bpf_skb_store_bytes() invocations above L2 header need BPF_F_RECOMPUTE_CSUM
flag for updates, so that CHECKSUM_COMPLETE will be fixed up along the way.
Where we ran into an issue with bpf_skb_store_bytes() is when we did a
single-byte update on the IPv6 hoplimit despite using BPF_F_RECOMPUTE_CSUM
flag; simple ping via ICMPv6 triggered a hw csum failure as a result. The
underlying issue has been tracked down to a buffer alignment issue.
Meaning, that csum_partial() computations via skb_postpull_rcsum() and
skb_postpush_rcsum() pair invoked had a wrong result since they operated on
an odd address for the hoplimit, while other computations were done on an
even address. This mix doesn't work as-is with skb_postpull_rcsum(),
skb_postpush_rcsum() pair as it always expects at least half-word alignment
of input buffers, which is normally the case. Thus, instead of these helpers
using csum_sub() and (implicitly) csum_add(), we need to use csum_block_sub(),
csum_block_add(), respectively. For unaligned offsets, they rotate the sum
to align it to a half-word boundary again, otherwise they work the same as
csum_sub() and csum_add().
Adding __skb_postpull_rcsum(), __skb_postpush_rcsum() variants that take the
offset as an input and adapting bpf_skb_store_bytes() to them fixes the hw
csum failures again. The skb_postpull_rcsum(), skb_postpush_rcsum() helpers
use a 0 constant for offset so that the compiler optimizes the offset & 1
test away and generates the same code as with csum_sub()/_add().
Fixes: 608cd71a9c ("tc: bpf: generalize pedit action")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I initially added the unsafe_[get|put]_user() helpers in commit
5b24a7a2aa ("Add 'unsafe' user access functions for batched
accesses"), I made the mistake of modeling the interface on our
traditional __[get|put]_user() functions, which return zero on success,
or -EFAULT on failure.
That interface is fairly easy to use, but it's actually fairly nasty for
good code generation, since it essentially forces the caller to check
the error value for each access.
In particular, since the error handling is already internally
implemented with an exception handler, and we already use "asm goto" for
various other things, we could fairly easily make the error cases just
jump directly to an error label instead, and avoid the need for explicit
checking after each operation.
So switch the interface to pass in an error label, rather than checking
the error value in the caller. Best do it now before we start growing
more users (the signal handling code in particular would be a good place
to use the new interface).
So rather than
if (unsafe_get_user(x, ptr))
... handle error ..
the interface is now
unsafe_get_user(x, ptr, label);
where an error during the user mode fetch will now just cause a jump to
'label' in the caller.
Right now the actual _implementation_ of this all still ends up being a
"if (err) goto label", and does not take advantage of any exception
label tricks, but for "unsafe_put_user()" in particular it should be
fairly straightforward to convert to using the exception table model.
Note that "unsafe_get_user()" is much harder to convert to a clever
exception table model, because current versions of gcc do not allow the
use of "asm goto" (for the exception) with output values (for the actual
value to be fetched). But that is hopefully not a limitation in the
long term.
[ Also note that it might be a good idea to switch unsafe_get_user() to
actually _return_ the value it fetches from user space, but this
commit only changes the error handling semantics ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is required to correctly interpret INET_DIAG_INFO messages exported
by sctp_diag module.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same kind of recursive sane default limit and policy
countrol that has been implemented for the user namespace
is desirable for the other namespaces, so generalize
the user namespace refernce count into a ucount.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add a structure that is per user and per user ns and use it to hold
the count of user namespaces. This makes prevents one user from
creating denying service to another user by creating the maximum
number of user namespaces.
Rename the sysctl export of the maximum count from
/proc/sys/userns/max_user_namespaces to /proc/sys/user/max_user_namespaces
to reflect that the count is now per user.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Export the export the maximum number of user namespaces as
/proc/sys/userns/max_user_namespaces.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Add a version of drm_plane_helper_check_update() which takes a plane
state instead of having the caller pass in everything.
And to reduce code duplication, let's reimplement
drm_plane_helper_check_update() in terms of the new function, by
having a tempororary plane state on the stack.
v2: Add a note that the functions modifies the state (Chris)
v3: Fix drm_plane_helper_check_update() y coordinates (Daniel Kurtz)
Cc: Daniel Kurtz <djkurtz@chromium.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org> (v2)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1470642910-14073-1-git-send-email-ville.syrjala@linux.intel.com
Limit per userns sysctls to only be opened for write by a holder
of CAP_SYS_RESOURCE.
Add all of the necessary boilerplate for having per user namespace
sysctls.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes hangs under memory pressure, e.g. running the piglit test
tex3d-maxsize concurrently with other tests.
Fixes: 17d33bc9d6 ("drm/ttm: drop waiting for idle in ttm_bo_evict.")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Ken Wang <Qingqing.Wang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
V2: fix the return value for fill failure and validate bo before
filling data
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the necessary boiler plate to move freeing of user namespaces into
work queue and thus into process context where things can sleep.
This is a necessary precursor to per user namespace sysctls.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Passing nsproxy into sysctl_table_root.lookup was a premature
optimization in attempt to avoid depending on current. The
directory /proc/self/sys has not appeared and if and when
it does this code will need to be reviewed closely and reworked
anyway. So remove the premature optimization.
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge@hallyn.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The AC100 is a multifunction device with an audio codec subsystem and
an RTC subsystem. These two subsystems share a common register space
and host interface.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch removes codec side duplicated callback function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the type and ABI struct for Backend DAIs. Add the number of BE DAIs
to manifest, and some reserved fields for future extensions.
Pump the version number to 5.
Topology core will check size of ABI objects to detect version mismatch
between user space and kernel.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The power() callback has always been empty so just remove it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds aptional GPIO bit-bang based callback implementations
for setting CLK, DATA and MODE L3 bus lines. It is added here
to avoid possible duplicate implementations across users of
the bus.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple-card needs to get its dai name and endpoint node.
This patch makes it simple style standard
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current simple-card can get clock via DT clocks or
"system-clock-frequency" property.
This patch makes it simple style standard
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some encoders need more information from crtc and connector state or
connector display info than just the mode during mode setting. This
patch adds an atomic encoder mode setting variant that passes the crtc
state (which contains the modes) and the connector state.
atomic_enable/disable variants that additionally pass crtc and connector
state don't seem to be necessary for any current driver. mode_fixup
already has an atomic equivalent in atomic_check.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the remaining missing IDMAC channel names: VDIC channels
for combining, the separate alpha channels for the MEM->IC and MEM->DC
ASYNC channels, and the DC read, command, and output mask channels.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the VDIC field input IDMAC channels. These channels
transfer fields F(n-1), F(n), and F(N+1) from memory to
the VDIC (channels 8, 9, 10 respectively).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds of-alias id to ipu_soc and retrieve with ipu_get_num().
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_set_uv_offset(), to set planar U/V offsets.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The 'de-active' and 'pixelclk-active' DT properties are evaluated
by of_parse_display_timing() called from of_get_drm_display_mode(),
but later lost in the conversion from videomode.flags to
drm_display_mode.flags.
Enhance of_get_drm_display_mode() to also return the bus flags in a
separate variable, so that they can be passed on to the ipu-di
driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
add a helper function to extract information about pixel clock and DE
polarity from DT for use by of_get_drm_display_mode().
While at it, convert spaces to tabs in indentation in drm_modes.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
It's super confusing that new drivers need to be marked with
DRIVER_MODESET when really it means DRIVER_MODERN. Much better to
invert the meaning and rename it to something that's suitably
off-putting.
Since there's over 100 places using DRIVER_MODESET we need to roll out
this change without a flag day.
v2: Update docs.
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470251470-30830-1-git-send-email-daniel.vetter@ffwll.ch
The minor referred to by "DRM_MINOR_LEGACY" is called 'dev->primary' and
gets 'cardX' as name assigned. Lets reduce this magnificent number of
names for the same concept by one and rename DRM_MINOR_LEGACY to
DRM_MINOR_PRIMARY (to match the actual struct-member name).
Furthermore, this is in no way a legacy node, so lets not call it that.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160803180432.1341-2-dh.herrmann@gmail.com
In addition to the last-in/first-out stack for accessing drm_mm nodes,
we occasionally and in the future often want to find a drm_mm_node by an
address. To do so efficiently we need to track the nodes in an interval
tree - lookups for a particular address will then be O(lg(N)), where N
is the number of nodes in the range manager as opposed to O(N).
Insertion however gains an extra O(lg(N)) step for all nodes
irrespective of whether the interval tree is in use. For future i915
patches, eliminating the linear walk is a significant improvement.
v2: Use generic interval-tree template for u64 and faster insertion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470236651-678-1-git-send-email-chris@chris-wilson.co.uk
A few fixes for amdgpu and ttm for 4.8
- fix a ttm regression caused by the new pipelining code
- fixes for mullins on amdgpu
- updated golden settings for amdgpu
* 'drm-next-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/ttm: Wait for a BO to become idle before unbinding it from GTT
drm/amdgpu: update golden setting of polaris10
drm/amdgpu: update golden setting of stoney
drm/amdgpu: update golden setting of polaris11
drm/amdgpu: update golden setting of carrizo
drm/amdgpu: update golden setting of iceland
drm/amd/amdgpu: change pptable output format from ASCII to binary
drm/amdgpu/ci: add mullins to default case for smc ucode
drm/amdgpu/gmc7: add missing mullins case
Add asm-usable variants of EXPORT_SYMBOL/EXPORT_SYMBOL_GPL. This
commit just adds the default implementation; most of the architectures
can simply add export.h to asm/Kbuild and start using <asm/export.h>
from assembler. The rest needs to have their <asm/export.h> define
everal macros and then explicitly include <asm-generic/export.h>
One area where the things might diverge from default is the alignment;
normally it's 8 bytes on 64bit targets and 4 on 32bit ones, both for
unsigned long and for struct kernel_symbol. Unfortunately, amd64 and
m68k are unusual - m68k aligns to 2 bytes (for both) and amd64 aligns
struct kernel_symbol to 16 bytes. For those we'll need asm/export.h to
override the constants used by generic version - KSYM_ALIGN and KCRC_ALIGN
for kernel_symbol and unsigned long resp. And no, __alignof__ would not
do the trick - on amd64 __alignof__ of struct kernel_symbol is 8, not 16.
More serious source of unpleasantness is treatment of function
descriptors on architectures that have those. Things like ppc64,
parisc, ia64, etc. need more than the address of the first insn to
call an arbitrary function. As the result, their representation of
pointers to functions is not the typical "address of the entry point" -
it's an address of a small static structure containing all the required
information (including the entry point, of course). Sadly, the asm-side
conventions differ in what the function name refers to - entry point or
the function descriptor. On ppc64 we do the latter;
bar: .quad foo
is what void (*bar)(void) = foo; turns into and the rare places where
we need to explicitly work with the label of entry point are dealt with
as DOTSYM(foo). For our purposes it's ideal - generic macros are usable.
However, parisc would have foo and P%foo used for label of entry point
and address of the function descriptor and
bar: .long P%foo
woudl be used instead. ia64 goes similar to parisc in that respect,
except that there it's @fptr(foo) rather than P%foo. Such architectures
need to define KSYM_FUNC that would turn a function name into whatever
is needed to refer to function descriptor.
What's more, on such architectures we need to know whether we are exporting
a function or an object - in assembler we have to tell that explicitly, to
decide whether we want EXPORT_SYMBOL(foo) produce e.g.
__ksymtab_foo: .quad foo
or
__ksymtab_foo: .quad @fptr(foo)
For that reason we introduce EXPORT_DATA_SYMBOL{,_GPL}(), to be used for
exports of data objects. On normal architectures it's the same thing
as EXPORT_SYMBOL{,_GPL}(), but on parisc-like ones they differ and the
right one needs to be used. Most of the exports are functions, so we
keep EXPORT_SYMBOL for those...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Adding a new callback that will provide the error result for a transaction.
The result is allocated on the stack and the callback should create a copy
if it wishes to retain the information after exiting. The result parameter
is now defined and takes over the dummy void pointer we placed in the
helper functions previously. dmaengine drivers should start converting
to the new "callback_result" callback in order to receive transaction
results.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patchs add the new EXTCON_CHG_WPT for Wireless Power Transfer[1].
The Wireless Power Transfer is the transmission of electronical energy
from a power source. The EXTCON_CHG_WPT has the EXTCON_TYPE_CHG.
[1] https://en.wikipedia.org/wiki/Wireless_power_transfer
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
This patch adds the new EXTCON_DISP_HMD id for Head-mounted Display[1] device.
The HMD device is usually for USB connector type So, the HMD connector
has the two extcon types of both EXTCON_TYPE_DISP and EXTCON_TYPE_USB.
[1] https://en.wikipedia.org/wiki/Head-mounted_display
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add EXTCON_DISP_DP for the Display external connector. For Type-C
connector the DisplayPort can work as an Alternate Mode(VESA DisplayPort
Alt Mode on USB Type-C Standard). The Type-C support both normal
and flipped orientation, so add a property to extcon.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch adds the synchronization extcon APIs to support the notifications
for both state and property. When extcon_*_sync() functions is called,
the extcon informs the information from extcon provider to extcon client.
The extcon driver may need to change the both state and multiple properties
at the same time. After setting the data of a external connector,
the extcon send the notification to client driver with the extcon_*_sync().
The list of new extcon APIs as following:
- extcon_sync() : Send the notification for each external connector to
synchronize the information between extcon provider driver
and extcon client driver.
- extcon_set_state_sync() : Set the state of external connector with noti.
- extcon_set_property_sync() : Set the property of external connector with noti.
For example,
case 1, change the state of external connector and synchronized the data.
extcon_set_state_sync(edev, EXTCON_USB, 1);
case 2, change both the state and property of external connector
and synchronized the data.
extcon_set_state(edev, EXTCON_USB, 1);
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS 1);
extcon_sync(edev, EXTCON_USB);
case 3, change the property of external connector and synchronized the data.
extcon_set_property(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
extcon_sync(edev, EXTCON_USB);
case 4, change the property of external connector and synchronized the data.
extcon_set_property_sync(edev, EXTCON_USB, EXTCON_PROP_USB_VBUS, 0);
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
This patch just renames the existing extcon_get/set_cable_state_()
as following because of maintaining the function naming pattern
like as extcon APIs for property.
- extcon_set_cable_state_() -> extcon_set_state()
- extcon_get_cable_state_() -> extcon_get_state()
But, this patch remains the old extcon_set/get_cable_state_() functions
to prevent the build break. After altering new APIs, remove the old APIs.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
