Add lane_polarities field to struct v4l2_of_bus_mipi_csi2 and write the
contents of the lane-polarities property to it. The field tells the polarity
of the physical lanes starting from the first one. Any unused lanes are
ignored, i.e. only the polarity of the used lanes is specified.
Also rework reading the "data-lanes" property a little.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video port clock is l3_ick divided by vpclk_div. This clock must be high
enough for the external pixel rate. The video port requires two clock cycles
to process a pixel.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make omap3isp configuration data structures more suitable for consumption by
the DT by separating the I2C bus information of all the sub-devices in a
group and the ISP bus information from each other. The ISP bus information
is made a pointer instead of being directly embedded in the struct.
In the case of the DT only the sensor specific information on the ISP bus
configuration is retained. The structs are renamed to reflect that.
After this change the structs needed to describe device configuration can be
allocated and accessed separately without those needed only in the case of
platform data. The platform data related structs can be later removed once
the support for platform data can be removed.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Igor Grinberg <grinberg@compulab.co.il> (for cm-t35)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The header is not included anywhere. Remove it and include the private
nbd_device struct in nbd.c.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull networking fixes from David Miller:
1) Fix use-after-free with mac80211 RX A-MPDU reorder timer, from
Johannes Berg.
2) iwlwifi leaks memory every module load/unload cycles, fix from Larry
Finger.
3) Need to use for_each_netdev_safe() in rtnl_group_changelink()
otherwise we can crash, from WANG Cong.
4) mlx4 driver does register_netdev() too early in the probe sequence,
from Ido Shamay.
5) Don't allow router discovery hop limit to decrease the interface's
hop limit, from D.S. Ljungmark.
6) tx_packets and tx_bytes improperly accounted for certain classes of
USB network devices, fix from Ben Hutchings.
7) ip{6}mr_rules_init() mistakenly use plain kfree to release the ipmr
tables in the error path, they must instead use ip{6}mr_free_table().
Fix from WANG Cong.
8) cxgb4 doesn't properly quiesce all RX activity before unregistering
the netdevice. Fix from Hariprasad Shenai.
9) Fix hash corruptions in ipvlan driver, from Jiri Benc.
10) nla_memcpy(), like a real memcpy, should fully initialize the
destination buffer, even if the source attribute is smaller. Fix
from Jiri Benc.
11) Fix wrong error code returned from iucv_sock_sendmsg(). We should
use whatever sock_alloc_send_skb() put into 'err'. From Eugene
Crosser.
12) Fix slab object leak on module unload in TIPC, from Ying Xue.
13) Need a READ_ONCE() when reading the cached RX socket route in
tcp_v{4,6}_early_demux(). From Michal Kubecek.
14) Still too many problems with TPC support in the ath9k driver, so
disable it for now. From Felix Fietkau.
15) When in AP mode the rtlwifi driver can leak DMA mappings, fix from
Larry Finger.
16) Missing kzalloc() failure check in gs_usb CAN driver, from Colin Ian
King.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
cxgb4: Fix to dump devlog, even if FW is crashed
cxgb4: Firmware macro changes for fw verison 1.13.32.0
bnx2x: Fix kdump when iommu=on
bnx2x: Fix kdump on 4-port device
mac80211: fix RX A-MPDU session reorder timer deletion
MAINTAINERS: Update Intel Wired Ethernet Driver info
tipc: fix a slab object leak
net/usb/r8152: add device id for Lenovo TP USB 3.0 Ethernet
af_iucv: fix AF_IUCV sendmsg() errno
openvswitch: Return vport module ref before destruction
netlink: pad nla_memcpy dest buffer with zeroes
bonding: Bonding Overriding Configuration logic restored.
ipvlan: fix check for IP addresses in control path
ipvlan: do not use rcu operations for address list
ipvlan: protect against concurrent link removal
ipvlan: fix addr hash list corruption
net: fec: setup right value for mdio hold time
net: tcp6: fix double call of tcp_v6_fill_cb()
cxgb4vf: Fix sparse warnings
netns: don't clear nsid too early on removal
...
Now that all users of iflink have the ndo_get_iflink handler available, it's
possible to remove this field.
By default, dev_get_iflink() returns the ifindex of the interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many panel data sheets, additionally to typical values, list allowed
ranges for timings such as hsync/vsync lengths, porches, and the pixel
clock rate. These can be stored in a struct display_timing, to be used
by an encoder mode_fixup callback to clamp user provided timing values
or to validate workarounds for clock source limitations.
This patch adds a new drm_panel_funcs callback that returns the panel's
available display_timing entries.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On 64-bit targets, tegra_gem_mmap() only returns a partial offset to
userspace. As such, subsequent calls to mmap(2) may fail. Change the
arguments to use a 64-bit offset to fix this.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Erik Faye-Lund <kusmabite@gmail.com>
[treding@nvidia.com: tweak commit message]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Drivers that subclass CRTC, plane or connector state need to carefully
duplicate the code that the atomic helpers have. This is bound to cause
breakage eventually because it requires auditing all drivers and update
them when code is added to the helpers.
In order to avoid that, implement new helpers that perform the required
steps when copying and destroying state. These new helpers are exported
so that state-subclassing drivers can use them. The default helpers are
implemented using them as well, providing a single location that needs
to be changed when adding to base atomic states.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This function is used to read the current value of the syncpt and is
useful in situations where drivers don't schedule work and wait for the
syncpoint to increment. One particular use-case is using the syncpoint
as a VBLANK counter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds two new functions to enable/disable
the watchdog across all CPUs.
This will be used by the HT PMU bug workaround code to
disable/enable the NMI watchdog across quirk enablement.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: bp@alien8.de
Cc: jolsa@redhat.com
Cc: kan.liang@intel.com
Cc: maria.n.dimakopoulou@gmail.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1416251225-17721-12-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For counters that generate AUX data that is bound to the context of a
running task, such as instruction tracing, the decoder needs to know
exactly which task is running when the event is first scheduled in,
before the first sched_switch. The decoder's need to know this stems
from the fact that instruction flow trace decoding will almost always
require program's object code in order to reconstruct said flow and
for that we need at least its pid/tid in the perf stream.
To single out such instruction tracing pmus, this patch introduces
ITRACE PMU capability. The reason this is not part of RECORD_AUX
record is that not all pmus capable of generating AUX data need this,
and the opposite is *probably* also true.
While sched_switch covers for most cases, there are two problems with it:
the consumer will need to process events out of order (that is, having
found RECORD_AUX, it will have to skip forward to the nearest sched_switch
to figure out which task it was, then go back to the actual trace to
decode it) and it completely misses the case when the tracing is enabled
and disabled before sched_switch, for example, via PERF_EVENT_IOC_DISABLE.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-15-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When AUX area gets a certain amount of new data, we want to wake up
userspace to collect it. This adds a new control to specify how much
data will cause a wakeup. This is then passed down to pmu drivers via
output handle's "wakeup" field, so that the driver can find the nearest
point where it can generate an interrupt.
We repurpose __reserved_2 in the event attribute for this, even though
it was never checked to be zero before, aux_watermark will only matter
for new AUX-aware code, so the old code should still be fine.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-10-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds support for overwrite mode in the AUX area, which means "keep
collecting data till you're stopped", turning AUX area into a circular
buffer, where new data overwrites old data. It does not depend on data
buffer's overwrite mode, so that it doesn't lose sideband data that is
instrumental for processing AUX data.
Overwrite mode is enabled at mapping AUX area read only. Even though
aux_tail in the buffer's user page might be user writable, it will be
ignored in this mode.
A PERF_RECORD_AUX with PERF_AUX_FLAG_OVERWRITE set is written to the perf
data stream every time an event writes new data to the AUX area. The pmu
driver might not be able to infer the exact beginning of the new data in
each snapshot, some drivers will only provide the tail, which is
aux_offset + aux_size in the AUX record. Consumer has to be able to tell
the new data from the old one, for example, by means of time stamps if
such are provided in the trace.
Consumer is also responsible for disabling any events that might write
to the AUX area (thus potentially racing with the consumer) before
collecting the data.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-9-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For pmus that wish to write data to ring buffer's AUX area, provide
perf_aux_output_{begin,end}() calls to initiate/commit data writes,
similarly to perf_output_{begin,end}. These also use the same output
handle structure. Also, similarly to software counterparts, these
will direct inherited events' output to parents' ring buffers.
After the perf_aux_output_begin() returns successfully, handle->size
is set to the maximum amount of data that can be written wrt aux_tail
pointer, so that no data that the user hasn't seen will be overwritten,
therefore this should always be called before hardware writing is
enabled. On success, this will return the pointer to pmu driver's
private structure allocated for this aux area by pmu::setup_aux. Same
pointer can also be retrieved using perf_get_aux() while hardware
writing is enabled.
PMU driver should pass the actual amount of data written as a parameter
to perf_aux_output_end(). All hardware writes should be completed and
visible before this one is called.
Additionally, perf_aux_output_skip() will adjust output handle and
aux_head in case some part of the buffer has to be skipped over to
maintain hardware's alignment constraints.
Nested writers are forbidden and guards are in place to catch such
attempts.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-8-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When there's new data in the AUX space, output a record indicating its
offset and size and a set of flags, such as PERF_AUX_FLAG_TRUNCATED, to
mean the described data was truncated to fit in the ring buffer.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-7-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Usually, pmus that do, for example, instruction tracing, would only ever
be able to have one event per task per cpu (or per perf_event_context). For
such pmus it makes sense to disallow creating conflicting events early on,
so as to provide consistent behavior for the user.
This patch adds a pmu capability that indicates such constraint on event
creation.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1422613866-113186-1-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For pmus that don't support scatter-gather for AUX data in hardware, it
might still make sense to implement software double buffering to avoid
losing data while the user is reading data out. For this purpose, add
a pmu capability that guarantees multiple high-order chunks for AUX buffer,
so that the pmu driver can do switchover tricks.
To make use of this feature, add PERF_PMU_CAP_AUX_SW_DOUBLEBUF to your
pmu's capability mask. This will make the ring buffer AUX allocation code
ensure that the biggest high order allocation for the aux buffer pages is
no bigger than half of the total requested buffer size, thus making sure
that the buffer has at least two high order allocations.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-5-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some pmus (such as BTS or Intel PT without multiple-entry ToPA capability)
don't support scatter-gather and will prefer larger contiguous areas for
their output regions.
This patch adds a new pmu capability to request higher order allocations.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-4-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces "AUX space" in the perf mmap buffer, intended for
exporting high bandwidth data streams to userspace, such as instruction
flow traces.
AUX space is a ring buffer, defined by aux_{offset,size} fields in the
user_page structure, and read/write pointers aux_{head,tail}, which abide
by the same rules as data_* counterparts of the main perf buffer.
In order to allocate/mmap AUX, userspace needs to set up aux_offset to
such an offset that will be greater than data_offset+data_size and
aux_size to be the desired buffer size. Both need to be page aligned.
Then, same aux_offset and aux_size should be passed to mmap() call and
if everything adds up, you should have an AUX buffer as a result.
Pages that are mapped into this buffer also come out of user's mlock
rlimit plus perf_event_mlock_kb allowance.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-3-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently, the actual perf ring buffer is one page into the mmap area,
following the user page and the userspace follows this convention. This
patch adds data_{offset,size} fields to user_page that can be used by
userspace instead for locating perf data in the mmap area. This is also
helpful when mapping existing or shared buffers if their size is not
known in advance.
Right now, it is made to follow the existing convention that
data_offset == PAGE_SIZE and
data_offset + data_size == mmap_size.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kaixu Xia <kaixu.xia@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@infradead.org
Cc: adrian.hunter@intel.com
Cc: kan.liang@intel.com
Cc: markus.t.metzger@intel.com
Cc: mathieu.poirier@linaro.org
Link: http://lkml.kernel.org/r/1421237903-181015-2-git-send-email-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that there's a HCI request API available where the callback receives
the resulting skb, we can convert the local OOB data reading to use this
new API. This patch does the necessary update in mgmt.c (which also
requires moving the callback higher up since it's now a static function)
and removes the custom calls from hci_event.c that are no-longer
necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_req_pending() function has no users anymore, so simply remove
it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the synchronous HCI requests use the new API and a new private
variable the recv_evt member of hci_dev is no-longer needed. This patch
removes it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there's an API in place that allows passing the resulting skb
to the request callback we can conveniently convert the hci_req_sync and
related functions to use it. Since we still need to get the skb from the
async callback into the sleeping _sync() function the patch adds another
req_skb variable to hci_dev where the sync request state is tracked.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a second possible callback for HCI requests where the
callback will receive the full skb of the last successfully completed
HCI command. This API is useful for cases where we want to use a request
to read some data and the existing hci_event.c handlers do not store it
e.g. in the hci_dev struct.
The reason the patch is a bit bigger than just adding the new API is
because the hci_req_cmd_complete() functions required some refactoring
to enable it: now hci_req_cmd_complete() is simply used to request the
callback pointers if any, and the actual calling of them happens from a
single place at the end of hci_event_packet(). The reason for this is
that we need to pass the original skb (without any skb_pull, etc
modifications done to it) and it's simplest to keep track of it within
the hci_event_packet() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the retrieval operation may be disposed of by fscache_put_operation()
before we actually set the context, the retrieval-specific cleanup operation
can produce a NULL-pointer dereference when it tries to unconditionally clean
up the netfs context.
Given that it is expected that we'll get at least as far as the place where we
currently set the context pointer and it is unlikely we'll go through the
error handling paths prior to that point, retain the context right from the
point that the retrieval op is allocated.
Concomitant to this, we need to retain the cookie pointer in the retrieval op
also so that we can call the netfs to release its context in the release
method.
In addition, we might now get into fscache_release_retrieval_op() with the op
only initialised. To this end, set the operation to DEAD only after the
release method has been called and skip the n_pages test upon cleanup if the
op is still in the INITIALISED state.
Without these changes, the following oops might be seen:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000b8
...
RIP: 0010:[<ffffffffa0089c98>] fscache_release_retrieval_op+0xae/0x100
...
Call Trace:
[<ffffffffa0088560>] fscache_put_operation+0x117/0x2e0
[<ffffffffa008b8f5>] __fscache_read_or_alloc_pages+0x351/0x3ac
[<ffffffffa00b761f>] __nfs_readpages_from_fscache+0x59/0xbf [nfs]
[<ffffffffa00b06c5>] nfs_readpages+0x10c/0x185 [nfs]
[<ffffffff81124925>] ? alloc_pages_current+0x119/0x13e
[<ffffffff810ee5fd>] ? __page_cache_alloc+0xfb/0x10a
[<ffffffff810f87f8>] __do_page_cache_readahead+0x188/0x22c
[<ffffffff810f8b3a>] ondemand_readahead+0x29e/0x2af
[<ffffffff810f8c92>] page_cache_sync_readahead+0x38/0x3a
[<ffffffff810ef337>] generic_file_read_iter+0x1a2/0x55a
[<ffffffffa00a9dff>] ? nfs_revalidate_mapping+0xd6/0x288 [nfs]
[<ffffffffa00a6a23>] nfs_file_read+0x49/0x70 [nfs]
[<ffffffff811363be>] new_sync_read+0x78/0x9c
[<ffffffff81137164>] __vfs_read+0x13/0x38
[<ffffffff8113721e>] vfs_read+0x95/0x121
[<ffffffff811372f6>] SyS_read+0x4c/0x8a
[<ffffffff81557a52>] system_call_fastpath+0x12/0x17
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jeff.layton@primarydata.com>
Any time an incomplete operation is cancelled, the operation cancellation
function needs to be called to clean up. This is currently being passed
directly to some of the functions that might want to call it, but not all.
Instead, pass the cancellation method pointer to the fscache_operation_init()
and have that cache it in the operation struct. Further, plug in a dummy
cancellation handler if the caller declines to set one as this allows us to
call the function unconditionally (the extra overhead isn't worth bothering
about as we don't expect to be calling this typically).
The cancellation method must thence be called everywhere the CANCELLED state
is set. Note that we call it *before* setting the CANCELLED state such that
the method can use the old state value to guide its operation.
fscache_do_cancel_retrieval() needs moving higher up in the sources so that
the init function can use it now.
Without this, the following oops may be seen:
FS-Cache: Assertion failed
FS-Cache: 3 == 0 is false
------------[ cut here ]------------
kernel BUG at ../fs/fscache/page.c:261!
...
RIP: 0010:[<ffffffffa0089c1b>] fscache_release_retrieval_op+0x77/0x100
[<ffffffffa008853d>] fscache_put_operation+0x114/0x2da
[<ffffffffa008b8c2>] __fscache_read_or_alloc_pages+0x358/0x3b3
[<ffffffffa00b761f>] __nfs_readpages_from_fscache+0x59/0xbf [nfs]
[<ffffffffa00b06c5>] nfs_readpages+0x10c/0x185 [nfs]
[<ffffffff81124925>] ? alloc_pages_current+0x119/0x13e
[<ffffffff810ee5fd>] ? __page_cache_alloc+0xfb/0x10a
[<ffffffff810f87f8>] __do_page_cache_readahead+0x188/0x22c
[<ffffffff810f8b3a>] ondemand_readahead+0x29e/0x2af
[<ffffffff810f8c92>] page_cache_sync_readahead+0x38/0x3a
[<ffffffff810ef337>] generic_file_read_iter+0x1a2/0x55a
[<ffffffffa00a9dff>] ? nfs_revalidate_mapping+0xd6/0x288 [nfs]
[<ffffffffa00a6a23>] nfs_file_read+0x49/0x70 [nfs]
[<ffffffff811363be>] new_sync_read+0x78/0x9c
[<ffffffff81137164>] __vfs_read+0x13/0x38
[<ffffffff8113721e>] vfs_read+0x95/0x121
[<ffffffff811372f6>] SyS_read+0x4c/0x8a
[<ffffffff81557a52>] system_call_fastpath+0x12/0x17
The assertion is showing that the remaining number of pages (n_pages) is not 0
when the operation is being released.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jeff.layton@primarydata.com>
Out of line fscache_operation_init() so that it can access internal FS-Cache
features, such as stats, in a later commit.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jeff.layton@primarydata.com>
fscache_object_is_dead() returns true only if the object is marked dead and
the cache got an I/O error. This should be a logical OR instead. Since two
of the callers got split up into handling for separate subcases, expand the
other callers and kill the function. This is probably the right thing to do
anyway since one of the subcases isn't about the object at all, but rather
about the cache.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jeff.layton@primarydata.com>
When submitting an operation, prefer to cancel the operation immediately
rather than queuing it for later processing if the object is marked as dying
(ie. the object state machine has reached the KILL_OBJECT state).
Whilst we're at it, change the series of related test_bit() calls into a
READ_ONCE() and bitwise-AND operators to reduce the number of load
instructions (test_bit() has a volatile address).
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steve Dickson <steved@redhat.com>
Acked-by: Jeff Layton <jeff.layton@primarydata.com>
It was found when doing a hotplug stress test on POWER, that the
machine either hit softlockups or rcu_sched stall warnings. The
issue was traced to commit:
7cba160ad7 ("powernv/cpuidle: Redesign idle states management")
which exposed the cpu_down() race with hrtimer based broadcast mode:
5d1638acb9 ("tick: Introduce hrtimer based broadcast")
The race is the following:
Assume CPU1 is the CPU which holds the hrtimer broadcasting duty
before it is taken down.
CPU0 CPU1
cpu_down() take_cpu_down()
disable_interrupts()
cpu_die()
while (CPU1 != CPU_DEAD) {
msleep(100);
switch_to_idle();
stop_cpu_timer();
schedule_broadcast();
}
tick_cleanup_cpu_dead()
take_over_broadcast()
So after CPU1 disabled interrupts it cannot handle the broadcast
hrtimer anymore, so CPU0 will be stuck forever.
Fix this by explicitly taking over broadcast duty before cpu_die().
This is a temporary workaround. What we really want is a callback
in the clockevent device which allows us to do that from the dying
CPU by pushing the hrtimer onto a different cpu. That might involve
an IPI and is definitely more complex than this immediate fix.
Changelog was picked up from:
https://lkml.org/lkml/2015/2/16/213
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: mpe@ellerman.id.au
Cc: nicolas.pitre@linaro.org
Cc: peterz@infradead.org
Cc: rjw@rjwysocki.net
Fixes: http://linuxppc.10917.n7.nabble.com/offlining-cpus-breakage-td88619.html
Link: http://lkml.kernel.org/r/20150330092410.24979.59887.stgit@preeti.in.ibm.com
[ Merged it to the latest timer tree, renamed the callback, tidied up the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Debugging of BPF programs needs some form of printk from the
program, so let programs call limited trace_printk() with %d %u
%x %p modifiers only.
Similar to kernel modules, during program load verifier checks
whether program is calling bpf_trace_printk() and if so, kernel
allocates trace_printk buffers and emits big 'this is debug
only' banner.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-6-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bpf_ktime_get_ns() is used by programs to compute time delta
between events or as a timestamp
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-5-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
BPF programs, attached to kprobes, provide a safe way to execute
user-defined BPF byte-code programs without being able to crash or
hang the kernel in any way. The BPF engine makes sure that such
programs have a finite execution time and that they cannot break
out of their sandbox.
The user interface is to attach to a kprobe via the perf syscall:
struct perf_event_attr attr = {
.type = PERF_TYPE_TRACEPOINT,
.config = event_id,
...
};
event_fd = perf_event_open(&attr,...);
ioctl(event_fd, PERF_EVENT_IOC_SET_BPF, prog_fd);
'prog_fd' is a file descriptor associated with BPF program
previously loaded.
'event_id' is an ID of the kprobe created.
Closing 'event_fd':
close(event_fd);
... automatically detaches BPF program from it.
BPF programs can call in-kernel helper functions to:
- lookup/update/delete elements in maps
- probe_read - wraper of probe_kernel_read() used to access any
kernel data structures
BPF programs receive 'struct pt_regs *' as an input ('struct pt_regs' is
architecture dependent) and return 0 to ignore the event and 1 to store
kprobe event into the ring buffer.
Note, kprobes are a fundamentally _not_ a stable kernel ABI,
so BPF programs attached to kprobes must be recompiled for
every kernel version and user must supply correct LINUX_VERSION_CODE
in attr.kern_version during bpf_prog_load() call.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-4-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
add TRACE_EVENT_FL_KPROBE flag to differentiate kprobe type of
tracepoints, since bpf programs can only be attached to kprobe
type of PERF_TYPE_TRACEPOINT perf events.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1427312966-8434-3-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Socket filter code and other subsystems with upcoming eBPF
support should not need to deal with the fact that we have
CONFIG_BPF_SYSCALL defined or not.
Having the bpf syscall as a config option is a nice thing and
I'd expect it to stay that way for expert users (I presume one
day the default setting of it might change, though), but code
making use of it should not care if it's actually enabled or
not.
Instead, hide this via header files and let the rest deal with it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1427312966-8434-2-git-send-email-ast@plumgrid.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Do various cleanups on the clockchips.h file:
- indent preprocessor blocks to make it more clear which block we are in,
this also makes merge resolution easier
- comment larger preprocessor blocks consistently, using the:
#if FOO
...
#else /* !FOO: */
...
#endif /* !FOO */
notation.
- unbreak lines
- etc.
No change in functionality.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- reworked arch/arm/mach-at91/Kconfig and arch/arm/Kconfig to switch to
multi-platform
- updated at91_dt_defconfig
- continue the cleanup of unneeded files and code chunks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVCv+EAAoJEAf03oE53VmQRgQIALCEppiZCt7xzH8bbGToyiSh
A1lWqDFm5kvkUW9igaks1XenxcDmKg7TwLfjolyqny20CL6/rt1oap07Yt7eAIW1
6KdCKk7RML0vduX3F/wl+ZQe6ykob0vWzaeeUNI1RgBkD7hsZCb60Re1fj44pR99
dgj08EAme1yBvvFN2iA7IWUXJMPIuQ+uFzFUMiPVahgR49AbTG/TLfGHWM8i/H15
HF/ETeShV4k02lqipm4E8te0VAiDjYcrpc12NbQ0M1jFgD+1V+tY0IvrrtTcxHEe
53CCwN09nKJTRBZrPyCdKK7r4xrpPb64ZydBWXOHkVizS24jG1fc4aXG74qBooI=
=uyvg
-----END PGP SIGNATURE-----
Merge tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/multiplatform
Merge "at91: multiplatform for 4.1 #1" from Nicolas Ferre:
This is the multi-platform support for AT91:
- reworked arch/arm/mach-at91/Kconfig and arch/arm/Kconfig to switch to
multi-platform
- updated at91_dt_defconfig
- continue the cleanup of unneeded files and code chunks
* tag 'at91-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91: (61 commits)
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Merged the based Qualcomm SCM and SCM boot support
* Cleaned up SCM interface to only expose functional SCM APIs
* Moved Qualcomm SCM code into drivers/firmware
* Updated the SCM APIs for setting cpu cold and warm boot addresses
* Added support for ADM CRCI muxing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=KYay
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/drivers
Merge "qcom SoC changes for v4.1" from Kumar Gala:
Qualcomm ARM Based SoC Updates for v4.1
* Merged the based Qualcomm SCM and SCM boot support
* Cleaned up SCM interface to only expose functional SCM APIs
* Moved Qualcomm SCM code into drivers/firmware
* Updated the SCM APIs for setting cpu cold and warm boot addresses
* Added support for ADM CRCI muxing
* tag 'qcom-soc-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
soc: qcom: gsbi: Add support for ADM CRCI muxing
firmware: qcom: scm: Support cpu power down through SCM
firmware: qcom: scm: Add qcom_scm_set_warm_boot_addr function
firmware: qcom: scm: Clean cold boot entry to export only the API
firmware: qcom: scm: Move the scm driver to drivers/firmware
ARM: qcom: Prep scm code for move to drivers/firmware
ARM: qcom: Cleanup scm interface to only export what is needed
ARM: qcom: Merge scm and scm boot code together
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add multiplatform support to sh73a0 and its kzm9g board
* Use Bus State Controller to enable ethernet for multiplatform sh73a0/kzm9g
* Add PM domain support to multiplatform sh73a0
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7DUP
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Merge "Renesas ARM Based SoC sh73a0 Multiplatform Updates for v4.1" from Simon
Horman:
* Add multiplatform support to sh73a0 and its kzm9g board
* Use Bus State Controller to enable ethernet for multiplatform sh73a0/kzm9g
* Add PM domain support to multiplatform sh73a0
* tag 'renesas-sh73a0-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
ARM: shmobile: sh73a0: Remove restart callback
ARM: shmobile: sh73a0 dtsi: Add PM domain support
ARM: shmobile: sh73a0: Remove unused sh73a0_add_standard_devices_dt()
ARM: shmobile: sh73a0 dtsi: Add Cortex-A9 TWD node
ARM: shmobile: kzm9g-reference: Remove board C code and DT file
ARM: shmobile: kzm9g dts: Move Ethernet node to BSC
ARM: shmobile: sh73a0 dtsi: Add Bus State Controller node
ARM: shmobile: kzm9g: Build DTS for Multiplatform
ARM: shmobile: kzm9g dts: Sync with kzm9g-reference dts
ARM: shmobile: sh73a0: Add Multiplatform support
ARM: shmobile: sh73a0: Introduce generic setup callback
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The delayed_work field in the snd_soc_dapm_context struct is now unused and
can be removed. Removing it reduces the size of the snd_soc_dapm_context
struct by ~50% from 100 bytes to 48 bytes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only two users of the suspend_bias_level field were two rather old
drivers which weren't exactly doing things by the book. Those drivers have
been updated and field is now unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVHATOAAoJEG4XJFUm622b4EsIAIMGOLb2GuqtxpN/Ei1TmUFV
8B3KTLmeau/glqxquySQ2mIthDqijesbl0jyKWJP/+ZsXhjhpagXAIMw6E5KH3HN
1XKCvyqbkGScTcheaS4HYFmKKoM0OlPnDKhybYtPiScW2kyQf8S9msbeEzLdYYen
qYKMRq/J/QuobWvtapyGOBtyuVtuTrKuP8LzKQX9JAyKtM2si/iOvG7EiFmcAcis
DGJBrwhy/i6oBoi6e6KGgxIpXJE9WHsMs2QBYpFkxV2SbzXTOyq1EMFJvMHCq927
QfEsgOgAyVLfsXqN1uNK49eJtTuWRuJehEV88xjUbMXcYQNiaKdnYY6KvIBQ7XU=
=POsk
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
