Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Add the pinctrl driver for the Qualcomm Technologies QDF2xxx ARM64 SoCs,
which uses the Qualcomm Technologies TLMM pinctrl/gpio device. This
driver is probed via ACPI and uses the pinctrl-msm.c backend driver.
This driver is intended to be used only an ACPI-enabled system. As such,
UEFI will handle all pin control configuration, so this driver does not
provide pin control functions. It is effectively a GPIO-only driver.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This introduces pinctrl drivers for gpio and mpp blocks found in family A
PMICs.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here's some staging and IIO driver fixes for 4.2-rc3.
Nothing major, the majority are IIO issues that were reported, with a
few other minor staging driver fixes. All have been in linux-next for a
while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWpRFUACgkQMUfUDdst+yke/wCeJPDuYuOp/SFhyviMx9ojKIGF
kVIAoI1xDY4SwVExztXcqyKo6m0H2yZ4
=pxAa
-----END PGP SIGNATURE-----
Merge tag 'staging-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here's some staging and IIO driver fixes for 4.2-rc3.
Nothing major, the majority are IIO issues that were reported, with a
few other minor staging driver fixes. All have been in linux-next for
a while with no reported issues"
* tag 'staging-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (25 commits)
staging: vt6656: check ieee80211_bss_conf bssid not NULL
staging: vt6655: check ieee80211_bss_conf bssid not NULL
staging:lustre: remove irq.h from socklnd.h
staging: make board support depend on OF_IRQ and CLKDEV_LOOKUP
iio: tmp006: Check channel info on write
iio: sx9500: Add missing init in sx9500_buffer_pre{en,dis}able()
iio:light:ltr501: fix regmap dependency
iio:light:ltr501: fix variable in ltr501_init
iio: sx9500: fix bug in compensation code
iio: sx9500: rework error handling of raw readings
iio: magnetometer: mmc35240: fix available sampling frequencies
iio:light:stk3310: Fix REGMAP_I2C dependency
iio: light: STK3310: un-invert proximity values
iio:adc:cc10001_adc: fix Kconfig dependency
iio: light: tcs3414: Fix bug preventing to set integration time
iio:accel:bmc150-accel: fix counting direction
iio:light:cm3323: clear bitmask before set
iio: adc: at91_adc: allow to use full range of startup time
iio: DAC: ad5624r_spi: fix bit shift of output data value
iio: proximity: sx9500: Fix proximity value
...
The register layout of the PSC devices differ between MPC5121 and
MPC5125, but the registers are named nearly identical and their purpose
is similar enough ("freescale identical") such that substituting
mpc52xx_psc by mpc5125_psc is nearly enough to make the driver work on
MPC5125. To keep supporting MPC5121 this patch introduces a cpp
macro to select the right struct that defines the register layout.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's some USB driver fixes for 4.2-rc3.
The ususal number of gadget driver fixes are in here, along with some
new device ids and a build fix for the mn10300 arch which required some
symbols to be renamed in the mos7720 driver.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWpRQEACgkQMUfUDdst+ykQTACfbXmLNn/1ycArRysqHGg5llIZ
pdIAn2Yi8TCbXr9HvtugUcxQrDIANNcF
=WUtC
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here's some USB driver fixes for 4.2-rc3.
The ususal number of gadget driver fixes are in here, along with some
new device ids and a build fix for the mn10300 arch which required
some symbols to be renamed in the mos7720 driver.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: Destroy serial_minors IDR on module exit
usb: gadget: f_midi: fix error recovery path
usb: phy: mxs: suspend to RAM causes NULL pointer dereference
usb: gadget: udc: fix free_irq() after request_irq() failed
usb: gadget: composite: Fix NULL pointer dereference
usb: gadget: f_fs: do not set cancel function on synchronous {read,write}
usb: f_mass_storage: limit number of reported LUNs
usb: dwc3: core: avoid NULL pointer dereference
usb: dwc2: embed storage for reg backup in struct dwc2_hsotg
usb: dwc2: host: allocate qtd before atomic enqueue
usb: dwc2: host: allocate qh before atomic enqueue
usb: musb: host: rely on port_mode to call musb_start()
USB: cp210x: add ID for Aruba Networks controllers
USB: mos7720: rename registers
USB: option: add 2020:4000 ID
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJVqUFGAAoJECTWi3JdVIfQ3YUH+LWLxVerlyUj/uug4vhRLlp2
KkKLInX1r9Al8cRWo6ln3kdB8jTmOxFxm1XUkpz+IQLiF0yV5kGtVm7uBup/X4DA
5oi7313rPs4maS/jqwyuOUi8X+ZMkKxp1Pgf4dJAzRJPN5tlks3drYdqY2c7JdT0
q5IqUR1KIsouK1/wCBy17BEe9PLpjV6U/yN2E/b1tsW1utjtAgY5pPjv/MZpPJ8C
NI6WXHjdykIi6Peg1mHqczgGEkyRlKBllZVsOvFhX1yjy0ITvao5/Mpv8NK5BwwU
cOWPVLlXOwa4m+kVXePPgA4GlB2q1Xupw5k6TDPip5aCGUgS+ryKQmOVcNaJnA==
=C5/o
-----END PGP SIGNATURE-----
Merge tag 'regmap-seq-delay-api' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-wm5110
regmap: Create a new struct reg_sequence for register sequences
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
This driver makes it possible to configure the static memory
chip selects on the ARM PL172 MultiPort Memory Controller
from a set of properties in DT. Configuration of dynamic
memory is not supported and is left to the boot loader.
The intended usage is to setup timing and configuration for
static memory devices like NAND and NOR Flash before they
are probed by a driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
hitting individual drivers and nothing else.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mTd/
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"This is a first set of GPIO fixes for the v4.2 series, all hitting
individual drivers and nothing else (except for a documentation
oneliner. I intended to send a request earlier but life intervened)"
* tag 'gpio-v4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: fix nested irqs rescheduling
gpio: omap: prevent module from being unloaded while in use
gpio: max732x: Add missing dev reference to gpiochip
gpio/xilinx: Use correct address when setting initial values.
gpio: zynq: Fix problem with unbalanced pm_runtime_enable
gpio: omap: add missed spin_unlock_irqrestore in omap_gpio_irq_type
gpio: brcmstb: fix null ptr dereference in driver remove
gpio: Remove double "base" in comment
Pull drm fixes from Dave Airlie:
"Fixes all over the place.
The rockchip and imx fixes I missed while on holidays, so I've queued
them now which makes this a bit bigger.
The rest is misc amdgpu, radeon, i915 and armada.
I think the most important thing is the ioctl fix, we dropped the
avoid compat ball, so we get to add a compat wrapper.
There is also an i915 revert to avoid a regression with existing
userspace"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (43 commits)
drm/ttm: improve uncached page deallocation.
drm/ttm: fix uncached page deallocation to properly fill page pool v3.
drm/amdgpu/dce8: Re-set VBLANK interrupt state when enabling a CRTC
drm/radeon/ci: silence a harmless PCC warning
drm/amdgpu/cz: silence some dpm debug output
drm/amdgpu/cz: store the forced dpm level
drm/amdgpu/cz: unforce dpm levels before forcing to low/high
drm/amdgpu: remove bogus check in gfx8 rb setup
drm/amdgpu: set proper index/data pair for smc regs on CZ (v2)
drm/amdgpu: disable the IP module if early_init returns -ENOENT (v2)
drm/amdgpu: stop context leak in the error path
drm/amdgpu: validate the context id in the dependencies
drm/radeon: fix user ptr race condition
drm/radeon: Don't flush the GART TLB if rdev->gart.ptr == NULL
drm/radeon: add a dpm quirk for Sapphire Radeon R9 270X 2GB GDDR5
drm/armada: avoid saving the adjusted mode to crtc->mode
drm/armada: fix overlay when partially off-screen
drm/armada: convert overlay to use drm_plane_helper_check_update()
drm/armada: fix gem object free after failed prime import
drm/armada: fix incorrect overlay plane cleanup
...
Add videobuf2 specific vb2_qbuf and vb2_dqbuf trace events that mirror the
v4l2_qbuf and v4l2_dqbuf trace events, only they include additional
information about queue fill state and are emitted right before the buffer
is enqueued in the driver or userspace is woken up. This allows to make
sense of the timeline of trace events in combination with others that might
be triggered by __enqueue_in_driver.
Also two new trace events vb2_buf_queue and vb2_buf_done are added,
allowing to trace the handover between videobuf2 framework and driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue owner will be used by videobuf2 trace events to determine and
record the device minor number. It is set in v4l2_m2m_reqbufs instead of
v4l2_m2m_ioctl_reqbufs because several drivers implement their own
vidioc_reqbufs handlers that still call v4l2_m2m_reqbufs directly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The chroma interleaved NV12 format has higher memory bandwidth efficiency
because the chroma planes can be read/written with longer burst lengths.
Use NV12 as default format if available and consistently sort it first.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Storing internal frames in macroblock tiled order improves memory
access patterns by allowing increased burst sizes when transferring
the uncompressed macroblocks to or from main memory.
The translation logic only supports a single chroma base address,
so this is only supported for the chroma interleaved NV12 format.
Since the rotator used to copy the decoder output into the v4l2
capture buffers does not seem to support the tiled format correctly,
only enable it in the encoder for now.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The frame cache should be set up correctly to encode NV12 source frames.
This was not done before, so move the cache setup out of start_decoding
into its own function and call it from both start_encoding and
start_decoding.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The encoder needs to know the nominal framerate for the constant bitrate
control mechanism to work. Currently the only way to set the framerate is
by using VIDIOC_S_PARM on the output queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The encoder allows to specify the VBV model reference decoder's initial
delay and buffer size. Export the corresponding V4L2 controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On i.MX6, sometimes after decoding a stream, encoding will produce macroblock
errors caused by missing 8-byte sequences in the output stream. Until the cause
for this is found, reset the hardware after sequence end, which seems to help.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Keep count of number of buffer meta structures in the list and use
a separate spinlock for operations on this counted list instead
of reusing the bitstream mutex in some places and none at all in
others.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_m2m_num_src_bufs_ready() function is called in multiple places
in coda_cob_ready, and there already is a variable src_bufs that is
assigned to its result. Move it to the beginning and use it everywhere.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Trace events with exactly the same parameters and trace output, such as
coda_enc_pic_run and coda_enc_pic_done, are supposed to use the
DECLARE_EVENT_CLASS and DEFINE_EVENT macros instead of duplicated
TRACE_EVENT macro calls.
This patch changes the order of parameters to coda_dec_rot_done and adds
a timestamp so it can share an event class with coda_bit_queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit ba3002045f ("[media] v4l2-ioctl: fill in the description
for VIDIOC_ENUM_FMT"), all pixel formats are assigned their description
in a central place. We can now drop the custom list.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow coda_seq_end_work to be called multiple times, move the setting
of ctx->initialized from coda_start/stop_streaming() into
coda_start_encoding/decoding and coda_seq_end_work, respectively,
and skip the SEQ_END command in coda_seq_end_work if the context is
already deinitialized before.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In stream end mode the hardware will read the bitstream to its end,
overshooting the write pointer. Do not write additional data into
the bitstream in this mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All decoder instances using the BIT processor should preload buffers
into the bitstream ring buffer, including MPEG4 decoding. Fix this
by explicitly stating the above condition instead of listing all
relevant input formats.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mvcol buffer is allocated at the end of the first internal buffer.
This patch fixes an out of bounds array access.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is already done for one side of the comparison with the expectation
that the HW counter rolls over at the 16 bit boundary. This is true when
decoding a h.264 stream, but doesn't hold for at least MJPEG. As we don't
know the exact wrap-around point for this format just clamp the HW counter
to the same 16 bits. This should be enough to detect most of the errors
and saves us from doing different comparisons based on the decoded format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.
While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add RSA support to QAT driver.
Removed unused RNG rings.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Load Modular Math Processor(MMP) firmware into QAT devices to support
public key algorithm acceleration.
Signed-off-by: Pingchao Yang <pingchao.yang@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The vsp1_entity_is_streaming() function is called in atomic context when
queuing buffers, and sleeps due to a mutex. As the mutex just protects
access to one structure field, fix this by replace the mutex with a
spinlock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The checks need to be performed on up to two planes, as the third plane,
if present, must have the same stride and size as the second plane.
The code incorrectly performs the checks on at least two planes instead
of at most two planes, fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should set "ret" on this error path instead of returning success.
Fixes: df3305156f ('[media] v4l: xilinx: Add Xilinx Video IP core')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver is tested on our hardware and all the implemented features
works as expected.
Missing features:
- CEC support
- HDCP repeater support
- IR support
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
[hans.verkuil@cisco.com: updated copyright year to 2015]
[hans.verkuil@cisco.com: update confusing confctl_mutex comment]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
bdisp_dev->dbg.copy_node shall be a copy of (and not point to)
bdisp_ctx->node, since this resource is freed upon driver release.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the composing (at VIDEO_CAPTURE) with the _selection API.
v4l2-compliance successfully run ("test Composing: OK")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit implements frame decimation for stk1160, which allows
to support format changes instead of a static frame size.
The stk1160 supports independent row and column decimation, in two
different modes:
* set a number of rows/columns units to skip for each unit sent.
* set a number of rows/columns units to send for each unit skipped.
This effectively allows to achieve different frame scaling ratios.
The unit number can be set to either two row/columns sent/skipped,
or four row/columns sent/skipped. Since the video format (UYVY)
has 4-bytes, using a unit number of two row/columns results
in frame color 'shifting', so set to four row/columns sent/skipped.
Signed-off-by: Michael Stegemann <michael@stegemann.it>
Signed-off-by: Dale Hamel <dale.hamel@srvthe.net>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These messages are not really informational, and just makes the driver's
output too verbose. This commit changes some messages to a debug level,
removes a really useless "driver loaded" message and finally undefines
the DEBUG macro.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Upon a S_FMT the input/requested frame size and pixel format is
overwritten by the current sub-device settings.
Fix this so application can actually set the frame size and format.
Fixes: 417d2e507e ("[media] media: platform: add VPFE capture driver support for AM437X")
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of VIDEO_ADV7604 and VIDEO_COBALT (the latter
selects the former) on GPIOLIB if COMPILE_TEST is enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the new v4l2_subdev_notify_event() helper function to deliver the
resolution change event to userspace via the v4l2 subdev event queue as
well as to the bridge driver using the callback notify mechanism.
This allows userspace applications to react to changes in resolution. This
is useful and often necessary for video pipelines where there is no direct
1-to-1 relationship between the subdevice converter and the video capture
device and hence it does not make sense to directly forward the event to
the video capture device node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
[hans.verkuil@cisco.com: fix obvious mistake: v4l2_event_subdev_unsubscribe -> v4l2_ctrl_subdev_subscribe_event]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new helper function called v4l2_subdev_notify_event() which will
deliver the specified event to both the v4l2 subdev event queue as well as
to the notify callback. The former is typically used by userspace
applications to listen to notification events while the later is used by
bridge drivers. Combining both into the same function avoids boilerplate
code in subdev drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>