commit 2eecb2e04a upstream.
There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.
[gregory.clement@free-electrons.com: add fixes tag]
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca5902a654 upstream.
When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and fixes tag]
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4423c18e46 upstream.
When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.
[gregory.clement@free-electrons.com: add fixes tag]
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19deaa217b upstream.
The alignment checks at pfn driver startup fail to properly account for
the 'start_pad' in the case where the namespace is misaligned relative
to its internal alignment. This is typically triggered in 1G aligned
namespace, but could theoretically trigger with small namespace
alignments. When this triggers the kernel reports messages of the form:
dax2.1: bad offset: 0x3c000000 dax disabled align: 0x40000000
Fixes: 1ee6667cd8 ("libnvdimm, pfn, dax: fix initialization vs autodetect...")
Reported-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24e3a7fb60 upstream.
Due to a spec misinterpretation, the Linux implementation of the BTT log
area had different padding scheme from other implementations, such as
UEFI and NVML.
This fixes the padding scheme, and defaults to it for new BTT layouts.
We attempt to detect the padding scheme in use when probing for an
existing BTT. If we detect the older/incompatible scheme, we continue
using it.
Reported-by: Juston Li <juston.li@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Fixes: 5212e11fde ("nd_btt: atomic sector updates")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41fce90f26 upstream.
The following namespace configuration attempt:
# ndctl create-namespace -e namespace0.0 -m devdax -a 1G -f
libndctl: ndctl_dax_enable: dax0.1: failed to enable
Error: namespace0.0: failed to enable
failed to reconfigure namespace: No such device or address
...fails when the backing memory range is not physically aligned to 1G:
# cat /proc/iomem | grep Persistent
210000000-30fffffff : Persistent Memory (legacy)
In the above example the 4G persistent memory range starts and ends on a
256MB boundary.
We handle this case correctly when needing to handle cases that violate
section alignment (128MB) collisions against "System RAM", and we simply
need to extend that padding/truncation for the 1GB alignment use case.
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute...")
Reported-and-tested-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92411f6d7f upstream.
The commit 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap
initialization sequence") moved a bunch of logic around, but forgot to
update the gotos after the introduction of the err_free_dotclock label.
It means that if we fail later that the one introduced in that commit,
we'll just to the old label which isn't free the clock we created. This
will result in a breakage as soon as someone tries to do something with
that clock, since its resources will have been long reclaimed.
Fixes: 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap initialization sequence")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f83c1cebc731f0b4251f5ddd7b38c718cd79bb0b.1512662253.git-series.maxime.ripard@free-electrons.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2797c4a11f upstream.
From the shrinker paths, we want to relinquish the GPU and GGTT access to
the object, releasing the backing storage back to the system for
swapout. As a part of that process we would unpin the pages, marking
them for access by the CPU (for the swapout/swapin). However, if that
process was interrupted after unbind the vma, we missed a flush of the
inflight GGTT writes before we made that GTT space available again for
reuse, with the prospect that we would redirect them to another page.
The bug dates back to the introduction of multiple GGTT vma, but the
code itself dates to commit 02bef8f98d ("drm/i915: Unbind closed vma
for i915_gem_object_unbind()").
Fixes: 02bef8f98d ("drm/i915: Unbind closed vma for i915_gem_object_unbind()")
Fixes: c5ad54cf7d ("drm/i915: Use partial view in mmap fault handler")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204132513.7303-1-chris@chris-wilson.co.uk
(cherry picked from commit 5888fc9eac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61d2f2a057 upstream.
Our MMC host driver now issues a reset, instead of just deasserting
the reset control, since commit c34eda69ad ("mmc: sunxi: Reset the
device at probe time"). The sun9i-mmc clock driver does not support
this, and will fail, which results in MMC not probing.
This patch implements the reset callback by asserting the reset control,
then deasserting it after a small delay.
Fixes: 7a6fca879f ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171218035751.20661-1-wens@csie.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2b3c35359 upstream.
Guenter Roeck reported an interrupt storm on a prototype system which is
based on Cyan Chromebook. The root cause turned out to be a incorrectly
configured pin that triggers spurious interrupts. This will be fixed in
coreboot but currently we need to prevent the interrupt storm from
happening by masking all interrupts (but not GPEs) on those systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Fixes: bcb48cca23 ("pinctrl: cherryview: Do not mask all interrupts in probe")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 251c201bf4 upstream.
The Armada 3700 SPI controller has 2 ranges of prescaler coefficients.
One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by
steps of 2.
This commit fixes the prescaler coefficients that are over 15 so that it
uses the correct range of values. The prescaling coefficient is rounded
to the upper value if it is odd.
This was tested on Espressobin with spidev and a locigal analyser.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a1314fa69 upstream.
When the core is configured in C_SPI_MODE > 0, it integrates a
lookup table that automatically configures the core in dual or quad mode
based on the command (first byte on the tx fifo).
Unfortunately, that list mode_?_memoy_*.mif does not contain all the
supported commands by the flash.
Since 4.14 spi-nor automatically tries to probe the flash using SFDP
(command 0x5a), and that command is not part of the list_mode table.
Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads
into a stall that can only be recovered with a soft rest.
This patch detects this kind of stall and returns -EIO to the caller on
those commands. spi-nor can handle this error properly:
m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404
m25p80 spi0.0: SPI transfer failed: -5
spi_master spi0: failed to transfer one message from queue
m25p80 spi0.0: s25sl064p (8192 Kbytes)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf3f1752a upstream.
Diva GSP card has built-in serial AUX port and ATI graphic card which simply
don't work and which both don't have external connectors. User Guides even
mention that those devices shouldn't be used.
So, prevent that Linux drivers try to enable those devices.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5839ee7389 upstream.
It is incorrect to call pci_restore_state() for devices in low-power
states (D1-D3), as that involves the restoration of MSI setup which
requires MMIO to be operational and that is only the case in D0.
However, pci_pm_thaw_noirq() may do that if the driver's "freeze"
callbacks put the device into a low-power state, so fix it by making
it force devices into D0 via pci_set_power_state() instead of trying
to "update" their power state which is pointless.
Fixes: e60514bd44 (PCI/PM: Restore the status of PCI devices across hibernation)
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Maarten Lankhorst <dev@mblankhorst.nl>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Maarten Lankhorst <dev@mblankhorst.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e9b13cbb upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Note that the CONFIG_OF compile guard can be removed as
of_get_child_by_name() provides a !CONFIG_OF implementation which always
fails.
Fixes: 37e13cecaa ("mfd: Add support for Device Tree to twl6040")
Fixes: ca2cad6ae3 ("mfd: Fix twl6040 build failure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a423772de upstream.
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while leaking any matching node.
To make things worse, any matching node would not even necessarily be a
child node as the whole device tree was searched depth-first starting at
the parent.
Fixes: 019a7e6b7b ("mfd: twl4030-audio: Add DT support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15d8374874 upstream.
On the Tegra124 Nyan-Big chromebook the very first SPI message sent to
the EC is failing.
The Tegra SPI driver configures the SPI chip-selects to be active-high
by default (and always has for many years). The EC SPI requires an
active-low chip-select and so the Tegra chip-select is reconfigured to
be active-low when the EC SPI driver calls spi_setup(). The problem is
that if the first SPI message to the EC is sent too soon after
reconfiguring the SPI chip-select, it fails.
The EC SPI driver prevents back-to-back SPI messages being sent too
soon by keeping track of the time the last transfer was sent via the
variable 'last_transfer_ns'. To prevent the very first transfer being
sent too soon, initialise the 'last_transfer_ns' variable after calling
spi_setup() and before sending the first SPI message.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adf6895754 upstream.
Integration testing with a BIOS that generates injected health event
notifications fails to communicate those events to userspace. The nfit
driver neglects to link the ACPI DIMM device with the necessary driver
data so acpi_nvdimm_notify() fails this lookup:
nfit_mem = dev_get_drvdata(dev);
if (nfit_mem && nfit_mem->flags_attr)
sysfs_notify_dirent(nfit_mem->flags_attr);
Add the necessary linkage when installing the notification handler and
clean it up when the nfit driver instance is torn down.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: ba9c8dd3c2 ("acpi, nfit: add dimm device notification support")
Reported-by: Daniel Osawa <daniel.k.osawa@intel.com>
Tested-by: Daniel Osawa <daniel.k.osawa@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb82e0b4a7 upstream.
The commit f6f8285132 ("pstore: pass allocated memory region back to
caller") changed the check of the return value from erst_read() in
erst_reader() in the following way:
if (len == -ENOENT)
goto skip;
- else if (len < 0) {
- rc = -1;
+ else if (len < sizeof(*rcd)) {
+ rc = -EIO;
goto out;
This introduced another bug: since the comparison with sizeof() is
cast to unsigned, a negative len value doesn't hit any longer.
As a result, when an error is returned from erst_read(), the code
falls through, and it may eventually lead to some weird thing like
memory corruption.
This patch adds the negative error value check more explicitly for
addressing the issue.
Fixes: f6f8285132 (pstore: pass allocated memory region back to caller)
Tested-by: Jerry Tang <jtang@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bff5bf9db1 upstream.
Sending the switch state change twice within the same frame is invalid
evdev protocol and only works if the client handles keys immediately as
well. Processing events immediately is incorrect, it forces a fake
order of events that does not exist on the device.
Recent versions of libinput changed to only process the device state and
SYN_REPORT time, so now the key event is lost.
https://bugs.freedesktop.org/show_bug.cgi?id=104041
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2b033260 upstream.
The DT specifies a threshold of 65000, we setup the register with a value in
the temperature resolution for the controller, 64656.
When we reach 64656, the interrupt fires, the interrupt is disabled. Then the
irq thread runs and calls thermal_zone_device_update() which will call in turn
hisi_thermal_get_temp().
The function will look if the temperature decreased, assuming it was more than
65000, but that is not the case because the current temperature is 64656
(because of the rounding when setting the threshold). This condition being
true, we re-enable the interrupt which fires immediately after exiting the irq
thread. That happens again and again until the temperature goes to more than
65000.
Potentially, there is here an interrupt storm if the temperature stabilizes at
this temperature. A very unlikely case but possible.
In any case, it does not make sense to handle dozens of alarm interrupt for
nothing.
Fix this by rounding the threshold value to the controller resolution so the
check against the threshold is consistent with the one set in the controller.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48880b979c upstream.
The step and the base temperature are fixed values, we can simplify the
computation by converting the base temperature to milli celsius and use a
pre-computed step value. That saves us a lot of mult + div for nothing at
runtime.
Take also the opportunity to change the function names to be consistent with
the rest of the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cb4de785c upstream.
The threaded interrupt for the alarm interrupt is requested before the
temperature controller is setup. This one can fire an interrupt immediately
leading to a kernel panic as the sensor data is not initialized.
In order to prevent that, move the threaded irq after the Tsensor is setup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c176b10b02 upstream.
The interrupt for the temperature threshold is not enabled at the end of the
probe function, enable it after the setup is complete.
On the other side, the irq_enabled is not correctly set as we are checking if
the interrupt is masked where 'yes' means irq_enabled=false.
irq_get_irqchip_state(data->irq, IRQCHIP_STATE_MASKED,
&data->irq_enabled);
As we are always enabling the interrupt, it is pointless to check if
the interrupt is masked or not, just set irq_enabled to 'true'.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b77eb45e0d ]
Do not include EM specified MAC address in total MACs of the
UC MAC list.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4bbdfe2560 ]
Clear the MAC table digest when the MAC table is freed.
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Scott Franco <safranco@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af2eca5320 ]
The incoming mode might have a missing vrefresh field if it came from
drmModeSetCrtc(), which the kernel is supposed to calculate using
drm_mode_vrefresh(). We could either use that or the adjusted_mode's
original vrefresh value.
However, we can maintain a more exact vrefresh value (not just the
integer approximation), by scaling by the ratio of our clocks.
v2: Use math suggested by Andrzej Hajda instead.
v3: Simplify math now that adjusted_mode->clock isn't padded.
v4: Drop some parens.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f187851b9b ]
When failing to enter broadcast timer mode for an idle state that
requires it, a new state is selected that does not require broadcast,
but the broadcast variable remains set. This causes
tick_broadcast_exit to be called despite not having entered broadcast
mode.
This causes the WARN_ON_ONCE(!irqs_disabled()) to trigger in some
cases. It does not appear to cause problems for code today, but seems
to violate the interface so should be fixed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74717b28cb ]
If there is any non expired timer in the queue, the RTC alarm is never set.
This is an issue when adding a timer that expires before the next non
expired timer.
Ensure the RTC alarm is set in that case.
Fixes: 2b2f5ff00f ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3ed79188 ]
The HDMI DDC clock found in the CCU is the parent of the actual DDC
clock within the HDMI controller. That clock is also named "hdmi-ddc".
Rename the one in the CCU to "ddc". This makes more sense than renaming
the one in the HDMI controller to something else.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e437b1d7e ]
After the loop in hns_roce_v1_mr_free_work_fn function, it is possible that
all qps will have been freed (in which case ne will be 0). If that
happens, then later in the function when we dereference hr_qp we will
get an exception. Check ne is not 0 to make sure we actually have an
hr_qp left to work on.
This patch fixes the smatch error as below:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:1009 hns_roce_v1_mr_free_work_fn()
error: we previously assumed 'hr_qp' could be null
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e876a8a7e9 ]
State is initially reported as UNKNOWN. Before register call
netif_carrier_off(). Once the device is opened, call netif_carrier_on() in
order to set the state to UP.
Signed-off-by: Mick Tarsel <mjtarsel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17a9180994 ]
When we process VF mailboxes, the driver is likely going to also queue
up messages to the switch manager. This process merely queues up the
FIFO, but doesn't actually begin the transmission process. Because we
hold the mailbox lock during this VF processing, the PF<->SM mailbox is
not getting processed at this time. Ensure that we actually process the
PF<->SM mailbox in between each PF<->VF mailbox.
This should ensure prompt transmission of the messages queued up after
each VF message is received and handled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 523184972b ]
With virtual PCI-Express chipsets, we now see userspace/guest drivers
trying to match the physical MPS setting to a virtual downstream port.
Of course a lone physical device surrounded by virtual interconnects
cannot make a correct decision for a proper MPS setting. Instead,
let's virtualize the MPS control register so that writes through to
hardware are disallowed. Userspace drivers like QEMU assume they can
write anything to the device and we'll filter out anything dangerous.
Since mismatched MPS can lead to AER and other faults, let's add it
to the kernel side rather than relying on userspace virtualization to
handle it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c53d11f669 ]
Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources. The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.
When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state. During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set. This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2299e4323d ]
Warning messages when NVME_TARGET_FC not defined on ppc builds
The lpfc_nvmet_replenish_context() function is only meaningful when NVME
target mode enabled. Surround the function body with ifdefs for target
mode enablement.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e8bcf0ae4c ]
Local Reject/Invalid RPI errors seen during discovery.
Temporary RPI cleanup was occurring regardless of SLI rev. It's only
necessary on SLI-4.
Adjust the test for whether cleanup is necessary.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 184fc2b9a8 ]
Firmware update fails with: status x17 add_status x56 on the final write
If multiple DMA buffers are used for the download, some firmware revs
have difficulty with signatures and crcs split across the dma buffer
boundaries. Resolve by making all writes be a single 4k page in length.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e256ac5b1 ]
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86acc79071 ]
Previously, if an non-fatal error was reported by an endpoint, we
called report_error_detected() for the endpoint, every sibling on the
bus, and their descendents. If any of them did not implement the
.error_detected() method, do_recovery() failed, leaving all these
devices unrecovered.
For example, the system described in the bugzilla below has two devices:
0000:74:02.0 [19e5:a230] SAS controller, driver has .error_detected()
0000:74:03.0 [19e5:a235] SATA controller, driver lacks .error_detected()
When a device such as 74:02.0 reported a non-fatal error, do_recovery()
failed because 74:03.0 lacked an .error_detected() method. But per PCIe
r3.1, sec 6.2.2.2.2, such an error does not compromise the Link and
does not affect 74:03.0:
Non-fatal errors are uncorrectable errors which cause a particular
transaction to be unreliable but the Link is otherwise fully functional.
Isolating Non-fatal from Fatal errors provides Requester/Receiver logic
in a device or system management software the opportunity to recover from
the error without resetting the components on the Link and disturbing
other transactions in progress. Devices not associated with the
transaction in error are not impacted by the error.
Report non-fatal errors only to the endpoint that reported them. We really
want to check for AER_NONFATAL here, but the current code structure doesn't
allow that. Looking for pci_channel_io_normal is the best we can do now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197055
Fixes: 6c2b374d74 ("PCI-Express AER implemetation: AER core and aerdriver")
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be664cbefc ]
Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.
This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.
Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.
Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 227630cccd ]
This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:
1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.
This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.
2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.
This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52ca7d0f7b ]
The PCA9552 lines can be used either for driving LEDs or as GPIOs. The
manual states that for LEDs, the operation is open-drain:
The LSn LED select registers determine the source of the LED data.
00 = output is set LOW (LED on)
01 = output is set high-impedance (LED off; default)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
For GPIOs it suggests a pull-up so that the open-case drives the line
high:
For use as output, connect external pull-up resistor to the pin
and size it according to the DC recommended operating
characteristics. LED output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is
programmed LOW through the ‘LED selector’ register. The output
can be pulse-width controlled when PWM0 or PWM1 are used.
Now, I have a hardware design that uses the LED controller to control
LEDs. However, for $reasons, we're using the leds-gpio driver to drive
the them. The reasons are here are a tangent but lead to the discovery
of the inversion, which manifested as the LEDs being set to full
brightness at boot when we expected them to be off.
As we're driving the LEDs through leds-gpio, this means wending our way
through the gpiochip abstractions. So with that in mind we need to
describe an active-low GPIO configuration to drive the LEDs as though
they were GPIOs.
The set() gpiochip callback in leds-pca955x does the following:
...
if (val)
pca955x_led_set(&led->led_cdev, LED_FULL);
else
pca955x_led_set(&led->led_cdev, LED_OFF);
...
Where LED_FULL = 255. pca955x_led_set() in turn does:
...
switch (value) {
case LED_FULL:
ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_ON);
break;
...
Where PCA955X_LS_LED_ON is defined as:
#define PCA955X_LS_LED_ON 0x0 /* Output LOW */
So here we have some type confusion: We've crossed domains from GPIO
behaviour to LED behaviour without accounting for possible inversions
in the process.
Stepping back to leds-gpio for a moment, during probe() we call
create_gpio_led(), which eventually executes:
if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) {
state = gpiod_get_value_cansleep(led_dat->gpiod);
if (state < 0)
return state;
} else {
state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
}
...
ret = gpiod_direction_output(led_dat->gpiod, state);
In the devicetree the GPIO is annotated as active-low, and
gpiod_get_value_cansleep() handles this for us:
int gpiod_get_value_cansleep(const struct gpio_desc *desc)
{
int value;
might_sleep_if(extra_checks);
VALIDATE_DESC(desc);
value = _gpiod_get_raw_value(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
}
_gpiod_get_raw_value() in turn calls through the get() callback for the
gpiochip implementation, so returning to our get() implementation in
leds-pca955x we find we extract the raw value from hardware:
static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
{
struct pca955x *pca955x = gpiochip_get_data(gc);
struct pca955x_led *led = &pca955x->leds[offset];
u8 reg = pca955x_read_input(pca955x->client, led->led_num / 8);
return !!(reg & (1 << (led->led_num % 8)));
}
This behaviour is not symmetric with that of set(), where the val is
inverted by the driver.
Closing the loop on the GPIO_ACTIVE_LOW inversions,
gpiod_direction_output(), like gpiod_get_value_cansleep(), handles it
for us:
int gpiod_direction_output(struct gpio_desc *desc, int value)
{
VALIDATE_DESC(desc);
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
else
value = !!value;
return _gpiod_direction_output_raw(desc, value);
}
All-in-all, with a value of 'keep' for default-state property in a
leds-gpio child node, the current state of the hardware will in-fact be
inverted; precisely the opposite of what was intended.
Rework leds-pca955x so that we avoid the incorrect inversion and clarify
the semantics with respect to GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d1d90147c9 ]
Since commit 4ad23a9764 ("MD: use per-cpu counter for writes_pending"),
the wait_queue is only got invoked if THREAD_WAKEUP is not set previously.
With above change, I can see process_metadata_update could always hang on
the wait queue, because mddev->thread could stay on 'D' status and the
THREAD_WAKEUP flag is not cleared since there are lots of place to wake up
mddev->thread. Then deadlock happened as follows:
linux175:~ # ps aux|grep md|grep D
root 20117 0.0 0.0 0 0 ? D 03:45 0:00 [md0_raid1]
root 20125 0.0 0.0 0 0 ? D 03:45 0:00 [md0_cluster_rec]
linux175:~ # cat /proc/20117/stack
[<ffffffffa0635604>] dlm_lock_sync+0x94/0xd0 [md_cluster]
[<ffffffffa0635674>] lock_token+0x34/0xd0 [md_cluster]
[<ffffffffa0635804>] metadata_update_start+0x64/0x110 [md_cluster]
[<ffffffffa04d985b>] md_update_sb.part.58+0x9b/0x860 [md_mod]
[<ffffffffa04da035>] md_update_sb+0x15/0x30 [md_mod]
[<ffffffffa04dc066>] md_check_recovery+0x266/0x490 [md_mod]
[<ffffffffa06450e2>] raid1d+0x42/0x810 [raid1]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
linux175:~ # cat /proc/20125/stack
[<ffffffffa0636679>] recv_daemon+0x3f9/0x5c0 [md_cluster]
[<ffffffffa04d2252>] md_thread+0x122/0x150 [md_mod]
[<ffffffff81091741>] kthread+0x101/0x140
So let's revert the part of code in the commit to resovle the problem since
we can't get lots of benefits of previous change.
Fixes: 4ad23a9764 ("MD: use per-cpu counter for writes_pending")
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4831ca9e4a ]
The allocation for elem may fail (especially because we're using
GFP_ATOMIC) so best to check for a null return. This fixes a potential
null pointer dereference when assigning elem->pool.
Detected by CoverityScan CID#1357507 ("Dereference null return value")
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcfd6b839c ]
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e72a060151 ]
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
