commit 1fb01ca93a upstream.
Zoltan Boszormenyi reported this regression:
"There's a Realtek RTL8111/8168/8411 (PCI ID 10ec:8168, Subsystem ID
1565:230e) network chip on the mainboard. After the r8169 driver loaded
the IRQs in the machine went berserk. Keyboard keypressed arrived with
considerable latency and duplicated, so no real work was possible.
The machine responded to the power button but didn't actually power
down. It just stuck at the powering down message. I had to press the
power button for 4 seconds to power it down.
The computer is a POS machine with a big battery inside. Because of this,
either ACPI or the Realtek chip kept the bad state and after rebooting,
the network chip didn't even show up in lspci. Not even the PXE ROM
announced itself during boot. I had to disconnect the battery to beat
some sense back to the computer.
The regression happens with 4.0.5, 4.1.0-rc8 and 4.1.0-final. 3.18.16 was
good."
The regression is caused by commit 593669c2ac (x86/PCI/ACPI: Use common
ACPI resource interfaces to simplify implementation). Since commit
593669c2ac, x86 PCI ACPI host bridge driver validates ACPI resources by
first converting an ACPI resource to a 'struct resource' structure and
then applying checks against the converted resource structure. The 'start'
and 'end' fields in 'struct resource' are defined to be type of
resource_size_t, which may be 32 bits or 64 bits depending on
CONFIG_PHYS_ADDR_T_64BIT.
This may cause incorrect resource validation results with 32-bit kernels
because 64-bit ACPI resource descriptors may get truncated when converting
to 32-bit 'start' and 'end' fields in 'struct resource'. It eventually
affects PCI resource allocation subsystem and makes some PCI devices and
the system behave abnormally due to incorrect resource assignment.
So enhance the ACPI resource parsing interfaces to ignore ACPI resource
descriptors with address/offset above 4G when running in 32-bit mode.
With the fix applied, the behavior of the machine was restored to how
3.18.16 worked, i.e. the memory range that is over 4GB is ignored again,
and lspci -vvxxx shows that everything is at the same memory window as
they were with 3.18.16.
Reported-and-tested-by: Boszormenyi Zoltan <zboszor@pr.hu>
Fixes: 593669c2ac (x86/PCI/ACPI: Use common ACPI resource interfaces to simplify implementation)
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c04be18448 upstream.
ACPICA commit 90f5332a15e9d9ba83831ca700b2b9f708274658
This patch adds a new FACS initialization flag for acpi_tb_initialize().
acpi_enable_subsystem() might be invoked several times in OS bootup process,
and we don't want FACS initialization to be invoked twice. Lv Zheng.
Link: 90f5332a
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c04e1fb439 upstream.
ACPICA commit f7b86f35416e3d1f71c3d816ff5075ddd33ed486
The following commit is reported to have broken s2ram on some platforms:
Commit: 0249ed2444
ACPICA: Add option to favor 32-bit FADT addresses.
The platform reports 2 FACS tables (which is not allowed by ACPI
specification) and the new 32-bit address favor rule forces OSPMs to use
the FACS table reported via FADT's X_FIRMWARE_CTRL field.
The root cause of the reported bug might be one of the followings:
1. BIOS may favor the 64-bit firmware waking vector address when the
version of the FACS is greater than 0 and Linux currently only supports
resuming from the real mode, so the 64-bit firmware waking vector has
never been set and might be invalid to BIOS while the commit enables
higher version FACS.
2. BIOS may favor the FACS reported via the "FIRMWARE_CTRL" field in the
FADT while the commit doesn't set the firmware waking vector address of
the FACS reported by "FIRMWARE_CTRL", it only sets the firware waking
vector address of the FACS reported by "X_FIRMWARE_CTRL".
This patch excludes the cases that can trigger the bugs caused by the root
cause 2.
There is no handshaking mechanism can be used by OSPM to tell BIOS which
FACS is currently used. Thus the FACS reported by "FIRMWARE_CTRL" may still
be used by BIOS and the 0 value of the 32-bit firmware waking vector might
trigger such failure.
This patch tries to favor 32bit FACS address in another way where both the
FACS reported by "FIRMWARE_CTRL" and the FACS reported by "X_FIRMWARE_CTRL"
are loaded so that further commit can set firmware waking vector in the
both tables to ensure we can exclude the cases that trigger the bugs caused
by the root cause 2. The exclusion is split into 2 commits as this commit
is also useful for dumping more ACPI tables, it won't get reverted when
such exclusion is no longer necessary. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Link: f7b86f35
Reported-and-tested-by: Oswald Buddenhagen <ossi@kde.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3e13ff3c1 upstream.
Fix a return value (which should be a negative error code) and a
memory leak (the list allocated by acpi_dev_get_resources() needs
to be freed on ioremap() errors too) in acpi_lpss_create_device()
introduced by commit 4483d59e29 'ACPI / LPSS: check the result
of ioremap()'.
Fixes: 4483d59e29 'ACPI / LPSS: check the result of ioremap()'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0294112ee3 upstream.
This effectively reverts the following three commits:
7bc10388cc ACPI / resources: free memory on error in add_region_before()
0f1b414d19 ACPI / PNP: Avoid conflicting resource reservations
b9a5e5e18f ACPI / init: Fix the ordering of acpi_reserve_resources()
(commit b9a5e5e18f introduced regressions some of which, but not
all, were addressed by commit 0f1b414d19 and commit 7bc10388cc
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.
The story is as follows. First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes. Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.
The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e18f).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d19.
That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook. That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d19 wouldn't be
necessary any more.
For this reason, the changes made by commit 0f1b414d19 are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e18f that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e18f "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bc10388cc upstream.
There is a small memory leak on error.
Fixes: 0f1b414d19 (ACPI / PNP: Avoid conflicting resource reservations)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f1b414d19 upstream.
Commit b9a5e5e18f "ACPI / init: Fix the ordering of
acpi_reserve_resources()" overlooked the fact that the memory
and/or I/O regions reserved by acpi_reserve_resources() may
conflict with those reserved by the PNP "system" driver.
If that conflict actually takes place, it causes the reservations
made by the "system" driver to fail while before commit b9a5e5e18f
all reservations made by it and by acpi_reserve_resources() would be
successful. In turn, that allows the resources that haven't been
reserved by the "system" driver to be used by others (e.g. PCI) which
sometimes leads to functional problems (up to and including boot
failures).
To fix that issue, introduce a common resource reservation routine,
acpi_reserve_region(), to be used by both acpi_reserve_resources()
and the "system" driver, that will track all resources reserved by
it and avoid making conflicting requests.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e18f "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d56402d3f upstream.
Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.
Fixes: f25c0ae2b4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b064a8fa77 upstream.
Commit 73f7d1ca32 "ACPI / init: Run acpi_early_init() before
timekeeping_init()" moved the ACPI subsystem initialization,
including the ACPI mode enabling, to an earlier point in the
initialization sequence, to allow the timekeeping subsystem
use ACPI early. Unfortunately, that resulted in boot regressions
on some systems and the early ACPI initialization was moved toward
its original position in the kernel initialization code by commit
c4e1acbb35 "ACPI / init: Invoke early ACPI initialization later".
However, that turns out to be insufficient, as boot is still broken
on the Tyan S8812 mainboard.
To fix that issue, split the ACPI early initialization code into
two pieces so the majority of it still located in acpi_early_init()
and the part switching over the platform into the ACPI mode goes into
a new function, acpi_subsystem_init(), executed at the original early
ACPI initialization spot.
That fixes the Tyan S8812 boot problem, but still allows ACPI
tables to be loaded earlier which is useful to the EFI code in
efi_enter_virtual_mode().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=97141
Fixes: 73f7d1ca32 "ACPI / init: Run acpi_early_init() before timekeeping_init()"
Reported-and-tested-by: Marius Tolzmann <tolzmann@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit b1ef297258 (ACPICA: Permanently set _REV to the value
'2'.) as it causes a sound regression to happen on Dell XPS 13 (2015).
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
Since acpi_reserve_resources() is defined as a device_initcall(),
there's no guarantee that it will be executed in the right order
with respect to the rest of the ACPI initialization code. On some
systems this leads to breakage if, for example, the address range
that should be reserved for the ACPI fixed registers is given to
the PCI host bridge instead if the race is won by the wrong code
path.
Fix this by turning acpi_reserve_resources() into a void function
and calling it directly from within the ACPI initialization sequence.
Reported-and-tested-by: George McCollister <george.mccollister@gmail.com>
Link: http://marc.info/?t=143092384600002&r=1&w=2
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit eec15edbb0 (ACPI / PNP: use device ID list for PNPACPI device
enumeration) changed the way how ACPI devices are enumerated and when
they are added to the PNP bus.
However, it broke the sound card support on (at least) a vintage
IBM ThinkPad 600E: with said commit applied, two of the necessary
"CSC01xx" devices are not added to the PNP bus and hence can not be
found during the initialization of the "snd-cs4236" module. As a
consequence, loading "snd-cs4236" causes null pointer exceptions.
The attached patch fixes the problem end re-enables sound on the
IBM ThinkPad 600E.
Fixes: eec15edbb0 (ACPI / PNP: use device ID list for PNPACPI device enumeration)
Signed-off-by: Witold Szczeponik <Witold.Szczeponik@gmx.net>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7bc5a2bad0 'ACPI: Support _OSI("Darwin") correctly' caused
the MacBook firmware to expose the SBS, resulting in intermittent
hangs of several minutes on boot, and failure to detect or report
the battery. Fix this by adding a 5 us delay to the start of each
SMBUS transaction. This timing is the result of experimentation -
hangs were observed with 3 us but never with 5 us.
Fixes: 7bc5a2bad0 'ACPI: Support _OSI("Darwin") correctly'
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94651
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
An IO port or MMIO resource assigned to a PCI host bridge may be
consumed by the host bridge itself or available to its child
bus/devices. The ACPI specification defines a bit (Producer/Consumer)
to tell whether the resource is consumed by the host bridge itself,
but firmware hasn't used that bit consistently, so we can't rely on it.
Before commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource
interfaces to simplify implementation"), arch/x86/pci/acpi.c ignored
all IO port resources defined by acpi_resource_io and
acpi_resource_fixed_io to filter out IO ports consumed by the host
bridge itself.
Commit 593669c2ac ("x86/PCI/ACPI: Use common ACPI resource interfaces
to simplify implementation") started accepting all IO port and MMIO
resources, which caused a regression that IO port resources consumed
by the host bridge itself became available to its child devices.
Then commit 63f1789ec7 ("x86/PCI/ACPI: Ignore resources consumed by
host bridge itself") ignored resources consumed by the host bridge
itself by checking the IORESOURCE_WINDOW flag, which accidently removed
MMIO resources defined by acpi_resource_memory24, acpi_resource_memory32
and acpi_resource_fixed_memory32.
On x86 and IA64 platforms, all IO port and MMIO resources are assumed
to be available to child bus/devices except one special case:
IO port [0xCF8-0xCFF] is consumed by the host bridge itself
to access PCI configuration space.
So explicitly filter out PCI CFG IO ports[0xCF8-0xCFF]. This solution
will also ease the way to consolidate ACPI PCI host bridge common code
from x86, ia64 and ARM64.
Related ACPI table are archived at:
https://bugzilla.kernel.org/show_bug.cgi?id=94221
Related discussions at:
http://patchwork.ozlabs.org/patch/461633/https://lkml.org/lkml/2015/3/29/304
Fixes: 63f1789ec7 (Ignore resources consumed by host bridge itself)
Reported-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 9faf6136ff (ACPI / SBS: Disable smart battery manager on
Apple) introduced a regression disabling the SBS battery manager.
The battery manager should be marked as present when
acpi_manager_get_info() returns 0.
Fixes: 9faf6136ff (ACPI / SBS: Disable smart battery manager on Apple)
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix a build warning in the intel_pstate driver showing up in non-SMP
builds (Borislav Petkov).
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi).
- Fix a NULL pointer dereference in the ACPI EC driver due to an unsafe
list walk in the query handler removal routine (Chris Bainbridge).
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki).
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki).
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian).
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu).
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0bKD
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"These are fixes mostly (intel_pstate, ACPI core, ACPI EC driver,
cpupower tool), a new CPU ID for the Intel RAPL driver and one
intel_pstate driver improvement that didn't make it to my previous
pull requests due to timing.
Specifics:
- Fix a build warning in the intel_pstate driver showing up in
non-SMP builds (Borislav Petkov)
- Change one of the intel_pstate's P-state selection parameters for
Baytrail and Cherrytrail CPUs to significantly improve performance
at the cost of a small increase in energy consumption (Kristen
Carlson Accardi)
- Fix a NULL pointer dereference in the ACPI EC driver due to an
unsafe list walk in the query handler removal routine (Chris
Bainbridge)
- Get rid of a false-positive lockdep warning in the ACPI container
hot-remove code (Rafael J Wysocki)
- Prevent the ACPI device enumeration code from creating device
objects of a wrong type in some cases (Rafael J Wysocki)
- Add Skylake processors support to the Intel RAPL power capping
driver (Brian Bian)
- Drop the stale MAINTAINERS entry for the ACPI dock driver that is
regarded as part of the ACPI core and maintained along with it now
(Chao Yu)
- Fix cpupower tool breakage caused by a library API change in libpci
3.3.0 (Lucas Stach)"
* tag 'pm+acpi-4.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / scan: Add a scan handler for PRP0001
ACPI / scan: Annotate physical_node_lock in acpi_scan_is_offline()
ACPI / EC: fix NULL pointer dereference in acpi_ec_remove_query_handler()
MAINTAINERS: remove maintainship entry of docking station driver
powercap / RAPL: Add support for Intel Skylake processors
cpufreq: intel_pstate: Fix an annoying !CONFIG_SMP warning
intel_pstate: Change the setpoint for Atom params
cpupower: fix breakage from libpci API change
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
If the special PRP0001 device ID is present in the given device's list
of ACPI/PNP IDs and the device has a valid "compatible" property in
the _DSD, it should be enumerated using the default mechanism,
unless some scan handlers match the IDs preceding PRP0001 in the
device's list of ACPI/PNP IDs. In addition to that, no scan handlers
matching the IDs following PRP0001 in that list should be attached
to the device.
To make that happen, define a scan handler that will match PRP0001
and trigger the default enumeration for the matching devices if the
"compatible" property is present for them.
Since that requires the check for platform_id and device->handler
to be removed from acpi_default_enumeration(), move the fallback
invocation of acpi_default_enumeration() to acpi_bus_attach()
(after it's checked if there's a matching ACPI driver for the
device), which is a better place to call it, and do the platform_id
check in there too (device->handler is guaranteed to be unset at
the point where the function is looking for a matching ACPI driver).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
acpi_scan_is_offline() may be called under the physical_node_lock
lock of the given device object's parent, so prevent lockdep from
complaining about that by annotating that instance with
SINGLE_DEPTH_NESTING.
Fixes: caa73ea158 (ACPI / hotplug / driver core: Handle containers in a special way)
Reported-and-tested-by: Xie XiuQi <xiexiuqi@huawei.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use list_for_each_entry_safe for iterating because handler may be freed
in the loop.
BUG: unable to handle kernel NULL pointer dereference at 000000000000002c
IP: [<ffffffff814d69c8>] acpi_ec_put_query_handler+0x7/0x1a
Call Trace:
acpi_ec_remove_query_handler+0x87/0x97
acpi_smbus_hc_remove+0x2a/0x44 [sbshc]
acpi_device_remove+0x7b/0x9a
__device_release_driver+0x7e/0x110
driver_detach+0xb0/0xc0
bus_remove_driver+0x54/0xe0
driver_unregister+0x2b/0x60
acpi_bus_unregister_driver+0x10/0x12
acpi_smb_hc_driver_exit+0x10/0x12 [sbshc]
SyS_delete_module+0x1b8/0x210
system_call_fastpath+0x12/0x6a
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix for a GPE handling regression on Dell Latitude D600 that
caused GPE signaling to stop working on that machine, which
appears to be due to a hardware glitch, but it used to work
and it can be made work again in a relativly straightforward
way (Rafael J Wysocki).
- Fix for a mutex unlock regression related to the handling of ACPI
tables introduced during the 3.16 development cycle (Octavian Purdila).
- _REV modification to always return 2 which has been done by all
versions of Windows since NT and the firmware people started to
use it to distinguish between OSes in their AML and do some silly
and wrong things on that basis (Bob Moore).
- Fixes and cleanups related to the acpi_physicall_address data type
including one stable-candidate fix for an issue occasionally occuring
on 64-bit machines running 32-bit kernels where using offsets provided
by the firmware may lead to address overflows (Lv Zheng).
- External() opcode support infrastructure needed for recompiling
disassembled ACPI tables in some cases including interpreter
modification to ignore that opcode (Bob Moore).
- Support for the "Windows 2015" string in _OSI (Bob Moore).
- GPE debug interface change to return values read from hardware
registers (Lv Zheng).
- Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).
- Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
Bob Moore).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xUhi
-----END PGP SIGNATURE-----
Merge tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"This updates the kernel's ACPICA code to upstream revision 20150410
and adds a fix for a GPE handling regression introduced during the
3.19 cycle on top of that.
Included are two stable-candidate bug fixes (one of them fixing a 3.16
regression), multiple other fixes and a bunch of cleanups.
Specifics:
- Fix for a GPE handling regression on Dell Latitude D600 that caused
GPE signaling to stop working on that machine, which appears to be
due to a hardware glitch, but it used to work and it can be made
work again in a relativly straightforward way (Rafael J Wysocki).
- Fix for a mutex unlock regression related to the handling of ACPI
tables introduced during the 3.16 development cycle (Octavian
Purdila).
- _REV modification to always return 2 which has been done by all
versions of Windows since NT and the firmware people started to use
it to distinguish between OSes in their AML and do some silly and
wrong things on that basis (Bob Moore).
- Fixes and cleanups related to the acpi_physicall_address data type
including one stable-candidate fix for an issue occasionally
occuring on 64-bit machines running 32-bit kernels where using
offsets provided by the firmware may lead to address overflows (Lv
Zheng).
- External() opcode support infrastructure needed for recompiling
disassembled ACPI tables in some cases including interpreter
modification to ignore that opcode (Bob Moore).
- Support for the "Windows 2015" string in _OSI (Bob Moore).
- GPE debug interface change to return values read from hardware
registers (Lv Zheng).
- Removal of the __DATE__ macro usage in tools (Rasmus Villemoes).
- Assorted minor fixes and cleanups (Lv Zheng, Rickard Strandqvist,
Bob Moore)"
* tag 'acpica-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Store GPE register enable masks upfront
ACPICA: Update version to 20150410.
ACPICA: Fix a couple issues with the local printf module.
ACPICA: Disassembler: Some cleanup of the table dump module.
ACPICA: iASL: Add support for MSDM ACPI table.
ACPICA: Update for SLIC ACPI table.
ACPICA: Add "//" before ascii output of buffers.
ACPICA: Remove unused internal AML opcode.
ACPICA: Permanently set _REV to the value '2'.
ACPICA: Add "Windows 2015" string to _OSI support.
ACPICA: Add infrastructure for External() opcode.
ACPICA: iASL: Enhancement for constant folding.
ACPICA: iASL/Disassembler: Add option to assume table contains valid AML.
ACPICA: Update AML Debugger global variables.
ACPICA: Update Resource descriptor dump module.
ACPICA: Fix a sscanf format string.
ACPICA: Casting changes around acpi_physical_address/acpi_size.
ACPICA: Resources: Correct conditional compilation definitions.
ACPICA: Utilities: Correct conditional compilation definitions.
ACPICA: Tables: Move an iasl specific table function to iasl source file.
...
- Generic PM domains support update including new PM domain
callbacks to handle device initialization better (Russell King,
Rafael J Wysocki, Kevin Hilman).
- Unified device properties API update including a new mechanism
for accessing data provided by platform initialization code
(Rafael J Wysocki, Adrian Hunter).
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano).
- intel_idle update including support for the Silvermont Core in
the Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause).
- New cpufreq driver for Hisilicon ACPU (Leo Yan).
- intel_pstate update including support for the Knights Landing
chip (Dasaratharaman Chandramouli, Kristen Carlson Accardi).
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann).
- powernv cpufreq driver update (Shilpasri G Bhat).
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi).
- powercap RAPL (Running-Average Power Limit) driver update
including support for Intel Broadwell server chips (Jacob Pan,
Mathias Krause).
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki).
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng).
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems
and a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede).
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu).
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki).
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu).
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu).
- Configurable delay for the system suspend/resume testing facility
(Brian Norris).
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=erd3
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups all over, although there are a few
items that sort of fall into the new feature category.
First off, we have new callbacks for PM domains that should help us to
handle some issues related to device initialization in a better way.
There also is some consolidation in the unified device properties API
area allowing us to use that inferface for accessing data coming from
platform initialization code in addition to firmware-provided data.
We have some new device/CPU IDs in a few drivers, support for new
chips and a new cpufreq driver too.
Specifics:
- Generic PM domains support update including new PM domain callbacks
to handle device initialization better (Russell King, Rafael J
Wysocki, Kevin Hilman)
- Unified device properties API update including a new mechanism for
accessing data provided by platform initialization code (Rafael J
Wysocki, Adrian Hunter)
- ARM cpuidle update including ARM32/ARM64 handling consolidation
(Daniel Lezcano)
- intel_idle update including support for the Silvermont Core in the
Baytrail SOC and for the Airmont Core in the Cherrytrail and
Braswell SOCs (Len Brown, Mathias Krause)
- New cpufreq driver for Hisilicon ACPU (Leo Yan)
- intel_pstate update including support for the Knights Landing chip
(Dasaratharaman Chandramouli, Kristen Carlson Accardi)
- QorIQ cpufreq driver update (Tang Yuantian, Arnd Bergmann)
- powernv cpufreq driver update (Shilpasri G Bhat)
- devfreq update including Tegra support changes (Tomeu Vizoso,
MyungJoo Ham, Chanwoo Choi)
- powercap RAPL (Running-Average Power Limit) driver update including
support for Intel Broadwell server chips (Jacob Pan, Mathias Krause)
- ACPI device enumeration update related to the handling of the
special PRP0001 device ID allowing DT-style 'compatible' property
to be used for ACPI device identification (Rafael J Wysocki)
- ACPI EC driver update including limited _DEP support (Lan Tianyu,
Lv Zheng)
- ACPI backlight driver update including a new mechanism to allow
native backlight handling to be forced on non-Windows 8 systems and
a new quirk for Lenovo Ideapad Z570 (Aaron Lu, Hans de Goede)
- New Windows Vista compatibility quirk for Sony VGN-SR19XN (Chen Yu)
- Assorted ACPI fixes and cleanups (Aaron Lu, Martin Kepplinger,
Masanari Iida, Mika Westerberg, Nan Li, Rafael J Wysocki)
- Fixes related to suspend-to-idle for the iTCO watchdog driver and
the ACPI core system suspend/resume code (Rafael J Wysocki, Chen Yu)
- PM tracing support for the suspend phase of system suspend/resume
transitions (Zhonghui Fu)
- Configurable delay for the system suspend/resume testing facility
(Brian Norris)
- PNP subsystem cleanups (Peter Huewe, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
ACPI / scan: Fix NULL pointer dereference in acpi_companion_match()
ACPI / scan: Rework modalias creation when "compatible" is present
intel_idle: mark cpu id array as __initconst
powercap / RAPL: mark rapl_ids array as __initconst
powercap / RAPL: add ID for Broadwell server
intel_pstate: Knights Landing support
intel_pstate: remove MSR test
cpufreq: fix qoriq uniprocessor build
ACPI / scan: Take the PRP0001 position in the list of IDs into account
ACPI / scan: Simplify acpi_match_device()
ACPI / scan: Generalize of_compatible matching
device property: Introduce firmware node type for platform data
device property: Make it possible to use secondary firmware nodes
PM / watchdog: iTCO: stop watchdog during system suspend
cpufreq: hisilicon: add acpu driver
ACPI / EC: Call acpi_walk_dep_device_list() after installing EC opregion handler
cpufreq: powernv: Report cpu frequency throttling
intel_idle: Add support for the Airmont Core in the Cherrytrail and Braswell SOCs
intel_idle: Update support for Silvermont Core in Baytrail SOC
PM / devfreq: tegra: Register governor on module init
...
It is reported that ACPI interrupts do not work any more on
Dell Latitude D600 after commit c50f13c672 (ACPICA: Save
current masks of enabled GPEs after enable register writes).
The problem turns out to be related to the fact that the
enable_mask and enable_for_run GPE bit masks are not in
sync (in the absence of any system suspend/resume events)
for at least one GPE register on that machine.
Address this problem by writing the enable_for_run mask into
enable_mask as soon as enable_for_run is updated instead of
doing that only after the subsequent register write has
succeeded. For consistency, update acpi_hw_gpe_enable_write()
to store the bit mask to be written into the GPE register
in enable_mask unconditionally before the write.
Since the ACPI_GPE_SAVE_MASK flag is not necessary any more after
that, drop it along with the symbols depending on it.
Reported-and-tested-by: Jim Bos <jim876@xs4all.nl>
Fixes: c50f13c672 (ACPICA: Save current masks of enabled GPEs after enable register writes)
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6853da4c0a99b49d62d6c58d22956cd6ff5759a9
The following commit has fixed local printf issue in width.prec:
Commit: 3589b8b8af
Subject: ACPICA: Utilities: Fix local printf issue.
But this commit only resets width/precision/quialifier to fix the reported
issue and doesn't fix other states issues. So now we still can see breakage
in format types and integer bases.
This patch resets format type/base states for local printf to fix this
issue. Lv Zheng.
Linux kernel is not affected by this patch as acpi_ut_vsnprintf() hasn't
been enabled in the kernel.
Link: 6853da4c
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 657dc227672709895df3192fa5ea59a649b9a76f
Updates the dump buffer utility to comment out the ASCII part
of buffer dump. Prevents some tools from getting confused.
Link: 657dc227
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3ec867764b079a98d8097d705c9f7b68270c04ec
This patch removes unused AML_INT_STATICSTRING_OP. Lv Zheng.
Link: 3ec86776
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7af00219681ab35ebe57d64a9189fd04a5a026d8
Windows uses a value of 2, and has no plans to ever change this. So, _REV is
essentially useless for its primary purpose.
Worse, some BIOS vendors have used the difference in _REV values between
Windows and ACPICA to indicate which one is running.
It has been decided by the ACPI community to deprecate this method, and return
1 for ACPI 1.0 (32-bit integers) and 2 for ACPI 2.0 and greater (both 32-bit
and 64-bit integers.
ACPICA is changed to reflect this.
Link: 7af00219
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b293f602a67da478ae0bec129e68bd99787d9908
This change adds this string for Windows 10.
Link: b293f602
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit d115fe2ffdab449d6107d58580c5afd0a81d65fe
This change adds the basic low-level infrastructure for the External
AML opcode. The interpreter will simply ignore this op, as the op
is intended for use by the disassembler only.
Note that External() opcode is useful for disassembler, interpreter
can simply ignore it and still return exceptions for unknown control
methods so the kernel part only includes the grammar definition of
External() opcode in order to ignore it but doesn't interpret it.
Link: d115fe2f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 4f9e950d41cd6f6c704d5d6cf518647620d65e99
Add support to fold expressions with a target operand -- these are
folded and converted to a Store operator:
Add (4, 3, INT1) --> Store (7, INT1)
Also supports ASL+ constructs:
INT1 = 4 + 3 --> Store (7, INT1)
Linux kernel is not affected by this patch.
Link: 4f9e950d
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f5d2ff3fa05341d9fe27250fcb2e14c7f871432c
For dynamically loaded tables that have unknown ACPI signatures,
this option (-df) forces the disassembler to treat the table as if
it contains valid AML code (like a DSDT or SSDT). Otherwise, the
disassembler will treat the table as an unkown data table and
simply do a hex dump of the table.
Linux kernel is not affected by this patch.
Link: f5d2ff3f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f65d0e5b880860a6da0c336b7c48139d1469f5b4
- Remove unused variables
- Update to use standard naming/capitalization convention.
Linux kernel is not affected by this patch.
Link: f65d0e5b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 184f3cc4d162a6b6b2005eacd8be2fe55f19a245
- Change global #ifdef to check for ACPI_DEBUGGER only.
- Cleanup some long lines and misaligned code.
Link: 184f3cc4
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 46dc081e570b1363af1e368980201cbb65c4100f
Update for some recent changes, detected by MSVC and FreeBSD builds.
Link: 46dc081e
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f92a08512b0b35dce4a7fc6a73216674a3c2541b
Some conditional compilation definitions are wrong across header and source
files. This patch corrects them for the resources component.
NOTE that a further patch in this patchset cleans up all ACPI_EXEC_APP,
converting them into ACPI_DEBUGGER, including part of this change.
Link: f92a0851
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9a5982afbebc56289c4834b5f6dac87e0f04af14
Some conditional compilation definitions are wrong across header and source
files. This patch corrects them for the utilities component.
Link: 9a5982af
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6eb364d790dd103bd4990f808e0095a421c437cb
acpi_tb_store_table() implements a logic that is only correct to iasl. So it
won't be used by any other utilities except iasl. This function is
complained by the kernel users as an unused function. The best choice to
stop releasing it to the Linux kernel should be moving it to adisasm.c.
ACPI table manager can use both struct acpi_table_desc (direct referencing)
and table index (indirect referencing) as the descriptor to the table, so
acpi_tb_get_next_root_index() is extended to return both of them to allow
maximum usability from the callers. NOTE that indirect referencing is a
design result to meet the boot stage static allocation requirement for the
table descriptors.
This is a linuxized acpi_tb_store_table() removing result, there should be
no functional changes introduced to the Linux kernel by this patch except
the additonal kernel unused argument for acpi_tb_get_next_root_index()
(renamed to acpi_tb_get_next_root_index()). This argument is used in the
ACPICA upstream.
Link: 6eb364d7
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 2a9ebd974aee41391f4b0edcd4f0cc5ee23ec2f8
Remove the function acpi_ut_create_pkg_state_and_push() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Link: 2a9ebd97
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3d9fb6d1f216a78ad098d3ad23f1304376c2f4ef
The macro __DATE__ and friends is not allowed in the Linux kernel. Also,
including the build time in output doesn't seem to provide any value.
Link: 3d9fb6d1
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit e25d791e4b3d5b9f4ead298269610cb05f89749a
There is a facility in Linux, developers can obtain GPE and fixed event
status via /sys/firmware/interrupts/. This is implemented using
acpi_get_event_status() and acpi_get_gpe_status(). Recently while debugging some
GPE race issues, it is found that the facility is lacking in the ability to
obtain real hardware register values, the confusing information makes
debugging difficult.
This patch modifies acpi_get_gpe_status() to return EN register values to fix
this gap. Then flags returned from acpi_get_event_status() and
acpi_get_gpe_status() are also cleaned up to reflect this change.
The old ACPI_EVENT_FLAG_SET is carefully kept to avoid regressions. It can
be deleted after we can make sure all its references are removed from OSPM
code. Lv Zheng.
Link: e25d791e
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c70434d4da13e65b6163c79a5aa16b40193631c7
ACPI_MTX_TABLES is acquired and released by the callers of
acpi_tb_install_standard_table() so releasing it in the function itself is
causing the following error in Linux kernel if the table is reloaded:
ACPI Error: Mutex [0x2] is not acquired, cannot release (20141107/utmutex-321)
Call Trace:
[<ffffffff81b0bd48>] dump_stack+0x4f/0x7b
[<ffffffff81546bf5>] acpi_ut_release_mutex+0x47/0x67
[<ffffffff81544357>] acpi_load_table+0x73/0xcb
Link: c70434d4
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Cc: 3.16+ <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b60612373a4ef63b64a57c124576d7ddb6d8efb6
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use 0x%8.8X%8.8X instead of ACPI_PRINTF_UINT
and ACPI_FORMAT_UINT64() instead of
ACPI_FORMAT_NATIVE_UINT()/ACPI_FORMAT_TO_UINT().
This patch also removes above replaced macros as there are no users.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: b6061237
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7f06739db43a85083a70371c14141008f20b2198
For physical addresses, since the address may exceed 32-bit address range
after calculation, we should use %8.8X%8.8X (see ACPI_FORMAT_UINT64()) to
convert the %p formats.
This is a preparation to switch acpi_physical_address to 64-bit on 32-bit
kernel builds.
Link: 7f06739d
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 154f6d074dd38d6ebc0467ad454454e6c5c9ecdf
There are code pieces converting pointers using "(acpi_physical_address) x"
or "ACPI_CAST_PTR (t, x)" formats, this patch cleans up them.
Known issues:
1. Cleanup of "(ACPI_PHYSICAL_ADDRRESS) x" for a table field
For the conversions around the table fields, it is better to fix it with
alignment also fixed. So this patch doesn't modify such code. There
should be no functional problem by leaving them unchanged.
Link: 154f6d07
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c327986430b7eb170c17d0f45735fe71bb62a810
The conversion converts an acpi_physical_address to acpi_physical_address,
this patch thus removes such useless conversion.
Link: c3279864
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7d9fd64397d7c38899d3dc497525f6e6b044e0e3
OSPMs like Linux expect an acpi_physical_address returning value from
acpi_find_root_pointer(). This triggers warnings if sizeof (acpi_size) doesn't
equal to sizeof (acpi_physical_address):
drivers/acpi/osl.c:275:3: warning: passing argument 1 of 'acpi_find_root_pointer' from incompatible pointer type [enabled by default]
In file included from include/acpi/acpi.h:64:0,
from include/linux/acpi.h:36,
from drivers/acpi/osl.c:41:
include/acpi/acpixf.h:433:1: note: expected 'acpi_size *' but argument is of type 'acpi_physical_address *'
This patch corrects acpi_find_root_pointer().
Link: 7d9fd643
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
