Commit graph

287,481 commits

Author SHA1 Message Date
Corey Minyard
3d69d43baa ipmi: Fix multi-part message handling
Lots of little fixes for multi-part messages:

The values was not being re-initialized, if something went wrong
handling a multi-part message and it got left in a bad state, it
might be an issue.

The commands were not correct when issuing multi-part reads, the
code was not passing in the proper value for commands.  Also clean
up some minor formatting issues.

Get the block number from the right location, limit the maximum send
message size to 63 bytes and explain why, and fix some minor sylistic
issues.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 19:37:22 -05:00
Corey Minyard
9162052173 ipmi: Add alert handling to SSIF
The SSIF interface can optionally have an SMBus alert come in when
data is ready.  Unfortunately, the IPMI spec gives wiggle room to
the implementer to allow them to always have the alert enabled,
even if the driver doesn't enable it.  So implement alerts.
If you don't in this situation, the SMBus alert handling will
constantly complain.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 19:36:38 -05:00
Hidehiro Kawai
9f8127048a ipmi: Fix a problem that messages are not issued in run_to_completion mode
start_next_msg() issues a message placed in smi_info->waiting_msg
if it is non-NULL.  However, sender() sets a message to
smi_info->curr_msg and NULL to smi_info->waiting_msg in the context
of run_to_completion mode.  As the result, it leads an infinite
loop by waiting the completion of unissued message when leaving
dying message after kernel panic.

sender() should set the message to smi_info->waiting_msg not
curr_msg.

Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 19:33:49 -05:00
Corey Minyard
a182a4b2b3 ipmi: Report an error if ACPI _IFT doesn't exist
When probing an ACPI table, report a specific error, instead of just
returning an error, if _IFT doesn't exist.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 19:33:48 -05:00
Wei Yongjun
15c5725e6b ipmi: Remove unused including <linux/version.h>
Remove including <linux/version.h> that don't need it.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 19:33:28 -05:00
Gregory CLEMENT
489405fe5e rtc: armada38x: fix concurrency access in armada38x_rtc_set_time
While setting the time, the RTC TIME register should not be accessed.
However due to hardware constraints, setting the RTC time involves
sleeping during 100ms.  This sleep was done outside the critical section
protected by the spinlock, so it was possible to read the RTC TIME
register and get an incorrect value.  This patch introduces a mutex for
protecting the RTC TIME access, unlike the spinlock it is allowed to
sleep in a critical section protected by a mutex.

The RTC STATUS register can still be used from the interrupt handler but
it has no effect on setting the time.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>	[4.0]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-05-05 17:10:11 -07:00
Philippe De Muyter
4d61ff6b99 rtc: add rtc-abx80x, a driver for the Abracon AB x80x i2c rtc
This is a basic driver for the ultra-low-power Abracon AB x80x series of RTC
chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor/
battery charger.

[arnd@arndb.de: abx805 depends on i2c]
[alexandre.belloni@free-electrons.com: renam buffer from date to buf in abx80x_rtc_read_time()]
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-05-05 17:10:10 -07:00
Andrew Morton
99ebbd30e3 revert "zram: move compact_store() to sysfs functions area"
Revert commit c72c6160d9

It was intended to be a cosmetic change that w/o any functional change
and was part of a bigger change:

  http://lkml.iu.edu/hypermail/linux/kernel/1503.1/01818.html

Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-05-05 17:10:10 -07:00
David S. Miller
53ee1033ac iwlwifi:
* fix firmware API for -13.ucode
 * fix RSSI handling that avoid bad roaming decision
 * fix firmware debug
 * fix MFUART operation
 * fix ASSERT while restart the hardware (because of another ASSERT e.g)
 
 ath9k:
 
 * fix per-packet tx power configuration
 
 rtlwifi:
 
 * rtl8192cu: Fix kernel deadlock
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQEcBAABAgAGBQJVSPPDAAoJEG4XJFUm622bt7YIAI3OJuvLd/5uY0MddqKKJg8f
 G4LiNVFv6giD5KmH7vi0U3mic4iHGyUGOnC/7rmE31ZXxVWfFKRvALU8pR1wm8H3
 yMaEr1DabGIiGtJvHr9GDBCO4ALN3pAigzwCfV4L/NHKq0zui8Liz5fY33KhO7+p
 qnALX1stCXpy7aPSelysJqBWwc+JgipnKkkZbR3efrpWTNLMR69vsXXX/Kyj903x
 otYRbL9dRuOWrTvauyyTEbZ//Os1c78YG/nq7cT5COI/OP0Ao3W6p3QiHCz0Y3RE
 o4ACEHqxxziAY13bokyYEdlPjdl/xXORc5hi7qPAEsZbMW+7rtmZk6YIwUMFrxI=
 =H7p4
 -----END PGP SIGNATURE-----

Merge tag 'wireless-drivers-for-davem-2015-05-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* fix firmware API for -13.ucode
* fix RSSI handling that avoid bad roaming decision
* fix firmware debug
* fix MFUART operation
* fix ASSERT while restart the hardware (because of another ASSERT e.g)

ath9k:

* fix per-packet tx power configuration

rtlwifi:

* rtl8192cu: Fix kernel deadlock
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:41:33 -04:00
Yishai Hadas
2d3c739739 net/mlx4_core: Work properly with EQ numbers > 256 in SRIOV
The Firmware uses dynamic EQs allocation based on number of VFs and
max EQs that can be allocated. As a result, VF can have EQ numbers
that are larger than 256.

According to the firmware spec, the max value is limited to be 1024
(10 bits), adapt the relevant code accordingly. This bug was impossible
to hit prior to commit 7ae0e400cd ("net/mlx4_core: Flexible (asymmetric)
allocation of EQs and MSI-X vectors for PF/VFs") which actually enables
large number of EQs for VFs.

Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:39:12 -04:00
Eran Ben Elisha
cae0633872 net/mlx4_en: Fix off-by-one in counters manipulation
This caused the en_stats_adder helper to accumulate a field which is
not related to the counter, fix that.

Fixes: a3333b35da ('net/mlx4_en: Moderate ethtool callback to show [..]')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:39:12 -04:00
Thomas Graf
239fb791d4 vxlan: Correctly set flow*i_mark and flow4i_proto in route lookups
VXLAN must provide the skb mark and specifiy IPPROTO_UDP when doing
the FIB lookup for the remote ip. Otherwise an invalid route might
be returned.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:37:54 -04:00
Michal Simek
b0d081c524 net: axienet: Fix kernel-doc warnings
This patch remove kernel-doc warnings.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:34:01 -04:00
Srikanth Thokala
2be586205c net: axienet: Removed _of_ prefix in probe and remove functions
Synchronize names with other drivers.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:34:01 -04:00
Srikanth Thokala
8495659bf9 net: axienet: Use of_property_* calls
Use of_property_* calls

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:34:01 -04:00
Srikanth Thokala
46aa27df88 net: axienet: Use devm_* calls
use devm_* calls

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:34:00 -04:00
Srikanth Thokala
95219aa538 net: axienet: Use pdev instead of op
Synchronize names with other drivers

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:59 -04:00
Michal Simek
850a7503b0 net: axienet: Fix comments blocks
There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:59 -04:00
Srikanth Thokala
c81a97b5ca net: axienet: Removed coding style errors and warnings
Removed checkpatch.pl errors and warnings.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Srikanth Thokala
d7cc3163e0 net: axienet: Support phy-less mode of operation
This patch adds proper checks to handle the PHY-less case.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Srikanth Thokala
f080a8c35d net: axienet: Handle jumbo frames for lesser frame sizes
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Peter Crosthwaite
80c775accd net: axienet: Service completion interrupts ASAP
The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).

Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Peter Crosthwaite
38e96b35cd net: axienet: Handle 0 packet receive gracefully
The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.

This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.

Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.

Reported-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Srikanth Thokala
d1d372e8b7 net: axienet: Support for RGMII
This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.

Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:33:58 -04:00
Hariprasad Shenai
637d3e9973 cxgb4: Discard the packet if the length is greater than mtu
pktgen sends raw udp packets and bypasses most of the
linux networking stack. User can specify different packet sizes.
Hence we need to discard the packet if the length is greater than mtu

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:50 -04:00
Hariprasad Shenai
a3bfb6179c cxgb4: Move SGE Ingress DMA state monitor code to a new routine
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:50 -04:00
Hariprasad Shenai
982b81eb24 cxgb4: Add device node to ULD info
Adds device node to ULD info. Use the node info to alloc_ring() for ctrl
TX queues

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:50 -04:00
Hariprasad Shenai
b8b1ae990e cxgb4: Pass in a Congestion Channel Map to t4_sge_alloc_rxq()
Passes a Congestion Channel Map to t4_sge_alloc_rxq()
for the Ethernet RX Queues based on the MPS Buffer Group Map
of the TX Channel rather than just the TX Channel Map.
Also, in t4_sge_alloc_rxq() for T5, setting up the
Congestion Manager values of the new RX Ethernet Queue is
done by firmware now.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:49 -04:00
Hariprasad Shenai
145ef8a54e cxgb4: Enable congestion notification from SGE for IQs and FLs.
Also changed the name of t4_hw.c:get_mps_bg_map() to t4_get_mps_bg_map()
and make it an exported routine with a definition in cxgb4.h.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:49 -04:00
Hariprasad Shenai
1343299727 cxgb4: Make sure that Freelist size is larger than Egress Congestion Threshold
We need to make sure that the Free List Size, in pointers, is at
least 2 Egress Queue Units (8 pointers/each) larger than the SGE's Egress
Congestion Threshold (in pointers).

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:31:48 -04:00
Mahesh Bandewar
f631c44bbe ipvlan: Always set broadcast bit in multicast filter
Earlier tricks of setting broadcast bit only when IPv4 address is added
onto interface are not good enough especially when autoconf comes in play.
Setting them on always is performance drag but now that multicast /
broadcast is not processed in fast-path; enabling broadcast will let
autoconf work correctly without affecting performance characteristics of
the device.

Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:29:49 -04:00
Mahesh Bandewar
ba35f8588f ipvlan: Defer multicast / broadcast processing to a work-queue
Processing multicast / broadcast in fast path is performance draining
and having more links means more cloning and bringing performance
down further.

Broadcast; in particular, need to be given to all the virtual links.
Earlier tricks of enabling broadcast bit for IPv4 only interfaces are not
really working since it fails autoconf. Which means enabling broadcast
for all the links if protocol specific hacks do not have to be added into
the driver.

This patch defers all (incoming as well as outgoing) multicast traffic to
a work-queue leaving only the unicast traffic in the fast-path. Now if we
need to apply any additional tricks to further reduce the impact of this
(multicast / broadcast) type of traffic, it can be implemented while
processing this work without affecting the fast-path.

Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 19:29:49 -04:00
Jerry Snitselaar
7aab5159fa hv_netvsc: remove unused variable in netvsc_send()
With commit b56fc3c536 ("hv_netvsc: Fix a bug in netvsc_start_xmit()"),
skb variable is no longer used in netvsc_send. Remove variable and dead
code that depended on it.

Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-05-05 17:31:09 -04:00
Jean Delvare
df6dd1b35b thinkpad_acpi: Fix warning for static not at beginning
Fix the following warning:

warning: "static" is not at beginning of declaration
 void static hotkey_mask_warn_incomplete_mask(void)
 ^

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Henrique de Moraes Holschuh <ibm-acpi@hmh.eng.br>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
2015-05-05 13:56:46 -07:00
Lorenzo Pieralisi
bbf55ae19f ACPI / proc: make ACPI_PROCFS_POWER X86 only
The ACPI procfs power interface is initialized by compilation units
that are only selectable on X86 platforms. Since its usage is
deprecated and it cannot even be used on platforms other than X86
it should be compiled in only on X86 platforms.

This patch makes CONFIG_ACPI_PROCFS_POWER dependent on X86, so
that other architectures are prevented from compiling it in for
no purpose.

Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-05 22:34:44 +02:00
Fabian Frederick
fac69a2bc8 PNP / ACPI: use unsigned int in pnpacpi_encode_resources()
use unsigned int for port, irq, dma and mem used for pnp_get_resource()
This fixes gcc warnings of type "conversion to unsigned int
from int may change the sign of the result"

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-05 22:31:22 +02:00
Fabian Frederick
bbee06d067 PNP / ACPI: use u8 instead of int in acpi_resource_extended_irq context
acpi_resource_extented_irq variables are all u8.
Use that type for triggering, polarity and shareable.
This fixes gcc warnings of type
"conversion to u8 from int may alter its value"

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-05-05 22:31:21 +02:00
Ming Lei
4d4e41aef9 block: loop: avoiding too many pending per work I/O
If there are too many pending per work I/O, too many
high priority work thread can be generated so that
system performance can be effected.

This patch limits the max_active parameter of workqueue as 16.

This patch fixes Fedora 22 live booting performance
regression when it is booted from squashfs over dm
based on loop, and looks the following reasons are
related with the problem:

- not like other filesyststems(such as ext4), squashfs
is a bit special, and I observed that increasing I/O jobs
to access file in squashfs only improve I/O performance a
little, but it can make big difference for ext4

- nested loop: both squashfs.img and ext3fs.img are mounted
as loop block, and ext3fs.img is inside the squashfs

- during booting, lots of tasks may run concurrently

Fixes: b5dd2f6047
Cc: stable@vger.kernel.org (v4.0)
Cc: Justin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:46:55 -06:00
Ming Lei
f4aa4c7bba block: loop: convert to per-device workqueue
Documentation/workqueue.txt:
	If there is dependency among multiple work items used
	during memory reclaim, they should be queued to separate
	wq each with WQ_MEM_RECLAIM.

Loop devices can be stacked, so we have to convert to per-device
workqueue. One example is Fedora live CD.

Fixes: b5dd2f6047
Cc: stable@vger.kernel.org (v4.0)
Cc: Justin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:46:53 -06:00
Christoph Hellwig
9dc6c806b3 nbd: stop using req->cmd
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:40:44 -06:00
Christoph Hellwig
a7928c1578 block: move PM request support to IDE
This removes the request types and hacks from the block code and into the
old IDE driver.  There is a small amunt of code duplication due to this,
but it's not too bad.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:40:42 -06:00
Christoph Hellwig
b0b93b48a3 block: move REQ_TYPE_SENSE to the ide driver
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:40:07 -06:00
Christoph Hellwig
4f8c9510ba block: rename REQ_TYPE_SPECIAL to REQ_TYPE_DRV_PRIV
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:40:03 -06:00
Christoph Hellwig
84be456f88 remove <asm/scatterlist.h>
We don't have any arch specific scatterlist now that parisc switched over
to the generic one.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:35:39 -06:00
Jens Axboe
dac56212e8 bio: skip atomic inc/dec of ->bi_cnt for most use cases
Struct bio has a reference count that controls when it can be freed.
Most uses cases is allocating the bio, which then returns with a
single reference to it, doing IO, and then dropping that single
reference. We can remove this atomic_dec_and_test() in the completion
path, if nobody else is holding a reference to the bio.

If someone does call bio_get() on the bio, then we flag the bio as
now having valid count and that we must properly honor the reference
count when it's being put.

Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:32:49 -06:00
Jens Axboe
c4cf5261f8 bio: skip atomic inc/dec of ->bi_remaining for non-chains
Struct bio has an atomic ref count for chained bio's, and we use this
to know when to end IO on the bio. However, most bio's are not chained,
so we don't need to always introduce this atomic operation as part of
ending IO.

Add a helper to elevate the bi_remaining count, and flag the bio as
now actually needing the decrement at end_io time. Rename the field
to __bi_remaining to catch any current users of this doing the
incrementing manually.

For high IOPS workloads, this reduces the overhead of bio_endio()
substantially.

Tested-by: Robert Elliott <elliott@hp.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
2015-05-05 13:32:47 -06:00
Corey Minyard
b1e65e7153 ipmi: Don't report err in the SI driver for SSIF devices
Really ignore them by returning -ENODEV from the probe, but not
doing anything.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 14:24:46 -05:00
Joe Perches
5e33cd0c5a ipmi: Remove incorrect use of seq_has_overflowed
commit d6c5dc18d8 ("ipmi: Remove uses of return value of seq_printf")
incorrectly changed the return value of various proc_show functions
to use seq_has_overflowed().

These functions should return 0 on completion rather than 1/true
on overflow.  1 is the same as #define SEQ_SKIP which would cause
the output to not be emitted (skipped) instead.

This is a logical defect only as the length of these outputs are
all smaller than the initial allocation done by the seq filesystem.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 14:24:46 -05:00
Corey Minyard
b0e9aaa99d ipmi:ssif: Ignore spaces when comparing I2C adapter names
Some of the adapters have spaces in their names, but that's really
hard to pass in as a module or kernel parameters.  So ignore the
spaces.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 14:24:45 -05:00
Corey Minyard
d467f7a405 ipmi_ssif: Fix the logic on user-supplied addresses
Returning zero is success.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
2015-05-05 14:24:45 -05:00