commit f2bc600008 upstream.
When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97618aca14 upstream.
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd3f6983b4 upstream.
SD clock should be disabled for clock value 0. It's not
right to just return. This may cause failure of signal
voltage switching.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c3ada89c upstream.
With CONFIG_KASAN, we get an overly long stack frame due to inlining
the register access functions:
drivers/media/tuners/r820t.c: In function 'generic_set_freq.isra.7':
drivers/media/tuners/r820t.c:1334:1: error: the frame size of 2880 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
This is caused by a gcc bug that has now been fixed in gcc-8.
To work around the problem, we can pass the register data
through a local variable that older gcc versions can optimize
out as well.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05e89fb576 upstream.
It is no longer possible to build BT_HCIUART into the kernel
when SERIAL_DEV_BUS is a loadable module, even if none of the
SERIAL_DEV_BUS based implementations are selected:
drivers/bluetooth/hci_ldisc.o: In function `hci_uart_set_flow_control':
hci_ldisc.c:(.text+0xb40): undefined reference to `serdev_device_set_flow_control'
hci_ldisc.c:(.text+0xb5c): undefined reference to `serdev_device_set_tiocm'
This adds a dependency to avoid the broken configuration.
Fixes: 7841d55480 ("Bluetooth: hci_uart_set_flow_control: Fix NULL deref when using serdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81b6c99989 upstream.
As it turned out device_get() doesn't use kref_get_unless_zero(), so we
will be always getting a device pointer. Consequently, we need to check
for the device state in __scsi_remove_target() to avoid tripping over
deleted objects.
Fixes: fbce4d97fd ("scsi: fixup kernel warning during rmmod()")
Reported-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Max Ivanov <ivanov.maxim@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec897569ad upstream.
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ac8ff95f4 upstream.
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea56fb2823 upstream.
With commit 3cf32d1802 ("mtd: nand: vf610: switch to
mtd_ooblayout_ops") the driver started to use the NAND cores
default large page ooblayout. However, shortly after commit
6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
changed the default layout to the old hamming layout, which is
not what vf610_nfc is using. Specify the default large page
layout explicitly.
Fixes: 6a623e0769 ("mtd: nand: add ooblayout for old hamming layout")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dd601fa83 upstream.
dec_pending() is given an error status (possibly 0) to be recorded
against a bio. It can be called several times on the one 'struct
dm_io', and it is careful to only assign a non-zero error to
io->status. However when it then assigned io->status to bio->bi_status,
it is not careful and could overwrite a genuine error status with 0.
This can happen when chained bios are in use. If a bio is chained
beneath the bio that this dm_io is handling, the child bio might
complete and set bio->bi_status before the dm_io completes.
This has been possible since chained bios were introduced in 3.14, and
has become a lot easier to trigger with commit 18a25da843 ("dm: ensure
bio submission follows a depth-first tree walk") as that commit caused
dm to start using chained bios itself.
A particular failure mode is that if a bio spans an 'error' target and a
working target, the 'error' fragment will complete instantly and set the
->bi_status, and the other fragment will normally complete a little
later, and will clear ->bi_status.
The fix is simply to only assign io_error to bio->bi_status when
io_error is not zero.
Reported-and-tested-by: Milan Broz <gmazyland@gmail.com>
Cc: stable@vger.kernel.org (v3.14+)
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c130ae00b upstream.
Mike Christie reports:
Starting in 4.14 iscsi logins will fail around 50% of the time.
Problem appears to be that iscsi_target_sk_data_ready() callback may
return without doing anything in case it finds the login work queue
is still blocked in sock_recvmsg().
Nicholas Bellinger says:
It would indicate users providing their own ->sk_data_ready() callback
must be responsible for waking up a kthread context blocked on
sock_recvmsg(..., MSG_WAITALL), when a second ->sk_data_ready() is
received before the first sock_recvmsg(..., MSG_WAITALL) completes.
So, do this and invoke the original data_ready() callback -- in
case of tcp sockets this takes care of waking the thread.
Disclaimer: I do not understand why this problem did not show up before
tcp prequeue removal.
(Drop WARN_ON usage - nab)
Reported-by: Mike Christie <mchristi@redhat.com>
Bisected-by: Mike Christie <mchristi@redhat.com>
Tested-by: Mike Christie <mchristi@redhat.com>
Diagnosed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fixes: e7942d0633 ("tcp: remove prequeue support")
Signed-off-by: Florian Westphal <fw@strlen.de>
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce512d79d0 upstream.
If chap_server_compute_md5() fails early, e.g. via CHAP_N mismatch, then
crypto_free_shash() is called with a NULL pointer which gets
dereferenced in crypto_shash_tfm().
Fixes: 69110e3ced ("iscsi-target: Use shash and ahash")
Suggested-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Cc: stable@vger.kernel.org # 4.6+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9428088c90 upstream.
QXL associates mouse state with its primary plane.
Destroying a primary plane and putting a new one in place has the side
effect of destroying the cursor as well.
This commit changes the driver to reapply the cursor any time a new
primary is created. It achieves this by keeping a reference to the
cursor bo on the qxl_crtc struct.
This fix is very similar to
commit 4532b241a4 ("drm/qxl: reapply cursor after SetCrtc calls")
which got implicitly reverted as part of implementing the atomic
modeset feature.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1512097
Fixes: 1277eed5fe ("drm: qxl: Atomic phase 1: convert cursor to universal plane")
Cc: stable@vger.kernel.org
Signed-off-by: Ray Strode <rstrode@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 62676d10b4 upstream.
This patch changes the way the primary surface is used for dumb
framebuffers. Instead of configuring the bo itself as primary surface
a shadow bo is created and used instead. Framebuffers can share the
shadow bo in case they have the same format and resolution.
On atomic plane updates we don't have to update the primary surface in
case we pageflip from one framebuffer to another framebuffer which
shares the same shadow. This in turn avoids the flicker caused by the
primary-destroy + primary-create cycle, which is very annonying when
running wayland on qxl.
The qxl driver never actually writes to the shadow bo. It sends qxl
blit commands which update it though, and the spice server might
actually execute them (and thereby write to the shadow) in case the
local rendering is kicked for some reason. This happens for example in
case qemu is asked to write out a dump of the guest display (screendump
monitor command).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20171019062150.28090-3-kraxel@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c713fb071e upstream.
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29fee6eed2 upstream.
Commit fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent
xenstore accesses") optimized xenbus concurrent accesses but in doing so
broke UABI of /dev/xen/xenbus. Through /dev/xen/xenbus applications are in
charge of xenbus message exchange with the correct header and body. Now,
after the mentioned commit the replies received by application will no
longer have the header req_id echoed back as it was on request (see
specification below for reference), because that particular field is being
overwritten by kernel.
struct xsd_sockmsg
{
uint32_t type; /* XS_??? */
uint32_t req_id;/* Request identifier, echoed in daemon's response. */
uint32_t tx_id; /* Transaction id (0 if not related to a transaction). */
uint32_t len; /* Length of data following this. */
/* Generally followed by nul-terminated string(s). */
};
Before there was only one request at a time so req_id could simply be
forwarded back and forth. To allow simultaneous requests we need a
different req_id for each message thus kernel keeps a monotonic increasing
counter for this field and is written on every request irrespective of
userspace value.
Forwarding again the req_id on userspace requests is not a solution because
we would open the possibility of userspace-generated req_id colliding with
kernel ones. So this patch instead takes another route which is to
artificially keep user req_id while keeping the xenbus logic as is. We do
that by saving the original req_id before xs_send(), use the private kernel
counter as req_id and then once reply comes and was validated, we restore
back the original req_id.
Cc: <stable@vger.kernel.org> # 4.11
Fixes: fd8aa9095a ("xen: optimize xenbus driver for multiple concurrent xenstore accesses")
Reported-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e573427a44 upstream.
This feature bit restricts older clients from performing certain
maintenance operations against an image (e.g. clone, snap create).
krbd does not perform maintenance operations.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 724ba8b30b upstream.
When this method is set, the caller expects struct console_font fields
to be properly initialized when it returns. Leave it unset otherwise
nonsensical (leaked kernel stack) values are returned to user space.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cb18db070 upstream.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent display node was also prematurely
freed.
Note that the display and timings node references are never put after a
successful dt-initialisation so the nodes would leak on later probe
deferrals and on driver unbind.
Fixes: b985172b32 ("video: atmel_lcdfb: add device tree suport")
Cc: stable <stable@vger.kernel.org> # 3.13
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eac56aa3bc upstream.
Fix child-node lookup during initialisation which was using the wrong
OF-helper and ended up searching the whole device tree depth-first
starting at the parent rather than just matching on its children.
To make things worse, the parent pci node could end up being prematurely
freed as of_find_node_by_name() drops a reference to its first argument.
Any matching child interrupt-controller node was also leaked.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Cc: stable <stable@vger.kernel.org> # 3.18
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
[lorenzo.pieralisi@arm.com: updated commit subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b65ca50d2 upstream.
With the inbound DMA mapping supported added, the iProc PCIe driver
parses DT property "dma-ranges" through call to
"of_pci_dma_range_parser_init()". In the case of BCMA, this results in a
NULL pointer deference due to a missing of_node.
Fix this by adding a guard in pcie-iproc-platform.c to only enable the
inbound DMA mapping logic when DT property "dma-ranges" is present.
Fixes: dd9d4e7498 ("PCI: iproc: Add inbound DMA mapping support")
Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deb8699932 upstream.
HiSilicon Hip06/Hip07 can operate as either a Root Port or an Endpoint. It
always advertises an MSI capability, but it can only generate MSIs when in
Endpoint mode.
The device has the same Vendor and Device IDs in both modes, so check the
Class Code and disable MSI only when operating as a Root Port.
[bhelgaas: changelog]
Fixes: 72f2ff0deb ("PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6fa7588fd upstream.
Commit 4eebd5a4e7 ("apple-gmux: lock iGP IO to protect from vgaarb
changes") amended this driver's ->probe hook to lock decoding of normal
(non-legacy) I/O space accesses to the integrated GPU on dual-GPU
MacBook Pros. The lock stays in place until the driver is unbound.
The change was made to work around an issue with the out-of-tree nvidia
graphics driver (available at http://www.nvidia.com/object/unix.html).
It contains the following sequence in nvidia/nv.c:
#if defined(CONFIG_VGA_ARB) && !defined(NVCPU_PPC64LE)
#if defined(VGA_DEFAULT_DEVICE)
vga_tryget(VGA_DEFAULT_DEVICE, VGA_RSRC_LEGACY_MASK);
#endif
vga_set_legacy_decoding(dev, VGA_RSRC_NONE);
#endif
This code was reported to cause deadlocks with VFIO already in 2013:
https://devtalk.nvidia.com/default/topic/545560
I've reported the issue to Nvidia developers once more in 2017:
https://www.spinics.net/lists/dri-devel/msg138754.html
On the MacBookPro10,1, this code apparently breaks backlight control
(which is handled by apple-gmux via an I/O region starting at 0x700),
as reported by Petri Hodju:
https://bugzilla.kernel.org/show_bug.cgi?id=86121
I tried to replicate Petri's observations on my MacBook9,1, which uses
the same Intel Ivy Bridge + Nvidia GeForce GT 650M architecture, to no
avail. On my machine apple-gmux' I/O region remains accessible even
with the nvidia driver loaded and commit 4eebd5a4e7 reverted.
Petri reported that apple-gmux becomes accessible again after a
suspend/resume cycle because the BIOS changed the VGA routing on the
root port to the Nvidia GPU. Perhaps this is a BIOS issue after all
that can be fixed with an update?
In any case, the change made by commit 4eebd5a4e7 has turned out to
cause two new issues:
* Wilfried Klaebe reports a deadlock when launching Xorg because it
opens /dev/vga_arbiter and calls vga_get(), but apple-gmux is holding
a lock on I/O space indefinitely. It looks like apple-gmux' current
behavior is an abuse of the vgaarb API as locks are not meant to be
held for longer periods:
https://bugzilla.kernel.org/show_bug.cgi?id=88861#c11https://bugzilla.kernel.org/attachment.cgi?id=217541
* On dual GPU MacBook Pros introduced since 2013, the integrated GPU is
powergated on boot und thus becomes invisible to Linux unless a custom
EFI protocol is used to leave it powered on. (A patch exists but is
not in mainline yet due to several negative side effects.) On these
machines, locking I/O to the integrated GPU (as done by 4eebd5a4e7)
fails and backlight control is therefore broken:
https://bugzilla.kernel.org/show_bug.cgi?id=105051
So let's revert commit 4eebd5a4e7 please. Users experiencing the
issue with the proprietary nvidia driver can comment out the above-
quoted problematic code as a workaround (or try updating the BIOS).
Cc: Petri Hodju <petrihodju@yahoo.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Andy Ritger <aritger@nvidia.com>
Cc: Ronald Tschalär <ronald@innovation.ch>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe0e58048f upstream.
This reverts commit 0a44697627.
This commit was initially intended to fix problems with hs200 and hs400
on some boards, mainly the odroid-c2. The OC2 (Rev 0.2) I have performs
well in this modes, so I could not confirm these issues.
We've had several reports about the issues being still present on (some)
OC2, so apparently, this change does not do what it was supposed to do.
Maybe the eMMC signal quality is on the edge on the board. This may
explain the variability we see in term of stability, but this is just a
guess. Lowering the max_frequency to 100Mhz seems to do trick for those
affected by the issue
Worse, the commit created new issues (CRC errors and hangs) on other
boards, such as the kvim 1 and 2, the p200 or the libretech-cc.
According to amlogic, the Tx phase should not be tuned and left in its
default configuration, so it is best to just revert the commit.
Fixes: 0a44697627 ("mmc: meson-gx: include tx phase in the tuning process")
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 118032be38 upstream.
The optional DT parameter max-frequency could init the max bus frequency.
So take care of this, before setting the max bus frequency.
Fixes: 660fc733bd ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd9b902798 upstream.
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.
SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.
Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.
These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.
This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.
When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.
dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA
On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b8b580630 upstream.
According to the OPAL docs:
skiboot-5.2.5/doc/opal-api/opal-rtc-read-3.txt
skiboot-5.2.5/doc/opal-api/opal-rtc-write-4.txt
OPAL_HARDWARE may be returned from OPAL_RTC_READ or OPAL_RTC_WRITE and
this indicates either a transient or permanent error.
Prior to this patch, Linux was not dealing with OPAL_HARDWARE being a
permanent error particularly well, in that you could end up in a busy
loop.
This was not too hard to trigger on an AMI BMC based OpenPOWER machine
doing a continuous "ipmitool mc reset cold" to the BMC, the result of
that being that we'd get stuck in an infinite loop in
opal_get_rtc_time().
We now retry a few times before returning the error higher up the
stack.
Fixes: 16b1d26e77 ("rtc/tpo: Driver to support rtc and wakeup on PowerNV platform")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a61b527b4 upstream.
Check the variable that was most recently initialized.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x, y, f, g, e, m;
statement S1,S2,S3,S4;
@@
x = f(...);
if (\(<+...x...+>\&e\)) S1 else S2
(
x = g(...);
|
m = g(...,&x,...);
|
y = g(...);
*if (e)
S3 else S4
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 24b8ef699e upstream.
In the past the ast driver relied upon the fbdev emulation helpers to
call ->load_lut at boot-up. But since
commit b8e2b0199c
Author: Peter Rosin <peda@axentia.se>
Date: Tue Jul 4 12:36:57 2017 +0200
drm/fb-helper: factor out pseudo-palette
that's cleaned up and drivers are expected to boot into a consistent
lut state. This patch fixes that.
Fixes: b8e2b0199c ("drm/fb-helper: factor out pseudo-palette")
Cc: Peter Rosin <peda@axenita.se>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198123
Cc: Bill Fraser <bill.fraser@gmail.com>
Reported-and-Tested-by: Bill Fraser <bill.fraser@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit adab595d16 upstream.
The handle describes kernel logical address, should be
unsigned long and not uint32_t.
Fixes KASAN error and GFP on driver unload.
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16c6db3688 upstream.
qxl_cursor_atomic_update allocs a bo for the cursor that
it never frees up at the end of the function.
This commit fixes that.
Signed-off-by: Ray Strode <rstrode@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95244db2d3 upstream.
The buf pointer was not being incremented inside the loop
meaning the same block of data would be read or written
repeatedly.
(v2) Change 'buf' pointer to uint8_t* type
Cc: stable@vger.kernel.org
Fixes: 09ac4fcb3f ("drm/ttm: Implement vm_operations_struct.access v2")
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd5002d6a3 upstream.
A BO that's already swapped would be added back to the swap-LRU list
for example if its validation failed under high memory pressure. This
could later lead to swapping it out again and leaking previous swap
storage.
This commit adds a condition to prevent that from happening.
v2: Check page_flags instead of swap_storage
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b399151cb4 upstream.
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4950276672 upstream.
Patch series "kmemcheck: kill kmemcheck", v2.
As discussed at LSF/MM, kill kmemcheck.
KASan is a replacement that is able to work without the limitation of
kmemcheck (single CPU, slow). KASan is already upstream.
We are also not aware of any users of kmemcheck (or users who don't
consider KASan as a suitable replacement).
The only objection was that since KASAN wasn't supported by all GCC
versions provided by distros at that time we should hold off for 2
years, and try again.
Now that 2 years have passed, and all distros provide gcc that supports
KASAN, kill kmemcheck again for the very same reasons.
This patch (of 4):
Remove kmemcheck annotations, and calls to kmemcheck from the kernel.
[alexander.levin@verizon.com: correctly remove kmemcheck call from dma_map_sg_attrs]
Link: http://lkml.kernel.org/r/20171012192151.26531-1-alexander.levin@verizon.com
Link: http://lkml.kernel.org/r/20171007030159.22241-2-alexander.levin@verizon.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Hansen <devtimhansen@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 433986c2c2 upstream.
Commit baa8809f60 (PM / runtime: Optimize the use of device links)
added an invocation of pm_runtime_drop_link() to __device_link_del().
However there are two variants of that function, one for CONFIG_SRCU and
another for !CONFIG_SRCU, and the commit only modified the former.
Fixes: baa8809f60 (PM / runtime: Optimize the use of device links)
Cc: v4.10+ <stable@vger.kernel.org> # v4.10+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e7d1d61ea upstream.
Lockdep detects a possible deadlock in sun4i_ss_prng_generate() and
throws an "inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage" warning.
Disabling softirqs to fix this.
Fixes: b8ae5c7387 ("crypto: sun4i-ss - support the Security System PRNG")
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd78c832ff upstream.
According to crypto/rng.h generate function should return 0 on success
and < 0 on error.
Fixes: b8ae5c7387 ("crypto: sun4i-ss - support the Security System PRNG")
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0890540e21 upstream.
Up to Coffeelake we could deduce this GT number from the device ID.
This doesn't seem to be the case anymore. This change reorders pciids
per GT and adds a gt field to intel_device_info. We set this field on
the following platforms :
- SNB/IVB/HSW/BDW/SKL/KBL/CFL/CNL
Before & After :
$ modinfo drivers/gpu/drm/i915/i915.ko | grep ^alias | wc -l
209
v2: Add SNB & IVB (Chris)
v3: Fix compilation error in early-quirks (Lionel)
v4: Fix inconsistency between FEATURE/PLATFORM macros (Ville)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170830161208.29221-2-lionel.g.landwerlin@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bffee867d upstream.
We need to set shared_count even if we already have a fence to wait for.
v2: init i to -1 as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122200003.6665-1-christian.koenig@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a64e7a79dd upstream.
Commit b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1bf2d3072 upstream.
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d3 ("PM / devfreq: Add resource-managed function for devfreq device")
Cc: stable@vger.kernel.org
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fa4680b86 upstream.
Some OpenPOWER boxes can have same pstate values for nominal and
pmin pstates. In these boxes the current code will not initialize
'powernv_pstate_info.min' variable and result in erroneous CPU
frequency reporting. This patch fixes this problem.
Fixes: 09ca4c9b59 (cpufreq: powernv: Replacing pstate_id with frequency table index)
Reported-by: Alvin Wang <wangat@tw.ibm.com>
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb3ffb7ad4 upstream.
rxe_qp_cleanup() can sleep so it must be run in thread context and
not in atomic context. This patch avoids that the following bug is
triggered:
Kernel BUG at 00000000560033f3 [verbose debug info unavailable]
BUG: sleeping function called from invalid context at net/core/sock.c:2761
in_atomic(): 1, irqs_disabled(): 0, pid: 7, name: ksoftirqd/0
INFO: lockdep is turned off.
Preemption disabled at:
[<00000000b6e69628>] __do_softirq+0x4e/0x540
CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 4.15.0-rc7-dbg+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
Call Trace:
dump_stack+0x85/0xbf
___might_sleep+0x177/0x260
lock_sock_nested+0x1d/0x90
inet_shutdown+0x2e/0xd0
rxe_qp_cleanup+0x107/0x140 [rdma_rxe]
rxe_elem_release+0x18/0x80 [rdma_rxe]
rxe_requester+0x1cf/0x11b0 [rdma_rxe]
rxe_do_task+0x78/0xf0 [rdma_rxe]
tasklet_action+0x99/0x270
__do_softirq+0xc0/0x540
run_ksoftirqd+0x1c/0x70
smpboot_thread_fn+0x1be/0x270
kthread+0x117/0x130
ret_from_fork+0x24/0x30
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65567e4121 upstream.
The rxe driver works as follows:
* The send queue, receive queue and completion queues are implemented as
circular buffers.
* ib_post_send() and ib_post_recv() calls are serialized through a spinlock.
* Removing elements from various queues happens from tasklet
context. Tasklets are guaranteed to run on at most one CPU. This serializes
access to these queues. See also rxe_completer(), rxe_requester() and
rxe_responder().
* rxe_completer() processes the skbs queued onto qp->resp_pkts.
* rxe_requester() handles the send queue (qp->sq.queue).
* rxe_responder() processes the skbs queued onto qp->req_pkts.
Since rxe_drain_req_pkts() processes qp->req_pkts, calling
rxe_drain_req_pkts() from rxe_requester() is racy. Hence this patch.
Reported-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f301e06de upstream.
The following sequence:
* Change queue pair state into IB_QPS_ERR.
* Post a work request on the queue pair.
Triggers the following race condition in the rdma_rxe driver:
* rxe_qp_error() triggers an asynchronous call of rxe_completer(), the function
that examines the QP send queue.
* rxe_post_send() posts a work request on the QP send queue.
If rxe_completer() runs prior to rxe_post_send(), it will drain the send
queue and the driver will assume no further action is necessary.
However, once we post the send to the send queue, because the queue is
in error, no send completion will ever happen and the send will get
stuck. In order to process the send, we need to make sure that
rxe_completer() gets run after a send is posted to a queue pair in an
error state. This patch ensures that happens.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Moni Shoua <monis@mellanox.com>
Cc: <stable@vger.kernel.org> # v4.8
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ff124d597 upstream.
The ev_file is an optional parameter for CQ creation. If the parameter
is not passed, the ev_file pointer will be NULL. Using that pointer
to set the cq_context will result in an OOPs.
Verify that ev_file is not NULL before using.
Cc: <stable@vger.kernel.org> # 4.14.x
Fixes: 9ee79fce36 ("IB/core: Add completion queue (cq) object actions")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 852f692759 upstream.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be7 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
