Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
common place. We already have bcm47xx_nvram in firmware path and SPROM
should fit there as well.
This driver is responsible for parsing SoC configuration data into a
struct shared between ssb and bcma buses.
This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0
(ARCH_BCM_5301X).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12210/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The HDA links can be switched off when not is use, similarly
command DMA can be stopped as well. This calls for a reference
counting mechanism on the link by it's users to manage the link
power. The DMA can be turned off when all links are off
For this we add two APIs
snd_hdac_ext_bus_link_get
snd_hdac_ext_bus_link_put
They help users to turn up/down link and manage the DMA as well
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This will provide fully accuracy to the mapcount calculation in the
write protect faults, so page pinning will not get broken by false
positive copy-on-writes.
total_mapcount() isn't the right calculation needed in
reuse_swap_page(), so this introduces a page_trans_huge_mapcount()
that is effectively the full accurate return value for page_mapcount()
if dealing with Transparent Hugepages, however we only use the
page_trans_huge_mapcount() during COW faults where it strictly needed,
due to its higher runtime cost.
This also provide at practical zero cost the total_mapcount
information which is needed to know if we can still relocate the page
anon_vma to the local vma. If page_trans_huge_mapcount() returns 1 we
can reuse the page no matter if it's a pte or a pmd_trans_huge
triggering the fault, but we can only relocate the page anon_vma to
the local vma->anon_vma if we're sure it's only this "vma" mapping the
whole THP physical range.
Kirill A. Shutemov discovered the problem with moving the page
anon_vma to the local vma->anon_vma in a previous version of this
patch and another problem in the way page_move_anon_rmap() was called.
Andrew Morton discovered that CONFIG_SWAP=n wouldn't build in a
previous version, because reuse_swap_page must be a macro to call
page_trans_huge_mapcount from swap.h, so this uses a macro again
instead of an inline function. With this change at least it's a less
dangerous usage than it was before, because "page" is used only once
now, while with the previous code reuse_swap_page(page++) would have
called page_mapcount on page+1 and it would have increased page twice
instead of just once.
Dean Luick noticed an uninitialized variable that could result in a
rmap inefficiency for the non-THP case in a previous version.
Mike Marciniszyn said:
: Our RDMA tests are seeing an issue with memory locking that bisects to
: commit 61f5d698cc ("mm: re-enable THP")
:
: The test program registers two rather large MRs (512M) and RDMA
: writes data to a passive peer using the first and RDMA reads it back
: into the second MR and compares that data. The sizes are chosen randomly
: between 0 and 1024 bytes.
:
: The test will get through a few (<= 4 iterations) and then gets a
: compare error.
:
: Tracing indicates the kernel logical addresses associated with the individual
: pages at registration ARE correct , the data in the "RDMA read response only"
: packets ARE correct.
:
: The "corruption" occurs when the packet crosse two pages that are not physically
: contiguous. The second page reads back as zero in the program.
:
: It looks like the user VA at the point of the compare error no longer points to
: the same physical address as was registered.
:
: This patch totally resolves the issue!
Link: http://lkml.kernel.org/r/1462547040-1737-2-git-send-email-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: "Kirill A. Shutemov" <kirill@shutemov.name>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Josh Collier <josh.d.collier@intel.com>
Cc: Marc Haber <mh+linux-kernel@zugschlus.de>
Cc: <stable@vger.kernel.org> [4.5]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Qualcomm WCNSS can crash by watchdog or a fatal software error. Add
these types to the list of remoteproc crash reasons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the needed mlx5_ifc hardware bits and structs
for the following features:
* Add vport to steering commands for SRIOV ACL support
* Add mlcr, pcmr and mcia registers for dump module EEPROM
* Add support for FCS, beacon led and disable_link bits to
hca caps
* Add CQE period mode bit in CQ context for CQE based CQ
moderation support
* Add umr SQ bit for fragmented memory registration
* Add needed bits and caps for Striding RQ support
In-order to avoid possible future conflicts between rdma and
net-next we added all expected updates to this file for this release.
If more changes will be submitted, we plan to do it only through
one of the subsystems, probably net-next.
All updated bits in this patch will be later used in
the up-coming submissions to net-next and rdma trees.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All reserved fields after early_vf_enable are off by 1, since
early_vf_enable was not explicitly declared as array of size 1.
Reserved field before cqe_zip had a wrong size, it should
be 0x80 + 0x3f.
Fixes: b084444459 ("net/mlx5_core: Introduce access function to read internal timer ")
Fixes: b4ff3a36d3 ("net/mlx5: Use offset based reserved field names in the IFC header file")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
-----BEGIN PGP SIGNATURE-----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=QNxF
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more work for 4.7, notably:
* completion and fixups of nla_put_64_64bit() work
* remove a/b/g/n from wext nickname to avoid confusion
with 11ac (which wouldn't even fit fully there due to
string length restrictions)
along with some other minor changes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 086d7f804e ("ASoC: Convert WM8962 MICBIAS to a supply widget",
2011-09-23) says:
A supply widget is generally clearer than a MICBIAS widget and a
mic bias is just a type of supply so use a supply widget for the
MICBIAS. This also avoids confusion with the routing when
connected to multiple inputs.
but this has never been documented as a policy. Add some comments to
make it clear.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No functional changes in this patch.
PCI I/O space mapping code does not depend on OF; therefore it can be moved
to PCI core code. This way we will be able to use it, e.g., in ACPI PCI
code.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Liviu Dudau <Liviu.Dudau@arm.com>
Support of 0.5% down-spread is required for DisplayPort Specification
Version 1.1 Sink.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[treding@nvidia.com: rename to DP_MAX_DOWNSPREAD_0_5]
Signed-off-by: Thierry Reding <treding@nvidia.com>
When using RSS, frames might not be processed in the correct order,
and thus AP_LINK_PS must be used; most likely with firmware keeping
track of the powersave state, this is the case in iwlwifi now.
In this case, the driver can use ieee80211_sta_ps_transition() to
still have mac80211 manage powersave buffering. However, for U-APSD
and PS-Poll this isn't sufficient. If the device can't manage that
entirely on its own, mac80211's code should be used.
To allow this, export two functions: ieee80211_sta_uapsd_trigger()
and ieee80211_sta_pspoll().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no harm in having drivers read the list, since they can
use RCU protection or RTNL locking; allow this to not require
each and every driver to also implement its own bookkeeping.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows finding vendor IE from a specific vendor.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardware (iwlwifi an example) de-aggregate AMSDUs and copy the IV
as is to the generated MPDUs, so the same PN appears in multiple
packets without being a replay attack. Allow driver to explicitly
indicate that a frame is allowed to have the same PN as the previous
frame.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
tsk_nr_cpus_allowed() is an accessor for task->nr_cpus_allowed which allows
us to change the representation of ->nr_cpus_allowed if required.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1462969411-17735-2-git-send-email-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for the AXI Central Direct Memory Access
(AXI CDMA) core to the existing vdma driver, AXI CDMA is a
soft Xilinx IP core that provides high-bandwidth
Direct Memory Access(DMA) between a memory-mapped
source address and a memory-mapped destination address.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the AXI Direct Memory Access (AXI DMA)
core in the existing vdma driver, AXI DMA Core is a
soft Xilinx IP core that provides high-bandwidth
direct memory access between memory and AXI4-Stream
type target peripherals.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Device should be configured by default to VEB once VFs are active.
This changes the configuration of both PFs' and VFs' vports into enabling
tx-switching once sriov is enabled.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the user to view the VF configuration by observing the PF's
device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in `ndo_set_vf_spoofchk' for allowing PF control over
its VF spoof-checking configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in 2 ndo that allow PF to tweak the VF's view of the
link - `ndo_set_vf_link_state' to allow it a view independent of the PF's,
and `ndo_set_vf_rate' which would allow the PF to limit the VF speed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the PF to enforce the VF's mac.
i.e., by using `ip link ... vf <x> mac <value>'.
While a MAC is forced, PF would prevent the VF from configuring any other
MAC.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for PF control over the VF vlan configuration.
I.e., `ip link ... vf <x> vlan <vid>' should now be supported.
1. <vid> != 0 => VF receives [unknowingly] only traffic tagged by
<vid> and tags all outgoing traffic sent by VF with <vid>.
2. <vid> == 0 ==> Remove the pvid configuration, reverting to previous.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While previous patches have already added the necessary logic to probe
VFs as well as enabling them in the HW, this patch adds the ability to
support VF FLR & SRIOV disable.
It then wraps both flows together into the first IOV callback to be
provided to the protocol driver - `configure'. This would later to be used
to enable and disable SRIOV in the adapter.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the qed VFs for the first time -
The vfs are limited functions, with a very different PCI bar structure
[when compared with PFs] to better impose the related security demands
associated with them.
This patch includes the logic neccesary to allow VFs to successfully probe
[without actually adding the ability to enable iov].
This includes diverging all the flows that would occur as part of the pci
probe of the driver, preventing VF from accessing registers/memories it
can't and instead utilize the VF->PF channel to query the PF for needed
information.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Communication between VF and PF is based on a dedicated HW channel;
VF will prepare a messge, and by signaling the HW the PF would get a
notification of that message existance. The PF would then copy the
message, process it and DMA an answer back to the VF as a response.
The messages themselves are TLV-based - allowing easier backward/forward
compatibility.
This patch adds the infrastructure of the channel on the PF side -
starting with the arrival of the notification and ending with DMAing
the response back to the VF.
It also adds a dummy-response as reference, as it only lays the
groundwork of the communication; it doesn't really add support of any
actual messages.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zM22
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CQE compression feature is meant to save PCIe bandwidth by
compressing few CQEs into smaller amount of bytes on PCIe.
CQE compression can be selectively enabled per CQ. By default
is disabled for now and will be enabled later on.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure contains a dsa_chip_data member called pd.
However in the rest of the code, pd is used for dsa_platform_data.
This is confusing. Rename it cd, which is already often used in dsa.c
and slave.c for this data type.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch drivers only use the master_dev member for dev_info()
messages. Now that the device is passed to the old style probe, and
new style drivers are probed as true linux drivers, this is no longer
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications such as OSPF and BFD need the original ingress device not
the VRF device; the latter can be derived from the former. To that end
add the skb_iif to inet_skb_parm and set it in ipv4 code after clearing
the skb control buffer similar to IPv6. From there the pktinfo can just
pull it from cb with the PKTINFO_SKB_CB cast.
The previous patch moving the skb->dev change to L3 means nothing else
is needed for IPv6; it just works.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we don't support a mechanism for bypassing IRQs, don't register as
a consumer. This eliminates meaningless dev_info()s when the connect
fails between producer and consumer, such as on AMD systems where
kvm_x86_ops->update_pi_irte is not implemented
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A NULL token is meaningless and can only lead to unintended problems.
Error on registration with a NULL token, ignore de-registrations with
a NULL token.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.
This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.
The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.
This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit c896939f7c ("KVM: use heuristic for fast VCPU lookup by id") added
a return path that prevents vcpu ids to exceed KVM_MAX_VCPUS. This is a
problem for powerpc where vcpu ids can grow up to 8*KVM_MAX_VCPUS.
This patch simply reverses the logic so that we only try fast path if the
vcpu id can be tried as an index in kvm->vcpus[]. The slow path is not
affected by the change.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reworks our stage 2 page table handling to have page table manipulation
macros separate from those of the host systems as the underlying
hardware page tables can be configured to be noticably different in
layout from the stage 1 page tables used by the host.
Adds 16K page size support based on the above.
Adds a generic firmware probing layer for the timer and GIC so that KVM
initializes using the same logic based on both ACPI and FDT.
Finally adds support for hardware updating of the access flag.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXMzKGAAoJEEtpOizt6ddyQ0AH/RS1tn3obEnujzD1yFeiSNS7
kBTwDEDdsAE7RJ12c43knfGaO4JO9+V2o1F5/16+/mjWDUJwAsm0yzSxvlxiS/+o
Q3QIfAbXxj/xia+sDFEtuSpRLL7Kl9oYeKBc5BijobvIQ5PKWm41kxehS8phMovQ
hiC2WQ5Wm1ww9L6AcI3gf8jqj4GJ/v+RSWzMTmPA7Wm7l03VGFn+G6AOnO0Rx6Fp
aRhI3dgvMAeMV8DXKTCdZggPrZ/ipLU+LgU+FwUXx2Ru9VfjU94MBEJG3FsTjNM0
UT1NLQ3kZaiYjlW/tN8WCXQDK1AUFDWUCHW7p77mq9w3cSylQBUlKbjRzTtjBsM=
=8PZF
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for Linux v4.7
Reworks our stage 2 page table handling to have page table manipulation
macros separate from those of the host systems as the underlying
hardware page tables can be configured to be noticably different in
layout from the stage 1 page tables used by the host.
Adds 16K page size support based on the above.
Adds a generic firmware probing layer for the timer and GIC so that KVM
initializes using the same logic based on both ACPI and FDT.
Finally adds support for hardware updating of the access flag.
Prevent memory scribble by checking that ioctl buffer size parameters
are sane.
Without this check, on 32 bits system, if .insize = 0xffffffff - 20 and
.outsize the amount to scribble, we would overflow, allocate a small
amounts and be able to write outside of the malloc'ed area.
Adding a hard limit allows argument checking of the ioctl. With the
current EC, it is expected .insize and .outsize to be at around 512 bytes
or less.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace 2 arguments (cnt and rtt) in the congestion control modules'
pkts_acked() function with a struct. This will allow adding more
information without having to modify existing congestion control
modules (tcp_nv in particular needs bytes in flight when packet
was sent).
As proposed by Neal Cardwell in his comments to the tcp_nv patch.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces reserve_new_blocks to make preallocation of multi
blocks as in batch operation, so it can avoid lots of redundant
operation, result in better performance.
In virtual machine, with rotational device:
time fallocate -l 32G /mnt/f2fs/file
Before:
real 0m4.584s
user 0m0.000s
sys 0m4.580s
After:
real 0m0.292s
user 0m0.000s
sys 0m0.272s
In x86, with SSD:
time fallocate -l 500G $MNT/testfile
Before : 24.758 s
After : 1.604 s
Signed-off-by: Chao Yu <yuchao0@huawei.com>
[Jaegeuk Kim: fix bugs and add performance numbers measured in x86.]
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
