spot_y)" but the DRM cursor
position gives the location where the top-left corner should be drawn,
with the hotspot being a hint for drivers that need it.
This fixes the location of the window resize cursors when using Fluxbox
with the QXL DRM driver and both the QXL and modesetting X drivers.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1447845445-2116-1-git-send-email-john@metanate.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bb26270ed2 ]
These are just two wrappers to be used in the MST code later.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 459ee1c3fd ]
As observed on Apple iMac10,1, DCE-3.2, RV-730,
link rate of 2.7 Ghz is not selected, because
the args.v1.ucConfig flag setting for 2.7 Ghz
gets overwritten by a following assignment of
the transmitter to use.
Move link rate setup a few lines down to fix this.
In practice this didn't have any positive or
negative effect on display setup on the tested
iMac10,1 so i don't know if backporting to stable
makes sense or not.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit e64c952efb ]
Some PX laptops don't provide an ACPI method to control dGPU power. On
those systems, the driver is responsible for handling the dGPU power
state. Disable runtime PM on them until support for this is implemented.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 256faedcfd ]
This reverts commit dbb17a21c1.
It turns out that commit can cause problems for systems with multiple
GPUs, and causes X to hang on at least a HP Pavilion dv7 with hybrid
graphics.
This got noticed originally in 4.4.4, where this patch had already
gotten back-ported, but 4.5-rc7 was verified to have the same problem.
Alexander Deucher says:
"It looks like you have a muxed system so I suspect what's happening is
that one of the display is being reported as connected for both the
IGP and the dGPU and then the desktop environment gets confused or
there some sort problem in the detect functions since the mux is not
switched to the dGPU. I don't see an easy fix unless Dave has any
ideas. I'd say just revert for now"
Reported-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@kernel.org # wherever dbb17a21c1 got back-ported
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d3e376f52d ]
This is called without dev->struct_mutex held, we need to use the
_unlocked variant.
Never caught in the wild since you'd need an evil userspace which
races a gem_close ioctl call with the in-progress open.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-17-git-send-email-daniel.vetter@ffwll.ch
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit c175cd16df ]
On DELL U3014 if you clear the table before enabling MST it sometimes
hangs the receiver.
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5e93b8208d ]
Previous implementation does not handle case below: boot up one MST branch
to DP connector of ASIC. After boot up, hot plug 2nd MST branch to DP output
of 1st MST, GUID is not created for 2nd MST branch. When downstream port of
2nd MST branch send upstream request, it fails because 2nd MST branch GUID
is not available.
New Implementation: only create GUID for MST branch and save it within Branch.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5e031d9fe8 ]
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 2d02b8bdba ]
During DRAM initialization on certain ASpeed devices, an incorrect
bit (bit 10) was checked in the "SDRAM Bus Width Status" register
to determine DRAM width.
Query bit 6 instead in accordance with the Aspeed AST2050 datasheet v1.05.
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 39d4275058 ]
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bc3f5d8c4c ]
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit f6ff4f67cd ]
An arbitrary amount of time can pass between spin_unlock and
radeon_fence_wait_any, so we need to ensure that nobody frees the
fences from under us.
Based on the analogous fix for amdgpu.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 26f6f2d301 ]
Since sequence block v2 the second byte contains flags other than just
pull up/down. Don't pass arbitrary data to the sideband interface.
The rest may or may not work for sequence block v2, but there should be
no harm done.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ebe3c2eee623afc4b3a134533b01f8d591d13f32.1454582914.git.jani.nikula@intel.com
(cherry picked from commit 4e1c63e376)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit a9ebb3e46c ]
Our PBN value overflows the 20 bits integer part of the 20.12
fixed point. We need to use 31.32 fixed point to avoid this.
This happens with display clocks larger than 293122 (at 24 bpp),
which we see with the Sharp (and similar) 4k tiled displays.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit dabe19540a ]
In drm_dp_mst_allocate_vcpi, it returns true in two paths,
but in one path, there is no reference couting decrease.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit a28bbd5824 ]
Write-combining is a CPU feature. From the GPU POV, these both simply
mean no GPU<->CPU cache coherency.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 5efd407674 ]
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
commit 996a2239f9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 19 11:24:34 2013 +0200
drm/i915: Disable high-bpc on pre-1.4 EDID screens
Cc: stable@vger.kernel.org
Reported-and-tested-by: Dihan Wickremasuriya <nayomal@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105331
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452695720-7076-1-git-send-email-jani.nikula@intel.com
(cherry picked from commit 013dd9e038)
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 7a11a334aa ]
This is needed to receive correct port
number from RAD, so MSTB could be found
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit d87af4d105 ]
Fixed wrong usage of strncat, switched to strlcpy.
While sending the string size to function to reduce
the potential for misuse in future.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 75af4c8c4c ]
This fix is needed to support more then two
branch displays, so RAD address consist at
least of 2 elements
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit bd93432087 ]
In case broadcast message received in UP request,
RAD cannot be used to identify message originator.
Message should be parsed, originator should be found
by GUID from parsed message.
Also reply with broadcast in case broadcast message
received (for now it is always broadcast)
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 42ef344c09 ]
eoffset is sometimes treated as the last address inside the address
range, and sometimes as the first address outside the range. This
was resulting in errors when a test filled up the entire address
space. Make it consistent to always be the last address within the
range. Also fixed related errors when checking the VA limit and in
radeon_vm_fence_pts.
Signed-off-by: Felix.Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 587cdda8f7 ]
This allows us to add the real execution fence as shared.
v2: fix typo
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit dbb17a21c1 ]
Need to call this on resume if displays changes during
suspend in order to properly be notified of changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
[ Upstream commit 8e7a65aa70 ]
We accidentally lost the initial DPLL register write in
1c4e027461 drm/i915: Fix DVO 2x clock enable on 830M
The "three times for luck" hack probably saved us from a total
disaster. But anyway, bring the initial write back so that the
code actually makes some sense.
Reported-and-tested-by: Nick Bowler <nbowler@draconx.ca>
References: http://mid.gmane.org/CAN_QmVyMaArxYgEcVVsGvsMo7-6ohZr8HmF5VhkkL4i9KOmrhw@mail.gmail.com
Cc: stable@vger.kernel.org
Cc: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
