[ Upstream commit 248be83dcb ]
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90186af404 ]
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf2 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ed7d42e24e ]
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2a3771ae8 ]
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5377adb092 upstream.
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da ("usb: Use the USB_SS_MULT() macro to get the ...")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 464ad8c43a upstream.
When a USB 3.0 mass storage device is disconnected in transporting
state, storage device driver may handle it as a transport error and
reset the device by invoking usb_reset_and_verify_device()
and following could happen:
in usb_reset_and_verify_device():
udev->bos = NULL;
For U1/U2 enabled devices, driver will disable LPM, and in some
conditions:
from usb_unlocked_disable_lpm()
--> usb_disable_lpm()
--> usb_enable_lpm()
udev->bos->ss_cap->bU1devExitLat;
And it causes 'NULL pointer' and 'kernel panic':
[ 157.976257] Unable to handle kernel NULL pointer dereference
at virtual address 00000010
...
[ 158.026400] PC is at usb_enable_link_state+0x34/0x2e0
[ 158.031442] LR is at usb_enable_lpm+0x98/0xac
...
[ 158.137368] [<ffffffc0006a1cac>] usb_enable_link_state+0x34/0x2e0
[ 158.143451] [<ffffffc0006a1fec>] usb_enable_lpm+0x94/0xac
[ 158.148840] [<ffffffc0006a20e8>] usb_disable_lpm+0xa8/0xb4
...
[ 158.214954] Kernel panic - not syncing: Fatal exception
This commit moves 'udev->bos = NULL' behind usb_unlocked_disable_lpm()
to prevent from NULL pointer access.
Issue can be reproduced by following setup:
1) A SS pen drive behind a SS hub connected to the host.
2) Transporting data between the pen drive and the host.
3) Abruptly disconnect hub and pen drive from host.
4) With a chance it crashes.
Signed-off-by: Hans Yang <hansy@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 183e53e8dd upstream.
The CPPI-4.1 driver selects TI_CPPI41, which is a dmaengine
driver and that may not be available when CONFIG_DMADEVICES
is not set:
warning: (USB_TI_CPPI41_DMA) selects TI_CPPI41 which has unmet direct dependencies (DMADEVICES && ARCH_OMAP)
This adds an extra dependency to avoid generating warnings in randconfig
builds. Ideally we'd remove the 'select' statement, but that has the
potential to break defconfig files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 411dd19c68 ("usb: musb: Kconfig: Select the DMA driver if DMA mode of MUSB is enabled")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 391e6dcb37 upstream.
pxa27x disconnects pullups on suspend but doesn't
notify the gadget driver about it, so gadget driver
can't disable the endpoints it was using.
This causes problems on resume because gadget core
will think endpoints are still enabled and just
ignore the following usb_ep_enable().
Fix this problem by calling
gadget_driver->disconnect().
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9fa1887dc upstream.
qset_fill_page_list() do not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad87e03213 upstream.
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c90e610b6 upstream.
CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.
Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fa62b1a31 upstream.
The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0e80fbd56 upstream.
The flash loader has been seen on a Telit UE910 modem. The flash loader
is a bit special, it presents both an ACM and CDC Data interface but
only the latter is useful. Unless a magic string is sent to the device
it will disappear and the regular modem device appears instead.
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f33a7f72e5 upstream.
Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.
The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.
"This is what happens when the device is turned on (without modifying
the drivers):
[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:
[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14
Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2f2061994 upstream.
Commit 53147b6cab ("toshiba_acpi: Fix
hotkeys registration on some toshiba models") fixed an issue on some
laptops regarding hotkeys registration, however, if failed to address
the initialization of the hotkey_event_type variable, and thus, it can
lead to potential unwanted effects as the variable is being checked.
This patch initializes such variable to avoid such unwanted effects.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 399235dc6e upstream.
Both for FIFO and CRB interface TCG has decided to use the same HID
MSFT0101. They can be differentiated by looking at the start method from
TPM2 ACPI table. This patches makes necessary fixes to tpm_tis and
tpm_crb modules in order to correctly detect, which module should be
used.
For MSFT0101 we must use struct acpi_driver because struct pnp_driver
has a 7 character limitation.
It turned out that the root cause in b371616b8 was not correct for
https://bugzilla.kernel.org/show_bug.cgi?id=98181.
v2:
* One fixup was missing from v1: is_tpm2_fifo -> is_fifo
v3:
* Use pnp_driver for existing HIDs and acpi_driver only for MSFT0101 in
order ensure backwards compatibility.
v4:
* Check for FIFO before doing *anything* in crb_acpi_add().
* There was return immediately after acpi_bus_unregister_driver() in
cleanup_tis(). This caused pnp_unregister_driver() not to be called.
Reported-by: Michael Saunders <mick.saunders@gmail.com>
Reported-by: Michael Marley <michael@michaelmarley.com>
Reported-by: Jethro Beekman <kernel@jbeekman.nl>
Reported-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Mimi Zohar <zohar@linux.vnet.ibm.com> (on TPM 1.2)
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 100ceb66d5 upstream.
Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers: Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.
However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them. Only their IsoXmitIntMask register is unreliable at early
access.
With my own JMB381 single function controller I found:
- I can reproduce the problem with a lower probability than Craig's.
- If I put a loop around the section which clears and reads
IsoXmitIntMask, then either the first or the second attempt will
return the correct initial mask of 0x0000000f. I never encountered
a case of needing more than a second attempt.
- Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
before the first write, the subsequent read will return the correct
result.
- If I merely ignore a wrong read result and force the known real
result, later isochronous transmit DMA usage works just fine.
So let's just fix this chip bug up by the latter method. Tested with
JMB381 on kernel 3.13 and 4.3.
Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not. I never heard
of this issue together with any other chip though.
I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.
Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.
Reported-by: Clifford Dunn
Reported-by: Craig Moore <craig.moore@qenos.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b16db86f upstream.
Commit 4e752f0ab0 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c25a860d1 ]
Commit fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b1 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68242a5a1e ]
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f088dba3c upstream.
The recently introduced lnet_peer_set_alive() function uses
get_seconds() to read the current time into a shared variable,
but all other uses of that variable compare it to jiffies values.
This changes the current use to jiffies as well for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: af3fa7c71b ("staging/lustre/lnet: peer aliveness status and NI status")
Cc: Liang Zhen <liang.zhen@intel.com>
Cc: James Simmons <uja.ornl@gmail.com>
Cc: Isaac Huang <he.huang@intel.com>
Signed-off-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a596439619 upstream.
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee0c1a65cf upstream.
The correct lock order is atomic_write_lock => termios_rwsem, as
established by tty_write() => n_tty_write().
Fixes: c274f6ef1c ("tty: Hold termios_rwsem for tcflow(TCIxxx)")
Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b2a3d628a upstream.
The data to audit/record is in the 'from' buffer (ie., the input
read buffer).
Fixes: 72586c6061 ("n_tty: Fix auditing support for cannonical mode")
Cc: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 638148e20c upstream.
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e07af133c3 upstream.
Also known as Verizon U620L.
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bcb49e663 upstream.
The Honeywell HGI80 is a wireless interface to the evohome connected
thermostat. It uses a TI 3410 USB-serial port.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 705e63d2b2 upstream.
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 59536da345 upstream.
The DEVICE_HWI type was added under the faulty assumption that Huawei
devices based on Qualcomm chipsets and firmware use the static USB
interface numbering known from Gobi devices. But this model does
not apply to Huawei devices like the HP branded lt4112 (Huawei me906e).
Huawei firmwares will dynamically assign interface numbers. Functions
are renumbered when the firmware is reconfigured.
Fix by changing the DEVICE_HWI type to use a simplified version
of Huawei's subclass + protocol scheme: Blacklisting known network
interface combinations and assuming the rest are serial.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Fixes: e7181d005e ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d5b5ed796 upstream.
It seems like this device has same vendor and product IDs as G2K
devices, but it has different number of interfaces(4 vs 5) and also
different interface layout which makes it currently unusable:
usbcore: registered new interface driver qcserial
usbserial: USB Serial support registered for Qualcomm USB modem
usb 2-1.2: unknown number of interfaces: 5
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[johan: rename define and add comment ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19cd80a214 upstream.
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
[<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
[<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
[<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
[<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
[<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
[<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...
Commit 7f477358e2 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db1319e166 upstream.
Commit d445913ce0 ("usb: ehci-orion: add optional PHY support")
added support for optional phys, but devm_phy_optional_get returns
-ENOSYS if GENERIC_PHY is not enabled.
This causes probe failures, even when there are no phys specified:
[ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38
[ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38
Similar to dwc3, treat -ENOSYS as no phy.
Fixes: d445913ce0 ("usb: ehci-orion: add optional PHY support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae3e57ae26 upstream.
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb7f3d6d32 upstream.
Add platform data and set usb3_lpm_capable and has_lpm_erratum.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 690fb3718a upstream.
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8095a2536 upstream.
This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41adc59cae upstream.
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85da852df6 upstream.
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9e51b2b1f upstream.
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d134c48d88 upstream.
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 9870d895ad ("usb: atmel_usba_udc: Mask status with enabled irqs")
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d115d7050a upstream.
This reverts commit 8f2c9544ab.
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f680f70adb upstream.
The number of spatial streams that are derived from chain mask
for 4x4 devices is using wrong bitmask and conditional check.
This is affecting downlink throughput for QCA99x0 devices. Earlier
cfg_tx_chainmask is not filled by default until user configured it
and so get_nss_from_chainmask never be called. This issue is exposed
by recent commit 166de3f189 ("ath10k: remove supported chain mask").
By default maximum supported chain mask is filled in cfg_tx_chainmask.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cecd9ab80 upstream.
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 562b103a21 upstream.
The sizeof() is invoked on an incorrect variable, likely due to some
copy-paste error, and this might result in memory corruption. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e6e632836 upstream.
This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f9c6e1bc1 upstream.
There were several bugs here.
1) The done label was in the wrong place so we didn't copy any
information out when there was no command given.
2) We were using PAGE_SIZE as the size of the buffer instead of
"PAGE_SIZE - pos".
3) snprintf() returns the number of characters that would have been
printed if there were enough space. If there was not enough space
(and we had fixed the memory corruption bug #2) then it would result
in an information leak when we do simple_read_from_buffer(). I've
changed it to use scnprintf() instead.
I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.
Fixes: 5e6e3a92b9 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
