No functional change, move bitfield calculations to macro
definitions with added clock rate argument, which are in turn defined
by new common SLCTAC_CLOCKS(c, n, s) macro definition.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The WiiU adapter from Mayflash (see
http://www.mayflash.com/Products/NINTENDOWiiU/W009.html) is not
working correctly.
The "XInput" mode works fine, the controller is recognized as a xbox
controller. But it is only possible to connect one controller with this method.
In "DInput" mode the device is recognized as some kind of mouse input but no
joystick is created. This commit will change this behavior with
HID_QUIRK_MULTI_INPUT to split the device into 4 input devices so that it will
also create joysticks in /dev/input/js*.
Signed-off-by: Oliver Schmitt <voltumna@gmx.net>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Parallel Trace Interface (PTI) unit is a trace output device that sends
data over a PTI port.
The driver provides interfaces to configure bus width, bus clock divider
and mode. Tracing is enabled via output device's "active" attribute.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory Storage Unit (MSU) is a trace output device that collects trace
data to system memory. It consists of 2 independent Memory Storage
Controllers (MSCs).
This driver provides userspace interfaces to configure in-memory tracing
parameters, such as contiguous (high-order allocation) buffer or multiblock
(scatter list) buffer mode, wrapping (data overwrite) and number and sizes
of windows in multiblock mode. Userspace can read the buffers via mmap()ing
or read()ing of the corresponding device node.
Signed-off-by: Laurent Fert <laurent.fert@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software Trace Hub (STH) is a trace source device in the Intel TH
architecture, it generates data that then goes through the switch into
one or several output ports.
STH collects data from software sources using the stm device class
abstraction.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Global Trace Hub (GTH) is the central component of Intel TH architecture;
it carries out switching between the trace sources and trace outputs, can
enable/disable tracing, perform STP encoding, internal buffering, control
backpressure from outputs to sources and so on.
This property is also reflected in the software model; GTH (switch) driver
is required for the other subdevices to probe, because it matches trace
output devices against its output ports and configures them accordingly.
It also implements an interface for output ports to request trace enabling
or disabling and a few other useful things.
For userspace, it provides an attribute group "masters", which allows
configuration of per-master trace output destinations for up to master 255
and "256+" meaning "masters 256 and above". It also provides an attribute
group to discover and configure some of the parameters of its output ports,
called "outputs". Via these the user can set up data retention policy for
an individual output port or check if it is in reset state.
Signed-off-by: Laurent Fert <laurent.fert@intel.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic support for PCI-based Intel TH devices. It requests
2 bars (configuration registers for the subdevices and STH channel MMIO
region) and calls into Intel TH core code to create the bus with subdevices
etc.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel(R) Trace Hub (TH) is a set of hardware blocks (subdevices) that
produce, switch and output trace data from multiple hardware and
software sources over several types of trace output ports encoded
in System Trace Protocol (MIPI STPv2) and is intended to perform
full system debugging.
For these subdevices, we create a bus, where they can be discovered
and configured by userspace software.
This patch creates this bus infrastructure, three types of devices
(source, output, switch), resource allocation, some callback mechanisms
to facilitate communication between the subdevices' drivers and some
common sysfs attributes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a simple stm_source class device driver (kernelspace stm trace
source) that registers a console and sends kernel messages over STM
devices.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a simple module that pretends to be an stm device and discards
all the data that comes in. Useful for testing stm class and its users.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A System Trace Module (STM) is a device exporting data in System Trace
Protocol (STP) format as defined by MIPI STP standards. Examples of such
devices are Intel(R) Trace Hub and Coresight STM.
This abstraction provides a unified interface for software trace sources
to send their data over an STM device to a debug host. In order to do
that, such a trace source needs to be assigned a pair of master/channel
identifiers that all the data from this source will be tagged with. The
STP decoder on the debug host side will use these master/channel tags to
distinguish different trace streams from one another inside one STP
stream.
This abstraction provides a configfs-based policy management mechanism
for dynamic allocation of these master/channel pairs based on trace
source-supplied string identifier. It has the flexibility of being
defined at runtime and at the same time (provided that the policy
definition is aligned with the decoding end) consistency.
For userspace trace sources, this abstraction provides write()-based and
mmap()-based (if the underlying stm device allows this) output mechanism.
For kernel-side trace sources, we provide "stm_source" device class that
can be connected to an stm device at run time.
Cc: linux-api@vger.kernel.org
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a patch to make speakup-r work again.
It broke in 3.6 due to commit 4369c64c79
"Input: Send events one packet at a time)
The problem was that the fakekey.c routine to fake a down arrow no
longer functioned properly and putting the input_sync fixed it.
Fixes: 4369c64c79
Cc: stable <stable@vger.kernel.org>
Acked-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: John Covici <covici@ccs.covici.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current VME bus error handler adds errors to the bridge error list.
vme_master_{read,write} then traverses that list to look for relevant
errors.
Such scheme didn't work well for accesses going through vme_master_mmap
because they would also allocate a vme_bus_error, but have no way to do
vme_clear_errors call to free that memory.
This changes the error handling process to be other way around: now
vme_master_{read,write} defines a window in VME address space that will
catch possible errors. VME bus error interrupt only traverses these
windows and marks those that had errors in them.
Signed-off-by: Dmitry Kalinkin <dmitry.kalinkin@gmail.com>
Cc: Igor Alekseev <igor.alekseev@itep.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also changes vme_bus_error_handler to take generic address modifier code
instead of raw contents of a device-specific attribute register.
Signed-off-by: Dmitry Kalinkin <dmitry.kalinkin@gmail.com>
Cc: Igor Alekseev <igor.alekseev@itep.ru>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error handling code found in tsi148 is not device specific. In fact it
already relies on shared vme_bus_error struct and vme_bridge.vme_errors
field. The other bridge driver could reuse this code if it is shared.
This introduces a slight behavior change: vme error message won't be
triggered in a rare case when err_chk=1 and kmalloc fails.
Signed-off-by: Dmitry Kalinkin <dmitry.kalinkin@gmail.com>
Cc: Igor Alekseev <igor.alekseev@itep.ru>
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Universe II allows PCI address grannularity of 4K or 64K depending on
the window id. tsi148 only supports 64K. Existing driver implementations
are validating window size against this grannularity and then use that
very size as alignment parameter to pci_bus_alloc_resource. This
constraint is excessive, alignment by granularity should be enough.
This changes alignment constraint from size to a fixed constraint of
64K.
Signed-off-by: Dmitry Kalinkin <dmitry.kalinkin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a platform driver doesn't provide a .remove callback the function
platform_drv_remove isn't called and so the call to dev_pm_domain_attach
called at probe time isn't paired by dev_pm_domain_detach at remove
time.
To fix this (and similar issues if different callbacks are missing) hook
up the driver callbacks unconditionally and make them aware that the
platform callbacks might be missing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify ida index allocation and removal by
using the ida_simple_* helper functions
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is mostly a hardening fix, given that write-only access to other
users' ttys is usually only given through setgid tty executables.
Signed-off-by: Jann Horn <jann@thejh.net>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds an entry to the uart_config table for PORT_RT2880
enabling rx/tx FIFOs. The UART is actually a Palmchip BK-3103
which is found in several devices from Alchemy/RMI, Ralink, and
Sigma Designs.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART controller is capable to perform transfers up to 4 Mbps.
Remove artificial 115.2 Kbps limitation.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add receive DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add transmit DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make function naming consistent across this driver.
Also rename msm_irq to msm_uart_irq. No functional changes.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit masks for RFR_LEVEL1 and STALE_TIMEOUT_MSB values in MR1 and
IPR registers respectively are different for UART and UART_DM hardware
cores. We have been using UART core mask values for these. Add the same
for UART_DM core.
There is no bit setting as UART_IPR_RXSTALE_LAST for UART_DM core so do
it only for UART core.
Signed-off-by: Pramod Gurav <gpramod@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a wrong compatible flag in specified, the of_match_device
returning null.
Implemented check and if NULL then returning -ENODEV.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They're used by only if CONFIG_PM is enabled, so enclose them
with proper ifdefs. Removes these warnings:
drivers/tty/serial/omap-serial.c:202:12: warning: 'serial_omap_get_context_loss_count' defined but not used [-Wunused-function]
drivers/tty/serial/omap-serial.c:213:13: warning: 'serial_omap_enable_wakeup' defined but not used [-Wunused-function]
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX buffer is allocated from DMA coherent memory. Thus there is no need to call
DMA sync API for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move h/w reinit of serial console restore-from-suspend into
standalone helper function.
No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART clock is set slightly under 1.8432MHz, the 8250 driver
core doesn't permit the 115200 baud rate since it calculates the maximum
frequency to pass to uart_get_baud_rate by simply dividing the uart
clock by 16 which yields a value slightly under 115200, even though the
frequency is close enough for the UART to operate reliably.
Therefore add some tolerance in the calculation of the maximum baud
rate. 1% tolerance allows for marginally slower uart clk than nominal
without introducing transmission errors.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[pjh: Forward-port & refactor original patch; change tolerance to 1%]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three natural ways in which devices may be wired to the system:
little endian (device receives correctly ordered bits of a word written
by little-endian CPU to its register, but big-endian CPU needs to swap
bytes of a word before writing it), big endian (same, but with big-endian
CPU in more favourable position) and native endian (CPU of either
endianness may do word-sized I/O without need for byteswapping).
Adding an option for native endianness allows using single kernel command
line for boards with native-endian serial ports on bi-endian
architectures. This goes in parallel with 'native-endian' DTS attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drivers doesn't claim the serial device to be wakeup source. Even
if it is, it needs to use enable_irq_wake or other related PM wakeup
APIs to enable it.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Cc: linux-serial@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the FD interrupt handler can discern spurious IRQs and it is
shared with timer interrupt, use IRQF_COND_SUSPEND instead of
IRQF_NO_SUSPEND.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function can return negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs, including Ralink/Mediatek and Alchemy Au1xxx, have a
16550-like UART with a non-standard register layout. These are
supported by a simple mapping table in 8250_port.c Rather than
list every SoC type using this access mode in the ifdefs there,
allow selecting the SERIAL_8250_RT288X Kconfig option with any
system and default it to y for the known cases needing it. The
help text is reworded accordingly.
This change simplifies adding support for other SoCs also using
the same UART.
The name of the option is a little misleading, but not knowing
the true origin of this UART, it is as good a choice as any.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Race on buffer data happens when newly committed data is
picked up by an old flush work in the following scenario:
__tty_buffer_request_room does a plain write of tail->commit,
no barriers were executed before that.
At this point flush_to_ldisc reads this new value of commit,
and reads buffer data, no barriers in between.
The committed buffer data is not necessary visible to flush_to_ldisc.
Similar bug happens when tty_schedule_flip commits data.
Update commit with smp_store_release and read commit with
smp_load_acquire, as it is commit that signals data readiness.
This is orthogonal to the existing synchronization on tty_buffer.next,
which is required to not dismiss a buffer with unconsumed data.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_buffer_flush frees not acquired buffers.
As the result, for example, read of b->size in tty_buffer_free
can return garbage value which will lead to a huge buffer
hanging in the freelist. This is just the benignest
manifestation of freeing of a not acquired object.
If the object is passed to kfree, heap can be corrupted.
Acquire visibility over the buffer before freeing it.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_to_ldisc reads port->itty and checks that it is not NULL,
concurrently release_tty sets port->itty to NULL. It is possible
that flush_to_ldisc loads port->itty once, ensures that it is
not NULL, but then reloads it again and uses. The second load
can already return NULL, which will cause a crash.
Use READ_ONCE to read port->itty.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My colleague ran into a program stall on a x86_64 server, where
n_tty_read() was waiting for data even if there was data in the buffer
in the pty. kernel stack for the stuck process looks like below.
#0 [ffff88303d107b58] __schedule at ffffffff815c4b20
#1 [ffff88303d107bd0] schedule at ffffffff815c513e
#2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818
#3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2
#4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23
#5 [ffff88303d107dd0] tty_read at ffffffff81368013
#6 [ffff88303d107e20] __vfs_read at ffffffff811a3704
#7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57
#8 [ffff88303d107f00] sys_read at ffffffff811a4306
#9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7
There seems to be two problems causing this issue.
First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active(). However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
add_wait_queue(&tty->read_wait, &wait);
...
if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
ldata->read_head);
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
spin_lock_irqsave(&q->lock, flags);
/* from add_wait_queue() */
...
if (!input_available_p(tty, 0)) {
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
ldata->read_head);
if (waitqueue_active(&tty->read_wait))
__add_wait_queue(q, wait);
spin_unlock_irqrestore(&q->lock,flags);
/* from add_wait_queue() */
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.
This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation). Moreover, the resulting code is much simpler.
Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If atmel_init_gpios fails the port has already been marked as busy (in
line 2629), so this must be undone in the error path.
This bug was introduced because I created the patch that finally
became 722ccf416a ("serial: atmel: fix error handling when
mctrl_gpio_init fails") on top of 3.19 which didn't have commit
6fbb9bdf0f ("tty/serial: at91: fix error handling in
atmel_serial_probe()") yet.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 722ccf416a ("serial: atmel: fix error handling when mctrl_gpio_init fails")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a3a10ce342 ("Avoid usb reset crashes by making tty_io cdevs truly
dynamic") which mixes using cdev_alloc() and cdev_init() is problematic.
Subsequent call to cdev_init() after cdev_alloc() sets kobj release method
from cdev_dynamic_release() to cdev_default_release() and thus makes it
impossible to free allocated cdev.
This patch also consolidates error path of cdev_add() as cdev can also leak
here if things went wrong.
Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Fixes: a3a10ce342 ("Avoid usb reset crashes by making tty_io cdevs truly dynamic")
Acked-by: Richard Watts <rrw@kynesim.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 9e7b399d65.
Commit ("9e7b399d65") causes the following warning and sometimes
also hangs the system:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:868 mutex_trylock+0x20c/0x22c()
DEBUG_LOCKS_WARN_ON(in_interrupt())
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc7-next-20150818-00001-g14418a6 #4
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
[<80012f08>] (dump_backtrace) from [<800130a4>] (show_stack+0x18/0x1c)
r6:00000364 r5:00000000 r4:00000000 r3:00000000
[<8001308c>] (show_stack) from [<807902b8>] (dump_stack+0x88/0xa4)
[<80790230>] (dump_stack) from [<8002a604>] (warn_slowpath_common+0x80/0xbc)
r5:807945c4 r4:80ab3b50
[<8002a584>] (warn_slowpath_common) from [<8002a6e4>] (warn_slowpath_fmt+0x38/0x40)
r8:00000000 r7:8131100c r6:8054c3cc r5:8131300c r4:80b0a570
[<8002a6b0>] (warn_slowpath_fmt) from [<807945c4>] (mutex_trylock+0x20c/0x22c)
r3:8095d0d8 r2:8095ab28
[<807943b8>] (mutex_trylock) from [<8054c3cc>] (clk_prepare_lock+0x14/0xf4)
r7:8131100c r6:be3f0c80 r5:00000037 r4:be3f0c80
[<8054c3b8>] (clk_prepare_lock) from [<8054dbfc>] (clk_prepare+0x18/0x30)
r5:00000037 r4:be3f0c80
[<8054dbe4>] (clk_prepare) from [<8036a600>] (imx_console_write+0x30/0x244)
r4:812d0bc8 r3:8132b9a4
To reproduce the problem we only need to let the board idle for something
like 30 seconds.
Tested on a imx6q-sabresd.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
