[ Upstream commit c1a8d0a3ac ]
Under some circumstances driver will perform PHY reset in
ksz9031_read_status() to fix autoneg failure case (idle error count =
0xFF). When this happens ksz9031 will not detect link status change any
more when connecting to Netgear 1G switch (link can be recovered sometimes by
restarting netdevice "ifconfig down up"). Reproduced with TI am572x board
equipped with ksz9031 PHY while connecting to Netgear 1G switch.
Fix the issue by reconfiguring autonegotiation after PHY reset in
ksz9031_read_status().
Fixes: d2fd719bcb ("net/phy: micrel: Add workaround for bad autoneg")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 589bf32f09 ]
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e9 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02f510f326 ]
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a03a3692b ]
Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b22d73d668 ]
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7fbd9493f0 ]
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 748a240c58 ]
This fixes a hang issue seen when changing the MTU size from 1500 MTU
to 9000 MTU on both 5717 and 5719 chips. In discussion with Broadcom,
they've indicated that these chipsets have the same phy as the 57766
chipset, so the same workarounds apply. This has been tested by IBM
on both Power 8 and Power 9 systems as well as by Broadcom on x86
hardware and has been confirmed to resolve the hang issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aceef61ee5 ]
Sierra Wireless EM7565 is an Qualcomm MDM9x50 based M.2 modem.
The USB id is added to qmi_wwan.c to allow QMI communication
with the EM7565.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 178e5f57a8 ]
The enet IP only support 32 bit, it will use swiotlb buffer to do dma
mapping when xmit buffer DMA memory address is bigger than 4G in i.MX
platform. After stress suspend/resume test, it will print out:
log:
[12826.352864] fec 5b040000.ethernet: swiotlb buffer is full (sz: 191 bytes)
[12826.359676] DMA: Out of SW-IOMMU space for 191 bytes at device 5b040000.ethernet
[12826.367110] fec 5b040000.ethernet eth0: Tx DMA memory map failed
The issue is that the ready xmit buffers that are dma mapped but DMA still
don't copy them into fifo, once MAC restart, these DMA buffers are not unmapped.
So it should check the dma mapping buffer and unmap them.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0abc2a1038 upstream.
Commit caa4b02476e3(blk-map: call blk_queue_bounce from blk_rq_append_bio)
moves blk_queue_bounce() into blk_rq_append_bio(), but don't consider
the fact that the bounced bio becomes invisible to caller since the
parameter type is 'struct bio *'. Make it a pointer to a pointer to
a bio, so the caller sees the right bio also after a bounce.
Fixes: caa4b02476 ("blk-map: call blk_queue_bounce from blk_rq_append_bio")
Cc: Christoph Hellwig <hch@lst.de>
Reported-by: Michele Ballabio <barra_cuda@katamail.com>
(handling failure of blk_rq_append_bio(), only call bio_get() after
blk_rq_append_bio() returns OK)
Tested-by: Michele Ballabio <barra_cuda@katamail.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a50881bba upstream.
The XRC target QP create flow sets up qp_sec only if there is an IB link with
LSM security enabled. However, several other related uAPI entry points blindly
follow the qp_sec NULL pointer, resulting in a possible oops.
Check for NULL before using qp_sec.
Fixes: d291f1a652 ("IB/core: Enforce PKey security on QPs")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05d14e7b0c upstream.
If the input command length is larger than the kernel supports an error should
be returned in case the unsupported bytes are not cleared, instead of the
other way aroudn. This matches what all other callers of ib_is_udata_cleared
do and will avoid user ABI problems in the future.
Fixes: 189aba99e7 ("IB/uverbs: Extend modify_qp and support packet pacing")
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad9a3668a4 upstream.
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Fixes: 7c2344c3bb ("IB/mlx5: Implements disassociate_ucontext API")
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c009af473 upstream.
During driver init, various registers are saved to allow restoration
after an FLR or gen3 bump. Some of these registers are not available
in some circumstances (i.e. Virtual machines).
This bug makes the driver unusable when the PCI device is passed into
a VM, it fails during probe.
Delete unnecessary register read/write, and only access register if
the capability exists.
Fixes: a618b7e40a ("IB/hfi1: Move saving PCI values to a separate function")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8227033547 upstream.
Following commit 9427ecbed4 ("gpio: Rework of_gpiochip_set_names()
to use device property accessors"), "gpio-line-names" DT property is
not retrieved anymore when chip->parent is not set by the driver.
This is due to OF based property reads having been replaced by device
based property reads.
This patch fixes that by making use of
fwnode_property_read_string_array() instead of
device_property_read_string_array() and handing over either
of_fwnode_handle(chip->of_node) or dev_fwnode(chip->parent)
to that function.
Fixes: 9427ecbed4 ("gpio: Rework of_gpiochip_set_names() to use device property accessors")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55688c454 upstream.
If the RECV CQE is in error, ignore the MSN check. This was causing
recvs that were flushed into the sw cq to be completed with the wrong
status (BAD_MSN instead of FLUSHED).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2eecb2e04a upstream.
There are few reasons in mvneta_rx_swbm() function when received packet
is dropped. mvneta_rx_error() should be called only if error bit [16]
is set in rx descriptor.
[gregory.clement@free-electrons.com: add fixes tag]
Fixes: dc35a10f68 ("net: mvneta: bm: add support for hardware buffer management")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca5902a654 upstream.
When adding the RX queue association with each CPU, a typo was made in
the mvneta_cleanup_rxqs() function. This patch fixes it.
[gregory.clement@free-electrons.com: add commit log and fixes tag]
Fixes: 2dcf75e279 ("net: mvneta: Associate RX queues with each CPU")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4423c18e46 upstream.
When port connect to PHY in polling mode (with poll interval 1 sec),
port and phy link status must be synchronize in order don't loss link
change event.
[gregory.clement@free-electrons.com: add fixes tag]
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Tested-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19deaa217b upstream.
The alignment checks at pfn driver startup fail to properly account for
the 'start_pad' in the case where the namespace is misaligned relative
to its internal alignment. This is typically triggered in 1G aligned
namespace, but could theoretically trigger with small namespace
alignments. When this triggers the kernel reports messages of the form:
dax2.1: bad offset: 0x3c000000 dax disabled align: 0x40000000
Fixes: 1ee6667cd8 ("libnvdimm, pfn, dax: fix initialization vs autodetect...")
Reported-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24e3a7fb60 upstream.
Due to a spec misinterpretation, the Linux implementation of the BTT log
area had different padding scheme from other implementations, such as
UEFI and NVML.
This fixes the padding scheme, and defaults to it for new BTT layouts.
We attempt to detect the padding scheme in use when probing for an
existing BTT. If we detect the older/incompatible scheme, we continue
using it.
Reported-by: Juston Li <juston.li@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Fixes: 5212e11fde ("nd_btt: atomic sector updates")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 41fce90f26 upstream.
The following namespace configuration attempt:
# ndctl create-namespace -e namespace0.0 -m devdax -a 1G -f
libndctl: ndctl_dax_enable: dax0.1: failed to enable
Error: namespace0.0: failed to enable
failed to reconfigure namespace: No such device or address
...fails when the backing memory range is not physically aligned to 1G:
# cat /proc/iomem | grep Persistent
210000000-30fffffff : Persistent Memory (legacy)
In the above example the 4G persistent memory range starts and ends on a
256MB boundary.
We handle this case correctly when needing to handle cases that violate
section alignment (128MB) collisions against "System RAM", and we simply
need to extend that padding/truncation for the 1GB alignment use case.
Fixes: 315c562536 ("libnvdimm, pfn: add 'align' attribute...")
Reported-and-tested-by: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92411f6d7f upstream.
The commit 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap
initialization sequence") moved a bunch of logic around, but forgot to
update the gotos after the introduction of the err_free_dotclock label.
It means that if we fail later that the one introduced in that commit,
we'll just to the old label which isn't free the clock we created. This
will result in a breakage as soon as someone tries to do something with
that clock, since its resources will have been long reclaimed.
Fixes: 4c7f16d14a ("drm/sun4i: Fix TCON clock and regmap initialization sequence")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f83c1cebc731f0b4251f5ddd7b38c718cd79bb0b.1512662253.git-series.maxime.ripard@free-electrons.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2797c4a11f upstream.
From the shrinker paths, we want to relinquish the GPU and GGTT access to
the object, releasing the backing storage back to the system for
swapout. As a part of that process we would unpin the pages, marking
them for access by the CPU (for the swapout/swapin). However, if that
process was interrupted after unbind the vma, we missed a flush of the
inflight GGTT writes before we made that GTT space available again for
reuse, with the prospect that we would redirect them to another page.
The bug dates back to the introduction of multiple GGTT vma, but the
code itself dates to commit 02bef8f98d ("drm/i915: Unbind closed vma
for i915_gem_object_unbind()").
Fixes: 02bef8f98d ("drm/i915: Unbind closed vma for i915_gem_object_unbind()")
Fixes: c5ad54cf7d ("drm/i915: Use partial view in mmap fault handler")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204132513.7303-1-chris@chris-wilson.co.uk
(cherry picked from commit 5888fc9eac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61d2f2a057 upstream.
Our MMC host driver now issues a reset, instead of just deasserting
the reset control, since commit c34eda69ad ("mmc: sunxi: Reset the
device at probe time"). The sun9i-mmc clock driver does not support
this, and will fail, which results in MMC not probing.
This patch implements the reset callback by asserting the reset control,
then deasserting it after a small delay.
Fixes: 7a6fca879f ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171218035751.20661-1-wens@csie.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2b3c35359 upstream.
Guenter Roeck reported an interrupt storm on a prototype system which is
based on Cyan Chromebook. The root cause turned out to be a incorrectly
configured pin that triggers spurious interrupts. This will be fixed in
coreboot but currently we need to prevent the interrupt storm from
happening by masking all interrupts (but not GPEs) on those systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Fixes: bcb48cca23 ("pinctrl: cherryview: Do not mask all interrupts in probe")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 251c201bf4 upstream.
The Armada 3700 SPI controller has 2 ranges of prescaler coefficients.
One ranging from 0 to 15 by steps of 1, and one ranging from 0 to 30 by
steps of 2.
This commit fixes the prescaler coefficients that are over 15 so that it
uses the correct range of values. The prescaling coefficient is rounded
to the upper value if it is odd.
This was tested on Espressobin with spidev and a locigal analyser.
Signed-off-by: Maxime Chevallier <maxime.chevallier@smile.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a1314fa69 upstream.
When the core is configured in C_SPI_MODE > 0, it integrates a
lookup table that automatically configures the core in dual or quad mode
based on the command (first byte on the tx fifo).
Unfortunately, that list mode_?_memoy_*.mif does not contain all the
supported commands by the flash.
Since 4.14 spi-nor automatically tries to probe the flash using SFDP
(command 0x5a), and that command is not part of the list_mode table.
Whit the right combination of C_SPI_MODE and C_SPI_MEMORY this leads
into a stall that can only be recovered with a soft rest.
This patch detects this kind of stall and returns -EIO to the caller on
those commands. spi-nor can handle this error properly:
m25p80 spi0.0: Detected stall. Check C_SPI_MODE and C_SPI_MEMORY. 0x21 0x2404
m25p80 spi0.0: SPI transfer failed: -5
spi_master spi0: failed to transfer one message from queue
m25p80 spi0.0: s25sl064p (8192 Kbytes)
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcf3f1752a upstream.
Diva GSP card has built-in serial AUX port and ATI graphic card which simply
don't work and which both don't have external connectors. User Guides even
mention that those devices shouldn't be used.
So, prevent that Linux drivers try to enable those devices.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5839ee7389 upstream.
It is incorrect to call pci_restore_state() for devices in low-power
states (D1-D3), as that involves the restoration of MSI setup which
requires MMIO to be operational and that is only the case in D0.
However, pci_pm_thaw_noirq() may do that if the driver's "freeze"
callbacks put the device into a low-power state, so fix it by making
it force devices into D0 via pci_set_power_state() instead of trying
to "update" their power state which is pointless.
Fixes: e60514bd44 (PCI/PM: Restore the status of PCI devices across hibernation)
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Reported-by: Maarten Lankhorst <dev@mblankhorst.nl>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Maarten Lankhorst <dev@mblankhorst.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 85e9b13cbb upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent node was prematurely freed, while the
child node was leaked.
Note that the CONFIG_OF compile guard can be removed as
of_get_child_by_name() provides a !CONFIG_OF implementation which always
fails.
Fixes: 37e13cecaa ("mfd: Add support for Device Tree to twl6040")
Fixes: ca2cad6ae3 ("mfd: Fix twl6040 build failure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a423772de upstream.
A helper purported to look up a child node based on its name was using
the wrong of-helper and ended up prematurely freeing the parent of-node
while leaking any matching node.
To make things worse, any matching node would not even necessarily be a
child node as the whole device tree was searched depth-first starting at
the parent.
Fixes: 019a7e6b7b ("mfd: twl4030-audio: Add DT support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15d8374874 upstream.
On the Tegra124 Nyan-Big chromebook the very first SPI message sent to
the EC is failing.
The Tegra SPI driver configures the SPI chip-selects to be active-high
by default (and always has for many years). The EC SPI requires an
active-low chip-select and so the Tegra chip-select is reconfigured to
be active-low when the EC SPI driver calls spi_setup(). The problem is
that if the first SPI message to the EC is sent too soon after
reconfiguring the SPI chip-select, it fails.
The EC SPI driver prevents back-to-back SPI messages being sent too
soon by keeping track of the time the last transfer was sent via the
variable 'last_transfer_ns'. To prevent the very first transfer being
sent too soon, initialise the 'last_transfer_ns' variable after calling
spi_setup() and before sending the first SPI message.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adf6895754 upstream.
Integration testing with a BIOS that generates injected health event
notifications fails to communicate those events to userspace. The nfit
driver neglects to link the ACPI DIMM device with the necessary driver
data so acpi_nvdimm_notify() fails this lookup:
nfit_mem = dev_get_drvdata(dev);
if (nfit_mem && nfit_mem->flags_attr)
sysfs_notify_dirent(nfit_mem->flags_attr);
Add the necessary linkage when installing the notification handler and
clean it up when the nfit driver instance is torn down.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: ba9c8dd3c2 ("acpi, nfit: add dimm device notification support")
Reported-by: Daniel Osawa <daniel.k.osawa@intel.com>
Tested-by: Daniel Osawa <daniel.k.osawa@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb82e0b4a7 upstream.
The commit f6f8285132 ("pstore: pass allocated memory region back to
caller") changed the check of the return value from erst_read() in
erst_reader() in the following way:
if (len == -ENOENT)
goto skip;
- else if (len < 0) {
- rc = -1;
+ else if (len < sizeof(*rcd)) {
+ rc = -EIO;
goto out;
This introduced another bug: since the comparison with sizeof() is
cast to unsigned, a negative len value doesn't hit any longer.
As a result, when an error is returned from erst_read(), the code
falls through, and it may eventually lead to some weird thing like
memory corruption.
This patch adds the negative error value check more explicitly for
addressing the issue.
Fixes: f6f8285132 (pstore: pass allocated memory region back to caller)
Tested-by: Jerry Tang <jtang@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bff5bf9db1 upstream.
Sending the switch state change twice within the same frame is invalid
evdev protocol and only works if the client handles keys immediately as
well. Processing events immediately is incorrect, it forces a fake
order of events that does not exist on the device.
Recent versions of libinput changed to only process the device state and
SYN_REPORT time, so now the key event is lost.
https://bugs.freedesktop.org/show_bug.cgi?id=104041
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2b033260 upstream.
The DT specifies a threshold of 65000, we setup the register with a value in
the temperature resolution for the controller, 64656.
When we reach 64656, the interrupt fires, the interrupt is disabled. Then the
irq thread runs and calls thermal_zone_device_update() which will call in turn
hisi_thermal_get_temp().
The function will look if the temperature decreased, assuming it was more than
65000, but that is not the case because the current temperature is 64656
(because of the rounding when setting the threshold). This condition being
true, we re-enable the interrupt which fires immediately after exiting the irq
thread. That happens again and again until the temperature goes to more than
65000.
Potentially, there is here an interrupt storm if the temperature stabilizes at
this temperature. A very unlikely case but possible.
In any case, it does not make sense to handle dozens of alarm interrupt for
nothing.
Fix this by rounding the threshold value to the controller resolution so the
check against the threshold is consistent with the one set in the controller.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 48880b979c upstream.
The step and the base temperature are fixed values, we can simplify the
computation by converting the base temperature to milli celsius and use a
pre-computed step value. That saves us a lot of mult + div for nothing at
runtime.
Take also the opportunity to change the function names to be consistent with
the rest of the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cb4de785c upstream.
The threaded interrupt for the alarm interrupt is requested before the
temperature controller is setup. This one can fire an interrupt immediately
leading to a kernel panic as the sensor data is not initialized.
In order to prevent that, move the threaded irq after the Tsensor is setup.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c176b10b02 upstream.
The interrupt for the temperature threshold is not enabled at the end of the
probe function, enable it after the setup is complete.
On the other side, the irq_enabled is not correctly set as we are checking if
the interrupt is masked where 'yes' means irq_enabled=false.
irq_get_irqchip_state(data->irq, IRQCHIP_STATE_MASKED,
&data->irq_enabled);
As we are always enabling the interrupt, it is pointless to check if
the interrupt is masked or not, just set irq_enabled to 'true'.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b77eb45e0d ]
Do not include EM specified MAC address in total MACs of the
UC MAC list.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4bbdfe2560 ]
Clear the MAC table digest when the MAC table is freed.
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Scott Franco <safranco@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af2eca5320 ]
The incoming mode might have a missing vrefresh field if it came from
drmModeSetCrtc(), which the kernel is supposed to calculate using
drm_mode_vrefresh(). We could either use that or the adjusted_mode's
original vrefresh value.
However, we can maintain a more exact vrefresh value (not just the
integer approximation), by scaling by the ratio of our clocks.
v2: Use math suggested by Andrzej Hajda instead.
v3: Simplify math now that adjusted_mode->clock isn't padded.
v4: Drop some parens.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815234722.20700-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f187851b9b ]
When failing to enter broadcast timer mode for an idle state that
requires it, a new state is selected that does not require broadcast,
but the broadcast variable remains set. This causes
tick_broadcast_exit to be called despite not having entered broadcast
mode.
This causes the WARN_ON_ONCE(!irqs_disabled()) to trigger in some
cases. It does not appear to cause problems for code today, but seems
to violate the interface so should be fixed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74717b28cb ]
If there is any non expired timer in the queue, the RTC alarm is never set.
This is an issue when adding a timer that expires before the next non
expired timer.
Ensure the RTC alarm is set in that case.
Fixes: 2b2f5ff00f ("rtc: interface: ignore expired timers when enqueuing new timers")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f3ed79188 ]
The HDMI DDC clock found in the CCU is the parent of the actual DDC
clock within the HDMI controller. That clock is also named "hdmi-ddc".
Rename the one in the CCU to "ddc". This makes more sense than renaming
the one in the HDMI controller to something else.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e437b1d7e ]
After the loop in hns_roce_v1_mr_free_work_fn function, it is possible that
all qps will have been freed (in which case ne will be 0). If that
happens, then later in the function when we dereference hr_qp we will
get an exception. Check ne is not 0 to make sure we actually have an
hr_qp left to work on.
This patch fixes the smatch error as below:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:1009 hns_roce_v1_mr_free_work_fn()
error: we previously assumed 'hr_qp' could be null
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e876a8a7e9 ]
State is initially reported as UNKNOWN. Before register call
netif_carrier_off(). Once the device is opened, call netif_carrier_on() in
order to set the state to UP.
Signed-off-by: Mick Tarsel <mjtarsel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
