The specification was updated the remove the double word just after
number of configuration groups and capabilities. Update the identify
structure to reflect it.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The ppa format was not copied from the NVMe specific ppa format to the
lightnvm specific ppa format. This led to the ppa format not being
communicated to the layers above.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The linear and device specific address modes can be replaced with a
simple offset and bit length conversion that is generic across all
devices.
This both simplifies the specification and removes the special case for
qemu nvme, that previously relied on the linear address mapping.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both the nvm_register and nvm_init does a kfree(dev) on error. Make sure
to only free it once.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
We register with nvm_devices when there registration can still fail.
Move the final registration at the end of the nvm_register function
to make sure we are fully registered when added to the nvm_devices list.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Only NAND flash with SLC and MLC is supported. Make sure to not try to
initialize TLC memory or other non-volatile memory types.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The mccap field is required for I/O command option support. It defines the
following flash access modes:
* SLC mode
* Erase/Program Suspension
* Scramble On/Off
* Encryption
It is slotted in between mpos and cpar, changing the offset for
cpar as well.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A single 8 bit and 16 bit reserve field were inserted in the
specification to align fields appropriately. Reflect this in the
identify group structure.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The specification was changed to reflect a multi-value bad block table.
Instead of bit-based bad block table, the bad block table now allows
eight bad block categories. Currently four are defined:
* Factory bad blocks
* Grown bad blocks
* Device-side reserved blocks
* Host-side reserved blocks
The factory and grown bad blocks are the regular bad blocks. The
reserved blocks are either for internal use or external use. In
particular, the device-side reserved blocks allows the host to
bootstrap from a limited number of flash blocks. Reducing the flash
blocks to scan upon super block initialization.
Support for both get bad block table and set bad block table is added.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that IP1000A chips are supported by dl2k driver, the buggy ipg
driver can be removed.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that IRQ number passed to dev_pm_set_wake_irq() and
dev_pm_set_dedicated_wake_irq() is valid (not negative) before
accepting it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Otherwise debugging locked up processes isn't possible.
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Dell DW5580 is a 3G modem, this patch adds the device as a
mobile broadband adapter
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "e255787 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
moved send completion polling under HTT Rx (CE 5) service routine. For
QCA6174 based devices copy engine 1 (CE 1) is used for HTT Rx instead
of CE 5. So send completion never be called. This is causing "failed to
transmit packet, dropping: -105" errors. Fix this by processing send
completion from CE 1 service routine instead of CE 5.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Tested-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probe error operation and remove operation are same.
Let's use same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
If multiple NAND chips are registered to the same controller, then when
rebooting the system, the first one will grab the controller lock, while
the second will wait forever for the first one to release it. i.e., a
classic deadlock.
This problem was solved for a similar case (suspend/resume) back in
commit 6b0d9a8412 ("mtd: nand: fix multi-chip suspend problem"), and
the shutdown state really isn't much different for us, so rather than
adding a new special case to nand_get_device(), we can just overload the
FL_PM_SUSPENDED state.
Now, multiple chips can "get" the same controller lock (preventing
further I/O), while we still allow other chips to pass through
nand_shutdown().
Original report:
http://thread.gmane.org/gmane.linux.drivers.mtd/59726http://lists.infradead.org/pipermail/linux-mtd/2015-July/059992.html
Fixes: 72ea403669 ("mtd: nand: added nand_shutdown")
Reported-by: Andrew E. Mileski <andrewm@isoar.ca>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Andrew E. Mileski <andrewm@isoar.ca>
Acked-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some systems register thermal zone by themself and don't need to
have thermal zones node in DT. Therefore reduce the log level from
ERROR to DEBUG when thermal zone node can't be find in
of_thermal_destroy_zones().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fallout from commit 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
We see errors like this:
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_detect_bank':
drivers/mtd/nand/jz4740_nand.c:340:9: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:340:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/jz4740_nand.c:359:2: error: implicit declaration of function 'jz_gpio_set_function' [-Werror=implicit-function-declaration]
drivers/mtd/nand/jz4740_nand.c:359:29: error: 'JZ_GPIO_FUNC_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:399:29: error: 'JZ_GPIO_FUNC_NONE' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_probe':
drivers/mtd/nand/jz4740_nand.c:528:13: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_remove':
drivers/mtd/nand/jz4740_nand.c:555:14: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
Patched similarly to:
https://patchwork.linux-mips.org/patch/11089/
Fixes: 832f5dacfa ("MIPS: Remove all the uses of custom gpio.h")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With a 64-bit resource_size_t, we get a build warning on bcm63xx_spi_probe:
drivers/spi/spi-bcm63xx.c:565:16: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
As we are printing a resource, we can just use the %pr format
specifier that pretty-prints the address and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can now select clocksource drivers like ti-32k and CONFIG_OF
on ancient machines that still use gettimeoffset, and the combination
results in a link error.
arch/arm/kernel/built-in.o: In function `time_init':
(.init.text+0xc28): undefined reference to `clocksource_probe'
The reason for this is that the Makefile is hidden behind
CONFIG_ARCH_USES_GETTIMEOFFSET, but the Kconfig file is not, and
it has shown up just now because the ti-32k driver was added
and can be selected using COMPILE_TEST on all platforms.
This patch hides the Kconfig menu in CONFIG_ARCH_USES_GETTIMEOFFSET
as well.
Fixes: dfedaf105d "clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE"
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/7579471.4N90fYPQOK@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ftm_clockevent_init passes the value of "~0UL" into a function
that takes a 32-bit argument, which drops the upper 32 bits, as
gcc warns about on ARM64:
clocksource/fsl_ftm_timer.c: In function 'ftm_clockevent_init':
clocksource/fsl_ftm_timer.c:206:13: warning: large integer implicitly truncated to unsigned type [-Woverflow]
This was obviously unintended behavior, and is easily avoided by
using '~0u' as the integer literal, because that is 32-bit wide
on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Xiubo Li <Li.Xiubo@freescale.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/3990834.xnjhm37Grs@wuerfel
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Fixes: ea98b29a05 ("hwmon: Support sensors exported via ARM SCP interface")
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68acc77a2d ("hwmon: Support thermal zones registration for SCP temperature sensors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When only one device is present, it is not necessary to specify
cs_gpios, as the CS line can be controlled by the hardware
module.
Without this patch, older device tree bindings used before
37457607 "spi: mediatek: mt8173 spi multiple devices support"
would cause a panic on boot. This fixes the crash, and
re-introduces backward compatibility.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DEVICE_HWI type was added under the faulty assumption that Huawei
devices based on Qualcomm chipsets and firmware use the static USB
interface numbering known from Gobi devices. But this model does
not apply to Huawei devices like the HP branded lt4112 (Huawei me906e).
Huawei firmwares will dynamically assign interface numbers. Functions
are renumbered when the firmware is reconfigured.
Fix by changing the DEVICE_HWI type to use a simplified version
of Huawei's subclass + protocol scheme: Blacklisting known network
interface combinations and assuming the rest are serial.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch>
Tested-by: Martin Hauke <mardnh@gmx.de>
Cc: <stable@vger.kernel.org>
Fixes: e7181d005e ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Shmobile is all multiplatform these days, so get rid of the reference to
CONFIG_ARCH_SHMOBILE_MULTI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds missing AHCI RAID SATA Device IDs for the Intel Sunrise
Point PCH.
Signed-off-by: Nanda Kishore Chinna <nanda_kishore_chinna@dell.com>
Signed-off-by: Charles Rose <charles_rose@dell.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
otg_dev->extcon was referenced before otg_dev was initialized. Fix.
Cc: <stable@vger.kernel.org> # v4.3
Fixes: a2fd242324 ("usb: phy: omap-otg: Replace deprecated API of extcon")
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a bit of a mess in the order of arguments to the ulpi write
callback. There is
int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)
in drivers/usb/common/ulpi.c;
struct usb_phy_io_ops {
...
int (*write)(struct usb_phy *x, u32 val, u32 reg);
}
in include/linux/usb/phy.h.
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e4 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Change-Id: I93a861cd6707f7d91672b9e19757cc50008cd7a2
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
We need to clear parser.ibs and num_ibs before amd_sched_fence_create,
otherwise the IB could be freed twice if fence creates fails.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Before this patch the scheduler fence was created when we push the job
into the queue, so we could only get the fence after pushing it.
The mutex now was necessary to prevent the thread pushing the jobs to
the hardware from running faster than the thread pushing the jobs into
the queue.
Otherwise the thread pushing jobs into the queue would have accessed
possible freed up memory when it tries to get a reference to the fence.
So what you get in the end is thread A:
mutex_lock(&job->lock);
...
Kick of thread B.
...
mutex_unlock(&job->lock);
And thread B:
mutex_lock(&job->lock);
....
mutex_unlock(&job->lock);
kfree(job);
I'm actually not sure if I'm still up to date on this, but this usage
pattern used to be not allowed with mutexes. See here as well
https://lwn.net/Articles/575460/.
v2: remove unrelated changes, fix missing owner
v3: rebased, add more commit message
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The code was correct, but getting two references when the ownership
is linearly moved on is a bit awkward and just overhead.
Signed: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
