Enable power saving for RTS5250S as following steps:
1.Set 0xFE58 to enable clock power management.
2.Check cfg space whether support L1SS or not.
3.If support L1SS, set 0xFF03 to free clkreq.
4.When entering idle status, enable aspm
and set parameters for L1SS and LTR.
5.Wnen entering run status, disable aspm
and set parameters for L1SS and LTR.
If entering L1SS mode successfully,
electric current will be below 2mA.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
More 4.15 drm-misc stuff:
Cross-subsystem Changes:
- bridge cleanup refactor (Benjamin Gaignard)
Core Changes:
- less surprising atomic iterators (Maarten), fixes an oops introduced
in drm-next
- better gem/fb helper docs (Noralf)
- fix dma-buf rcu races (Christian König)
Driver Changes:
- adv7511: CEC support (Hans Verkuil)
- sun4i update from Chen-Yu to improve hdmi and A31 support
- sii8620: add remote control support (Maceiej Purski)
New drivers:
- SiI9234 bridge driver (Maciej Purski)
- 7" rpi touch panel (Eric Anholt)
Note that this contains a topic pull from regmap, needed by the sun4i
changes. Mark Brown sent that out for pulling into drm-misc.
* tag 'drm-misc-next-2017-10-12' of git://anongit.freedesktop.org/drm/drm-misc: (29 commits)
drm/dp: WARN about invalid/unknown link rates and bw codes
drm/msm/mdp5: remove less than 0 comparison for unsigned value
drm/bridge/sii8620: add remote control support
drm/sun4i: hdmi: Add support for A31's HDMI controller
drm/sun4i: hdmi: Add A31 specific DDC register definitions
drm/sun4i: hdmi: Add support for controller hardware variants
dt-bindings: display: sun4i: Add binding for A31 HDMI controller
drm/sun4i: hdmi: Allow using second PLL as TMDS clk parent
drm/sun4i: hdmi: create a regmap for later use
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/sun4i: tcon: Add support for demuxing TCON output on A31
drm/sun4i: tcon: Add variant callback for TCON output muxing
drm/bridge/synopsys: dsi :remove is_panel_bridge
drm/vc4: remove bridge from driver internal structure
drm/stm: ltdc: remove bridge from driver internal structure
drm/drm_of: add drm_of_panel_bridge_remove function
drm/bridge: make drm_panel_bridge_remove more robust
dma-fence: fix dma_fence_get_rcu_safe v2
dma-buf: make reservation_object_copy_fences rcu save
drm/atomic: Unref duplicated drm_atomic_state in drm_atomic_helper_resume()
...
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the parameter updating via RCU and not protected by a
spinlock anymore. This reduce the time that the spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make style of module alias name consistent with other subsystems in kernel,
for example net devices.
Fixes: 084e2f6566 ("Support to encoding decoding skb mark on IFE action")
Fixes: 200e10f469 ("Support to encoding decoding skb prio on IFE action")
Fixes: 408fbc22ef ("net sched ife action: Introduce skb tcindex metadata encap decap")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drm vblank handling uses 'timeval' to store timestamps in either
monotonic or wall-clock time base. In either case, it reads the current
time as a ktime_t in get_drm_timestamp() and converts it from there.
This is a bit suspicious, as users of 'timeval' often suffer from
the time_t overflow in y2038. I have gone through this code and
found that it is unlikely to cause problems here:
- The user space ABI does not use time_t or timeval, but uses
'u32' and 'long' as the types. This means at least that rebuilding
user programs against a new libc with 64-bit time_t does not
change the ABI.
- As of commit c61eef726a ("drm: add support for monotonic vblank
timestamps") in linux-3.8, the monotonic timestamp is the default
and can only get reverted to wall-clock through a module-parameter.
- With the default monotonic timestamps, there is no problem at all.
- The drm_wait_vblank_ioctl() interface is alway safe on 64-bit
architectures, on 32-bit it might overflow the 'long' timestamps
in 2038 with wall-clock timestamps.
- The event handling uses 'u32' seconds, which overflow in 2106
on both 32-bit and 64-bit machines, when wall-clock timestamps
are used.
- The effect of overflowing either of the two is only temporary
(during the overflow, and is likely to keep working again
afterwards. It is likely the same problem as observing a
'settimeofday()' call, which was the reason for moving to the
monotonic timestamps in the first place.
Overall, this seems good enough, so my patch removes the use of
'timeval' from the vblank handling altogether and uses ktime_t
consistently, except for the part where we copy the data to user
space structures in the existing format.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This file contains unnecessary whitespaces as newlines, remove them,
found by looking at what struct tc_mirred looks like.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove three inline helpers that are no longer needed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a busy week for defending the attacks from fuzzer people;
this pull request contains various USB-audio driver fixes and
sequencer core fixes spotted by syzkaller and other fuzzer, as well
as one quirk for a Plantronics USB audio device.
-----BEGIN PGP SIGNATURE-----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=sl20
-----END PGP SIGNATURE-----
Merge tag 'sound-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It's been a busy week for defending the attacks from fuzzer people.
This contains various USB-audio driver fixes and sequencer core fixes
spotted by syzkaller and other fuzzer, as well as one quirk for a
Plantronics USB audio device"
* tag 'sound-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: caiaq: Fix stray URB at probe error path
ALSA: seq: Fix use-after-free at creating a port
ALSA: usb-audio: Kill stray URB at exiting
ALSA: line6: Fix leftover URB at error-path during probe
ALSA: line6: Fix NULL dereference at podhd_disconnect()
ALSA: line6: Fix missing initialization before error path
ALSA: seq: Fix copy_from_user() call inside lock
ALSA: usb-audio: Add sample rate quirk for Plantronics P610
DH_KPP_SECRET_MIN_SIZE and dh_data_size() are both returning
unsigned values.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ECDH_KPP_SECRET_MIN_SIZE and params->key_size are both returning
unsigned values.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).
The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).
This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).
Fixes: fddddb52a6 ("bus: introduce an Marvell EBU MBus driver")
CC: stable@vger.kernel.org
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since IOVA allocation failure is not unusual case we need to flush
CPUs' rcache in hope we will succeed in next round.
However, it is useful to decide whether we need rcache flush step because
of two reasons:
- Not scalability. On large system with ~100 CPUs iterating and flushing
rcache for each CPU becomes serious bottleneck so we may want to defer it.
- free_cpu_cached_iovas() does not care about max PFN we are interested in.
Thus we may flush our rcaches and still get no new IOVA like in the
commonly used scenario:
if (dma_limit > DMA_BIT_MASK(32) && dev_is_pci(dev))
iova = alloc_iova_fast(iovad, iova_len, DMA_BIT_MASK(32) >> shift);
if (!iova)
iova = alloc_iova_fast(iovad, iova_len, dma_limit >> shift);
1. First alloc_iova_fast() call is limited to DMA_BIT_MASK(32) to get
PCI devices a SAC address
2. alloc_iova() fails due to full 32-bit space
3. rcaches contain PFNs out of 32-bit space so free_cpu_cached_iovas()
throws entries away for nothing and alloc_iova() fails again
4. Next alloc_iova_fast() call cannot take advantage of rcache since we
have just defeated caches. In this case we pick the slowest option
to proceed.
This patch reworks flushed_rcache local flag to be additional function
argument instead and control rcache flush step. Also, it updates all users
to do the flush as the last chance.
Signed-off-by: Tomasz Nowicki <Tomasz.Nowicki@caviumnetworks.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The secure IO service provides operations for reading and writing secure
memory from non-secure mode, expose this API through SCM.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The helper and the struct field ares no longer used by any code,
so remove them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user of cls_flower->egress_dev is mlx5. So do the conversion
there alongside with the code originating the call in cls_flower
function fl_hw_replace_filter to the newly introduced egress device
callback infrastucture.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure that allows drivers to register callbacks that
are called whenever tc would offload inserted rule and specified device
acts as tc action egress device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return dev directly, NULL if not possible. That is enough.
Makes no sense to pass struct net * to get_dev op, as there is only one
net possible, the one the action was created in. So just store it in
mirred priv and use directly.
Rename the mirred op callback function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For kvec and bvec: feeds segments to given callback as long as it
returns 0. For iovec and pipe: fails.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
- lib/scatterlist updates, use for userptr allocations (Tvrtko)
- Fixed point wrapper cleanup (Mahesh)
- Gen9+ transition watermarks, watermark optimization and fixes (Mahesh)
- Display IPC (Isochronous Priority Control) support (Mahesh)
- GEM workaround fixes (Oscar)
- GVT: PCI config sanitize series (Changbin)
- GVT: Workload submission error handling series (Fred)
- PSR fixes and refactoring (Rodrigo)
- HWSP based optimizations (Chris)
- Private PAT management (Zhi)
- IRQ handling fixes and refactoring (Ville)
- Module parameter refactoring and variable name clash fix (Michal)
- Execlist refactoring, incomplete request unwinding on reset (Chris)
- GuC scheduling improvements (Michal)
- OA updates (Lionel)
- Coffeelake out of alpha support (Rodrigo)
- seqno fixes (Chris)
- Execlist refactoring (Mika)
- DP and DP MST cleanups (Dhinakaran)
- Cannonlake slice/sublice config (Ben)
- Numerous fixes all around (Everyone)
-----BEGIN PGP SIGNATURE-----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=qpkh
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2017-09-29' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
2nd batch of v4.15 features:
- lib/scatterlist updates, use for userptr allocations (Tvrtko)
- Fixed point wrapper cleanup (Mahesh)
- Gen9+ transition watermarks, watermark optimization and fixes (Mahesh)
- Display IPC (Isochronous Priority Control) support (Mahesh)
- GEM workaround fixes (Oscar)
- GVT: PCI config sanitize series (Changbin)
- GVT: Workload submission error handling series (Fred)
- PSR fixes and refactoring (Rodrigo)
- HWSP based optimizations (Chris)
- Private PAT management (Zhi)
- IRQ handling fixes and refactoring (Ville)
- Module parameter refactoring and variable name clash fix (Michal)
- Execlist refactoring, incomplete request unwinding on reset (Chris)
- GuC scheduling improvements (Michal)
- OA updates (Lionel)
- Coffeelake out of alpha support (Rodrigo)
- seqno fixes (Chris)
- Execlist refactoring (Mika)
- DP and DP MST cleanups (Dhinakaran)
- Cannonlake slice/sublice config (Ben)
- Numerous fixes all around (Everyone)
* tag 'drm-intel-next-2017-09-29' of git://anongit.freedesktop.org/drm/drm-intel: (168 commits)
drm/i915: Update DRIVER_DATE to 20170929
drm/i915: Use memset64() to prefill the GTT page
drm/i915: Also discard second CRC on gen8+ platforms.
drm/i915/psr: Set frames before SU entry for psr2
drm/dp: Add defines for latency in sink
drm/i915: Allow optimized platform checks
drm/i915: Avoid using dev_priv->info.gen directly.
i915: Use %pS printk format for direct addresses
drm/i915/execlists: Notify context-out for lost requests
drm/i915/cnl: Add support slice/subslice/eu configs
drm/i915: Compact device info access by a small re-ordering
drm/i915: Add IS_PLATFORM macro
drm/i915/selftests: Try to recover from a wedged GPU during reset tests
drm/i915/huc: Reorganize HuC authentication
drm/i915: Fix default values of some modparams
drm/i915: Extend I915_PARAMS_FOR_EACH with default member value
drm/i915: Make I915_PARAMS_FOR_EACH macro more flexible
drm/i915: Enable scanline read based on frame timestamps
drm/i915/execlists: Microoptimise execlists_cancel_port_request()
drm/i915: Don't rmw PIPESTAT enable bits
...
This will allow __drm_mode_object_file to be extended to perform
access control checks based on the file in use.
v2: Also fix up vboxvideo driver in staging
[airlied: merging early as this is an API change]
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The QMUX protocol specification defines structure of the special control
packet messages being sent between handlers of the control port.
Add these to the uapi header, as this structure and the associated types
are shared between the kernel and all userspace handlers of control
messages.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The constants are used by both the name server and clients, so clarify
their value and move them to the uapi header.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no guarantee that either the request or the svc_xprt exist
by the time we get round to printing the trace message.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Yury reported crash with this signature :
[ 554.034021] [<ffff80003ccd5a58>] 0xffff80003ccd5a58
[ 554.034156] [<ffff00000888fd34>] skb_release_all+0x14/0x30
[ 554.034288] [<ffff00000888fd64>] __kfree_skb+0x14/0x28
[ 554.034409] [<ffff0000088ece6c>] tcp_sendmsg_locked+0x4dc/0xcc8
[ 554.034541] [<ffff0000088ed68c>] tcp_sendmsg+0x34/0x58
[ 554.034659] [<ffff000008919fd4>] inet_sendmsg+0x2c/0xf8
[ 554.034783] [<ffff0000088842e8>] sock_sendmsg+0x18/0x30
[ 554.034928] [<ffff0000088861fc>] SyS_sendto+0x84/0xf8
Problem is that skb->destructor contains garbage, and this is
because I accidentally removed tcp_skb_tsorted_anchor_cleanup()
from tcp_unlink_write_queue()
This would trigger with a write(fd, <invalid_memory>, len) attempt,
and we will add to packetdrill this capability to avoid future
regressions.
Fixes: 75c119afe1 ("tcp: implement rb-tree based retransmit queue")
Reported-by: Yury Norov <ynorov@caviumnetworks.com>
Tested-by: Yury Norov <ynorov@caviumnetworks.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* port authorized event for 4-way-HS offload (Avi)
* enable MFP optional for such devices (Emmanuel)
* Kees's timer setup patch for mac80211 mesh
(the part that isn't trivially scripted)
* improve VLAN vs. TXQ handling (myself)
* load regulatory database as firmware file (myself)
* with various other small improvements and cleanups
I merged net-next once in the meantime to allow Kees's
timer setup patch to go in.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEExu3sM/nZ1eRSfR9Ha3t4Rpy0AB0FAlneDzEACgkQa3t4Rpy0
AB3EHBAAhQana6YiMx0Ag4ANGlll3xnxFCZlkmlBoJ/EwKgQhPonylHntuvtkXf6
kZRsOr4uA+wpN/opHLGfMJzat9uxztHVo2sT4rxVnvZq4DYcB/JdlhTMLZDsdDgm
kHRpUEKh/+2FAgq2A4VEUpVb+Mtg0dq8iJJXFw89xb3Sw5UhNA6ljWQZ4zpXuI0P
xOB8Z52LqAcMNnspP+L2TRpanu2ETLcl4Laj+cMl1Yiut2GHkclXUoGvbZ1al5SO
CYqpjVKk67ENLJMrmhQ7DVzj0rpwlV+Eh756RU9DhamPAWbxqWLWJgfuGBskRXnI
GneCUQkLZ5j1kUJjvQdXBv1UmpkCG4/3yITZX8kL3UR+AbhSCqzVQDo7it5hsWEf
XTNAlhdTDhSn7OQQ6XOxvWeydAiaaz671bhPuIvKEo9D/+7Uv0PxHmvu8QqUm0xH
Wvyh0LYRrblDz7fgEkaFctjJKYKnwviQ9O2LGx98C8NVam+Qyti2MlLA4AO5E+it
ky97W3Dh5ftjQhFD0Ip9P4+BO/9hvNELlCRWUXI197n6B0/KH7FWX1eqw/vpnKc4
w7VB/V59mB8zMmZ1QUdwT1/Ru+MD++6ds93STttZvH/0P3H0dDRGuxUK4m32YHiX
s97uSBAbBMy2UH6b8HyxjVMGWvmW3KRakBID1zv2NRSIXtyfWj4=
=gW8q
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Work continues in various areas:
* port authorized event for 4-way-HS offload (Avi)
* enable MFP optional for such devices (Emmanuel)
* Kees's timer setup patch for mac80211 mesh
(the part that isn't trivially scripted)
* improve VLAN vs. TXQ handling (myself)
* load regulatory database as firmware file (myself)
* with various other small improvements and cleanups
I merged net-next once in the meantime to allow Kees's
timer setup patch to go in.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with regards to the return of
FE_SET_PROPERTY. The original idea were to return per-property
return codes via tvp->result field, and to return an updated
set of values.
However, that never worked. What's actually implemented is:
- the FE_SET_PROPERTY implementation doesn't call .get_frontend
callback in order to get the actual parameters after return;
- the tvp->result field is only filled if there's no error.
So, it is always filled with zero;
- FE_SET_PROPERTY doesn't call memdup_user() nor any other
copy_to_user() function. So, any changes to the properties
will be lost;
- FE_SET_PROPERTY is declared as a write-only ioctl (IOW).
While we could fix the above, it could cause regressions.
So, let's just assume what the code really does, updating
the documentation accordingly and removing the logic that
would update the discarded tvp->result.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a keymap for the Sigma Designs Vantage (dev board) remote control.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no users of this functionality (ir-lirc-codec.c has its own
implementation and lirc_zilog.c doesn't use it) so remove it.
This only affects users of the lirc kapi, not rc-core drivers.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pulling the EP validity checks in USB audio drivers.
It also adds a new helper in USB core, which was acked by Greg.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to recent changes for ACPI, the are longer any users of
pm_complete_with_resume_check(), thus let's drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that acpi_dev_runtime_resume() and acpi_dev_resume_early() are
actually literally identical after some more-or-less recent changes,
so rename acpi_dev_runtime_resume() to acpi_dev_resume(), use it
everywhere instead of acpi_dev_resume_early() and drop the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a new helper function to perform a sanity check of the
given URB to see whether it contains a valid endpoint. It's a light-
weight version of what usb_submit_urb() does, but without the kernel
warning followed by the stack trace, just returns an error code.
Especially for a driver that doesn't parse the descriptor but fills
the URB with the fixed endpoint (e.g. some quirks for non-compliant
devices), this kind of check is preferable at the probe phase before
actually submitting the urb.
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case of user unbind ALSA driver during playing back / capturing,
each driver needs to stop and remove it correctly. One note here is
that we can't cancel from remove function in such case, because
unbind operation doesn't check return value from remove function.
So, we *must* stop and remove in this case.
For this purpose, we need to sync (= wait) until the all top-level
operations are canceled at remove function.
For example, snd_card_free() processes the disconnection procedure at
first, then waits for the completion. That's how the hot-unplug works
safely. It's implemented, at least, in the top-level driver removal.
Now for the lower level driver, we need a similar strategy. Notify to
the toplevel for hot-unplug (disconnect in ALSA), and sync with the
stop operation, then continue the rest of its own remove procedure.
This patch adds snd_card_disconnect_sync(), and driver can use it from
remove function.
Note: the "lower level" driver here refers to a middle layer driver
(e.g. ASoC components) that can be unbound freely during operation.
Most of legacy ALSA helper drivers don't have such a problem because
they can't be unbound.
Note#2: snd_card_disconnect_sync() merely calls snd_card_disconnect()
and syncs with closing all pending files. It takes only the files
opened by user-space into account, and doesn't care about object
refcounts. (The latter is handled by snd_card_free() completion call,
BTW.) Also, the function doesn't free resources by itself.
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlnUvBgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AuJB/4u17LCa8PBI7pz0LVr7zwj3AEBZrAb
zq/wqlrqZOhyLEfHtLI/So5LyIFYaF7MZJfylHBp6OiDIXEXzee3qLOc5mQB2jnv
BSnH2Ors658o5TCDm1W0xtHXkujAr7MlaV7Wkaw4lLiq3OeNo8lYMdLVW4tLXf0d
ib7hOsO6idt1H8DRYXlrVrGA7Fz8/m2YYahceAOyLAgLxlepoZGJ1xJxMfqr+ZVs
c85y2JoGWFr0Ac/8E/TZUIuONF4forpaWwI1+/0zCfdNLmG9ceAFxiPPIluAGkeO
EyZzahspaFHa0j+/WrOUlB6YcXPY69pUo89kzHYn7ugBrmGoAMtnLnsN
=BA1X
-----END PGP SIGNATURE-----
Merge tag 'regmap-poll-field' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into drm-misc-next
regmap: Add field polling macro
Requested by Maxime Ripard to make sun4i compile again (next time
the other way round is better).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171004104732.jkps4ufekfizcrkz@sirena.co.uk
MHL specification defines Remote Control Protocol(RCP) to
send input events between MHL devices.
The driver now recognizes RCP messages and reacts to them
by reporting key events to input subsystem, allowing
a user to control a device using TV remote control.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Sean Young <sean@mess.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1503565087-19730-1-git-send-email-m.purski@samsung.com
If the regulatory database is loaded, and then updated, it may
be necessary to reload it. Add an nl80211 command to do this.
Note that this just reloads the database, it doesn't re-apply
the rules from it immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add to the FQ API a way to filter a given tin, in order to
remove frames that fulfil certain criteria according to a
filter function.
This will be used by mac80211 to remove frames belonging to
an AP VLAN interface that's being removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The routine is named incorrectly since the first attempt as there is
nothing like a put_opp() helper. We wanted to unregister the set_opp()
helper here and so it should rather be named as
dev_pm_opp_unregister_set_opp_helper().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds a ct_clear action for clearing conntrack state. ct_clear is
currently implemented in OVS userspace, but is not backed by an action
in the kernel datapath. This is useful for flows that may modify a
packet tuple after a ct lookup has already occurred.
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preempt and irq trace events can be used for tracing the start and
end of an atomic section which can be used by a trace viewer like
systrace to graphically view the start and end of an atomic section and
correlate them with latencies and scheduling issues.
This also serves as a prelude to using synthetic events or probes to
rewrite the preempt and irqsoff tracers, along with numerous benefits of
using trace events features for these events.
Link: http://lkml.kernel.org/r/20171006005432.14244-3-joelaf@google.com
Link: http://lkml.kernel.org/r/20171010225137.17370-1-joelaf@google.com
Cc: Peter Zilstra <peterz@infradead.org>
Cc: kernel-team@android.com
Signed-off-by: Joel Fernandes <joelaf@google.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Fix two issues:
- the per-cpu stat flush is unnecessary, nobody uses per-cpu stat except
sum it to global stat. We can do the calculation there. The flush just
wastes cpu time.
- some fields are signed int/s64. I don't see the point.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
