[ Upstream commit 2d3b55853b ]
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7200f2e3c9 ]
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1f65b0d70 ]
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7fa57ca443 ]
When it's possible that the PF might end up trying to send a
packet to one of its own VFs, we have to forbid IPsec offload
because the device drops the packets into a black hole.
See commit 47b6f50077 ("ixgbe: disallow IPsec Tx offload
when in SR-IOV mode") for more info.
This really is only necessary when the device is in the default
VEB mode. If instead the device is running in VEPA mode,
the packets will go through the encryption engine and out the
MAC/PHY as normal, and get "hairpinned" as needed by the switch.
So let's not block IPsec offload when in VEPA mode. To get
there with the ixgbe device, use the handy 'bridge' command:
bridge link set dev eth1 hwmode vepa
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1066bd193d ]
This patch fixes the following warnings:
- smatch
drivers/net/wireless/quantenna/qtnfmac/commands.c:132 qtnf_cmd_send_with_reply() warn: variable dereferenced before check 'resp' (see line 117)
drivers/net/wireless/quantenna/qtnfmac/commands.c:716 qtnf_cmd_get_sta_info() error: uninitialized symbol 'var_resp_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1668 qtnf_cmd_get_mac_info() error: uninitialized symbol 'var_data_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1697 qtnf_cmd_get_hw_info() error: uninitialized symbol 'info_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1753 qtnf_cmd_band_info_get() error: uninitialized symbol 'info_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1782 qtnf_cmd_send_get_phy_params() error: uninitialized symbol 'response_size'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:2438 qtnf_cmd_get_chan_stats() error: uninitialized symbol 'var_data_len'.
- gcc-8.2.1
drivers/net/wireless/quantenna/qtnfmac/commands.c: In function 'qtnf_cmd_send_with_reply':
drivers/net/wireless/quantenna/qtnfmac/commands.c:133:54: error: 'resp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1492623e83 ]
If an error occurs after the call to 'pci_alloc_irq_vectors()', we must
call 'pci_free_irq_vectors()' in order to avoid a resource leak.
The same sequence is already in place in the corresponding 'cgx_remove()'
function.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3635299183 ]
There are two new Realtek Ethernet devices which are re-branded r8168h.
Add the IDs to to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f87118d576 ]
This patch adds MTU default value to qmap network interface in
order to avoid "RTNETLINK answers: No buffer space available"
error when setting an ipv6 address.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ea89098ef9 ]
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 674bed5df4 ]
When a VLAN is deleted from a bridge port we should not change the PVID
unless the deleted VLAN is the PVID.
Fixes: fe9ccc785d ("mlxsw: spectrum_switchdev: Don't batch VLAN operations")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8adbe212a1 ]
Make sure that lag port TX is disabled before mlxsw_sp_port_lag_leave()
is called and prevent from possible EMAD error.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f1bb6abdf upstream.
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 10262b0b53 ]
Avoid log spam caused by trying to read counters from the chip whilst
it is in a PCI power-save state.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=107421
Fixes: 1ef7286e7f ("r8169: Dereference MMIO address immediately before use")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 001e465f09 ]
A network device stack with multiple layers of bonding devices can
trigger a false positive lockdep warning. Adding lockdep nest levels
fixes this. Update the level on both enslave and unlink, to avoid the
following series of events ..
ip netns add test
ip netns exec test bash
ip link set dev lo addr 00:11:22:33:44:55
ip link set dev lo down
ip link add dev bond1 type bond
ip link add dev bond2 type bond
ip link set dev lo master bond1
ip link set dev bond1 master bond2
ip link set dev bond1 nomaster
ip link set dev bond2 master bond1
.. from still generating a splat:
[ 193.652127] ======================================================
[ 193.658231] WARNING: possible circular locking dependency detected
[ 193.664350] 4.20.0 #8 Not tainted
[ 193.668310] ------------------------------------------------------
[ 193.674417] ip/15577 is trying to acquire lock:
[ 193.678897] 00000000a40e3b69 (&(&bond->stats_lock)->rlock#3/3){+.+.}, at: bond_get_stats+0x58/0x290
[ 193.687851]
but task is already holding lock:
[ 193.693625] 00000000807b9d9f (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0x58/0x290
[..]
[ 193.851092] lock_acquire+0xa7/0x190
[ 193.855138] _raw_spin_lock_nested+0x2d/0x40
[ 193.859878] bond_get_stats+0x58/0x290
[ 193.864093] dev_get_stats+0x5a/0xc0
[ 193.868140] bond_get_stats+0x105/0x290
[ 193.872444] dev_get_stats+0x5a/0xc0
[ 193.876493] rtnl_fill_stats+0x40/0x130
[ 193.880797] rtnl_fill_ifinfo+0x6c5/0xdc0
[ 193.885271] rtmsg_ifinfo_build_skb+0x86/0xe0
[ 193.890091] rtnetlink_event+0x5b/0xa0
[ 193.894320] raw_notifier_call_chain+0x43/0x60
[ 193.899225] netdev_change_features+0x50/0xa0
[ 193.904044] bond_compute_features.isra.46+0x1ab/0x270
[ 193.909640] bond_enslave+0x141d/0x15b0
[ 193.913946] do_set_master+0x89/0xa0
[ 193.918016] do_setlink+0x37c/0xda0
[ 193.921980] __rtnl_newlink+0x499/0x890
[ 193.926281] rtnl_newlink+0x48/0x70
[ 193.930238] rtnetlink_rcv_msg+0x171/0x4b0
[ 193.934801] netlink_rcv_skb+0xd1/0x110
[ 193.939103] rtnetlink_rcv+0x15/0x20
[ 193.943151] netlink_unicast+0x3b5/0x520
[ 193.947544] netlink_sendmsg+0x2fd/0x3f0
[ 193.951942] sock_sendmsg+0x38/0x50
[ 193.955899] ___sys_sendmsg+0x2ba/0x2d0
[ 193.960205] __x64_sys_sendmsg+0xad/0x100
[ 193.964687] do_syscall_64+0x5a/0x460
[ 193.968823] entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 7e2556e400 ("bonding: avoid lockdep confusion in bond_get_stats()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 11287b693d ]
This soft dependency works around an issue where sometimes the genphy
driver is used instead of the dedicated PHY driver. The root cause of
the issue isn't clear yet. People reported the unloading/re-loading
module r8169 helps, and also configuring this soft dependency in
the modprobe config files. Important just seems to be that the
realtek module is loaded before r8169.
Once this has been applied preliminary fix 38af4b9032 ("net: phy:
add workaround for issue where PHY driver doesn't bind to the device")
will be removed.
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0071840d2 ]
It has been noticed that some phys do not have the registers
required by the previous implementation.
To fix this, instead of using phy_read, the required information
is extracted from the phy_device structure.
fixes: 23f0703c12 ("lan743x: Add main source files for new lan743x driver")
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f2f98c1d7f ]
Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9e857a40dc ]
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40f89ebfbd ]
The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b7959b625 ]
BUG: unable to handle kernel NULL pointer dereference at 00000000000000d1
Call Trace:
? napi_gro_frags+0xa7/0x2c0
tun_get_user+0xb50/0xf20
tun_chr_write_iter+0x53/0x70
new_sync_write+0xff/0x160
vfs_write+0x191/0x1e0
__x64_sys_write+0x5e/0xd0
do_syscall_64+0x47/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
I think there is a subtle race between sending a packet via tap and
attaching it:
CPU0: CPU1:
tun_chr_ioctl(TUNSETIFF)
tun_set_iff
tun_attach
rcu_assign_pointer(tfile->tun, tun);
tun_fops->write_iter()
tun_chr_write_iter
tun_napi_alloc_frags
napi_get_frags
napi->skb = napi_alloc_skb
tun_napi_init
netif_napi_add
napi->skb = NULL
napi->skb is NULL here
napi_gro_frags
napi_frags_skb
skb = napi->skb
skb_reset_mac_header(skb)
panic()
Move rcu_assign_pointer(tfile->tun) and rcu_assign_pointer(tun->tfiles) to
be the last thing we do in tun_attach(); this should guarantee that when we
call tun_get() we always get an initialized object.
v2 changes:
* remove extra napi_mutex locks/unlocks for napi operations
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ea3819c0b upstream.
The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a9f ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.
This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.
Fixes: 9865045403 ("b43: make cordic common (LP-PHY and N-PHY need it)")
Reported-by: Priit Laes <plaes@plaes.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> # 2.6.34
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b72c51a58e upstream.
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee2 ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c892df415 upstream.
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5c7c745f2 ]
When x25_asy_open() fails, it already cleans up by itself,
so its caller doesn't need to free the memory again.
It seems we still have to call x25_asy_free() to clear the SLF_INUSE
bit, so just set these pointers to NULL after kfree().
Reported-and-tested-by: syzbot+5e5e969e525129229052@syzkaller.appspotmail.com
Fixes: 3b780bed31 ("x25_asy: Free x25_asy on x25_asy_open() failure.")
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 756af9c642 ]
Commit 33a48ab105 ("ibmveth: Fix DMA unmap error") fixed an issue in the
normal code path of ibmveth_xmit_start() that was originally introduced by
Commit 6e8ab30ec6 ("ibmveth: Add scatter-gather support"). This original
fix missed the error path where dma_unmap_page is wrongly called on the
header portion in descs[0] which was mapped with dma_map_single. As a
result a failure to DMA map any of the frags results in a dmesg warning
when CONFIG_DMA_API_DEBUG is enabled.
------------[ cut here ]------------
DMA-API: ibmveth 30000002: device driver frees DMA memory with wrong function
[device address=0x000000000a430000] [size=172 bytes] [mapped as page] [unmapped as single]
WARNING: CPU: 1 PID: 8426 at kernel/dma/debug.c:1085 check_unmap+0x4fc/0xe10
...
<snip>
...
DMA-API: Mapped at:
ibmveth_start_xmit+0x30c/0xb60
dev_hard_start_xmit+0x100/0x450
sch_direct_xmit+0x224/0x490
__qdisc_run+0x20c/0x980
__dev_queue_xmit+0x1bc/0xf20
This fixes the API misuse by unampping descs[0] with dma_unmap_single.
Fixes: 6e8ab30ec6 ("ibmveth: Add scatter-gather support")
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c76e77f90 ]
The BPF flow dissector expects either skb->sk or skb->dev set on
all skbs. Delay flow dissection until after skb->dev is set.
This requires calling from within an rcu read-side critical section.
That is fine, see also the call from tun_xdp_one.
Fixes: d0e13a1488 ("flow_dissector: lookup netns by skb->sk if skb->dev is NULL")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38355a5f9a ]
This happened when I tried to boot normal Fedora 29 system with latest
available kernel (from fedora rawhide, plus some unrelated custom
patches):
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
PGD 0 P4D 0
Oops: 0010 [#1] SMP PTI
CPU: 6 PID: 1422 Comm: libvirtd Tainted: G I 4.20.0-0.rc7.git3.hpsa2.1.fc29.x86_64 #1
Hardware name: HP ProLiant BL460c G6, BIOS I24 05/21/2018
RIP: 0010: (null)
Code: Bad RIP value.
RSP: 0018:ffffa47ccdc9fbe0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00000000000003e8 RCX: ffffa47ccdc9fbf8
RDX: ffffa47ccdc9fc00 RSI: ffff97d9ee7b01f8 RDI: ffff97d9f0150b80
RBP: ffff97d9f0150b80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000003
R13: ffff97d9ef1e53e8 R14: 0000000000000009 R15: ffff97d9f0ac6730
FS: 00007f4d224ef700(0000) GS:ffff97d9fa200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 00000011ece52006 CR4: 00000000000206e0
Call Trace:
? bnx2x_chip_cleanup+0x195/0x610 [bnx2x]
? bnx2x_nic_unload+0x1e2/0x8f0 [bnx2x]
? bnx2x_reload_if_running+0x24/0x40 [bnx2x]
? bnx2x_set_features+0x79/0xa0 [bnx2x]
? __netdev_update_features+0x244/0x9e0
? netlink_broadcast_filtered+0x136/0x4b0
? netdev_update_features+0x22/0x60
? dev_disable_lro+0x1c/0xe0
? devinet_sysctl_forward+0x1c6/0x211
? proc_sys_call_handler+0xab/0x100
? __vfs_write+0x36/0x1a0
? rcu_read_lock_sched_held+0x79/0x80
? rcu_sync_lockdep_assert+0x2e/0x60
? __sb_start_write+0x14c/0x1b0
? vfs_write+0x159/0x1c0
? vfs_write+0xba/0x1c0
? ksys_write+0x52/0xc0
? do_syscall_64+0x60/0x1f0
? entry_SYSCALL_64_after_hwframe+0x49/0xbe
After some investigation I figured out that recently added cleanup code
tries to call VLAN filtering de-initialization function which exist only
for newer hardware. Corresponding function pointer is not
set (== 0) for older hardware, namely these chips:
#define CHIP_NUM_57710 0x164e
#define CHIP_NUM_57711 0x164f
#define CHIP_NUM_57711E 0x1650
And I have one of those in my test system:
Broadcom Inc. and subsidiaries NetXtreme II BCM57711E 10-Gigabit PCIe [14e4:1650]
Function bnx2x_init_vlan_mac_fp_objs() from
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h decides whether to
initialize relevant pointers in bnx2x_sp_objs.vlan_obj or not.
This regression was introduced after v4.20-rc7, and still exists in v4.20
release.
Fixes: 04f05230c5 ("bnx2x: Remove configured vlans as part of unload sequence.")
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Signed-off-by: Ivan Mironov <mironov.ivan@gmail.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes qmap header retrieval when modem is configured for
dl data aggregation.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Fibocom NL678 series cellular module QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netxen_rom_fast_read() fails, "bios" is left uninitialized and may
contain random value, thus should not be used.
The fix ensures that if netxen_rom_fast_read() fails, we return "-EIO".
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC table in Ocelot supports auto aging (normal) and static entries.
MAC entries that is manually configured should be static and not subject
to aging.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Allan Nielsen <allan.nielsen@microchip.com>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.
There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.
Fixes: bd5251dbf1 ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc9925 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.
Fixes: e44758b78a ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcGlNvAAoJEG4XJFUm622boJ0H/AjDASkdxSG4n+s1wCmsUizE
jK9YwS2dOc1oVSzGPm35GccFgkc4x1IpS1qoTo1rykVD7Cn6G7mj6eqy8vTiJ24S
6HPhdkS5YynWvYfbQmuhhhaQ6ew8/dJzqhPJAH1/kPfDsy08qUaVl5tGw4CwP4Pp
Ufvrn8VNmRbrAg9Jq28+xmANNURtKNtHmXI5WWuSvA4LzkdEz2aebG8ynOwTrVW6
f6NHTDeJ5tWrswr0EWGjBbGRfb8TlacOxqzytrFYFuYHH3WiqCQZdsvRBazvryqJ
szrYMlI+bSN4m3ZEAtEWlZYTU1YNPwbRDXc+GYkbDr19YKevHxi+46SvXa36cJM=
=ECaW
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.20
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd ("vxge: serialize access to steering control register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe117333 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
