- sunxi: Correct time phase settings
- omap_hsmmc: Clean up some dead code
- dw_mmc: Fix message printed for deprecated num-slots DT binding
- dw_mmc: Fix DT documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xWHL
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Here are a couple of mmc fixes intended for v4.13-rc1.
I have also included a couple of cleanup patches in this pull request
for OMAP2+, related to the omap_hsmmc driver. The reason is because of
the changes are also depending on OMAP SoC specific code, so this
simplifies how to deal with this.
Summary:
MMC host:
- sunxi: Correct time phase settings
- omap_hsmmc: Clean up some dead code
- dw_mmc: Fix message printed for deprecated num-slots DT binding
- dw_mmc: Fix DT documentation"
* tag 'mmc-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
Documentation: dw-mshc: deprecate num-slots
mmc: dw_mmc: fix the wrong condition check of getting num-slots from DT
mmc: host: omap_hsmmc: remove unused platform callbacks
ARM: OMAP2+: hsmmc.c: Remove dead code
mmc: sunxi: Keep default timing phase settings for new timing mode
Arnd reported some false positive warnings with GCC 7:
drivers/hid/wacom_wac.o: warning: objtool: wacom_bpt3_touch()+0x2a5: stack state mismatch: cfa1=7+8 cfa2=6+16
drivers/iio/adc/vf610_adc.o: warning: objtool: vf610_adc_calculate_rates() falls through to next function vf610_adc_sample_set()
drivers/pwm/pwm-hibvt.o: warning: objtool: hibvt_pwm_get_state() falls through to next function hibvt_pwm_remove()
drivers/pwm/pwm-mediatek.o: warning: objtool: mtk_pwm_config() falls through to next function mtk_pwm_enable()
drivers/spi/spi-bcm2835.o: warning: objtool: .text: unexpected end of section
drivers/spi/spi-bcm2835aux.o: warning: objtool: .text: unexpected end of section
drivers/watchdog/digicolor_wdt.o: warning: objtool: dc_wdt_get_timeleft() falls through to next function dc_wdt_restart()
When GCC 7 detects a potential divide-by-zero condition, it sometimes
inserts a UD2 instruction for the case where the divisor is zero,
instead of letting the hardware trap on the divide instruction.
Objtool doesn't consider UD2 to be fatal unless it's annotated with
unreachable(). So it considers the GCC-generated UD2 to be non-fatal,
and it tries to follow the control flow past the UD2 and gets
confused.
Previously, objtool *did* assume UD2 was always a dead end. That
changed with the following commit:
d1091c7fa3 ("objtool: Improve detection of BUG() and other dead ends")
The motivation behind that change was that Peter was planning on using
UD2 for __WARN(), which is *not* a dead end. However, it turns out
that some emulators rely on UD2 being fatal, so he ended up using
'ud0' instead:
9a93848fe7 ("x86/debug: Implement __WARN() using UD0")
For GCC 4.5+, it should be safe to go back to the previous assumption
that UD2 is fatal, even when it's not annotated with unreachable().
But for pre-4.5 versions of GCC, the unreachable() macro isn't
supported, so such cases of UD2 need to be explicitly annotated as
reachable.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: d1091c7fa3 ("objtool: Improve detection of BUG() and other dead ends")
Link: http://lkml.kernel.org/r/e57fa9dfede25f79487da8126ee9cdf7b856db65.1501188854.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
-----BEGIN PGP SIGNATURE-----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=imPz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
- Add an ACPI module parameter to allow users to override the
new default behavior on some systems where the EC GPE is not
disabled during suspend-to-idle in case the EC on their systems
generates excessive wakeup events and they want to sacrifice
some functionality (like power button wakeups) for extra battery
life while suspended (Rafael Wysocki).
- Fix flushing of the outstanding EC work in the ACPI core
suspend-to-idle code (Rafael Wysocki).
- Add a missing include and fix a messed-up comment in the ACPI
NUMA code (Ross Zwisler).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=m4S0
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These are two fixups for the suspend-to-idle handling in the ACPI
subsystem after recent changes in that area and two simple fixes of
the ACPI NUMA code.
Specifics:
- Add an ACPI module parameter to allow users to override the new
default behavior on some systems where the EC GPE is not disabled
during suspend-to-idle in case the EC on their systems generates
excessive wakeup events and they want to sacrifice some
functionality (like power button wakeups) for extra battery life
while suspended (Rafael Wysocki).
- Fix flushing of the outstanding EC work in the ACPI core
suspend-to-idle code (Rafael Wysocki).
- Add a missing include and fix a messed-up comment in the ACPI NUMA
code (Ross Zwisler)"
* tag 'acpi-4.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: NUMA: Fix typo in the full name of SRAT
ACPI: NUMA: add missing include in acpi_numa.h
ACPI / PM / EC: Flush all EC work in acpi_freeze_sync()
ACPI / EC: Add parameter to force disable the GPE on suspend
Add power domain indices for R-Car D3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
That commit was part of the changes moving x86 to the generic CPU hotplug
interrupt migration code. The force flag was required on x86 before the
hierarchical irqdomain rework, but invoking set_affinity() with force=true
stayed and had no side effects.
At some point in the past, the force flag got repurposed to support the
exynos timer interrupt affinity setting to a not yet online CPU, so the
interrupt controller callback does not verify the supplied affinity mask
against cpu_online_mask.
Setting the flag in the CPU hotplug code causes the cpu online masking to
be blocked on these irq controllers and results in potentially affining an
interrupt to the CPU which is unplugged, i.e. instead of moving it away,
it's just reassigned to it.
As the force flags is not longer needed on x86, it's safe to revert that
patch so the ARM irqchips which use the force flag work again.
Add comments to that effect, so this won't happen again.
Note: The online mask handling should be done in the generic code and the
force flag and the masking in the irq chips removed all together, but
that's not a change possible for 4.13.
Fixes: 77f85e66aa ("genirq/cpuhotplug: Set force affinity flag on hotplug migration")
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707271217590.3109@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Although HID itself is transport-agnostic, occasionally a driver may
want to interact with the low-level transport that a device is connected
through. To do this, we need to know what kind of bus is in use. The
first guess may be to look at the 'bus' field of the 'struct hid_device',
but this field may be emulated in some cases (e.g. uhid).
More ideally, we can check which ll_driver a device is using. This
function introduces a 'hid_is_using_ll_driver' function and makes the
'struct hid_ll_driver' of the four most common transports accessible
through hid.h.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The number of supported WIDs, if they are supported at all, can be
limited due to resources. Notifying the user space application the
number of available WIDs allows it to utilize them correctly.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Direct Packet Mode support may be disabled, e.g, due to limited
resources. Notifying the user application prevents wasting cycles
on attempting to send these kind of packets.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since the PMU register interface is banked per CPU, CPU PMU interrrupts
cannot be handled by a CPU other than the one with the PMU asserting the
interrupt. This means that migrating PMU SPIs, as we do during a CPU
hotplug operation doesn't make any sense and can lead to the IRQ being
disabled entirely if we route a spurious IRQ to the new affinity target.
This has been observed in practice on AMD Seattle, where CPUs on the
non-boot cluster appear to take a spurious PMU IRQ when coming online,
which is routed to CPU0 where it cannot be handled.
This patch passes IRQF_PERCPU for PMU SPIs and forcefully sets their
affinity prior to requesting them, ensuring that they cannot
be migrated during hotplug events. This interacts badly with the DB8500
erratum workaround that ping-pongs the interrupt affinity from the handler,
so we avoid passing IRQF_PERCPU in that case by allowing the IRQ flags
to be overridden in the platdata.
Fixes: 3cf7ee98b8 ("drivers/perf: arm_pmu: move irq request/free into probe")
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Maximum coalesce per Rx/Tx queue is extended from
255 to 511.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b1f5bfc27a ("sctp: don't dereference ptr before leaving
_sctp_walk_{params, errors}()") tried to fix the issue that it
may overstep the chunk end for _sctp_walk_{params, errors} with
'chunk_end > offset(length) + sizeof(length)'.
But it introduced a side effect: When processing INIT, it verifies
the chunks with 'param.v == chunk_end' after iterating all params
by sctp_walk_params(). With the check 'chunk_end > offset(length)
+ sizeof(length)', it would return when the last param is not yet
accessed. Because the last param usually is fwdtsn supported param
whose size is 4 and 'chunk_end == offset(length) + sizeof(length)'
This is a badly issue even causing sctp couldn't process 4-shakes.
Client would always get abort when connecting to server, due to
the failure of INIT chunk verification on server.
The patch is to use 'chunk_end <= offset(length) + sizeof(length)'
instead of 'chunk_end < offset(length) + sizeof(length)' for both
_sctp_walk_params and _sctp_walk_errors.
Fixes: b1f5bfc27a ("sctp: don't dereference ptr before leaving _sctp_walk_{params, errors}()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU hotplug related code of this driver can be simplified by:
1) Consolidating the callbacks into a single state. The CPU thread can be
torn down on the CPU which goes offline. There is no point in delaying
that to the CPU dead state
2) Let the core code invoke the online/offline callbacks and remove the
extra for_each_online_cpu() loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The CPU hotplug related code of this driver can be simplified by:
1) Consolidating the callbacks into a single state. The CPU thread can be
torn down on the CPU which goes offline. There is no point in delaying
that to the CPU dead state
2) Let the core code invoke the online/offline callbacks and remove the
extra for_each_online_cpu() loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Backmerge drm-next with -rc2 in it to pull in a couple stm patches that
were previously incorrectly applied to -misc-next. By picking them up in
the correct manner, git will hopefully fix any errant trees that are out
in the wild.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZdS4PAAoJEHm+PkMAQRiGbEYH/2mukTPOUAfNoWaVjO2YHxuL
5yI3n1838tKIJm967IUmGdckN/RYGPjJxvZ+muXN2/rv23+9j3LVq9vQcsYqRQop
vrWP+hvGGJvOGJ2NYBDB+4AUrPPdeX9stolwyAcYvyCZ8AilPIovm4s2poA+fuQX
D78c8JSfpse32oc93dy4bUz3mRFKTeufstrWEuzqXI691mthF2G9EpA0R3hlbqv+
GiUnNcZVOnOuCt/47GnpWVKsyv91l3CkGq3bV1GSUi8a/1PnyFxHQxQI/qgbkLXs
NuswRupSeLDQKRgiDLgWF/BpdHEp4dpFFWXm00KWlgxeGSQnKat9bpW/d5OgnhA=
=mv3H
-----END PGP SIGNATURE-----
Backmerge tag 'v4.13-rc2' into drm-next
Linux 4.13-rc2
This is required for drm-misc fixing.
The bitmap allocator must keep metadata consistent. The easiest way is
to scan after every allocation for each affected block and the entire
chunk. This is rather expensive.
The free path can take advantage of current contig hints to prevent
scanning within the start and end block. If a scan is needed, it can
be done by scanning backwards from the start and forwards from the end
to identify the entire free area this can be combined with. The blocks
can then be updated by some basic checks rather than complete block
scans.
A chunk scan happens when the freed area makes a page free, a block
free, or spans across blocks. This is necessary as the contig hint at
this point could span across blocks. The check uses the minimum of page
size and the block size to allow for variable sized blocks. There is a
tradeoff here with not updating after every free. It is possible a
contig hint in one block can be merged with the contig hint in the next
block. This means the contig hint can be off by up to a page. However,
if the chunk's contig hint is contained in one block, the contig hint
will be accurate.
Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch introduces the bitmap metadata blocks and adds the skeleton
of the code that will be used to maintain these blocks. Each chunk's
bitmap is made up of full metadata blocks. These blocks maintain basic
metadata to help prevent scanning unnecssarily to update hints. Full
scanning methods are used for the skeleton and will be replaced in the
coming patches. A number of helper functions are added as well to do
conversion of pages to blocks and manage offsets. Comments will be
updated as the final version of each function is added.
There exists a relationship between PAGE_SIZE, PCPU_BITMAP_BLOCK_SIZE,
the region size, and unit_size. Every chunk's region (including offsets)
is page aligned at the beginning to preserve alignment. The end is
aligned to LCM(PAGE_SIZE, PCPU_BITMAP_BLOCK_SIZE) to ensure that the end
can fit with the populated page map which is by page and every metadata
block is fully accounted for. The unit_size is already page aligned, but
must also be aligned with PCPU_BITMAP_BLOCK_SIZE to ensure full metadata
blocks.
Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The percpu memory allocator is experiencing scalability issues when
allocating and freeing large numbers of counters as in BPF.
Additionally, there is a corner case where iteration is triggered over
all chunks if the contig_hint is the right size, but wrong alignment.
This patch replaces the area map allocator with a basic bitmap allocator
implementation. Each subsequent patch will introduce new features and
replace full scanning functions with faster non-scanning options when
possible.
Implementation:
This patchset removes the area map allocator in favor of a bitmap
allocator backed by metadata blocks. The primary goal is to provide
consistency in performance and memory footprint with a focus on small
allocations (< 64 bytes). The bitmap removes the heavy memmove from the
freeing critical path and provides a consistent memory footprint. The
metadata blocks provide a bound on the amount of scanning required by
maintaining a set of hints.
In an effort to make freeing fast, the metadata is updated on the free
path if the new free area makes a page free, a block free, or spans
across blocks. This causes the chunk's contig hint to potentially be
smaller than what it could allocate by up to the smaller of a page or a
block. If the chunk's contig hint is contained within a block, a check
occurs and the hint is kept accurate. Metadata is always kept accurate
on allocation, so there will not be a situation where a chunk has a
later contig hint than available.
Evaluation:
I have primarily done testing against a simple workload of allocation of
1 million objects (2^20) of varying size. Deallocation was done by in
order, alternating, and in reverse. These numbers were collected after
rebasing ontop of a80099a152. I present the worst-case numbers here:
Area Map Allocator:
Object Size | Alloc Time (ms) | Free Time (ms)
----------------------------------------------
4B | 310 | 4770
16B | 557 | 1325
64B | 436 | 273
256B | 776 | 131
1024B | 3280 | 122
Bitmap Allocator:
Object Size | Alloc Time (ms) | Free Time (ms)
----------------------------------------------
4B | 490 | 70
16B | 515 | 75
64B | 610 | 80
256B | 950 | 100
1024B | 3520 | 200
This data demonstrates the inability for the area map allocator to
handle less than ideal situations. In the best case of reverse
deallocation, the area map allocator was able to perform within range
of the bitmap allocator. In the worst case situation, freeing took
nearly 5 seconds for 1 million 4-byte objects. The bitmap allocator
dramatically improves the consistency of the free path. The small
allocations performed nearly identical regardless of the freeing
pattern.
While it does add to the allocation latency, the allocation scenario
here is optimal for the area map allocator. The area map allocator runs
into trouble when it is allocating in chunks where the latter half is
full. It is difficult to replicate this, so I present a variant where
the pages are second half filled. Freeing was done sequentially. Below
are the numbers for this scenario:
Area Map Allocator:
Object Size | Alloc Time (ms) | Free Time (ms)
----------------------------------------------
4B | 4118 | 4892
16B | 1651 | 1163
64B | 598 | 285
256B | 771 | 158
1024B | 3034 | 160
Bitmap Allocator:
Object Size | Alloc Time (ms) | Free Time (ms)
----------------------------------------------
4B | 481 | 67
16B | 506 | 69
64B | 636 | 75
256B | 892 | 90
1024B | 3262 | 147
The data shows a parabolic curve of performance for the area map
allocator. This is due to the memmove operation being the dominant cost
with the lower object sizes as more objects are packed in a chunk and at
higher object sizes, the traversal of the chunk slots is the dominating
cost. The bitmap allocator suffers this problem as well. The above data
shows the inability to scale for the allocation path with the area map
allocator and that the bitmap allocator demonstrates consistent
performance in general.
The second problem of additional scanning can result in the area map
allocator completing in 52 minutes when trying to allocate 1 million
4-byte objects with 8-byte alignment. The same workload takes
approximately 16 seconds to complete for the bitmap allocator.
V2:
Fixed a bug in pcpu_alloc_first_chunk end_offset was setting the bitmap
using bytes instead of bits.
Added a comment to pcpu_cnt_pop_pages to explain bitmap_weight.
Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently dm_dax_flush() is not being called, even if underlying dax
device supports write cache, because DAXDEV_WRITE_CACHE is not being
propagated up to the DM dax device.
If the underlying dax device supports write cache, set
DAXDEV_WRITE_CACHE on the DM dax device. This will cause dm_dax_flush()
to be called.
Fixes: abebfbe2f7 ("dm: add ->flush() dax operation support")
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When CONFIG_EEH=y and CONFIG_VFIO_SPAPR_EEH=n, build fails with the
following:
drivers/vfio/pci/vfio_pci.o: In function `.vfio_pci_release':
vfio_pci.c:(.text+0xa98): undefined reference to `.vfio_spapr_pci_eeh_release'
drivers/vfio/pci/vfio_pci.o: In function `.vfio_pci_open':
vfio_pci.c:(.text+0x1420): undefined reference to `.vfio_spapr_pci_eeh_open'
In this case, vfio_pci.c should use the empty definitions of
vfio_spapr_pci_eeh_open and vfio_spapr_pci_eeh_release functions.
This patch fixes it by guarding these function definitions with
CONFIG_VFIO_SPAPR_EEH, the symbol that controls whether vfio_spapr_eeh.c is
built, which is where the non-empty versions of these functions are. We need to
make use of IS_ENABLED() macro because CONFIG_VFIO_SPAPR_EEH is a tristate
option.
This issue was found during a randconfig build. Logs are here:
http://kisskb.ellerman.id.au/kisskb/buildresult/12982362/
Signed-off-by: Murilo Opsfelder Araujo <mopsfelder@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This will let drivers reduce the error cleanup they need, in
particular the "is_panel_bridge" flag.
v2: Slight cleanup of remove function by Andrzej
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170718210510.12229-2-eric@anholt.net
v4l2_subdev_call is a macro returning whatever the callback return
type is, usually 'int'. With gcc-7 and ccache, this can lead to
many wanings like:
media/platform/pxa_camera.c: In function 'pxa_mbus_build_fmts_xlate':
media/platform/pxa_camera.c:766:27: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
while (!v4l2_subdev_call(subdev, pad, enum_mbus_code, NULL, &code)) {
media/atomisp/pci/atomisp2/atomisp_cmd.c: In function 'atomisp_s_ae_window':
media/atomisp/pci/atomisp2/atomisp_cmd.c:6414:52: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
if (v4l2_subdev_call(isp->inputs[asd->input_curr].camera,
The problem here is that after preprocessing, we the compiler
sees a variation of
if (a ? 0 : 2)
that it thinks is suspicious.
This replaces the ?: operator with an different expression that
does the same thing in a more easily readable way that cannot
tigger the warning
Link: https://lkml.org/lkml/2017/7/14/156
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify and improve the code so that the PID is always available in
the uevent even when debugfs is not available.
This adds a userspace_pid field to struct kvm, as per Radim's
suggestion, so that the PID can be retrieved on destruction too.
Acked-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Fixes: 286de8f6ac ("KVM: trigger uevents when creating or destroying a VM")
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nothing calls this wrapper anymore, so just remove it and rename the
old function to get rid of the double underscore prefix.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
This patch increases the minimum allocation size of percpu memory to
4-bytes. This change will help minimize the metadata overhead
associated with the bitmap allocator. The assumption is that most
allocations will be of objects or structs greater than 2 bytes with
integers or longs being used rather than shorts.
The first chunk regions are now aligned with the minimum allocation
size. The reserved region is expected to be set as a multiple of the
minimum allocation size. The static region is aligned up and the delta
is removed from the dynamic size. This works because the dynamic size is
increased to be page aligned. If the static size is not minimum
allocation size aligned, then there must be a gap that is added to the
dynamic size. The dynamic size will never be smaller than the set value.
Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The V4L2 flash class initialisation expects struct led_classdev_flash that
describes an indicator but only uses struct led_classdev which is a field
iled_cdev in the struct. Use struct iled_cdev only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current drm_atomic_helper_commit_tail helper works only if the CRTC is
accessible, and documents an alternative implementation that is supposed to
be used if that happens.
That implementation is then duplicated by some drivers. Instead of
documenting it, let's implement an helper that all the relevant users can
use directly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a8f92dc70048bab746e94dadd1c23200626aff60.1500555652.git-series.maxime.ripard@free-electrons.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
FB helper code falls back to a 1024x768 mode if no outputs are connected
or don't report back any modes upon initialization. This can be annoying
because outputs that are added to FB helper later on can't be used with
FB helper if they don't support a matching mode.
The fallback is in place because VGA connectors can happen to report an
unknown connection status even when they are in fact connected.
Some drivers have custom solutions in place to defer FB helper setup
until at least one output is connected. But the logic behind these
solutions is always the same and there is nothing driver-specific about
it, so a better alterative is to fix the FB helper core and add support
for all drivers automatically.
This patch adds support for deferred FB helper setup. It checks all the
connectors for their connection status, and if all of them report to be
disconnected marks the FB helper as needing deferred setup. Whet setup
is deferred, the FB helper core will automatically retry setup after a
hotplug event, and it will keep trying until it succeeds.
v2: Rebase onto my entirely reworked fbdev helper locking. One big
difference is that this version again drops&reacquires the fbdev lock
(which is now fb_helper->lock, but before this patch series it was
mode_config->mutex), because register_framebuffer must be able to
recurse back into fbdev helper code for the initial screen setup.
v3: __drm_fb_helper_initial_config must hold fb_helper->lock upon
return, I've fumbled that in the deferred setup case (Liviu).
v4: I was blind, redo this all. __drm_fb_helper_initial_config
shouldn't need to reacquire fb_helper->lock, that just confuses
callers. I myself got confused by kernel_fb_helper_lock and somehow
thought it's the same as fb_helper->lock. Tsk.
Also simplify the logic a bit (we don't need two functions to probe
connectors), we can stick much closer to the existing code. And update
some comments I've spotted that are outdated.
v5: Don't pass -EAGAIN to drivers, it's just an internal error code
(Liviu).
v6: Add _and_unlock suffix to clarify locking (Maarten)
Cc: Liviu Dudau <liviu@dudau.co.uk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com> (v1)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@intel.com>
Reviewed-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706130023.28417-3-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
snd_soc_codec .cache_bypass related operation code has been removed.
Let's remove remaining code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that all drivers check the return value, convert swap_state to
__must_check. This is done separately to force build warnings if we
missed a driver.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-12-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add the new ORC unwinder which is enabled by CONFIG_ORC_UNWINDER=y.
It plugs into the existing x86 unwinder framework.
It relies on objtool to generate the needed .orc_unwind and
.orc_unwind_ip sections.
For more details on why ORC is used instead of DWARF, see
Documentation/x86/orc-unwinder.txt - but the short version is
that it's a simplified, fundamentally more robust debugninfo
data structure, which also allows up to two orders of magnitude
faster lookups than the DWARF unwinder - which matters to
profiling workloads like perf.
Thanks to Andy Lutomirski for the performance improvement ideas:
splitting the ORC unwind table into two parallel arrays and creating a
fast lookup table to search a subset of the unwind table.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: live-patching@vger.kernel.org
Link: http://lkml.kernel.org/r/0a6cbfb40f8da99b7a45a1a8302dc6aef16ec812.1500938583.git.jpoimboe@redhat.com
[ Extended the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently kasan_check_read/write() accept 'const void*', make them
accept 'const volatile void*'. This is required for instrumentation
of atomic operations and there is just no reason to not allow that.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kasan-dev@googlegroups.com
Cc: linux-mm@kvack.org
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/33e5ec275c1ee89299245b2ebbccd63709c6021f.1498140838.git.dvyukov@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allow calling cec_notifier_set_phys_addr and
cec_notifier_set_phys_addr_from_edid with a NULL notifier, in which
case these functions do nothing.
Add a cec_notifier_phys_addr_invalidate helper function (the notifier
equivalent of cec_phys_addr_invalidate).
These changes simplify drm CEC driver support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 7d3002cc8c ("iommu/core: split mapping to page sizes as supported
by the hardware") replaced 'int gfp_order' with a 'size_t size' of
iommu_map / iommu_unmap function arguments, but missed the function
prototypes for the disabled CONFIG_IOMMU_API case, let's correct them
for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then
the type and its helpers
-----BEGIN PGP SIGNATURE-----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=FeA7
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid
Pull uuid fixes from Christoph Hellwig:
- add a missing "!" in the uuid tests
- remove the last remaining user of the uuid_be type, and then the type
and its helpers
* tag 'uuid-for-4.13-2' of git://git.infradead.org/users/hch/uuid:
uuid: remove uuid_be
thunderbolt: use uuid_t instead of uuid_be
uuid: fix incorrect uuid_equal conversion in test_uuid_test
- split the global dma coherent pool from the per-device pool.
This fixes a regression in the earlier 4.13 pull requests where the
global pool would override a per-device CMA pool. (Vladimir Murzin).
-----BEGIN PGP SIGNATURE-----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=fJWP
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma mapping fixes from Christoph Hellwig:
"split the global dma coherent pool from the per-device pool.
This fixes a regression in the earlier 4.13 pull requests where the
global pool would override a per-device CMA pool (Vladimir Murzin)"
* tag 'dma-mapping-4.13-2' of git://git.infradead.org/users/hch/dma-mapping:
ARM: NOMMU: Wire-up default DMA interface
dma-coherent: introduce interface for default DMA pool
The policy->transition_latency field is used for multiple purposes
today and its not straight forward at all. This is how it is used:
A. Set the correct transition_latency value.
B. Set it to CPUFREQ_ETERNAL because:
1. We don't want automatic dynamic switching (with
ondemand/conservative) to happen at all.
2. We don't know the transition latency.
This patch handles the B.1. case in a more readable way. A new flag for
the cpufreq drivers is added to disallow use of cpufreq governors which
have dynamic_switching flag set.
All the current cpufreq drivers which are setting transition_latency
unconditionally to CPUFREQ_ETERNAL are updated to use it. They don't
need to set transition_latency anymore.
There shouldn't be any functional change after this patch.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
