Make sure .disconnect() doesn't cleanup the device if
.resume() failed. This may happen when device is removed
during suspend.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Users of older Ralink devices report that received frames
sometimes have zero length. Watch out for that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows e.g. user space to use /sys/class/ieee80211/*/macaddress
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.
Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel is not trying to increase mcbufsz. It suggests you should try
doing so. Also print the calculated required size of mcbufsz.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rework slave configuration part in order to more report wrong errors
about the configuration.
Only maxburst and addr width values are checked when doing the slave
configuration. The validity of the channel configuration is done at
prepare time.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Using _bh variant for spin locks causes this kind of warning:
Starting logging: ------------[ cut here ]------------
WARNING: CPU: 0 PID: 3 at /ssd_drive/linux/kernel/softirq.c:151
__local_bh_enable_ip+0xe8/0xf4()
Modules linked in:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.1.0-rc2+ #94
Hardware name: Atmel SAMA5
[<c0013c04>] (unwind_backtrace) from [<c00118a4>] (show_stack+0x10/0x14)
[<c00118a4>] (show_stack) from [<c001bbcc>]
(warn_slowpath_common+0x80/0xac)
[<c001bbcc>] (warn_slowpath_common) from [<c001bc14>]
(warn_slowpath_null+0x1c/0x24)
[<c001bc14>] (warn_slowpath_null) from [<c001e28c>]
(__local_bh_enable_ip+0xe8/0xf4)
[<c001e28c>] (__local_bh_enable_ip) from [<c01fdbd0>]
(at_xdmac_device_terminate_all+0xf4/0x100)
[<c01fdbd0>] (at_xdmac_device_terminate_all) from [<c02221a4>]
(atmel_complete_tx_dma+0x34/0xf4)
[<c02221a4>] (atmel_complete_tx_dma) from [<c01fe4ac>]
(at_xdmac_tasklet+0x14c/0x1ac)
[<c01fe4ac>] (at_xdmac_tasklet) from [<c001de58>]
(tasklet_action+0x68/0xb4)
[<c001de58>] (tasklet_action) from [<c001dfdc>]
(__do_softirq+0xfc/0x238)
[<c001dfdc>] (__do_softirq) from [<c001e140>] (run_ksoftirqd+0x28/0x34)
[<c001e140>] (run_ksoftirqd) from [<c0033a3c>]
(smpboot_thread_fn+0x138/0x18c)
[<c0033a3c>] (smpboot_thread_fn) from [<c0030e7c>] (kthread+0xdc/0xf0)
[<c0030e7c>] (kthread) from [<c000f480>] (ret_from_fork+0x14/0x34)
---[ end trace b57b14a99c1d8812 ]---
It comes from the fact that devices can called some code from the DMA
controller with irq disabled. _bh variant is not intended to be used in
this case since it can enable irqs. Switch to irqsave/irqrestore variant to
avoid this situation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org # 4.0 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the commit below, I missed the connector allocation in the function
intel_sdvo_analog_init(), leading to those connectors to have a NULL
state pointer.
commit 08d9bc920d
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri Apr 10 10:59:10 2015 +0300
drm/i915: Allocate connector state together with the connectors
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The btusb_read_local_version function has only a single user and with
that just move its functionality in place where it belongs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The __hci_cmd_sync function already handles the command status and
command complete errors. No need to check the status field again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
So, I'm told this problem exists in the world:
> Subject: Build error in -next due to 'efi: Add esrt support'
>
> Building ia64:defconfig ... failed
> --------------
> Error log:
>
> drivers/firmware/efi/esrt.c:28:31: fatal error: asm/early_ioremap.h: No such file or directory
>
I'm not really sure how it's okay that we have things in asm-generic on
some platforms but not others - is having it the same everywhere not the
whole point of asm-generic?
That said, ia64 doesn't have early_ioremap.h . So instead, since it's
difficult to imagine new IA64 machines with UEFI 2.5, just don't build
this code there.
To me this looks like a workaround - doing something like:
generic-y += early_ioremap.h
in arch/ia64/include/asm/Kbuild would appear to be more correct, but
ia64 has its own early_memremap() decl in arch/ia64/include/asm/io.h ,
and it's a macro. So adding the above /and/ requiring that asm/io.h be
included /after/ asm/early_ioremap.h in all cases would fix it, but
that's pretty ugly as well. Since I'm not going to spend the rest of my
life rectifying ia64 headers vs "generic" headers that aren't generic,
it's much simpler to just not build there.
Note that I've only actually tried to build this patch on x86_64, but
esrt.o still gets built there, and that would seem to demonstrate that
the conditional building is working correctly at all the places the code
built before. I no longer have any ia64 machines handy to test that the
exclusion actually works there.
Signed-off-by: Peter Jones <pjones@redhat.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
(Compile-)Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
struct timeval uses a 32-bit field for representing seconds, which
will overflow in the year 2038 and beyond. Replace struct timeval with
64-bit ktime_t which is 2038 safe. This is part of a larger effort to
remove instances of 32-bit timekeeping variables (timeval, time_t and
timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
MODULE_DEVICE_TABLE is referring to wrong driver's table and breaks the
build. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.
since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.
Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was missing and would cause issue in WMM handling.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would enable driver to enter powersave as soon as connected.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to parse power constraint IEs from
Tail buffer. This power constraint is then set to FW during
bss_config download.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support to disable ongoing CAC in FW upon
detecting radar during CAC period.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes an issue where we were still setting 11h_active
flag to true for channel defs where DFS is not required.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BSS reset would reset all state information in FW.
Issue 11d config command after reset to enabled 11d in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This would enable clearing of FW bss data structures when AP
operations are stopped.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct bss_type assignment in add_virtual_interface.
This would ensure correct operation in multiple station scenarios.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds more detailed information about association failures
- reason and states.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: 6058bb3628 'ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller'
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1433684009.9134.1.camel@ingics.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The SKB returned from the Intel specific version information command is
missing a kfree_skb.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Link failures have been observed when using the KSZ9031 with HP 1810-8G
and HP 1910-8G network switches. Center the FLP timing at 16ms to help
avoid intermittent link failures.
>From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section
"Auto-Negotiation Timing":
The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst
transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3
Standard specifies this timing to be 16ms +/-8ms. Some PHY link
partners need to receive the FLP with 16ms centered timing;
otherwise, there can be intermittent link failures and long
link-up times.
The PHY data sheet recommends configuring the FLP burst registers after
power-up/reset and immediately thereafter restarting auto-negotiation, so
we center the FLP timing at 16ms and then restart auto-negotiation in the
config_init for KSZ9031.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some defines for a few pad skew related extended registers.
Specify for which MMD Address (dev_addr) they are for.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few places in this driver, we weren't using const where we could
have. Use const more.
In addition, change the arrays of strings in ksz9031_config_init() to be
not only const, but also static.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
changed the behavior for how to assign the ocr_avail mask for the mmc
host. More precisely it started to mask the bits instead of assigning
them.
Restore the behavior, but also make it clear that an OCR mask created
from an external regulator overrides the other ones. The OCR mask is
determined by one of the following with this priority:
1. Supported ranges of external regulator if one supplies VDD
2. Host OCR mask if set by the driver (based on DT properties)
3. The capabilities reported by the controller itself
Fixes: 3a48edc4bd ("mmc: sdhci: Use mmc core regulator infrastucture")
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@gmail.com>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/dscc4.c:1036:1-33:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:554:2-34:
WARNING: timeout (10) seems HZ dependent
./drivers/net/wan/dscc4.c:599:2-34:
WARNING: timeout (10) seems HZ dependent
Numeric constants passed to schedule_timeout_*() make the effective
timeout HZ dependent which does not seem to be the intent here.
Fixed up by converting the constant to jiffies with msecs_to_jiffies(),
passing 100ms (assuming HZ==100 in the original code).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
API compliance scanning with coccinelle flagged:
./drivers/net/wan/cosa.c:520:2-18: WARNING:
timeout (30) seems HZ dependent
Numeric constants passed to schedule_timeout() make the effective
timeout HZ dependent which makes little sense in a device probe.
Fixed up by converting the constant to jiffies with msecs_to_jiffies()
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.
The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().
Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) and a broken_acpi_video quirk, whether or not
the acpi video bus event listener actually gets unregistered depends on
module load ordering:
Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
the listener and the acpi backlight interface
3) samsung-laptop.ko gets loaded, calls acpi_video_unregister() causing
both the listener and the acpi backlight interface to unregister
Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) samsung-laptop.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
calls acpi_video_unregister(), which is a nop since acpi_video_register
has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
the listener, but does not register the acpi backlight interface due to
the call to the preciding call to acpi_video_dmi_promote_vendor()
*) acpi/video.ko always loads first as both other modules depend on it.
So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.
Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.
Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!
On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com)
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.
The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().
Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) and a wmi_backlight_power quirk, whether or not
the acpi video bus event listener actually gets unregistered depends on
module load ordering:
Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
the listener and the acpi backlight interface
3) asus-wmi.ko gets loaded, calls acpi_video_unregister() causing both
the listener and the acpi backlight interface to unregister
Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) asus-wmi.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
calls acpi_video_unregister(), which is a nop since acpi_video_register
has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
the listener, but does not register the acpi backlight interface due to
the call to the preciding call to acpi_video_dmi_promote_vendor()
*) acpi/video.ko always loads first as both other modules depend on it.
So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.
Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.
Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!
On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.
Cc: acpi4asus-user@lists.sourceforge.net
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com)
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
acpi_video_unregister() not only unregisters the acpi-video backlight
interface but also unregisters the acpi video bus event listener, causing
e.g. brightness hotkey presses to no longer generate keypress events.
The unregistering of the acpi video bus event listener usually is
undesirable, which by itself is a good reason to switch to
acpi_video_unregister_backlight().
Another problem with using acpi_video_unregister() rather then using
acpi_video_unregister_backlight() is that on systems with an intel video
opregion (most systems) whether or not the acpi video bus event listener
actually gets unregistered depends on module load ordering:
Scenario a:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) intel.ko gets loaded, calls acpi_video_register() which registers both
the listener and the acpi backlight interface
3) apple-gmux.ko gets loaded, calls acpi_video_unregister() causing both
the listener and the acpi backlight interface to unregister
Scenario b:
1) acpi/video.ko gets loaded (*), does not do acpi_video_register as there
is an intel opregion.
2) apple-gmux.ko gets loaded, calls acpi_video_dmi_promote_vendor(),
calls acpi_video_unregister(), which is a nop since acpi_video_register
has not yet been called
2) intel.ko gets loaded, calls acpi_video_register() which registers
the listener, but does not register the acpi backlight interface due to
the call to the preciding call to acpi_video_dmi_promote_vendor()
*) acpi/video.ko always loads first as both other modules depend on it.
So we end up with or without an acpi video bus event listener depending
on module load ordering, not good.
Switching to using acpi_video_unregister_backlight() means that independ
of ordering we will always have an acpi video bus event listener fixing
this.
Note that this commit means that systems without an intel video opregion,
and systems which were hitting scenario a wrt module load ordering, are
now getting an acpi video bus event listener while before they were not!
On some systems this may cause the brightness hotkeys to start generating
keypresses while before they were not (good), while on other systems this
may cause the brightness hotkeys to generate multiple keypress events for
a single press (not so good). Since on most systems the acpi video bus is
the canonical source for brightness events I believe that the latter case
will needs to be handled on a case by case basis by filtering out the
duplicate keypresses at the other source for them.
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
pvpanic was not properly detected when _STA was missing.
ACPI 6.0 April 2015, 6.3.7 _STA (Status)
If a device object (including the processor object) does not have an
_STA object, then OSPM assumes that all of the above bits are set
(i.e., the device is present, enabled, shown in the UI, and
functioning).
Not adhering to the specification made pvpanic dormant under QEMU 2.3.
The original patch used acpi_bus_get_status_handle, which was not
being exported, so module build blew up; switch to acpi_bus_get_status
and use the status it populates.
Populated status is a bitfield so we can make the code self-documenting.
We do not check 'present' because 'enabled' has to be false in that case
by specification. Older QEMUs set 0xff to status and newer ones do 0xb.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dvhart@linux.intel.com: Merge acpi_bug_get_status fix to avoid bisect breakage]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>