Change the init flow to ask GUIDs only for active VFs. This is done for
both SM & HOST modes so that there is no need any more to maintain the
ownership record type.
In case SM mode is used, the initial value will be 0, ask the SM to assign,
for the HOST mode the initial value will be the HOST generated GUID.
This will enable out of the box experience for both probed and attached VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the admin alias GUID per the administrator's request via the sysfs
mechanism into the core layer.
The "get" request returns the current value. However, if the administrator
requests the SM to assign a new value by requesting 0, the SM assigned
GUID is returned.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To have out of the box experience, the PF generates random GUIDs who
serve as the initial admin values.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Manages alias GUIDs per VF per port in the core layer.
This is a pre-step for managing alias GUIDs in a mode that the admin
GUID is returned via ib_query_gid() regardless of whether the SM
has approved it or not.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the SM rejects an alias GUID request the PF driver keeps trying to acquire
the specified GUID indefinitely, utilizing an exponential backoff scheme.
Retrying is managed per GUID entry. Each entry that wasn't applied holds its
next retry information. Retry requests to the SM consist of records of 8
consecutive GUIDS. Each record that contains GUIDs requiring retries holds its
next time-to-run based on the retry information of all its GUID entries. The
record having the lowest retry time will run first when that retry time
arrives.
Since the method (SET or DELETE) as sent to the SM applies to all the GUIDs in
the record, we must handle SET requests and DELETE requests in separate SM
messages (one for SETs and the other for DELETEs).
To avoid race conditions where a GUID entry request (set or delete) was
modified after the SM request was sent, we save the method and the requested
indices as part of the callback's context -- thus, only the requested indexes
are evaluated when the response is received.
When an GUID entry is approved we turn off its retry-required bit, this
prevents redundant SM retries from occurring on that record.
The port down event should be sent only when previously it was up. Likewise,
the port up event should be sent only if previously the port was down.
Synchronization was added around the flows that change entries and record state
to prevent race conditions.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
that's the bulk of filesystem drivers dealing with inodes of their own
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix up some ->d_inode accesses in the chelsio driver.
(1) FILE_DATA() should just be replaced with file_inode().
(2) set_debugfs_file_size() should be removed and debugfs_create_file_size()
should be used to create the file.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Current -next fails to link an ARM allmodconfig because drivers that use
the core recovery functions can be built as modules but those functions
are not exported:
ERROR: "i2c_generic_gpio_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_generic_scl_recovery" [drivers/i2c/busses/i2c-davinci.ko] undefined!
ERROR: "i2c_recover_bus" [drivers/i2c/busses/i2c-davinci.ko] undefined!
Add exports to fix this.
Fixes: 5f9296ba21 (i2c: Add bus recovery infrastructure)
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull security subsystem updates from James Morris:
"Highlights for this window:
- improved AVC hashing for SELinux by John Brooks and Stephen Smalley
- addition of an unconfined label to Smack
- Smack documentation update
- TPM driver updates"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits)
lsm: copy comm before calling audit_log to avoid race in string printing
tomoyo: Do not generate empty policy files
tomoyo: Use if_changed when generating builtin-policy.h
tomoyo: Use bin2c to generate builtin-policy.h
selinux: increase avtab max buckets
selinux: Use a better hash function for avtab
selinux: convert avtab hash table to flex_array
selinux: reconcile security_netlbl_secattr_to_sid() and mls_import_netlbl_cat()
selinux: remove unnecessary pointer reassignment
Smack: Updates for Smack documentation
tpm/st33zp24/spi: Add missing device table for spi phy.
tpm/st33zp24: Add proper wait for ordinal duration in case of irq mode
smack: Fix gcc warning from unused smack_syslog_lock mutex in smackfs.c
Smack: Allow an unconfined label in bringup mode
Smack: getting the Smack security context of keys
Smack: Assign smack_known_web as default smk_in label for kernel thread's socket
tpm/tpm_infineon: Use struct dev_pm_ops for power management
MAINTAINERS: Add Jason as designated reviewer for TPM
tpm: Update KConfig text to include TPM2.0 FIFO chips
tpm/st33zp24/dts/st33zp24-spi: Add dts documentation for st33zp24 spi phy
...
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).
While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).
Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.1:
New interfaces:
- user-space interface for AEAD
- user-space interface for RNG (i.e., pseudo RNG)
New hashes:
- ARMv8 SHA1/256
- ARMv8 AES
- ARMv8 GHASH
- ARM assembler and NEON SHA256
- MIPS OCTEON SHA1/256/512
- MIPS img-hash SHA1/256 and MD5
- Power 8 VMX AES/CBC/CTR/GHASH
- PPC assembler AES, SHA1/256 and MD5
- Broadcom IPROC RNG driver
Cleanups/fixes:
- prevent internal helper algos from being exposed to user-space
- merge common code from assembly/C SHA implementations
- misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (169 commits)
crypto: arm - workaround for building with old binutils
crypto: arm/sha256 - avoid sha256 code on ARMv7-M
crypto: x86/sha512_ssse3 - move SHA-384/512 SSSE3 implementation to base layer
crypto: x86/sha256_ssse3 - move SHA-224/256 SSSE3 implementation to base layer
crypto: x86/sha1_ssse3 - move SHA-1 SSSE3 implementation to base layer
crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer
crypto: arm/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer
crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer
crypto: arm/sha1-ce - move SHA-1 ARMv8 implementation to base layer
crypto: arm/sha1_neon - move SHA-1 NEON implementation to base layer
crypto: arm/sha1 - move SHA-1 ARM asm implementation to base layer
crypto: sha512-generic - move to generic glue implementation
crypto: sha256-generic - move to generic glue implementation
crypto: sha1-generic - move to generic glue implementation
crypto: sha512 - implement base layer for SHA-512
crypto: sha256 - implement base layer for SHA-256
crypto: sha1 - implement base layer for SHA-1
crypto: api - remove instance when test failed
crypto: api - Move alg ref count init to crypto_check_alg
...
I suspect this doesn't show up for most anyone because software
algorithms typically don't have a sense of being too busy. However,
when working with the Freescale CAAM driver it will return -EBUSY on
occasion under heavy -- which resulted in dm-crypt deadlock.
After checking the logic in some other drivers, the scheme for
crypt_convert() and it's callback, kcryptd_async_done(), were not
correctly laid out to properly handle -EBUSY or -EINPROGRESS.
Fix this by using the completion for both -EBUSY and -EINPROGRESS. Now
crypt_convert()'s use of completion is comparable to
af_alg_wait_for_completion(). Similarly, kcryptd_async_done() follows
the pattern used in af_alg_complete().
Before this fix dm-crypt would lockup within 1-2 minutes running with
the CAAM driver. Fix was regression tested against software algorithms
on PPC32 and x86_64, and things seem perfectly happy there as well.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Commit 003b5c571 ("block: Convert drivers to immutable biovecs")
stopped short of changing dm-crypt to leverage the fact that the biovec
array of a bio will no longer be modified.
Switch to using bio_clone_fast() when cloning bios for decryption after
read.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cryptsetup home page moved to GitLab.
Also remove link to abandonded Truecrypt page.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Introduce a new target that is meant for file system developers to test file
system integrity at particular points in the life of a file system. We capture
all write requests and associated data and log them to a separate device
for later replay. There is a userspace utility to do this replay. The
idea behind this is to give file system developers a tool to verify that
the file system is always consistent.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Zach Brown <zab@zabbo.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add device specific modes to dm-verity to specify how corrupted
blocks should be handled. The following modes are defined:
- DM_VERITY_MODE_EIO is the default behavior, where reading a
corrupted block results in -EIO.
- DM_VERITY_MODE_LOGGING only logs corrupted blocks, but does
not block the read.
- DM_VERITY_MODE_RESTART calls kernel_restart when a corrupted
block is discovered.
In addition, each mode sends a uevent to notify userspace of
corruption and to allow further recovery actions.
The driver defaults to previous behavior (DM_VERITY_MODE_EIO)
and other modes can be enabled with an additional parameter to
the verity table.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This fixes up a compile warning [-Wunused-but-set-variable] - given the
comment in userspace_set_region_sync() the non-reporting of errors is
intentional so the return value can be dropped to make gcc happy.
Also, fix typo in comment.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Return type of wait_for_completion_timeout() is unsigned long not int.
An appropriately named unsigned long is added and the assignment fixed.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a device is used as the root filesystem, it can't be built
off of devices which are within the root filesystem (just like
command line arguments to root=). For this reason, Linux has a
pseudo-filesystem for root= and MD initialization (based on the
function name_to_dev_t) which handles different ways of specifying
devices including PARTUUID and major:minor.
Switch to using name_to_dev_t() in dm_get_device(). Rather than
having DM assume that all things which are not major:minor are paths in
an already-mounted filesystem, change dm_get_device() to first attempt
to look up the device in the filesystem, and if not found it will fall
back to using name_to_dev_t().
In terms of backwards compatibility, there are some cases where
behavior will be different:
- If you have a file in the current working directory named 1:2 and
you initialze DM there, then it will try to use that file rather
than the disk with that major:minor pair as a backing device.
- Similarly for other bdev types which name_to_dev_t() knows how to
interpret, the previous behavior was to repeatedly check for the
existence of the file (e.g., while waiting for rootfs to come up)
but the new behavior is to use the name_to_dev_t() interpretation.
For example, if you have a file named /dev/ubiblock0_0 which is
a symlink to /dev/sda3, but it is not yet present when DM starts
to initialize, then the name_to_dev_t() interpretation will take
precedence.
These incompatibilities would only show up in really strange setups
with bad practices so we shouldn't have to worry about them.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Request-based DM's blk-mq support defaults to off; but a user can easily
change the default using the dm_mod.use_blk_mq module/boot option.
Also, you can check what mode a given request-based DM device is using
with: cat /sys/block/dm-X/dm/use_blk_mq
This change enabled further cleanup and reduced work (e.g. the
md->io_pool and md->rq_pool isn't created if using blk-mq).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_mq_queue_rq() is in atomic context so care must be taken to not
sleep -- as such GFP_ATOMIC is used for the md->bs bioset allocations
and dm-mpath's call to blk_get_request(). In the future the bioset
allocations will hopefully go away (by removing support for partial
completions of bios in a cloned request).
Also prepare for supporting DM blk-mq ontop of old-style request_fn
device(s) if a new dm-mod 'use_blk_mq' parameter is set. The kthread
will still be used to queue work if blk-mq is used ontop of old-style
request_fn device(s).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit e5863d9ad ("dm: allocate requests in target when stacking on
blk-mq devices") served as the first step toward fully utilizing blk-mq
in request-based DM -- it enabled stacking an old-style (request_fn)
request_queue ontop of the underlying blk-mq device(s). That first step
didn't improve performance of DM multipath ontop of fast blk-mq devices
(e.g. NVMe) because the top-level old-style request_queue was severely
limited by the queue_lock.
The second step offered here enables stacking a blk-mq request_queue
ontop of the underlying blk-mq device(s). This unlocks significant
performance gains on fast blk-mq devices, Keith Busch tested on his NVMe
testbed and offered this really positive news:
"Just providing a performance update. All my fio tests are getting
roughly equal performance whether accessed through the raw block
device or the multipath device mapper (~470k IOPS). I could only push
~20% of the raw iops through dm before this conversion, so this latest
tree is looking really solid from a performance standpoint."
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Keith Busch <keith.busch@intel.com>
Otherwise, for sequential workloads, the dm_request_fn can allow
excessive request merging at the expense of increased service time.
Add a per-device sysfs attribute to allow the user to control how long a
request, that is a reasonable merge candidate, can be queued on the
request queue. The resolution of this request dispatch deadline is in
microseconds (ranging from 1 to 100000 usecs), to set a 20us deadline:
echo 20 > /sys/block/dm-7/dm/rq_based_seq_io_merge_deadline
The dm_request_fn's merge heuristic and associated extra accounting is
disabled by default (rq_based_seq_io_merge_deadline is 0).
This sysfs attribute is not applicable to bio-based DM devices so it
will only ever report 0 for them.
By allowing a request to remain on the queue it will block others
requests on the queue. But introducing a short dequeue delay has proven
very effective at enabling certain sequential IO workloads on really
fast, yet IOPS constrained, devices to build up slightly larger IOs --
yielding 90+% throughput improvements. Having precise control over the
time taken to wait for larger requests to build affords control beyond
that of waiting for certain IO sizes to accumulate (which would require
a deadline anyway). This knob will only ever make sense with sequential
IO workloads and the particular value used is storage configuration
specific.
Given the expected niche use-case for when this knob is useful it has
been deemed acceptable to expose this relatively crude method for
crafting optimal IO on specific storage -- especially given the solution
is simple yet effective. In the context of DM multipath, it is
advisable to tune this sysfs attribute to a value that offers the best
performance for the common case (e.g. if 4 paths are expected active,
tune for that; if paths fail then performance may be slightly reduced).
Alternatives were explored to have request-based DM autotune this value
(e.g. if/when paths fail) but they were quickly deemed too fragile and
complex to warrant further design and development time. If this problem
proves more common as faster storage emerges we'll have to look at
elevating a generic solution into the block core.
Tested-by: Shiva Krishna Merla <shivakrishna.merla@netapp.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Request-based DM's dm_request_fn() is so fast to pull requests off the
queue that steps need to be taken to promote merging by avoiding request
processing if it makes sense.
If the current request would've merged with previous request let the
current request stay on the queue longer.
Suggested-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 7eaceaccab ("block: remove per-queue plugging") didn't justify
DM's use of a 100ms delay; such an extended delay is a liability when
there is reason to re-kick the queue.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On really fast storage it can be beneficial to delay running the
request_queue to allow the elevator more opportunity to merge requests.
Otherwise, it has been observed that requests are being sent to
q->request_fn much quicker than is ideal on IOPS-bound backends.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The old dm_request() method used for q->make_request_fn had a branch for
request-based DM support but it isn't needed given that
dm_init_request_based_queue() sets it to the standard blk_queue_bio()
anyway.
Cleanup dm_init_md_queue() to be DM device-type agnostic and have
dm_setup_md_queue() properly finish queue setup based on DM device-type
(bio-based vs request-based).
A followup block patch can be made to remove the export for
blk_queue_bio() now that DM no longer calls it directly.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Fix:
drivers/i2c/busses/i2c-jz4780.c: In function 'jz4780_i2c_readw':
drivers/i2c/busses/i2c-jz4780.c:181:2: error:
implicit declaration of function 'readw'
drivers/i2c/busses/i2c-jz4780.c: In function 'jz4780_i2c_writew':
drivers/i2c/busses/i2c-jz4780.c:187:2: error:
implicit declaration of function 'writew'
seen with sparc64:allmodconfig and m68k:allmodconfig.
The driver has to include linux/io.h.
Fixes: ba92222ed6 ("i2c: jz4780: Add i2c bus controller driver
for Ingenic JZ4780")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Japan's W53 band requires 50% data traffic during its DFS test,
but WLAN baseband used by ath9k and ath10k is not able to achieve
current threshold rate, 50%, under the data traffic rate.
In other words, HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the rate.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Separate Japan's DFS pattern from FCC to control PPB threshold.
Currently all the radar detectors use the same threshold rate at
50%, but it's not able to achieve if data traffic rate is higher
than 40% because WLAN baseband used by ath9k and ath10k often fails
detecting radar pulses, so that SW cannot get enough radar reports
to achieve the rate.
Since Japan's W53 band requires 50% data traffic during its DFS
test we need to apply different threshold rate than others on it.
Hence define its own pattern to give flexibility to threshold rate.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.
Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.
This should improve P2P reliability a bit.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for new FCC DFS rules released on August 14, 2014.
FCC has added a new radar type named Radar Type 1 and original
Radar Type 1 is renamed to Radar Type 0 in consequence.
During the certificate test, Type 1 PRI values are randomly selected
within the range of 518 and 3066 and we divide it to 3 groups based on
practical test result data collected for more than a year.
For about Radar type ID, it does nothing to functionalities.
In other words, even if we re-order the IDs, DFS detection will
work as well, but we give the ID with matching to FCC doc.
By adding this support, the drivers using this DFS function are
able to support both of old and new FCC DFS rules simultaneously
without any other changes.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The DASD device driver prevents I/O from being started on stopped
devices. This also prevented channel paths to be verified and so
the device was unable to be resumed.
Fix by allowing path verification requests on stopped devices.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DASD device driver only has a limited amount of memory to build
I/O requests.
This memory was used by blocklayer requests leading to an inability
to build needed internal requests to resume the device.
Fix by preventing the DASD driver to fetch requests for a stopped
device.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Reference-ID: RQM 2520
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix ref counting for DASD devices leading to an inability to set a
DASD device offline.
Before a worker is scheduled the DASD device driver takes a reference
to the device. If the worker was already scheduled this reference was
never freed.
Fix by giving the reference to the DASD device free when
schedule_work() returns false.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 27356f54c8 ("mm/hotplug: verify hotplug memory range")
introduced a check that makes add_memory() only accept section size
aligned memory.
Therefore on z/VM systems, where standby memory is not aligned, no
standby memory is registered at all.
Example:
#cp def store 3504M standby 2336M
00: CP Q V STORE
00: STORAGE = 3504M MAX = 6G INC = 8M STANDBY = 2336M RESERVED = 0
For this setup the following error message is printed:
Section-unaligned hotplug range: start 0xdb000000, size 0x92000000
So fix this and register aligned memory in "sclp_cmd.c". This means
that for the corner cases where the standby memory is not aligned we
loose some memory.
In order to inform the user about the potential loss of standby memory,
we add a new message for each added standby block and print how
much of the standby memory is usable, for example:
sclp_cmd.4336b4: Standby memory at 0x50000000 (256M of 256M usable)
sclp_cmd.4336b4: Standby memory at 0xb0000000 (256M of 256M usable)
sclp_cmd.4336b4: Standby memory at 0xdb000000 (2048M of 2336M usable)
We also ensure that a potential memory block that contains both "assigned"
and "standby" memory cannot be setup offline.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the device being added to Xen is not contained in the ACPI table,
walk the PCI device tree to find a parent that is contained in the ACPI
table before finding the PXM information from this device.
Previously, it would try to get a handle for the device, then the
device's bridge, then the physfn. This changes the order so that it
tries to get a handle for the device, then the physfn, the walks up the
PCI device tree.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Originally Xen PV drivers only use single-page ring to pass along
information. This might limit the throughput between frontend and
backend.
The patch extends Xenbus driver to support multi-page ring, which in
general should improve throughput if ring is the bottleneck. Changes to
various frontend / backend to adapt to the new interface are also
included.
Affected Xen drivers:
* blkfront/back
* netfront/back
* pcifront/back
* scsifront/back
* vtpmfront
The interface is documented, as before, in xenbus_client.c.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Cc: Konrad Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
There was some mess in the dependencies in the pinctrl
Kconfig for compile tests under allmodconfig. Mea Culpa.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bump.
Change-ID: Id14baae72332d0f1a9bc5d351ea1a85cb0295ec3
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull ARM updates from Russell King:
"Included in this update are both some long term fixes and some new
features.
Fixes:
- An integer overflow in the calculation of ELF_ET_DYN_BASE.
- Avoiding OOMs for high-order IOMMU allocations
- SMP requires the data cache to be enabled for synchronisation
primitives to work, so prevent the CPU_DCACHE_DISABLE option being
visible on SMP builds.
- A bug going back 10+ years in the noMMU ARM94* CPU support code,
where it corrupts registers. Found by folk getting Linux running
on their cameras.
- Versatile Express needs an errata workaround enabled for CPU
hot-unplug to work.
Features:
- Clean up module linker by handling out of range relocations
separately from relocation cases we don't handle.
- Fix a long term bug in the pci_mmap_page_range() code, which we
hope won't impact userspace (we hope there's no users of the
existing broken interface.)
- Don't map DMA coherent allocations when we don't have a MMU.
- Drop experimental status for SMP_ON_UP.
- Warn when DT doesn't specify ePAPR mandatory cache properties.
- Add documentation concerning how we find the start of physical
memory for AUTO_ZRELADDR kernels, detailing why we have chosen the
mask and the implications of changing it.
- Updates from Ard Biesheuvel to address some issues with large
kernels (such as allyesconfig) failing to link.
- Allow hibernation to work on modern (ARMv7) CPUs - this appears to
have never worked in the past on these CPUs.
- Enable IRQ_SHOW_LEVEL, which changes the /proc/interrupts output
format (hopefully without userspace breaking... let's hope that if
it causes someone a problem, they tell us.)
- Fix tegra-ahb DT offsets.
- Rework ARM errata 643719 code (and ARMv7 flush_cache_louis()/
flush_dcache_all()) code to be more efficient, and enable this
errata workaround by default for ARMv7+SMP CPUs. This complements
the Versatile Express fix above.
- Rework ARMv7 context code for errata 430973, so that only Cortex A8
CPUs are impacted by the branch target buffer flush when this
errata is enabled. Also update the help text to indicate that all
r1p* A8 CPUs are impacted.
- Switch ARM to the generic show_mem() implementation, it conveys all
the information which we were already reporting.
- Prevent slow timer sources being used for udelay() - timers running
at less than 1MHz are not useful for this, and can cause udelay()
to return immediately, without any wait. Using such a slow timer
is silly.
- VDSO support for 32-bit ARM, mainly for gettimeofday() using the
ARM architected timer.
- Perf support for Scorpion performance monitoring units"
vdso semantic conflict fixed up as per linux-next.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (52 commits)
ARM: update errata 430973 documentation to cover Cortex A8 r1p*
ARM: ensure delay timer has sufficient accuracy for delays
ARM: switch to use the generic show_mem() implementation
ARM: proc-v7: avoid errata 430973 workaround for non-Cortex A8 CPUs
ARM: enable ARM errata 643719 workaround by default
ARM: cache-v7: optimise test for Cortex A9 r0pX devices
ARM: cache-v7: optimise branches in v7_flush_cache_louis
ARM: cache-v7: consolidate initialisation of cache level index
ARM: cache-v7: shift CLIDR to extract appropriate field before masking
ARM: cache-v7: use movw/movt instructions
ARM: allow 16-bit instructions in ALT_UP()
ARM: proc-arm94*.S: fix setup function
ARM: vexpress: fix CPU hotplug with CT9x4 tile.
ARM: 8276/1: Make CPU_DCACHE_DISABLE depend on !SMP
ARM: 8335/1: Documentation: DT bindings: Tegra AHB: document the legacy base address
ARM: 8334/1: amba: tegra-ahb: detect and correct bogus base address
ARM: 8333/1: amba: tegra-ahb: fix register offsets in the macros
ARM: 8339/1: Enable CONFIG_GENERIC_IRQ_SHOW_LEVEL
ARM: 8338/1: kexec: Relax SMP validation to improve DT compatibility
ARM: 8337/1: mm: Do not invoke OOM for higher order IOMMU DMA allocations
...