[ Upstream commit ca29fd7cce ]
When process the outbound packet of ipv6, we should assign the master
device to output device other than input device.
Signed-off-by: Keefe Liu <liuqifa@huawei.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c19f846d5 ]
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216f ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe8 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 654d573845 ]
rcu_read_lock in tun_build_skb is used to rcu_dereference tun->xdp_prog
safely, rcu_read_unlock should be done in every return path.
Now I could see one place missing it, where it returns NULL in switch-case
XDP_REDIRECT, another palce using rcu_read_lock wrongly, where it returns
NULL in if (xdp_xmit) chunk.
So fix both in this patch.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c33ee15b38 ]
tun_recvmsg() supports accepting skb by msg_control after
commit ac77cfd425 ("tun: support receiving skb through msg_control"),
the skb if presented should be freed no matter how far it can go
along, otherwise it would be leaked.
This patch fixes several missed cases.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61d7853784 ]
tap_recvmsg() supports accepting skb by msg_control after
commit 3b4ba04acc ("tap: support receiving skb from msg_control"),
the skb if presented should be freed within the function, otherwise
it would be leaked.
Signed-off-by: Wei Xu <wexu@redhat.com>
Reported-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 45ab4b13e4 ]
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a4abd7a80a ]
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e77d7a554 ]
Commit 6fa1ba6152 partially
implemented the new ethtool API, by replacing get_settings()
with get_link_ksettings(). This breaks ethtool, since the
userspace tool (according to the new API specs) never tries
the legacy set() call, when the new get() call succeeds.
All attempts to chance some setting from userspace result in:
> Cannot set new settings: Operation not supported
Implement the missing set() call.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 134059fd27 ]
Offload IP header checksum to NIC.
This fixes a previous patch which disabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting disabled for IPv4 pkts. And HW is dropping these pkts
for some reason.
Without this patch, IPv4 TSO appears to be broken:
WIthout this patch I get ~16kbyte/s, with patch close to 2mbyte/s
when copying files via scp from test box to my home workstation.
Looking at tcpdump on sender it looks like hardware drops IPv4 TSO skbs.
This patch restores performance for me, ipv6 looks good too.
Fixes: fa6d7cb5d7 ("net: thunderx: Fix TCP/UDP checksum offload for IPv6 pkts")
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Aleksey Makarov <aleksey.makarov@auriga.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa6d7cb5d7 ]
Don't offload IP header checksum to NIC.
This fixes a previous patch which enabled checksum offloading
for both IPv4 and IPv6 packets. So L3 checksum offload was
getting enabled for IPv6 pkts. And HW is dropping these pkts
as it assumes the pkt is IPv4 when IP csum offload is set
in the SQ descriptor.
Fixes: 3a9024f52c ("net: thunderx: Enable TSO and checksum offloads for ipv6")
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f9409e7f08 ]
Quectel BG96 is an Qualcomm MDM9206 based IoT modem, supporting both
CAT-M and NB-IoT. Tested hardware is BG96 mounted on Quectel development
board (EVB). The USB id is added to qmi_wwan.c to allow QMI
communication with the BG96.
Signed-off-by: Sebastian Sjoholm <ssjoholm@mac.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fd7eafd021 ]
geneve->sock4/6 were added with geneve_open and released with geneve_stop.
So when geneve link down, we will not able to show remote address and
checksum info after commit 11387fe4a9 ("geneve: fix fill_info when using
collect_metadata").
Fix this by avoid passing *_REMOTE{,6} for COLLECT_METADATA since they are
mutually exclusive, and always show UDP_ZERO_CSUM6_RX info.
Fixes: 11387fe4a9 ("geneve: fix fill_info when using collect_metadata")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c3ab204f4 ]
Hardware has no notion of new or last mask id, instead it makes use of the
message type (i.e. add flow or del flow) in combination with a single bit
in metadata flags to determine when to add or delete a mask id. Previously
we made use of the new or last flags to indicate that a new mask should be
allocated or deallocated, respectively. This incorrect behaviour is fixed
by making use single bit in metadata flags to indicate mask allocation or
deallocation.
Fixes: 43f84b72c5 ("nfp: add metadata to each flow offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 743ba5b47f ]
The PF netdev is used for data transfer for reprs, so reprs inherit the
maximum MTU settings of the PF netdev.
Fixes: 5de73ee467 ("nfp: general representor implementation")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d35ef8f846 ]
In the cases where len is too long, the error return path fails to
kfree allocated buffers buf and usb_reg_buf. The simplest fix is to
perform the sanity check on len before the allocations to avoid having
to do the kfree'ing in the first place.
Detected by CoverityScan, CID#1452258,1452259 ("Resource Leak")
Fixes: 59f73e2ae1 ("rsi: check length before USB read/write register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 67bd523861 ]
hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator. mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later. Free the first copy before returning.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c3de777bd upstream.
In the function brcmf_sdio_firmware_callback() the driver is
unbound from the sdio function devices in the error path.
However, the order in which it is done resulted in a use-after-free
issue (see brcmf_ops_sdio_remove() in bcmsdh.c). Hence change
the order and first unbind sdio function #2 device and then
unbind sdio function #1 device.
Fixes: 7a51461fc2 ("brcmfmac: unbind all devices upon failure in firmware callback")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d0fc5a50a upstream.
Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.
[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b13f43a485 upstream.
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c2d49fdc5 upstream.
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0b9832b712 upstream.
When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.
While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.
Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.
We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf19037074 upstream.
When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.
[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91785de6f9 upstream.
Don't rely on can_get_echo_skb() return value to wake the network tx
queue up: can_get_echo_skb() returns 0 if the echo array slot was not
occupied, but also when the DLC of the released echo frame was 0.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12147edc43 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a31ced3de upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd352e1adf upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7f3302330 upstream.
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6aa8d59455 upstream.
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bd13bd522 upstream.
Avoid flooding the kernel log with "Formate error", if incomplete message
are received.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e84f44eb55 upstream.
The conditon in the while-loop becomes true when actual_length is less than
2 (MSG_HEADER_LEN). In best case we end up with a former, already
dispatched msg, that got msg->len greater than actual_length. This will
result in a "Format error" error printout.
Problem seen when unplugging a Kvaser USB device connected to a vbox guest.
warning: comparison between signed and unsigned integer expressions
[-Wsign-compare]
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 435019b480 upstream.
The allocated buffer was not freed if usb_submit_urb() failed.
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6c23b174c upstream.
After commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget.
So we need to return budget if there are still packets to receive.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c2cb02edf upstream.
PCI/PCIe drivers for PEAK-System CAN/CAN-FD interfaces do some access to the
PCI config during probing. In case one of these accesses fails, a POSITIVE
PCIBIOS_xxx error code is returned back. This POSITIVE error code MUST be
converted into a NEGATIVE errno for the probe() function to indicate it
failed. Using the pcibios_err_to_errno() function, we make sure that the
return code will always be negative.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1cb35a33a2 upstream.
Currently, when you disconnect the device, the driver infinitely
resubmits all URBs, so you see:
Rx URB aborted (-32)
in an infinite loop.
Fix this by catching -EPIPE (what we get in urb->status when the device
disconnects) and not resubmitting.
With this patch, I can plug and unplug many times and the driver
recovers correctly.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0f4b163a0 upstream.
This is a follow on to commit b10effb92e ("fix buffer overrun while the
I219 is processing DMA transactions") to address David Laights concerns
about the use of "magic" numbers. So define masks as well as add
additional code comments to give a better understanding of what needs to
be done to avoid a buffer overrun.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Alexander H Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b10effb92e upstream.
Intel® 100/200 Series Chipset platforms reduced the round-trip
latency for the LAN Controller DMA accesses, causing in some high
performance cases a buffer overrun while the I219 LAN Connected
Device is processing the DMA transactions. I219LM and I219V devices
can fall into unrecovered Tx hang under very stressfully UDP traffic
and multiple reconnection of Ethernet cable. This Tx hang of the LAN
Controller is only recovered if the system is rebooted. Slightly slow
down DMA access by reducing the number of outstanding requests.
This workaround could have an impact on TCP traffic performance
on the platform. Disabling TSO eliminates performance loss for TCP
traffic without a noticeable impact on CPU performance.
Please, refer to I218/I219 specification update:
https://www.intel.com/content/www/us/en/embedded/products/networking/
ethernet-connection-i218-family-documentation.html
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4aea7a5c5e upstream.
When e1000e_poll() is not fast enough to keep up with incoming traffic, the
adapter (when operating in msix mode) raises the Other interrupt to signal
Receiver Overrun.
This is a double problem because 1) at the moment e1000_msix_other()
assumes that it is only called in case of Link Status Change and 2) if the
condition persists, the interrupt is repeatedly raised again in quick
succession.
Ideally we would configure the Other interrupt to not be raised in case of
receiver overrun but this doesn't seem possible on this adapter. Instead,
we handle the first part of the problem by reverting to the practice of
reading ICR in the other interrupt handler, like before commit 16ecba59bc
("e1000e: Do not read ICR in Other interrupt"). Thanks to commit
0a8047ac68 ("e1000e: Fix msi-x interrupt automask") which cleared IAME
from CTRL_EXT, reading ICR doesn't interfere with RxQ0, TxQ0 interrupts
anymore. We handle the second part of the problem by not re-enabling the
Other interrupt right away when there is overrun. Instead, we wait until
traffic subsides, napi polling mode is exited and interrupts are
re-enabled.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Fixes: 16ecba59bc ("e1000e: Do not read ICR in Other interrupt")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19110cfbb3 upstream.
Lennart reported the following race condition:
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
/* link is up */
mac->get_link_status = false;
/* interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true;
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3509f8bc7 upstream.
All the helpers return -E1000_ERR_PHY.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4c40e51f9 upstream.
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac4df1c5f upstream.
Newer firmware versions (such as iwlwifi-8000C-34.ucode) have
introduced an API change in the SCAN_REQ_UMAC command that is not
backwards compatible. The driver needs to detect and use the new API
format when the firmware reports it, otherwise the scan command will
not work properly, causing a command timeout.
Fix this by adding a TLV that tells the driver that the new API is in
use and use the correct structures for it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=197591
Fixes: d7a5b3e9e4 ("iwlwifi: mvm: bump API to 34 for 8000 and up")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dbc89253a7 upstream.
A lot of PCI IDs were missing and there were some problems with the
configuration and firmware selection for devices on the 9000 series.
Fix the firmware selection by adding files for the B-steps; add
configuration for some integrated devices; and add a bunch of PCI IDs
(mostly for integrated devices) that were missing from the driver's
list.
Without this patch, a lot of devices will not be recognized or will
try to load the wrong firmware file.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1105a33737 upstream.
It's hard to find values that are missing in the list, so sorting the
values and comparing them makes it much easier. To simplify this
task, sort the devices in the list.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7f5873bbd upstream.
The PCI ID (0x2720, 0x0070) was set with the config struct
iwla000_2ax_cfg_hr instead of iwla000_2ac_cfg_hr_cdb.
Fixes: 175b87c692 ("iwlwifi: add the new a000_2ax series")
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cc: Thomas Backlund <tmb@mageia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
