Here are a number of small tty and serial driver fixes for 4.5-rc4 that
resolve some reported issues.
One of them got reverted as it wasn't correct based on testing, and all
have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbAzkEACgkQMUfUDdst+ylE4QCfXW10ziXSblRUIJubEm45Qhn2
WJAAoLFMd/eER2TFkBl4E2Y3I7HUaL5d
=V2Vb
-----END PGP SIGNATURE-----
Merge tag 'tty-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 4.5-rc4
that resolve some reported issues.
One of them got reverted as it wasn't correct based on testing, and
all have been in linux-next for a while"
* tag 'tty-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "8250: uniphier: allow modular build with 8250 console"
pty: make sure super_block is still valid in final /dev/tty close
pty: fix possible use after free of tty->driver_data
tty: Add support for PCIe WCH382 2S multi-IO card
serial/omap: mark wait_for_xmitr as __maybe_unused
serial: omap: Prevent DoS using unprivileged ioctl(TIOCSRS485)
8250: uniphier: allow modular build with 8250 console
tty: Drop krefs for interrupted tty lock
Pull timer fix from Thomas Gleixner:
"A single fix preventing a 32bit overflow in timespec/val to cputime
conversions on 32bit machines"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LIQe
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO device support, features and cleanups for the 4.6 cycle.
New Device Support
* Apex stx104 DAC
- new driver for this PC104 board. Right now DAC support only.
* ADI ad5064
- Add support for ad5625, ad5627, ad5645, ad5665, ad5667 DACs.
- Add support for Linear Technology ltc2606, ltc2607, ltc2609, ltc2616,
ltc2617, ltc2619, ltc2626, ltc2627 and ltc2629.
* ADI ad7192
- add support for the ad7193
* Invensense mpu6050
- substantial rework of driver to use regmap allowing SPI support extending
the now split driver to cover the MPU6000.
* TI adc0832
- new driver supporting ADC0831, ADC0832, ADC0834 and ADC0838 ADCs.
* TI ads1015
- new driver, note that there is an existing hwmon driver. The long term
intention is to probably remove the hwmon driver but for now we just have
guards in place to ensure this driver is not built if that one is enabled.
* TI afe4403
- new driver for this heart rate monitor / pulse oximeter front end chip.
* TI afe4404
- new driver for this heart rate monitor / pulse oximeter front end chip.
Staging Graduations
* mxs-lradc
- A combined general purpose and touch screen (input) device driver.
Originally held in staging to allow reworking into and MFD but as
that wasn't happening and isn't an absolute requirement we are moving
it out of staging.
Driver new features
* ms5611
- triggered buffer support
- IIO_CHAN_INFO_SCALE to aid the triggered buffer support.
Driver cleanups / reworks / fixes
* ad5064
- Use an enum for the register map layout to allow support of additional
chips (precursor to the new support listed above).
- Structural driver changes to allow support of the slightly different
handling for the ltc parts above.
* ad5933
- drop an exceptional & unnecessary for a function pointer.
* ad7606
- Cleanup the repeated copies of pm ops.
- consolidate the various channels specs via a sport of rearranging so only
one version is needed.
* atlas ph sensor
- add select IRQ_WORK
* hmc8543 (soon to move out of staging)
- Comment style fixes
- functionality of suspend and resume was swapped.
* spear-adc
- use devm_clk_dev instead of managing the clk lifetime by hand.
Core
* Use new dmaengine_terminate_sync call to avoid a theoretical race.
* Fix docs for mlock in struct iio_dev as it is correctly taken in some
drivers (docs used to say for core only).
* Add a helper function for calculating the scan index storage size within
the core cutting out some cut and paste versions of the same code.
most of the clock tree structures on i.MX6 Quad Plus are
same as on i.MX6Q. there still some differences between
these two SOCs. compared to the i.XM6Q, the differents of
clocks on i.MX6QP is mainly on:
1. New clock gate added to support the PRE and PRG modules
2. 24MHz OSC clock option added to the UART, IPG, ECSPI, and
CAN clock roots.
3. MMDC channel 1 clock gate is now controllable.
4. clock gating added to the LDB_DIx_IPU clocks on i.MX6QP
5. EMI clock root divider fix
6. other updates fo CSCMRx, CSCDRx and CS2CDR registers.
detailed infomation, please refer to the i.MX6QP RM.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the long awaited series to address a set of bugs around
active I/O remote-port LUN_RESET, as well as properly handling this
same case with concurrent fabric driver session disconnect ->
reconnect.
Note this set of LUN_RESET bug-fixes has been surviving extended
testing on both v4.5-rc1 and v3.14.y code over the last weeks, and is
CC'ed for stable as it's something folks using multiple ESX connected
hosts with slow backends can certainly trigger.
The highlights also include:
- Fix WRITE_SAME/DISCARD emulation 4k sector conversion in
target/iblock (Mike Christie)
- Fix TMR abort interaction and AIO type TMR response in qla2xxx
target (Quinn Tran + Swapnil Nagle)
- Fix >= v3.17 stale descriptor pointer regression in qla2xxx target
(Quinn Tran)
- Fix >= v4.5-rc1 return regression with unmap_zeros_data_store new
configfs store handler (nab)
- Add CPU affinity flag + convert qla2xxx to use bit (Quinn + HCH +
Bart)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: use TARGET_SCF_USE_CPUID flag to indiate CPU Affinity
target/transport: add flag to indicate CPU Affinity is observed
target: Fix incorrect unmap_zeroes_data_store return
qla2xxx: Use ATIO type to send correct tmr response
qla2xxx: Fix stale pointer access.
target/user: Fix cast from pointer to phys_addr_t
target: Drop legacy se_cmd->task_stop_comp + REQUEST_STOP usage
target: Fix race with SCF_SEND_DELAYED_TAS handling
target: Fix remote-port TMR ABORT + se_cmd fabric stop
target: Fix TAS handling for multi-session se_node_acls
target: Fix LUN_RESET active TMR descriptor handling
target: Fix LUN_RESET active I/O handling for ACK_KREF
qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM
qla2xxx: Fix warning reported by static checker
target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors
Export fetch_or() that's implemented and used internally by the
scheduler. We are going to use it for NO_HZ so make it generally
available.
Reviewed-by: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Merge fixes from Andrew Morton:
"10 fixes"
The lockdep hlist conversion is in the locking tree too, waiting for the
next merge window. Andrew thought it should go in now. I'll take it,
since it fixes a real problem and looks trivially correct (famous last
words).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/x86/Kconfig: CONFIG_X86_UV should depend on CONFIG_EFI
mm: fix pfn_t vs highmem
kernel/locking/lockdep.c: convert hash tables to hlists
mm,thp: fix spellos in describing __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
mm,thp: khugepaged: call pte flush at the time of collapse
mm/backing-dev.c: fix error path in wb_init()
mm, dax: check for pmd_none() after split_huge_pmd()
vsprintf: kptr_restrict is okay in IRQ when 2
mm: fix filemap.c kernel doc warning
ubsan: cosmetic fix to Kconfig text
As of commit 876fe76d79
"mtd: maps: physmap: Add reference counter to set_vpp()"
the comment in the header file is incorrect and misleading.
Fix it up.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Parsons <lost.distance@yahoo.com>
Fixes: 876fe76d79 ("mtd: maps: physmap: Add reference counter to set_vpp()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
A set of seven fixes. Two regressions in the new hisi_sas arm driver, a
blacklist entry for the marvell console which was causing a reset cascade
without it, a race fix in the WRITE_SAME/DISCARD routines, a retry fix for the
rdac driver, without which, it would prematurely return EIO and a couple of
fixes for the hyper-v storvsc driver.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWvXAcAAoJEDeqqVYsXL0MAdkIAMC3LDF4tnfkgDmgl/vHAJTH
q7UEOGzMv3XubgZXQRr190eWwCkpo0D0eQBqLIwV6AYMCdauTZ/kZ9Nd3ENn4+F1
qZa+YU1vYstIS6hJkt/byZojH7bht/ueaiqxXxz21T6kNrQJt44pn2jFfUQeZoMg
x5A16cUNdIl5H7F37qaerP/A4dNzFYGcdBJZoJZi90L7V9tzOBoaau1FdvtjFg9o
V4N92JTpm0/I02h9znXhwoHpinREg705rB7duKHUQ82F8hBZvuXkPVibXD/xhjuy
CXavuF1xeb/xjFh4X3a58SNRuxDuo6b8vYb8W6J0yi9j9O1iBe8XEIxgMRR6OJE=
=i5+x
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of seven fixes:
Two regressions in the new hisi_sas arm driver, a blacklist entry for
the marvell console which was causing a reset cascade without it, a
race fix in the WRITE_SAME/DISCARD routines, a retry fix for the rdac
driver, without which, it would prematurely return EIO and a couple of
fixes for the hyper-v storvsc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
block/sd: Return -EREMOTEIO when WRITE SAME and DISCARD are disabled
SCSI: Add Marvell Console to VPD blacklist
scsi_dh_rdac: always retry MODE SELECT on command lock violation
storvsc: Use the specified target ID in device lookup
storvsc: Install the storvsc specific timeout handler for FC devices
hisi_sas: fix v1 hw check for slot error
hisi_sas: add dependency for HAS_IOMEM
The userspace might need some sort of cache coherency management e.g. when CPU
and GPU domains are being accessed through dma-buf at the same time. To
circumvent this problem there are begin/end coherency markers, that forward
directly to existing dma-buf device drivers vfunc hooks. Userspace can make use
of those markers through the DMA_BUF_IOCTL_SYNC ioctl. The sequence would be
used like following:
- mmap dma-buf fd
- for each drawing/upload cycle in CPU 1. SYNC_START ioctl, 2. read/write
to mmap area 3. SYNC_END ioctl. This can be repeated as often as you
want (with the new data being consumed by the GPU or say scanout device)
- munmap once you don't need the buffer any more
v2 (Tiago): Fix header file type names (u64 -> __u64)
v3 (Tiago): Add documentation. Use enum dma_buf_sync_flags to the begin/end
dma-buf functions. Check for overflows in start/length.
v4 (Tiago): use 2d regions for sync.
v5 (Tiago): forget about 2d regions (v4); use _IOW in DMA_BUF_IOCTL_SYNC and
remove range information from struct dma_buf_sync.
v6 (Tiago): use __u64 structured padded flags instead enum. Adjust
documentation about the recommendation on using sync ioctls.
v7 (Tiago): Alex' nit on flags definition and being even more wording in the
doc about sync usage.
v9 (Tiago): remove useless is_dma_buf_file check. Fix sync.flags conditionals
and its mask order check. Add <linux/types.h> include in dma-buf.h.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Tiago Vignatti <tiago.vignatti@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455228291-29640-1-git-send-email-tiago.vignatti@intel.com
This module is heavily based on i2c-dev. Once loaded, it provides one
dev node per DP AUX channel, named drm_dp_auxN, where N is an integer.
It's possible to know which connector owns this aux channel by looking
at the respective sysfs /sys/class/drm_aux_dev/drm_dp_auxN/connector, if
the connector device pointer was correctly set in the aux helper struct.
Two main operations are provided on the registers read and write. The
address of the register to be read or written is given using lseek. The
seek position is updated upon read or write.
v2:
- lseek is used to select the register to read/write
- read/write are used instead of ioctl
- no blocking_notifier is used, just a direct callback
v3:
- use drm_dp_aux_dev prefix for public functions
- chardev is named drm_dp_auxN
- read/write don't allocate a buffer anymore, and transfer up to 16 bytes a
time
- remove notifier list from the implementation
- option on menuconfig is now a boolean
- add inline stub functions to avoid breakage when this option is disabled
v4:
- fix build system changes - actually disable this module when not selected.
v5:
- Use kref to avoid device closing while still in use
- Don't use list, use an idr for storing aux_dev
- Remove "connector" attribute
- set aux.dev to the connector drm_connector device, instead of
drm_device
v6:
- Use atomic_t for usage count
- Use a mutex instead of spinlock for idr lock
- Destroy chardev immediately on unregister
- other minor suggestions from Ville
v7:
- style fixes
- error handling fixes
v8:
- more error handling fixes
v9:
- remove module_init and module_exit, and add drm_dp_aux_dev_init/exit
to drm_kms_helper_init/exit.
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453417821-2811-3-git-send-email-rafael.antognolli@intel.com
The module_init and module_exit functions will start here, and call the
subsequent init's and exit's.
v10:
- Keep __init on drm_fb_helper init function.
- Move MODULE_* macros to the common file.
Signed-off-by: Rafael Antognolli <rafael.antognolli@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1453417821-2811-2-git-send-email-rafael.antognolli@intel.com
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only protocol affected at present is Geneve.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arithmetic properties of the ones-complement checksum mean that a
correctly checksummed inner packet, including its checksum, has a ones
complement sum depending only on whatever value was used to initialise
the checksum field before checksumming (in the case of TCP and UDP,
this is the ones complement sum of the pseudo header, complemented).
Consequently, if we are going to offload the inner checksum with
CHECKSUM_PARTIAL, we can compute the outer checksum based only on the
packed data not covered by the inner checksum, and the initial value of
the inner checksum field.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x driver assumes the device is i2c based. This is not the
case with later chips, which use a proprietary 2 wire serial bus
by Allwinner called "Reduced Serial Bus".
This patch follows the example of mfd/wm831x and splits it into
an interface independent core, and an i2c specific glue layer.
MFD_AXP20X and the new MFD_AXP20X_I2C are changed to tristate
symbols, allowing the driver to be built as modules.
Whitespace and other style errors in the moved i2c specific code
have been fixed. Included but unused header files are removed as
well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This commit adds support to the eeprom_93x46 driver allowing a GPIO line
to function as a 'select' or 'enable' signal prior to accessing the
EEPROM.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atmel devices in this family have some quirks not found in other similar
chips - they do not support a sequential read of the entire EEPROM
contents, and the control word sent at the start of each operation
varies in bit length.
This commit adds quirk support to the driver and modifies the read
implementation to support non-sequential reads for consistency with
other misc/eeprom drivers.
Tested on a custom Freescale VF610-based platform, with an AT93C46D
device attached via dspi2. The spi-gpio driver was used to allow the
necessary non-byte-sized transfers.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Tested-by: Chris Healy <chris.healy@zii.aero>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pfn_t type uses an unsigned long to store a pfn + flags value. On a
64-bit platform the upper 12 bits of an unsigned long are never used for
storing the value of a pfn. However, this is not true on highmem
platforms, all 32-bits of a pfn value are used to address a 44-bit
physical address space. A pfn_t needs to store a 64-bit value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=112211
Fixes: 01c8f1c44b ("mm, dax, gpu: convert vm_insert_mixed to pfn_t")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Stuart Foster <smf.linux@ntlworld.com>
Reported-by: Julian Margetson <runaway@candw.ms>
Tested-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike said:
: CONFIG_UBSAN_ALIGNMENT breaks x86-64 kernel with lockdep enabled, i. e
: kernel with CONFIG_UBSAN_ALIGNMENT fails to load without even any error
: message.
:
: The problem is that ubsan callbacks use spinlocks and might be called
: before lockdep is initialized. Particularly this line in the
: reserve_ebda_region function causes problem:
:
: lowmem = *(unsigned short *)__va(BIOS_LOWMEM_KILOBYTES);
:
: If i put lockdep_init() before reserve_ebda_region call in
: x86_64_start_reservations kernel loads well.
Fix this ordering issue permanently: change lockdep so that it uses
hlists for the hash tables. Unlike a list_head, an hlist_head is in its
initialized state when it is all-zeroes, so lockdep is ready for
operation immediately upon boot - lockdep_init() need not have run.
The patch will also save some memory.
lockdep_init() and lockdep_initialized can be done away with now - a 4.6
patch has been prepared to do this.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Suggested-by: Mike Krinkin <krinkin.m.u@gmail.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add all gdsc data which are part of mmcc on msm8996 family
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add all data for the GDSCs which are part of msm8996 GCC block
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
1) Fix BPF handling of branch offset adjustmnets on backjumps, from
Daniel Borkmann.
2) Make sure selinux knows about SOCK_DESTROY netlink messages, from
Lorenzo Colitti.
3) Fix openvswitch tunnel mtu regression, from David Wragg.
4) Fix ICMP handling of TCP sockets in syn_recv state, from Eric
Dumazet.
5) Fix SCTP user hmacid byte ordering bug, from Xin Long.
6) Fix recursive locking in ipv6 addrconf, from Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bpf: fix branch offset adjustment on backjumps after patching ctx expansion
vxlan, gre, geneve: Set a large MTU on ovs-created tunnel devices
geneve: Relax MTU constraints
vxlan: Relax MTU constraints
flow_dissector: Fix unaligned access in __skb_flow_dissector when used by eth_get_headlen
of: of_mdio: Add marvell, 88e1145 to whitelist of PHY compatibilities.
selinux: nlmsgtab: add SOCK_DESTROY to the netlink mapping tables
sctp: translate network order to host order when users get a hmacid
enic: increment devcmd2 result ring in case of timeout
tg3: Fix for tg3 transmit queue 0 timed out when too many gso_segs
net:Add sysctl_max_skb_frags
tcp: do not drop syn_recv on all icmp reports
ipv6: fix a lockdep splat
unix: correctly track in-flight fds in sending process user_struct
update be2net maintainers' email addresses
dwc_eth_qos: Reset hardware before PHY start
ipv6: addrconf: Fix recursive spin lock call
Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The network stack defers SKBs free, in-case free happens in IRQ or
when IRQs are disabled. This happens in __dev_kfree_skb_irq() that
writes SKBs that were free'ed during IRQ to the softirq completion
queue (softnet_data.completion_queue).
These SKBs are naturally delayed, and cleaned up during NET_TX_SOFTIRQ
in function net_tx_action(). Take advantage of this a use the skb
defer and flush API, as we are already in softirq context.
For modern drivers this rarely happens. Although most drivers do call
dev_kfree_skb_any(), which detects the situation and calls
__dev_kfree_skb_irq() when needed. This due to netpoll can call from
IRQ context.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discovered that network stack were hitting the kmem_cache/SLUB
slowpath when freeing SKBs. Doing bulk free with kmem_cache_free_bulk
can speedup this slowpath.
NAPI context is a bit special, lets take advantage of that for bulk
free'ing SKBs.
In NAPI context we are running in softirq, which gives us certain
protection. A softirq can run on several CPUs at once. BUT the
important part is a softirq will never preempt another softirq running
on the same CPU. This gives us the opportunity to access per-cpu
variables in softirq context.
Extend napi_alloc_cache (before only contained page_frag_cache) to be
a struct with a small array based stack for holding SKBs. Introduce a
SKB defer and flush API for accessing this.
Introduce napi_consume_skb() as replacement for e.g. dev_consume_skb_any()
when running in NAPI context. A small trick to handle/detect if we
are called from netpoll is to see if budget is 0. In that case, we
need to invoke dev_consume_skb_irq().
Joint work with Alexander Duyck.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices these days can have any speed and as was recently pointed out
any speed from 0 to INT_MAX is valid so adjust speed validation to
accept such values.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for TPS65912 PMIC MFD core. It provides
communication through the I2C and SPI interfaces. It contains
the following components:
- Regulators
- GPIO controller
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the core driver for imx25 touchscreen/adc driver. The module
has one shared ADC and two different conversion queues which use the
ADC. The two queues are identical. Both can be used for general purpose
ADC but one is meant to be used for touchscreens.
This driver is the core which manages the central components and
registers of the TSC/ADC unit. It manages the IRQs and forwards them to
the correct components.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Denis Carikli <denis@eukrea.com>
[ensure correct ADC clock depending on the IPG clock]
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The documentation describes the bindings for the imx25 GCQ unit which is
essentially a generic conversion queue using the imx25 ADC.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM64 PSCI kernel interfaces that initialize idle states and implement
the suspend API to enter them are generic and can be shared with the
ARM architecture.
To achieve that goal, this patch moves ARM64 PSCI idle management
code to drivers/firmware, so that the interface to initialize and
enter idle states can actually be shared by ARM and ARM64 arches
back-ends.
The ARM generic CPUidle implementation also requires the definition of
a cpuidle_ops section entry for the kernel to initialize the CPUidle
operations at boot based on the enable-method (ie ARM64 has the
statically initialized cpu_ops counterparts for that purpose); therefore
this patch also adds the required section entry on CONFIG_ARM for PSCI so
that the kernel can initialize the PSCI CPUidle back-end when PSCI is
the probed enable-method.
On ARM64 this patch provides no functional change.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arch/arm64]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DMA allocations might be subject to certain requirements specific to the
hardware using the buffers, such as availability of kernel mapping (for
contents fix-ups in the driver). The only entity that knows them is the
driver, so it must share this knowledge with vb2-dc.
This patch extends the alloc_ctx initialization interface to let the
driver specify DMA attrs, which are then stored inside the allocation
context and will be used for all allocations with that context.
As a side effect, all dma_*_coherent() calls are turned into
dma_*_attrs() calls, because the attributes need to be carried over
through all DMA operations.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the DMA_ATTR_ALLOC_SINGLE_PAGES attribute to the
DMA-mapping subsystem.
This attribute can be used as a hint to the DMA-mapping subsystem that
it's likely not worth it to try to allocate large pages behind the
scenes. Large pages are likely to make an IOMMU TLB work more
efficiently but may not be worth it. See the Documentation contained in
this patch for more details about this attribute and when to use it.
Note that the name of the hint (DMA_ATTR_ALLOC_SINGLE_PAGES) is loosely
based on the name MADV_NOHUGEPAGE. Just as there is MADV_NOHUGEPAGE
vs. MADV_HUGEPAGE we could also add an "opposite" attribute to
DMA_ATTR_ALLOC_SINGLE_PAGES. Without having the "opposite" attribute
the lack of DMA_ATTR_ALLOC_SINGLE_PAGES means "use your best judgement
about whether to use small pages or large pages".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.
I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.
The problems with this are:
* On big-endian machines, this will always write a zero because it
stores the wrong byte into user space.
* In compat mode, the upper three bytes of the variable are updated
by the compat_hdio_ioctl() function, but they now contain
uninitialized stack data.
* The hdparm tool calling this ioctl uses a 'static long' variable
to store the result. This means at least the upper bytes are
initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
would fill them with data that remains stale when the low byte
is overwritten. Fortunately libata doesn't implement any of the
affected ioctl commands, so this would only happen when we query
both an IDE and an ATA device in the same command such as
"hdparm -N -c /dev/hda /dev/sda"
* The libata code for unknown reasons started using ATA_IOC_GET_IO32
and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
while the ioctl commands that were added later use the normal
HDIO_* names. This is harmless but rather confusing.
This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
This was initially introduced in df2cf4a78e ("IGMP: Inhibit
reports for local multicast groups") by defining the sysctl in the
ipv4_net_table array, however it was never implemented to be
namespace aware. Fix this by changing the code accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Operations with the GENL_ADMIN_PERM flag fail permissions checks because
this flag means we call netlink_capable, which uses the init user ns.
Instead, let's introduce a new flag, GENL_UNS_ADMIN_PERM for operations
which should be allowed inside a user namespace.
The motivation for this is to be able to run openvswitch in unprivileged
containers. I've tested this and it seems to work, but I really have no
idea about the security consequences of this patch, so thoughts would be
much appreciated.
v2: use the GENL_UNS_ADMIN_PERM flag instead of a check in each function
v3: use separate ifs for UNS_ADMIN_PERM and ADMIN_PERM, instead of one
massive one
Reported-by: James Page <james.page@canonical.com>
Signed-off-by: Tycho Andersen <tycho.andersen@canonical.com>
CC: Eric Biederman <ebiederm@xmission.com>
CC: Pravin Shelar <pshelar@ovn.org>
CC: Justin Pettit <jpettit@nicira.com>
CC: "David S. Miller" <davem@davemloft.net>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many virtual and not quite virtual devices allow any speed to be set
through ethtool. In particular, this applies to the virtio-net devices.
Document this fact to make sure people don't assume the enum lists all
possible values. Reserve values greater than INT_MAX for future
extension and to avoid conflict with SPEED_UNKNOWN.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we can offload the checksums for a packet up
to a certain point and then begin computing the checksums via software.
Setting this up is fairly straight forward as all we need to do is reset
the values stored in csum and csum_start for the GSO context block.
One complication for this is remote checksum offload. In order to allow
the inner checksums to be offloaded while computing the outer checksum
manually we needed to have some way of indicating that the offload wasn't
real. In order to do that I replaced CHECKSUM_PARTIAL with
CHECKSUM_UNNECESSARY in the case of us computing checksums for the outer
header while skipping computing checksums for the inner headers. We clean
up the ip_summed flag and set it to either CHECKSUM_PARTIAL or
CHECKSUM_NONE once we hand the packet off to the next lower level.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the checksum maintained by GSO out of skb->csum and into
the GSO context block in order to allow for us to work on outer checksums
while maintaining the inner checksum offsets in the case of the inner
checksum being offloaded, while the outer checksums will be computed.
While updating the code I also did a minor cleanu-up on gso_make_checksum.
The change is mostly to make it so that we store the values and compute the
checksum instead of computing the checksum and then storing the values we
needed to update.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
