We have a function (iwl_mvm_scan_size()) that can calculate the scan
size for both UMAC and LMAC scans. Use that function instead of
calculating manually for LMAC scan and sched scan.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't support -9.ucode so, all the released firmwares
support scheduled scan properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove unused struct iwl_scan_offload_req and enum
iwl_scan_offload_flags which are not used anymore. Rename
iwl_scan_offload_schedule to iwl_scan_schedule_lmac to make it clear
that this is for LMAC only. And fix a small typo.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previously there was a check that compared window->average_tpt
to some value, and if it was different - it set it to that
value. However, this value was already calculated and set in
_rs_collect_tx_data(), so the entire check is unneeded.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This adds support for configuring and retrieving the FW
monitor in MARBH mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Net-detect scans were using the same type as sched scan, which was
causing the driver to return -EBUSY and prevent the system from
suspending if there was an ongoing scheduled scan. To avoid this, add
a new type for net-detect and don't stop anything when it is
requested, so that the existing scheduled scan will be resumed when
the system wakes up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move all the scan code that was in mac80211.c to scan.c where it
belongs, leaving only the parts that are specific to mac80211 ops.
Change some function definitions slightly to improve consistency.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All scans are using the unified APIs now, so using "unified" in the
symbols is useless and just make them much longer and the main
difference between scans now is LMAC vs. UMAC. Remove "unified" from
all relevant symbols.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of hardcoding the differences between UMAC scans and LMAC
scans (which in this case is the number of simultaneous scans that can
run), introduce a max_scans variable and stop scans of the other type
(i.e. stop sched scan if regular scan is being attempted and
vice-versa) if the number of running scans reached the maximum.
Add a function that checks if the maximum number of scans was reached
and stops the appropriate scan to make room for the new scan.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If a new scan cannot be run for some reason, we shouldn't cancel other
ongoing scans. Move the checks to before the code that cancels other
scans.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Now that we have separate flags for stopping scans, we don't need to
wait for the scan stopped work to complete before starting the new
scan. Previously we needed it because we had no way of distinguishing
the scan that was being stopped from the scan that was currently
running. With the new flags there won't be any confusions and we are
able to handle the stop for the correct type of scan.
Thus we can remove the iwl_mvm_cancel_scan_wait_notif() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC scans cannot handle more than one scan at a time, but UMAC scans
can. To avoid confusion we should combine the states of these two
types of scans. To do so, we need to support mutliple scans at the
same time for UMAC.
This commit changes the scan_status element from a single value to a
bitmask of running scan types for LMAC. Later, we will modify UMAC
scans to use the same state bitmask.
Additionally, add stopping scan flags for scheduled and regular scans.
This makes it easier to differentiate and handle stop requests
triggered by the driver and spontaneous stops generated by the
firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases, max_out_time value is smaller than 200 and having the
NL80211_SCAN_FLAG_LOW_PRIORITY flag was actually causing the
max_out_time to be increased. To avoid that, set max_out_time to 200
only if it's greater than 200.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add scan parameters information to make it easier to debug scan dwell
times and fragmentation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
last_txrate_idx isn't used anymore and can be dropped as this info
exists already somewhere else.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Same code appear a few lines later while the position has
no effect on the actual flow.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When user space requests mac80211 to transmit a frame off
channel, mac80211 notifies the driver, and the driver requests
a time event from the ucode, and then transmits the frame.
When the driver requests a time event, it can specify what is the allowed
max delay for starting the time event.
When the max delay is too big, this can cause a timeout in the user space,
that is waiting for the frame to be transmitted.
Currently the max delay is extremely long.
Reduce the max delay for the AUX ROC time event that is sent to the ucode.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Commit 9faf6136ff (ACPI / SBS: Disable smart battery manager on
Apple) introduced a regression disabling the SBS battery manager.
The battery manager should be marked as present when
acpi_manager_get_info() returns 0.
Fixes: 9faf6136ff (ACPI / SBS: Disable smart battery manager on Apple)
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Split out the 32-bit SCM implementation into its own file to prep for
supporting a 64-bit/ARM64 implementation as well. We create a simple shim
to ensure both versions conform to the same interface.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).
Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.
See: https://www.exar.com/common/content/document.ashx?id=1587 page 11
Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware "board" file name has changed from wil6210.board
to wil6210.brd by the FW generation tools.
Reflect this in the driver.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.stop_ap supposed to have interface carried turned off as
post condition. Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trace where wil6210_disconnect() is called from.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull s390 updates from Martin Schwidefsky:
"One additional new feature for 4.1, a new PRNG based on SHA-512 for
the zcrypt driver.
Two memory management related changes, the page table reallocation for
KVM is removed, and with file ptes gone the encoding of page table
entries is improved.
And three bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/zcrypt: Introduce new SHA-512 based Pseudo Random Generator.
s390/mm: change swap pte encoding and pgtable cleanup
s390/mm: correct transfer of dirty & young bits in __pmd_to_pte
s390/bpf: add dependency to z196 features
s390/3215: free memory in error path
s390/kvm: remove delayed reallocation of page tables for KVM
kexec: allocate the kexec control page with KEXEC_CONTROL_MEMORY_GFP
The phy-rcar-gen2-usb driver, which supports legacy platform data only,
is no longer used since commit a483dcbfa2 ("ARM: shmobile: lager:
Remove legacy board support").
This driver was superseded by the DT-only phy-rcar-gen2 driver, which
was introduced in commit 1233f59f74 ("phy: Renesas R-Car Gen2 PHY
driver").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
VBUS is not routed to USB PHY on recent Qualcomm platforms. USB controller
must see VBUS in order to pull-up DP when setting RS bit. Henc configure
USB PHY and LINK registers sense VBUS and enable manual pullup on D+ line.
Cc: Vamsi Krishna <vskrishn@codeaurora.org>
Cc: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".
Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This WA is avoid problem between shadow vs wake FIFO unload
problem during CPD/RC6 transactions on CHV.
v2: Define individual bits GTFIFOCTL (Ville)
v3: move WA to uncore_early_sanitize (ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some whitespace issues while applying]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fix interpretation of the pmic_mpp_read() return code,
negative value means an error.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Read input buffer when input is enabled, not when it is
disabled. Also fix interpretation of the pmic_gpio_read()
return code, negative value means an error.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO output type configuration was incorrectly overwritten
by strength value. Fix this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
radio-bcm2048.c: In function 'bcm2048_i2c_driver_probe':
radio-bcm2048.c:2597:11: warning: variable 'skip_release' set but not used [-Wunused-but-set-variable]
int err, skip_release = 0;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In file included from include/uapi/linux/posix_types.h:4:0,
from include/uapi/linux/types.h:13,
from include/linux/types.h:5,
from include/uapi/linux/sysinfo.h:4,
from include/uapi/linux/kernel.h:4,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/input.h:11,
from drivers/media/usb/dvb-usb/dvb-usb.h:13,
from drivers/media/usb/dvb-usb/dib0700.h:13,
from drivers/media/usb/dvb-usb/dib0700_devices.c:9:
drivers/media/dvb-frontends/dib8000.h: In function 'dib8000_attach':
include/linux/stddef.h:8:14: warning: return makes integer from pointer without a cast [-Wint-conversion]
#define NULL ((void *)0)
^
drivers/media/dvb-frontends/dib8000.h:72:9: note: in expansion of macro 'NULL'
return NULL;
^
Reported-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes problems with serial console break. When function
s3c64xx_serial_startup() was started while serial console has been working,
it caused lose of characters written to TX FIFO. This effect was particularly
observable with systemd, which closes serial port every time when it's
not currently needed, hence function s3c64xx_serial_startup() is called
quite often there. To fix this problem we avoid resetting TX FIFO if port is
used as serial console.
Example of broken console log:
[ 1086.7 Expecting device dev-ttySAC1.device...
[ 1086.[ OK ] Reached target Paths.
[ 1086.756416] s[ OK ] Reached target Swap.
[ 1086.776413] systemd[1]: Reached target Swap.
[ 1086.776642] systemd[1]: Starting Root Slice.
[ 5.53403[ OK ] Created slice Root Slice.
[ 5.548433] systemd[1]: Create[ OK ] Created slice User and Session Slice.
[ 5.568414] sys[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 5.588388] s[ OK ] Listening on Delayed Shutdown Socket.
[ 5.608376] sy[ OK ] Listening on Journal Socket (/dev/log).
[ 5.628361] [ OK ] Listening on udev Kernel Socket.
[ 5.648357] s[ OK ] Listening on udev Control Socket.
[ 5.668353] s[ OK ] Listening on Journal Socket.
[ 5.688366] systemd[1]: Listeni[ OK ] Created slice System Slice.
[ 5.708393] Mounting Temporary Directory...
[ 7139.067436] Starting prepare device daemon...
[ 7139.091726] sy Starting Generate environment from /etc/profile.d...
[ 5.792867] system Starting Create Static Device Nodes in /dev...
[ 7848.718 Mounting Debug File System...
[ 7848.7384 Mounting Configuration File System...
[ 5.852 Starting Apply Kernel Variables...
[ 5.8720 Starting Setup Virtual Console...
[ 7848.798 Starting udev Coldplug all Devices...
[ 7848.817 Starting Journal Service...
[ OK ] Started Journal Service.
[ 7848.854222] s[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Configuration File System.
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not probe all serial drivers by of_serial.c which are using
device_type = "serial"; property. Only drivers which have valid
compatible strings listed in the driver should be probed.
When PORT_UNKNOWN is setup probe will fail anyway.
Arnd quotation about driver historical background:
"when I wrote that driver initially, the idea was that it would
get used as a stub to hook up all other serial drivers but after
that, the common code learned to create platform devices from DT"
This patch fix the problem with on the system with xilinx_uartps and
16550a where of_serial failed to register for xilinx_uartps and because
of irq_dispose_mapping() removed irq_desc. Then when xilinx_uartps was asking
for irq with request_irq() EINVAL is returned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For systems with CONFIG_SERIAL_OF_PLATFORM=y and device_type =
"serial"; property in DT of_serial.c driver maps and unmaps IRQ (because
driver probe fails). Then a driver is called but irq mapping is not
created that's why driver is failing again in again on request_irq().
Based on this use platform_get_irq() instead of platform_get_resource()
which is doing irq_desc allocation and driver itself can request IRQ.
Fix both xilinx serial drivers in the tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is needed by Bluetooth hci_uart module to be able to change speed
of Bluetooth controller and local UART.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:13:0:
drivers/media/dvb-frontends/cx24123.h:54:2: warning: 'cx24123_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
cx24123_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:46:0:
drivers/media/dvb-frontends/s921.h:40:2: warning: 's921_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
s921_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/em28xx/em28xx-dvb.c:55:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
In file included from drivers/media/usb/cx231xx/cx231xx-dvb.c:35:0:
drivers/media/dvb-frontends/mb86a20s.h:49:2: warning: 'mb86a20s_get_tuner_i2c_adapter' defined but not used [-Wunused-function]
mb86a20s_get_tuner_i2c_adapter(struct dvb_frontend *fe)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_power':
drivers/media/platform/s3c-camif/camif-capture.c:118:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.power_count)
^
drivers/media/platform/s3c-camif/camif-capture.c: In function 'sensor_set_streaming':
drivers/media/platform/s3c-camif/camif-capture.c:134:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == camif->sensor.stream_count)
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix these compiler warnings that appeared after switching to gcc-5.1.0:
drivers/media/i2c/s5k5baf.c: In function 's5k5baf_set_power':
drivers/media/i2c/s5k5baf.c:1057:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on != state->power)
^
drivers/media/i2c/s5k6aa.c: In function 's5k6aa_set_power':
drivers/media/i2c/s5k6aa.c:878:10: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
if (!on == s5k6aa->power) {
^
drivers/media/i2c/s5c73m3/s5c73m3-core.c: In function 's5c73m3_oif_set_power':
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1456:17: warning: logical not is only applied to the left hand side of comparison [-Wlogical-not-parentheses]
} else if (!on == state->power) {
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For these encodings the quantization range should be ignored, since
there is only one possible Y'CbCr encoding.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020_CONST_LUM.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_BT2020.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to be consistent with the other Y'CbCr encodings add
support for full range V4L2_YCBCR_ENC_SMPTE240M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a log_status function to the test pattern generator and use that
in vivid. This simplifies debugging complex colorspace problems.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>