commit 852f692759 upstream.
Allocating steerable UD QPs depends on having at least one IB port,
while releasing those QPs does not.
As a result, when there are only ETH ports, the IB (RoCE) driver
requests releasing a qp range whose base qp is zero, with
qp count zero.
When SR-IOV is enabled, and the VF driver is running on a VM over
a hypervisor which treats such qp release calls as errors
(rather than NOPs), we see lines in the VM message log like:
mlx4_core 0002:00:02.0: Failed to release qp range base:0 cnt:0
Fix this by adding a check for a zero count in mlx4_release_qp_range()
(which thus treats releasing 0 qps as a nop), and eliminating the
check for device managed flow steering when releasing steerable UD QPs.
(Freeing ib_uc_qpns_bitmap unconditionally is also OK, since it
remains NULL when steerable UD QPs are not allocated).
Fixes: 4196670be7 ("IB/mlx4: Don't allocate range of steerable UD QPs for Ethernet-only device")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87b3524cb5 upstream.
This failure exists with qib:
ver_rc_compare_swap:
mismatch, sequence 2, expected 123456789abcdef, got 0
The request builder was using the incorrect inlines to
build the request header resulting in incorrect data
in the atomic header.
Fix by using the appropriate inlines to create the request.
Fixes: 261a435184 ("IB/qib,IB/hfi: Use core common header file")
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8978cc921f ]
There are systems platform information management interfaces (such as
HOST2BMC) for which we cannot disable local loopback multicast traffic.
Separate disable_local_lb_mc and disable_local_lb_uc capability bits so
driver will not disable multicast loopback traffic if not supported.
(It is expected that Firmware will not set disable_local_lb_mc if
HOST2BMC is running for example.)
Function mlx5_nic_vport_update_local_lb will do best effort to
disable/enable UC/MC loopback traffic and return success only in case it
succeeded to changed all allowed by Firmware.
Adapt mlx5_ib and mlx5e to support the new cap bits.
Fixes: 2c43c5a036 ("net/mlx5e: Enable local loopback in loopback selftest")
Fixes: c85023e153 ("IB/mlx5: Add raw ethernet local loopback support")
Fixes: bded747bb4 ("net/mlx5: Add raw ethernet local loopback firmware command")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ae59c3f0b6 upstream.
The rdma_ah_find_type() accesses the port array based on an index
controlled by userspace. The existing bounds check is after the first use
of the index, so userspace can generate an out of bounds access, as shown
by the KASN report below.
==================================================================
BUG: KASAN: slab-out-of-bounds in to_rdma_ah_attr+0xa8/0x3b0
Read of size 4 at addr ffff880019ae2268 by task ibv_rc_pingpong/409
CPU: 0 PID: 409 Comm: ibv_rc_pingpong Not tainted 4.15.0-rc2-00031-gb60a3faf5b83-dirty #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0xe9/0x18f
print_address_description+0xa2/0x350
kasan_report+0x3a5/0x400
to_rdma_ah_attr+0xa8/0x3b0
mlx5_ib_query_qp+0xd35/0x1330
ib_query_qp+0x8a/0xb0
ib_uverbs_query_qp+0x237/0x7f0
ib_uverbs_write+0x617/0xd80
__vfs_write+0xf7/0x500
vfs_write+0x149/0x310
SyS_write+0xca/0x190
entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x7fe9c7a275a0
RSP: 002b:00007ffee5498738 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007fe9c7ce4b00 RCX: 00007fe9c7a275a0
RDX: 0000000000000018 RSI: 00007ffee5498800 RDI: 0000000000000003
RBP: 000055d0c8d3f010 R08: 00007ffee5498800 R09: 0000000000000018
R10: 00000000000000ba R11: 0000000000000246 R12: 0000000000008000
R13: 0000000000004fb0 R14: 000055d0c8d3f050 R15: 00007ffee5498560
Allocated by task 1:
__kmalloc+0x3f9/0x430
alloc_mad_private+0x25/0x50
ib_mad_post_receive_mads+0x204/0xa60
ib_mad_init_device+0xa59/0x1020
ib_register_device+0x83a/0xbc0
mlx5_ib_add+0x50e/0x5c0
mlx5_add_device+0x142/0x410
mlx5_register_interface+0x18f/0x210
mlx5_ib_init+0x56/0x63
do_one_initcall+0x15b/0x270
kernel_init_freeable+0x2d8/0x3d0
kernel_init+0x14/0x190
ret_from_fork+0x24/0x30
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff880019ae2000
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 104 bytes to the right of
512-byte region [ffff880019ae2000, ffff880019ae2200)
The buggy address belongs to the page:
page:000000005d674e18 count:1 mapcount:0 mapping: (null) index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 00000001000c000c
raw: dead000000000100 dead000000000200 ffff88001a402000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff880019ae2100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2180: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
>ffff880019ae2200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff880019ae2280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Disabling lock debugging due to kernel taint
Fixes: 44c58487d5 ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 57194fa763 upstream.
In the original code, we set "fd->uctxt" to NULL and then dereference it
which will cause an Oops.
Fixes: f2a3bc00a0 ("IB/hfi1: Protect context array set/clear with spinlock")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d145873345 upstream.
If a wr chain was posted and needed to be flushed, only the first
wr in the chain was completed with FLUSHED status. The rest were
never completed. This caused isert to hang on shutdown due to the
missing completions which left iscsi IO commands referenced, stalling
the shutdown.
Fixes: 4fe7c2962e ("iw_cxgb4: refactor sq/rq drain logic")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96a236ed28 upstream.
The flush/drain logic was not retaining the original wr opcode in
its completion. This can cause problems if the application uses
the completion opcode to make decisions.
Use bit 10 of the CQE header word to indicate the CQE is a special
drain completion, and save the original WR opcode in the cqe header
opcode field.
Fixes: 4fe7c2962e ("iw_cxgb4: refactor sq/rq drain logic")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 335ebf6fa3 upstream.
In __flush_qp(), the CQ ARMED bit was being cleared regardless of
whether any notification is actually needed. This resulted in the iser
termination logic getting stuck in ib_drain_sq() because the CQ was not
marked ARMED and thus the drain CQE notification wasn't triggered.
This new bug was exposed when this commit was merged:
commit cbb40fadd3 ("iw_cxgb4: only call the cq comp_handler when the
cq is armed")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc52e9ca74 upstream.
__flush_qp() has a race condition where during the flush operation,
the qp lock is released allowing another thread to possibly post a WR,
which corrupts the queue state, possibly causing crashes. The lock was
released to preserve the cq/qp locking hierarchy of cq first, then qp.
However releasing the qp lock is not necessary; both RQ and SQ CQ locks
can be acquired first, followed by the qp lock, and then the RQ and SQ
flushing can be done w/o unlocking.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbb40fadd3 upstream.
The ULPs completion handler should only be called if the CQ is
armed for notification.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad9a3668a4 upstream.
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Fixes: 7c2344c3bb ("IB/mlx5: Implements disassociate_ucontext API")
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c009af473 upstream.
During driver init, various registers are saved to allow restoration
after an FLR or gen3 bump. Some of these registers are not available
in some circumstances (i.e. Virtual machines).
This bug makes the driver unusable when the PCI device is passed into
a VM, it fails during probe.
Delete unnecessary register read/write, and only access register if
the capability exists.
Fixes: a618b7e40a ("IB/hfi1: Move saving PCI values to a separate function")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f55688c454 upstream.
If the RECV CQE is in error, ignore the MSN check. This was causing
recvs that were flushed into the sw cq to be completed with the wrong
status (BAD_MSN instead of FLUSHED).
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e437b1d7e ]
After the loop in hns_roce_v1_mr_free_work_fn function, it is possible that
all qps will have been freed (in which case ne will be 0). If that
happens, then later in the function when we dereference hr_qp we will
get an exception. Check ne is not 0 to make sure we actually have an
hr_qp left to work on.
This patch fixes the smatch error as below:
drivers/infiniband/hw/hns/hns_roce_hw_v1.c:1009 hns_roce_v1_mr_free_work_fn()
error: we previously assumed 'hr_qp' could be null
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Shaobo Xu <xushaobo2@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0a2f45471 ]
The trace logic prior to the fixes below used to mask the
A bit from the psn. It now mistakenly displays the A bit,
which is already displayed separately.
Fix by adding the appropriate mask to the psn tracing.
Fixes: 228d2af1b7 ("IB/hfi1: Separate input/output header tracing")
Fixes: 863cf89d47 ("IB/hfi1: Add 16B trace support")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00f9203119 ]
__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Patel Jay P <jay.p.patel@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 108809a057 ]
In the modify QP handler the base_qpn_udp field in the RSS QPC is
overwrite later by irrelevant value assignment. Hence, ingress packets
which gets to the RSS QP will be steered then to a garbage QPN.
The patch fixes this by skipping the above assignment when a RSS QP is
modified, also, the RSS context's attributes assignments are relocated
just before the context is posted to avoid future issues like this.
Additionally, this patch takes the opportunity to change the code to be
disciplined to the device's manual and assigns the RSS QP context just at
RESET to INIT transition.
Fixes:3078f5f1bd8b ("IB/mlx4: Add support for RSS QP")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c058ecf6e4 upstream.
Only insert our special drain CQEs to support ib_drain_sq/rq() after
the wq is flushed. Otherwise, existing but not yet polled CQEs can be
returned out of order to the user application. This can happen when the
QP has exited RTS but not yet flushed the QP, which can happen during
a normal close (vs abortive close).
In addition never count the drain CQEs when determining how many CQEs
need to be synthesized during the flush operation. This latter issue
should never happen if the QP is properly flushed before inserting the
drain CQE, but I wanted to avoid corrupting the CQ state. So we handle
it and log a warning once.
Fixes: 4fe7c2962e ("iw_cxgb4: refactor sq/rq drain logic")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7d7d065a5e ]
Chelsio cxgb4 HW is big-endian, hence there is need to properly
annotate r2 and stag fields as __be32 and not __u32 to fix the
following sparse warnings.
drivers/infiniband/hw/cxgb4/qp.c:614:16:
warning: incorrect type in assignment (different base types)
expected unsigned int [unsigned] [usertype] r2
got restricted __be32 [usertype] <noident>
drivers/infiniband/hw/cxgb4/qp.c:615:18:
warning: incorrect type in assignment (different base types)
expected unsigned int [unsigned] [usertype] stag
got restricted __be32 [usertype] <noident>
Cc: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31fde034a8 ]
The UMR's QP is created by calling mlx5_ib_create_qp directly, and
therefore the send CQ and the recv CQ on the ibqp weren't assigned.
Assign them right after calling the mlx5_ib_create_qp to assure
that any access to those pointers will work as expected and won't
crash the system as might happen as part of reset flow.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f22a1d87c ]
Maximal message should be used as a limit to the max message payload allowed,
without the headers. The ConnectX-3 check is done against this value includes
the headers. When the payload is 4K this will cause the NIC to drop packets.
Increase maximal message to 8K as workaround, this shouldn't change current
behaviour because we continue to set the MTU to 4k.
To reproduce;
set MTU to 4296 on the corresponding interface, for example:
ifconfig eth0 mtu 4296 (both server and client)
On server:
ib_send_bw -c UD -d mlx4_0 -s 4096 -n 1000000 -i1 -m 4096
On client:
ib_send_bw -d mlx4_0 -c UD <server_ip> -s 4096 -n 1000000 -i 1 -m 4096
Fixes: 6e0d733d92 ("IB/mlx4: Allow 4K messages for UD QPs")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 063fb5bd1a ]
While adding a new gid, the driver currently does not return the context
back to the stack. A subsequent del_gid() (e.g, when ip address is changed)
doesn't find the right context in the driver and it ends up dropping that
request. This results in the HW caching a stale gid entry and traffic fails
because of that. Fix by returning the proper context in bnxt_re_add_gid().
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7d626179f upstream.
The addition of the VNIC contexts to num_rcv_contexts changes the
meaning of the sysfs value nctxts from available user contexts, to
user contexts + reserved VNIC contexts.
User applications that use nctxts are now broken.
Update the calculation so that VNIC contexts are used only if there are
hardware contexts available, and do not silently affect nctxts.
Update code to use the calculated VNIC context number.
Update the sysfs value nctxts to be available user contexts only.
Fixes: 2280740f01 ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Niranjana Vishwanathapura <Niranjana.Vishwanathapura@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port number 0 is an invalid port number. Set it to 1
as there is one port per i40iw device.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove duplicate set_64bit_val call to offset 24.
Replace some instances of set_64bit_val with
i40iw_insert_wqe_hdr as valid bit needs a write
barrier and should be the last write operation for the WQE.
Fixes: 786c6adb3a ("i40iw: add puda code")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Parse the vlan priority from the vlan tag and configure it to the
WC's sl field.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Rename vlan_id field name to vlan as it contains more than the vlan_id.
Mask out non vlan id fields from vlan tag of the QED LL2 RX GSI
vlan output. As it is expected to be vlan id only.
Ignore vlan_id with value of zero.
Fixes: abd49676c7 ("qed: Add RoCE ll2 & GSI support")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When UAR get_page fails, it needs to continue to cleanup debugfs for
congestion control parameters. Labels for error path were incorrectly
ordered.
This patch fixes to do correct cleanup on debugfs init failure and uar
get page failure.
Fixes: 4a2da0b8c0 ("IB/mlx5: Add debug control parameters for congestion control")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Failure to tune PCIe capabilities should not fail driver load. This can
cause the driver load to fail on systems with any of the following:
1. HFI's parent is not root. Example: HFI card is behind a PCIe bridge.
2. HFI's parent is not PCI Express capable.
In these situations, failure to tune PCIe capabilities should be logged
in the system message logs but not cause the driver load to fail.
This patch also ensures pcie capability word DevCtl is written only
after a successful read and the capability tuning process continues
even if read/write of the pcie capability word DevCtl fails.
Fixes: c53df62c7a ("IB/hfi1: Check return values from PCI config API calls")
Fixes: bf70a77577 ("staging/rdma/hfi1: Enable WFR PCIe extended tags from the driver")
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
During base context setup, if setup_base_ctxt() fails, the context is
deallocated. This is incorrect because the context is referenced on
return, to notify any waiting subcontext. If there are no subcontexts
the pointer will be invalid.
Reorganize the error path so that deallocate_ctxt() is called after all
the possible subcontexts have been notified.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The general interrupt handler returns IRQ_HANDLED whether an IRQ
was handled or not.
Determine if an IRQ was handled and return the correct value.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Relying on a trailing magic value is incorrect. There are instances where
this is not present as trailing magic value has a specific purpose which is
not partition validation. Instead use the header magic value which is
present in all variants of the platform configuration and is intended for
validation. This is also used in other locations in the driver.
Fixes: bc5214ee29 (IB/hfi1: Handle missing magic values in config file)
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
QSFP reset enables AOC transmitters by default. They should be off
before moving to high power mode to complete the setup. There is no
need to reset the QSFP during LNI failure as it was reset at link down.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Offline.quietDuration was added in the 8051 firmware, and the driver
only turns off the AOC transmitters when offline.quiet is reached.
However, the AOC transmitters need to be turned off at the new state.
Therefore, turn off the AOC transmitters at any offline substates
including offline.quiet and offline.quietDuration, then recheck we
reached offline.quiet to support backwards compatibility.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
mlx5_ib_reg_user_mr called mlx5_ib_dereg_mr in case of MR population
failure. This resulted in a NULL dereference as ibmr->device wasn't
initialized yet.
We address this by adding an internal dereg_mr function that can handle
partially initialized MRs, and fixing clean_mr to work on partially
initialized MRs.
Fixes: ff740aefec ("IB/mlx5: Decouple MR allocation and population flows")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The patch simplifies mlx5_ib_cont_pages and fixes the following
issues in the original implementation:
First issues is related to alignment of the PFNs. After the check
base + p != PFN, the alignment of the PFN wasn't checked. So the PFN
sequence 0, 1, 1, 2 would result in a page_shift of 13 even though
the 3rd PFN is not 8KB aligned.
This wasn't actually a bug because it was supported by all the
existing mlx5 compatible device, but we don't want to require
this support in all future devices.
Another issue is because the inner loop didn't advance PFN so
the test "if (base + p != pfn)" always failed for SGE with
len > (1<<page_shift).
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ib_mr->length represents the length of the MR in bytes as per
the IBTA spec 1.3 section 11.2.10.3 (REGISTER PHYSICAL MEMORY REGION).
Currently ib_mr->length field is defined as only 32-bits field.
This might result into truncation and failed WRs of consumers who
registers more than 4GB bytes memory regions and whose WRs accessing
such MRs.
This patch makes the length 64-bit to avoid such truncation.
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Fixes: 4c67e2bfc8 ("IB/core: Introduce new fast registration API")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The tag matching functionality is implemented by mlx5 driver
by extending XRQ, however this internal kernel information was
exposed to user space applications with *xrq* name instead of *tm*.
This patch renames *xrq* to *tm* to handle that.
Fixes: 8d50505ada ("IB/uverbs: Expose XRQ capabilities")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Smattering of miscellanous fixes
- A five patch series for i40iw that had a patch (5/5) that was larger
than I would like, but I took it because it's needed for large scale
users
- An 8 patch series for bnxt_re that landed right as I was leaving on
PTO and so had to wait until now...they are all appropriate fixes for
-rc IMO
-----BEGIN PGP SIGNATURE-----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=iiKF
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Smattering of miscellanous fixes
- A five patch series for i40iw that had a patch (5/5) that was larger
than I would like, but I took it because it's needed for large scale
users
- An 8 patch series for bnxt_re that landed right as I was leaving on
PTO and so had to wait until now...they are all appropriate fixes for
-rc IMO
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (22 commits)
bnxt_re: Don't issue cmd to delete GID for QP1 GID entry before the QP is destroyed
bnxt_re: Fix memory leak in FRMR path
bnxt_re: Remove RTNL lock dependency in bnxt_re_query_port
bnxt_re: Fix race between the netdev register and unregister events
bnxt_re: Free up devices in module_exit path
bnxt_re: Fix compare and swap atomic operands
bnxt_re: Stop issuing further cmds to FW once a cmd times out
bnxt_re: Fix update of qplib_qp.mtu when modified
i40iw: Add support for port reuse on active side connections
i40iw: Add missing VLAN priority
i40iw: Call i40iw_cm_disconn on modify QP to disconnect
i40iw: Prevent multiple netdev event notifier registrations
i40iw: Fail open if there are no available MSI-X vectors
RDMA/vmw_pvrdma: Fix reporting correct opcodes for completion
IB/bnxt_re: Fix frame stack compilation warning
IB/mlx5: fix debugfs cleanup
IB/ocrdma: fix incorrect fall-through on switch statement
IB/ipoib: Suppress the retry related completion errors
iw_cxgb4: remove the stid on listen create failure
iw_cxgb4: drop listen destroy replies if no ep found
...
FW needs the 0th GID Entry in the Table to be preserved before
it's corresponding QP1 is deleted, else it will fail the cmd.
Check for the same and return to prevent error msg being logged for
cmd failure.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch fixes a memory leak issue when alloc_mr is used.
mr->pages and mr->npages are used only in alloc_mr path. mr->pages
is allocated when alloc_mr is called or in the case of FRMR, while
creating the MR. mr->npages is updated only when the MR created
is used i.e. after invoking map_mr_sg verb, before data transfer.
In the dereg_mr path, if mr->npages is 0, driver ends up not freeing
the memory created.
Removing the npages check from the dereg_mr path for kernel consumers.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When there is a NETDEV_UNREGISTER event, bnxt_re driver calls
ib_unregister_device() (RTNL lock held).
ib_unregister_device attempts to flush a worker queue scheduled by
ib_core and that queue might have a pending ib_query_port().
ib_query_port in turn calls bnxt_re_query_port(), which while querying the
link speed using ib_get_eth_speed(), tries to acquire the rtnl_lock() which
was already held by NETDEV_UNREGISTER.
Fixing the issue by removing the link speed query from bnxt_re_query_port()
Now the speed is queried post a successful ib_register_device or whenever
there is a NETDEV_CHANGE event.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Upon receipt of the NETDEV_REGISTER event from the netdev notifier chain,
the IB stack registration is spawned off to a workqueue since that also
requires an rtnl lock.
There could be 2 kinds of races between the NETDEV_REGISTER and the
NETDEV_UNREGISTER event handling.
a)The NETDEV_UNREGISTER event is received in rapid succession after
the NETDEV_REGISTER event even before the work queue got a chance to run.
b)The NETDEV_UNREGISTER event is received while the workqueue that handles
registration with the IB stack is still in progress.
Handle both the races with a bit flag that is set just before the work item
is queued and cleared in the workqueue after the event is handled just
before the workqueue item is freed.
While adding the new flag, it was noted that the flags are all used in
*_bit() operations which expect a bit number and not a literal constant
with a bit set. So change the numbers to be bit numbers.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Clean up all devices added to the bnxt_re_dev_list in the
module_exit entry point.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver must assign the user supplied compare/swap values in
the wqe to successfully complete the atomic compare and
swap operation.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Once a cmd to FW times out(after 20s) it is reasonable to
assume the FW or atleast the control path is dead.
No point issuing further cmds to the FW as each subsequent cmd
with another 20s timeout will cascade resulting in unnecessary
traces and/or NMI Lockups.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The MTU value in the qplib_qp.mtu should be
consistent with whatever mtu was set during
INIT to RTR.The Next PSN and number of packets
are calculated based on this member in the qplib_qp structure.
Signed-off-by: Narender Reddy <narender.reddy@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
