This patch skips the PCI transactions pending check in
ixgbe_disable_pcie_master. This is done to addresses a known HW
issue where the PCI transactions pending bit sticks high when there
are pending transactions. HW engineering instructed to workaround
this issue by wait and then continue with our reset flow.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets RDRXCTL.PSP when the driver is in SRIOV mode which
enables padding of small packets.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting the X550* RDRXCTL register should fall through into X540
and 82599, not 82598.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timeout path is supposed to release the semaphore, so do that.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take control of an I2C mux that selects which SFP is attached to
the I2C bus. The control of the mux is captured in the taking and
releasing of the related semaphore. Because only port 1 can control
the mux, port 1 always leaves the mux set to select port 0.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the frequency of polling for SFP modules. Because the
service task sometimes runs at high rates, we can poll for
SFPs too often. When an SFP is not present, the I2C timeouts
that result are very costly. So, prevent SFP polling from
being done more than once every two seconds. To reduce latency,
the poll time is cleared in a couple of cases to permit the
next service task execution to poll the SFP module.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since SFP+ can be used with some X550 devices, permit them to be
detected.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some hardware platforms, the CS4227 does not initialize properly.
Detect those cases and reset it appropriately.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configures the CS4227 correctly for both 1G and 10G operation,
by moving the code to ixgbe_setup_mac_link_sfp_x550em(). It
needs to be in this function because we need both the module
type and the speed, and this is the only function in the init
flow that knows the speed. In contrast,
ixgbe_setup_sfp_modules_X550em() does not know the speed, so we
can't do anything useful here. This is a fundamental difference
from the previous flow, and is due to the way the CS4227 is
implemented.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds X550EM_x SFP+ dual-speed support. 82599 fiber link
code was moved from ixgbe_82599.c to ixgbe_common.c for use by
X550EM. SFP MAC link code is added to x550EM.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce the number of retries during PHY detection. This reduces
pauses when no SFP is present. Once an SFP is detected, the normal
retry count will be used.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the destination location for I2C data initially so that
the received data will not be affected by previous attempts.
This could have returned wrong data in certain retry sequences.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is primarily for consistancy with vxlan and other tunnels which
use network byte order for similar parameters.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
radeon and amdgpu fixes for 4.3. It's a bit bigger than usual since
it's 3 weeks worth of fixes since I was on vacation, then at XDC.
- lots of stability fixes
- suspend and resume fixes
- GPU scheduler fixes
- Misc other fixes
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux: (31 commits)
drm/radeon: add quirk for MSI R7 370
drm/amdgpu: Sprinkle drm_modeset_lock_all to appease locking checks
drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks
drm/amdgpu: sync ce and me with SWITCH_BUFFER(2)
drm/amdgpu: integer overflow in amdgpu_mode_dumb_create()
drm/amdgpu: info leak in amdgpu_gem_metadata_ioctl()
drm/amdgpu: integer overflow in amdgpu_info_ioctl()
drm/amdgpu: unwind properly in amdgpu_cs_parser_init()
drm/amdgpu: Fix max_vblank_count value for current display engines
drm/amdgpu: use kmemdup rather than duplicating its implementation
drm/amdgpu: fix UVD suspend and resume for VI APU
drm/amdgpu: fix the UVD suspend sequence order
drm/amdgpu: make UVD handle checking more strict
drm/amdgpu: Disable UVD PG
drm/amdgpu: more scheduler cleanups v2
drm/amdgpu: cleanup fence queue init v2
drm/amdgpu: rename fence->scheduler to sched v2
drm/amdgpu: cleanup entity init
drm/amdgpu: refine the scheduler job type conversion
drm/amdgpu: refine the job naming for amdgpu_job and amdgpu_sched_job
...
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mgag200_driver_load's error path just calls the drm driver's
driver_unload op. It isn't safe to call this because it doesn't handle
things well if driver_load fails somewhere mid way.
Replace the call to mgag200_driver_unload with a more finegrained
error handling path.
Link: http://lkml.kernel.org/r/55F6E68D.8070800@codeaurora.org
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Set up error handling in mgag200_fbdev_init and mgag200fb_create such that
they release the things they allocate, rather than relying on someone
calling mga_fbdev_destroy.
Based on a patch by Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: http://lkml.kernel.org/r/55F6E68D.8070800@codeaurora.org
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dri-devel <dri-devel@lists.freedesktop.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the server isn't new enough to give us state, report the first
monitor as always connected, otherwise believe the server side.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case the DaVinci Emac is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-09-22
This series contains updates to e1000, e1000e, igbvf, ixgbe, ixgbevf and
fm10k.
Jacob provides several updates for fm10k, which cleans up comments and
most notably a fix for a corner case issue with the PF/VF mailbox code.
The issue being fm10k_mbx_reset_work clears various states about the
mailbox, but does not clear the Tx FIFO head/tail pointers. We also
are not able to simply clear these pointers, as we would drop
untransmitted messages without error. Also adds support for extra debug
statistics, which provides the ability to see what the PF thinks the
VF mailboxes look like.
Don adds support for SFP+ in X550 and support for SCTP flow director
filters SCTP mask.
Francois Romieu dusts off the e1000 driver and removes some dead calls
to e1000_init_eeprom_params().
Toshiaki Makita provides three patches to enable TSO for stacked VLAN's
on e1000e, igbvf and ixgbevf.
Mark provides the first of several ixgbe updates. First updates the
driver to accept SFP not present error for all devices, since an SFP
can still be inserted. Adds support for SFP insertion interrupt on
X550EM devices with SPFs. Adds I2C combined operations on X550EM
(not X550) devices. Moved the setting of lan_id to before any I2C
eeprom access. Lastly, set the bit bang mode in the hardware when
performing bit banding I2C operations on X550.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We are seeing unexplained TX timeouts under heavy load. Let's try to get
a better idea of what's going on.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low 16 bits of the 'opts1' field in the TX descriptor are supposed
to still contain the buffer length when the descriptor is handed back to
us. In practice, at least on my hardware, they don't. So stash the
original value of the opts1 field and get the length to unmap from
there.
There are other ways we could have worked out the length, but I actually
want a stash of the opts1 field anyway so that I can dump it alongside
the contents of the descriptor ring when we suffer a TX timeout.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We calculate the value of the opts1 descriptor field in three different
places. With two different behaviours when given an invalid packet to
be checksummed — none of them correct. Sort that out.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a TSO frame in multiple buffers, we were neglecting to set
the first descriptor up in TSO mode.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a certain amount of staring at the debug output of this driver, I
realised it was lying to me.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an RX interrupt was already received but NAPI has not yet run when
the RX timeout happens, we end up in cp_tx_timeout() with RX interrupts
already disabled. Blindly re-enabling them will cause an IRQ storm.
(This is made particularly horrid by the fact that cp_interrupt() always
returns that it's handled the interrupt, even when it hasn't actually
done anything. If it didn't do that, the core IRQ code would have
detected the storm and handled it, I'd have had a clear smoking gun
backtrace instead of just a spontaneously resetting router, and I'd have
at *least* two days of my life back. Changing the return value of
cp_interrupt() will be argued about under separate cover.)
Unconditionally leave RX interrupts disabled after the reset, and
schedule NAPI to check the receive ring and re-enable them.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock trace is seen in netcp driver with lockup detector enabled.
The trace log is provided below for reference. This patch fixes the
bug by removing the usage of netcp_modules_lock within ndo_ops functions.
ndo_{open/close/ioctl)() is already called with rtnl_lock held. So there
is no need to hold another mutex for serialization across processes on
multiple cores. So remove use of netcp_modules_lock mutex from these
ndo ops functions.
ndo_set_rx_mode() shouldn't be using a mutex as it is called from atomic
context. In the case of ndo_set_rx_mode(), there can be call to this API
without rtnl_lock held from an atomic context. As the underlying modules
are expected to add address to a hardware table, it is to be protected
across concurrent updates and hence a spin lock is used to synchronize
the access. Same with ndo_vlan_rx_add_vid() & ndo_vlan_rx_kill_vid().
Probably the netcp_modules_lock is used to protect the module not being
removed as part of rmmod. Currently this is not fully implemented and
assumes the interface is brought down before doing rmmod of modules.
The support for rmmmod while interface is up is expected in a future
patch set when additional modules such as pa, qos are added. For now
all of the tests such as if up/down, reboot, iperf works fine with this
patch applied.
Deadlock trace seen with lockup detector enabled is shown below for
reference.
[ 16.863014] ======================================================
[ 16.869183] [ INFO: possible circular locking dependency detected ]
[ 16.875441] 4.1.6-01265-gfb1e101 #1 Tainted: G W
[ 16.881176] -------------------------------------------------------
[ 16.887432] ifconfig/1662 is trying to acquire lock:
[ 16.892386] (netcp_modules_lock){+.+.+.}, at: [<c03e8110>]
netcp_ndo_open+0x168/0x518
[ 16.900321]
[ 16.900321] but task is already holding lock:
[ 16.906144] (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4
[ 16.913206]
[ 16.913206] which lock already depends on the new lock.
[ 16.913206]
[ 16.921372]
[ 16.921372] the existing dependency chain (in reverse order) is:
[ 16.928844]
-> #1 (rtnl_mutex){+.+.+.}:
[ 16.932865] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.938521] [<c04c5758>] register_netdev+0xc/0x24
[ 16.943831] [<c03e65c0>] netcp_module_probe+0x214/0x2ec
[ 16.949660] [<c03e8a54>] netcp_register_module+0xd4/0x140
[ 16.955663] [<c089654c>] keystone_gbe_init+0x10/0x28
[ 16.961233] [<c000977c>] do_one_initcall+0xb8/0x1f8
[ 16.966714] [<c0867e04>] kernel_init_freeable+0x148/0x1e8
[ 16.972720] [<c05f9994>] kernel_init+0xc/0xe8
[ 16.977682] [<c0010038>] ret_from_fork+0x14/0x3c
[ 16.982905]
-> #0 (netcp_modules_lock){+.+.+.}:
[ 16.987619] [<c006eab0>] lock_acquire+0x118/0x320
[ 16.992928] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.998582] [<c03e8110>] netcp_ndo_open+0x168/0x518
[ 17.004064] [<c04c48f0>] __dev_open+0xa8/0x10c
[ 17.009112] [<c04c4b74>] __dev_change_flags+0x94/0x144
[ 17.014853] [<c04c4c3c>] dev_change_flags+0x18/0x48
[ 17.020334] [<c053a9fc>] devinet_ioctl+0x6dc/0x7e4
[ 17.025729] [<c04a59ec>] sock_ioctl+0x1d0/0x2a8
[ 17.030865] [<c0142844>] do_vfs_ioctl+0x41c/0x688
[ 17.036173] [<c0142ae4>] SyS_ioctl+0x34/0x5c
[ 17.041046] [<c000ff60>] ret_fast_syscall+0x0/0x54
[ 17.046441]
[ 17.046441] other info that might help us debug this:
[ 17.046441]
[ 17.054434] Possible unsafe locking scenario:
[ 17.054434]
[ 17.060343] CPU0 CPU1
[ 17.064862] ---- ----
[ 17.069381] lock(rtnl_mutex);
[ 17.072522] lock(netcp_modules_lock);
[ 17.078875] lock(rtnl_mutex);
[ 17.084532] lock(netcp_modules_lock);
[ 17.088366]
[ 17.088366] *** DEADLOCK ***
[ 17.088366]
[ 17.094279] 1 lock held by ifconfig/1662:
[ 17.098278] #0: (rtnl_mutex){+.+.+.}, at: [<c053a418>]
devinet_ioctl+0xf8/0x7e4
[ 17.105774]
[ 17.105774] stack backtrace:
[ 17.110124] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.118637] Hardware name: Keystone
[ 17.122123] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.129862] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.137079] [<c05ff450>] (dump_stack) from [<c0068e34>]
(print_circular_bug+0x210/0x330)
[ 17.145161] [<c0068e34>] (print_circular_bug) from [<c006ab7c>]
(validate_chain.isra.35+0xf98/0x13ac)
[ 17.154372] [<c006ab7c>] (validate_chain.isra.35) from [<c006da60>]
(__lock_acquire+0x52c/0xcc0)
[ 17.163149] [<c006da60>] (__lock_acquire) from [<c006eab0>]
(lock_acquire+0x118/0x320)
[ 17.171058] [<c006eab0>] (lock_acquire) from [<c06023f0>]
(mutex_lock_nested+0x68/0x4a8)
[ 17.179140] [<c06023f0>] (mutex_lock_nested) from [<c03e8110>]
(netcp_ndo_open+0x168/0x518)
[ 17.187484] [<c03e8110>] (netcp_ndo_open) from [<c04c48f0>]
(__dev_open+0xa8/0x10c)
[ 17.195133] [<c04c48f0>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.203129] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.211560] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.219729] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.227378] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.234939] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.242242] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.258855] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 17.271282] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 17.279712] in_atomic(): 1, irqs_disabled(): 0, pid: 1662, name: ifconfig
[ 17.286500] INFO: lockdep is turned off.
[ 17.290413] Preemption disabled at:[< (null)>] (null)
[ 17.295728]
[ 17.297214] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.305735] Hardware name: Keystone
[ 17.309223] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.316970] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.324194] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 17.332112] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 17.340724] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 17.348982] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 17.356724] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.364729] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.373166] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.381344] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.388994] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.396563] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.403873] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.413772] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
[ 18.690666] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
Sending discover...
[ 22.250972] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 22.258721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.265458] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 22.273896] in_atomic(): 1, irqs_disabled(): 0, pid: 342, name: kworker/1:1
[ 22.280854] INFO: lockdep is turned off.
[ 22.284767] Preemption disabled at:[< (null)>] (null)
[ 22.290074]
[ 22.291568] CPU: 1 PID: 342 Comm: kworker/1:1 Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 22.300255] Hardware name: Keystone
[ 22.303750] Workqueue: ipv6_addrconf addrconf_dad_work
[ 22.308895] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 22.316643] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 22.323867] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 22.331786] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 22.340394] [<c03e9840>] (netcp_set_rx_mode) from [<c04c9d18>]
(__dev_mc_add+0x54/0x68)
[ 22.348401] [<c04c9d18>] (__dev_mc_add) from [<c05ab358>]
(igmp6_group_added+0x168/0x1b4)
[ 22.356580] [<c05ab358>] (igmp6_group_added) from [<c05ad2cc>]
(ipv6_dev_mc_inc+0x4f0/0x5a8)
[ 22.365019] [<c05ad2cc>] (ipv6_dev_mc_inc) from [<c058f0d0>]
(addrconf_dad_work+0x21c/0x33c)
[ 22.373460] [<c058f0d0>] (addrconf_dad_work) from [<c0042850>]
(process_one_work+0x214/0x8d0)
[ 22.381986] [<c0042850>] (process_one_work) from [<c0042f54>]
(worker_thread+0x48/0x4bc)
[ 22.390071] [<c0042f54>] (worker_thread) from [<c004868c>]
(kthread+0xf0/0x108)
[ 22.397381] [<c004868c>] (kthread) from [<c0010038>]
Trace related to incorrect usage of mutex inside ndo_set_rx_mode
[ 24.086066] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 24.094506] in_atomic(): 1, irqs_disabled(): 0, pid: 1682, name: ifconfig
[ 24.101291] INFO: lockdep is turned off.
[ 24.105203] Preemption disabled at:[< (null)>] (null)
[ 24.110511]
[ 24.112005] CPU: 2 PID: 1682 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 24.120518] Hardware name: Keystone
[ 24.124018] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 24.131772] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 24.138989] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 24.146908] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 24.155523] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 24.163787] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 24.171531] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 24.179528] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 24.187966] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 24.196145] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 24.203803] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 24.211373] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 24.218676] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 24.227156] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_rxpool_refill() that refill descriptors and attached
buffers to fdq while interrupt is enabled as part of NAPI poll. Doing
it while interrupt is disabled could be beneficial as hardware will
not be starved when CPU is busy with processing interrupt.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_module_probe() doesn't check the return value of
of_parse_phandle() that points to the interface data for the
module and then pass the node ptr to the module which is incorrect.
Check for return value and free the intf_modpriv if there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if netcp_allocate_rx_buf() fails due no descriptors
in the rx free descriptor queue, inside the netcp_rxpool_refill() function
the iterative loop to fill buffers doesn't terminate right away. So modify
the netcp_allocate_rx_buf() to return an error code and use it break the
loop when there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp interface is not fully initialized before attach the module
to the interface. For example, the tx pipe/rx pipe is initialized
in ethss module as part of attach(). So until this is complete, the
interface can't be registered. So move registration of interface to
net device outside the current loop that attaches the modules to the
interface.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netcp_core is the first driver that will get initialized and the modules
(ethss, pa etc) will then get initialized. So the code at the end of
netcp_probe() that iterate over the modules is a dead code as the module
list will be always be empty. So remove this code.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On K2HK, sgmii module registers of slave 0 and 1 are mem
mapped to one contiguous block, while those of slave 2
and 3 are mapped to another contiguous block. However,
on K2E and K2L, sgmii module registers of all slaves are
mem mapped to one contiguous block. SGMII APIs expect
slave 0 sgmii base when API is invoked for slave 0 and 1,
and slave 2 sgmii base when invoked for other slaves.
Before this patch, slave 0 sgmii base is always passed to
sgmii API for K2E regardless which slave is the API invoked
for. This patch fixes the problem.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timer to each rocker switch to do FDB entry cleanup by ageing out
expired entries. The timer scheduling algo is copied from the bridge
driver, for the most part, to keep the firing of the timer to a minimum.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patcheset will allow user to change ageing_time, but for now
just hard-code it to a fixed value (the same value used as the default
for the bridge driver).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need more info from rocker_port than just pport when we age out fdb
entries, so store rocker_port rather than pport in each fdb entry.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry is touched once when created, and touched again for each update.
The touched time is used to calculate FDB entry age.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just adds the quirk for MSI R7 370 Armor 2X
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91294
Signed-off-by: Maxim Sheviakov <mrader3940@yandex.ru>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In
commit 7a3f3d6667
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:44:28 2015 +0200
drm: Check locking in drm_for_each_connector
I added locking checks to drm_for_each_connector but failed that
through drm_helper_connector_dpms -> drm_helper_choose_encoder_dpms
it's used in a few more places in the amdgpu resume/suspend code.
Fix them up.
Note that we could use the connector iterator macros in there too, but
that's for the future.
Port of radeon commit:
drm/radeon: Sprinkle drm_modeset_lock_all to appease locking checks
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In
commit 7a3f3d6667
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:44:28 2015 +0200
drm: Check locking in drm_for_each_connector
I added locking checks to drm_for_each_connector but failed that
through drm_helper_connector_dpms -> drm_helper_choose_encoder_dpms
it's used in a few more places in the radeon resume/suspend code.
Fix them up.
Note that we could use the connector iterator macros in there too, but
that's for the future.
Reported-and-tested-by: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we used to adopt wait_reg_mem to let CE wait before DE finish page
updating, but from Tonga+, CE doesn't support wait_reg_mem package so
this logic no longer works.
so here is another approach to do same thing:
Insert two of SWITCH_BUFFER at both front and end of vm_flush can
guarantee that CE not go further to process IB_const before vm_flush
done.
Insert two of SWITCH_BUFFER also works on CI, so remove legency method
to sync CE and ME
v2:
Insert double SWITCH_BUFFER at front of vm flush as well.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
args->size is a u64. arg->pitch and args->height are u32. The
multiplication will overflow instead of using the high 32 bits as
intended.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no limit on args->data.data_size_bytes so we could read beyond
the end of the args->data.data[] array.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "alloc_size" calculation can overflow leading to memory corruption.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The amdgpu_cs_parser_init() function doesn't clean up after itself but
instead the caller uses a free everything function amdgpu_cs_parser_fini()
on failure. This style of error handling is often buggy. In this
example, we call "drm_free_large(parser->chunks[i].kdata);" when it is
an unintialized pointer or when "parser->chunks" is NULL.
I fixed this bug by adding unwind code so that it frees everything that
it allocates.
I also mode some other very minor changes:
1) Renamed "r" to "ret".
2) Moved the chunk_array allocation to the start of the function.
3) Removed some initializers which are no longer needed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value was much too low, which could cause the userspace visible
vblank counter to move backwards when the hardware counter wrapped
around.
Ported from radeon commit:
b0b9bb4dd5
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
User space passed the same handle before suspend and after resume,
so we have remove the session and handle destroy, and keep the
firmware untouched.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
