Commit graph

287,481 commits

Author SHA1 Message Date
Masanari Iida
dff1eb047f ACPI/PMIC: Fix typo in MODULE_DESCRIPTION in intel_pmic_crc.c
This patch fix a spelling typo in MODULE_DESCRIPTION within intel_pmic_crc.c

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2015-03-26 21:34:51 +01:00
Richard Weinberger
d59f21bebe UBI: Fastmap: Fix races in ubi_wl_get_peb()
ubi_wl_get_peb() has two problems, it reads the pool
size and usage counters without any protection.
While reading one value would be perfectly fine it reads multiple
values and compares them. This is racy and can lead to incorrect
pool handling.
Furthermore ubi_update_fastmap() is called without wl_lock held,
before incrementing the used counter it needs to be checked again.
It could happen that another thread consumed all PEBs from the
pool and the counter goes beyond ->size.

Signed-off-by: Richard Weinberger <richard@nod.at>
2015-03-26 21:24:24 +01:00
Richard Weinberger
399a9feeac UBI: Fastmap: Ensure that all fastmap work is done upon WL shutdown
...otherwise the deferred work might run after datastructures
got freed and corrupt memory.

Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
2015-03-26 19:31:26 +01:00
Richard Weinberger
19371d73c9 UBI: Fastmap: Ensure that only one fastmap work is scheduled
If the WL pool runs out of PEBs we schedule a fastmap write
to refill it as soon as possible.
Ensure that only one at a time is scheduled otherwise we might end in
a fastmap write storm because writing the fastmap can schedule another
write if bitflips are detected.

Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
2015-03-26 19:30:54 +01:00
Kishon Vijay Abraham I
cdf61240e1 bus: ocp2scp: SYNC2 value should be changed to 0x6
As per the TRMs of AM572x, OMAP4430, OMAP4460, OMAP543x, the value of
SYNC2 must be set to 0x6 in order to ensure correct operation.

So modified the SYNC2 value of OCP2SCP TIMING register to 0x6 in all the
platforms that use OCP2SCP driver except AM437x. Also introduced a new
compatible property since we don't want to modify the OCP2SCP TIMING
register for AM437x.

The sections in TRM where the above caution can be found is mentioned below.
AM572x TRM SPRUHZ6 (http://www.ti.com/lit/ug/spruhz6/spruhz6.pdf) under
section 26.3.2.2, table 26-26.

OMAP4430 TRM SWPU231AP (http://www.ti.com/lit/ug/swpu231ap/swpu231ap.pdf)
under section 23.12.6.2.2 , Table 23-1213.

OMAP4460 TRM SWPU235AB (http://www.ti.com/lit/ug/swpu235ab/swpu235ab.pdf)
under section 23.12.6.2.2, Table 23-1213.

OMAP543x TRM SWPU249 (http://www.ti.com/lit/pdf/swpu249)
under section 27.3.2.2, Table 27-27.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-03-26 10:48:11 -07:00
Peter Hurley
72a33aad47 serial: 8250: Declare base port operations const
The base port operations dispatch table should never be modified
at runtime; the proper way to override base port operations is
to dup the port operations, modify the copy, and point port->ops
at the copy.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:18:54 +01:00
Peter Hurley
4037539370 serial: 8250: Decouple RSA probe
Prepare for 8250 split; separate RSA probe and resource management
from base port operations. Override base port operations for the
config_port(), request_port() and release_port() methods to
implement the optional RSA probe and resource management only in
the universal/legacy 8250 driver.

Introduce 'probe' flags for 8250 ports, which allows drivers higher
up the driver stack to enable optional probes.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:18:20 +01:00
Peter Hurley
3b81c26c92 serial: 8250: Only get RSA resource when required
The probe for Remote Supervisor Adapter is limited to port i/o
addresses which match one of the probe_rsa[] module parameter
addresses. Limit RSA resource acquire to matching i/o ports.

The result is a saner probe policy: only perform optional probes
when specified rather than by default.

NB: It is possible for userspace to set the port type == PORT_RSA
with ioctl(TIOCSSERIAL) and then autoconfig with ioctl(TIOCSERCONFIG),
which if it fails, may leave the port type set to PORT_RSA. Since
this may have previously resulted in a working RSA port, this behavior
is preserved.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:18:20 +01:00
Peter Hurley
cd52b7599c serial: 8250: Get RSA resource iff CONFIG_SERIAL_8250_RSA
Support for Remote Supervisor Adapter is conditional on
CONFIG_SERIAL_8250_RSA; only attempt RSA resource acquire if
defined.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:18:20 +01:00
Peter Hurley
d53e1428a9 serial: 8250: Initialize default dma handlers when setting defaults
Prepare for 8250 split; move default dma tx/rx handler initialization
into serial8250_set_defaults(), which allows default dma ops to
remain unexported from the base port operations module after the split.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:18:20 +01:00
Peter Hurley
afd483bd0f serial: 8250: Initialize fixed type fields when setting defaults
Prepare for 8250 split; move fixed type initialization into
serial8250_set_defaults(). This enables uart_config[] array to remain
file scope in base port operations after the split.

NB: the call to serial8250_init_fixed_type_port() from
serial8250_register_ports() was added by commit b5d228cc4f
("serial: copy UART properties of UPF_FIXED_TYPE ports provisioned
using early_serial_setup") specifically to support ports initialized
by early_serial_setup(). Since serial8250_set_defaults() is called
from early_serial_setup(), fixed type initialization is now already
handled there before serial8250_register_ports() is called.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:17:36 +01:00
Peter Hurley
1a53e07989 serial: 8250: Encapsulate port i/o method init
Prepare for 8250 split; introduce serial8250_set_defaults() to set default
port methods prior to driver override.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:17:35 +01:00
Peter Hurley
0a16e2c1a6 serial: 8250: Separate port initialization
Prepare for 8250 split; introduce serial8250_init_port() to initialize
port fields uncoupled from port structure storage.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:17:35 +01:00
Peter Hurley
a4416cd1ac serial: 8250: Separate legacy irq handling from core port operations
Prepare for 8250 split; decouple irq setup/teardown and handler from
core port operations.

Introduce setup_irq() and release_irq() 8250 driver methods; the 8250
core will use these methods to install and remove irq handling for
the given 8250 port.

Refactor irq chain linking/unlinking from 8250 core into
univ8250_setup_irq()/univ8250_release_irq() for the universal 8250 driver.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:15:16 +01:00
Peter Hurley
6e28157173 serial: 8250: Separate 8250 console interface
Prepare for 8250 core split; separate shared console interface from the
console definition of the universal driver.

Introduce 8250 shared console interface; serial8250_console_write() and
serial8250_console_setup() which decouples the console operation from
the port structure storage.

Rename existing serial8250_console* identifiers to univ8250_console*.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 18:13:59 +01:00
Ander Conselvan de Oliveira
d21bd67bbb drm/i915: Don't use encoder->new_crtc in intel_lvds_compute_config()
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 18:00:48 +01:00
Ander Conselvan de Oliveira
e75f4771f8 drm/i915: Don't use staged config in intel_dp_mst_compute_config()
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 18:00:18 +01:00
Ander Conselvan de Oliveira
3165c07417 drm/i915: Use atomic state in intel_ddi_crtc_get_new_encoder()
Instead of using connector->new_encoder, get the same information from
the pipe_config, thus making the function ready for the atomic
conversion.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:57:55 +01:00
Ander Conselvan de Oliveira
77f06c8662 drm/i915: Don't depend on encoder->new_crtc in intel_hdmi_compute_config
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:52:33 +01:00
Ander Conselvan de Oliveira
84556d58ef drm/i915: Don't depend on encoder->new_crtc in intel_dp_compute_config()
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:50:08 +01:00
Ander Conselvan de Oliveira
1486017fbf drm/i915: Don't use encoder->new_crtc in compute_baseline_pipe_bpp()
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Keep the if (!connector) continue; separate so that it's
easier to eventually extract a for_each_connector_in_state iterator.
And because of the upcast it's also safer.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:49:53 +01:00
Ander Conselvan de Oliveira
0b90187939 drm/i915: Don't use encoder->new_crtc in intel_modeset_pipe_config()
Move towards atomic by using the legacy modeset's drm_atomic_state
instead.

v2: Move call to drm_atomic_add_affected_connectors() to
    intel_modeset_compute_config(). (Daniel)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Resurrect the ret local variable which I've dropped from an
earlier patch and which is now needed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:49:52 +01:00
Ander Conselvan de Oliveira
944b0c7657 drm/i915: Copy the staged connector config to the legacy atomic state
With this in place, we can start converting pieces of the modeset code
to look at the connector atomic state instead of the staged config.

v2: Handle the load detect staged config changes too. (Ander)
    Remove unnecessary blank line. (Daniel)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:49:51 +01:00
Ander Conselvan de Oliveira
d29b2f9dce drm/i915: Update dummy connector atomic state with current config
Keep that state updated so that we can write code that depends on it on
the follow up patches.

v2: Fix BUG due to stale connector_state->crtc value. (Chandra)

v3: Update comment about dummy state connectors. (Chandra)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 17:49:51 +01:00
Peter Hurley
df519e7bd3 serial: 8250_early: Remove setup_early_serial8250_console()
setup_earlycon() will now match and register the desired earlycon
from the param string (as if 'earlycon=...' had been set on the
command line). Use setup_earlycon() from existing arch call sites
which start an earlycon directly.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 17:25:27 +01:00
Peter Hurley
470ca0de69 serial: earlycon: Enable earlycon without command line param
Earlycon matching can only be triggered if 'earlycon=...' has been
specified on the kernel command line. To workaround this limitation
requires tight coupling between arches and specific serial drivers
in order to start an earlycon. Devicetree avoids this limitation
with a link table that contains the required data to match earlycons.

Mirror this approach for earlycon match by name. Re-purpose
EARLYCON_DECLARE to generate a table entry which associates name with
setup() function. Re-purpose setup_earlycon() to scan this table for
an earlycon match, which is registered if found.

Declare one "earlycon" early_param, which calls setup_earlycon().

This design allows setup_earlycon() to be called directly with a
param string (as if 'earlycon=...' had been set on the command line).
Re-registration (either directly or by early_param) is prevented.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 17:25:27 +01:00
Peter Hurley
7c53cb3de4 serial: earlycon: Refactor earlycon registration
Separate earlycon matching from registration; add register_earlycon
which initializes and registers the matched earlycon.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 17:25:27 +01:00
Peter Hurley
6084688038 serial: earlycon: Skip parse_options() if empty string
Earlycon param strings of the form
   earlycon=<name>
are rejected from parse_options() with an error (which, in turn,
results in a NULL argument for the setup() method options parameter).

Only pass non-empty string to parse_options(); this will enable
handling actual parse errors differently than expected and allow
formats.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 17:25:27 +01:00
Ander Conselvan de Oliveira
989697255d drm/i915: Implement connector state duplication
So that we can add connector states to the drm_atomic_state used in the
legacy modeset.

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 16:28:21 +01:00
kbuild test robot
2f0b57901b drm/i915/skl: fix semicolon.cocci warnings
drivers/gpu/drm/i915/intel_pm.c:2913:4-5: Unneeded semicolon

 Removes unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

CC: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 16:21:41 +01:00
Ander Conselvan de Oliveira
db7542dd40 drm/i915: Allocate a crtc_state also when the crtc is being disabled
For consistency, allocate a new crtc_state for a crtc that is being
disabled. Previously only the enabled value of the current state would
change.

v2: Rebase on v5 of previous patch. (Ander)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Resolve rebase conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 16:18:20 +01:00
Peter Hurley
526ebc3f56 serial: earlycon: Ignore parse_options() error code
Because setup_earlycon() continues to attempt console registration
if an error occurred parsing the option string, the actual value of
the error code from parse_options() is ignored.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:17:56 +01:00
Peter Hurley
cd385e9a2a serial: 8250_early: Fix setup() error code
If parsing failed to decode a valid uart addr, return -ENODEV instead
of success. Although setup_earlycon() will detect the failure anyway
(because the write() method has not been set), that behavior is not
obvious and should not be relied on.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:17:55 +01:00
Peter Hurley
0e3e143e5d serial: 8250_early: Assume uart already initialized if no baud option
The <baud><parity><bit> option string is not supplied if the earlycon
is started via devicetree and OF_EARLYCON_DECLARE(). The option string
is also not required if started via kernel command line parameters of
the form:
  earlycon=uart,mmio,<addr>
  console=uart,mmio,<addr>

If earlycon_device->baud is 0, then an option string was not supplied.
In this case, assume the uart has already been initialized by the
bootloader or firmware.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:17:55 +01:00
Peter Hurley
feed5bab0d serial: earlycon: Move ->uartclk initialize
Initializing the ->uartclk field is not related to option parsing;
relocate from parse_options() to setup_earlycon() (which mirrors the
behavior of of_setup_earlycon()).

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:17:55 +01:00
Peter Hurley
d0d654ce53 serial: 8250_early: Remove early_device variable
early_device was only required for serial8250_find_port_for_earlycon(),
which was replaced by extensible console matching.

Fixup early_serial8250_write() to get the earlycon_device * from
console->data (which is initialized by {of_}setup_earlycon()).

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:16:20 +01:00
Peter Hurley
1cfe42b7fd serial: core: Fix kernel doc for uart_console_write()
'/**' is required to start a kernel-doc comment block.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:16:20 +01:00
Peter Hurley
c7cef0a849 console: Add extensible console matching
Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).

The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.

Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:16:20 +01:00
Ander Conselvan de Oliveira
83a57153f5 drm/i915: Allocate a drm_atomic_state for the legacy modeset code
For the atomic conversion, the mode set paths need to be changed to rely
on an atomic state instead of using the staged config. By using an
atomic state for the legacy code, we will be able to convert the code
base in small chunks.

v2: Squash patch that adds stat argument to intel_set_mode(). (Ander)
    Make every caller of intel_set_mode() allocate state. (Daniel)
    Call drm_atomic_state_clear() in set config's error path. (Daniel)

v3: Copy staged config to atomic state in force restore path. (Ander)

v4: Don't update ->new_config for disabled pipes in __intel_set_mode(),
    since it is expected to be NULL in that case. (Ander)

v5: Don't change return type of intel_modeset_pipe_config(). (Chandra)

Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Remove spurious ret local variable due to changes in v5.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-26 16:15:34 +01:00
Peter Hurley
e13cb72bee serial: 8250: Decouple core from skip_txen_test module param
Prepare for 8250 split; initialize the port flags based on the
"skip_txen_test" module param to use the existing flag test.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:14:27 +01:00
Peter Hurley
d81e50f616 serial: 8250: Move ns16550a_goto_hispeed() to local header
Prepare for 8250_core.c file split; move shared inline function
to local header file.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:14:27 +01:00
Peter Hurley
5db496b9c8 serial: 8250: Simplify capabilities reset at port unregister
Since uart->port.type has just reset to PORT_UNKNOWN, capabilities
are reset to uart_config[PORT_UNKNOWN].flags, which is 0.

Removes unnecessary dependency on uart_config[].

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:14:27 +01:00
Peter Hurley
e6e98ceff3 serial: 8250: Remove duplicate ->handle_irq initialization
set_io_from_upio() already initializes ->handle_irq to
serial8250_default_handle_irq.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:14:27 +01:00
Peter Hurley
51c39814b6 serial: 8250: Compute ttyS index from port minor
Prepare for 8250 split; calculate the ttyS index directly from
the port minor which avoids the global serial8250_reg reference
from base port operations.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-26 16:14:27 +01:00
Lorenzo Pieralisi
d8f4f161e3 ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
The code deployed to implement GSI linux IRQ numbers mapping on arm64 turns
out to be generic enough so that it can be moved to ACPI core code along
with its respective config option ACPI_GENERIC_GSI selectable on
architectures that can reuse the same code.

Current ACPI IRQ mapping code is not integrated in the kernel IRQ domain
infrastructure, in particular there is no way to look-up the
IRQ domain associated with a particular interrupt controller, so this
first version of GSI generic code carries out the GSI<->IRQ mapping relying
on the IRQ default domain which is supposed to be always set on a
specific architecture in case the domain structure passed to
irq_create/find_mapping() functions is missing.

This patch moves the arm64 acpi functions that implement the gsi mappings:

acpi_gsi_to_irq()
acpi_register_gsi()
acpi_unregister_gsi()

to ACPI core code. Since the generic GSI<->domain mapping is based on IRQ
domains, it can be extended as soon as a way to map an interrupt
controller to an IRQ domain is implemented for ACPI in the IRQ domain
layer.

x86 and ia64 code for GSI mappings cannot rely on the generic GSI
layer at present for legacy reasons, so they do not select the
ACPI_GENERIC_GSI config options and keep relying on their arch
specific GSI mapping layer.

Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:09 +00:00
Graeme Gregory
b6a0217371 ARM64 / ACPI: Enable ARM64 in Kconfig
Add Kconfigs to build ACPI on ARM64, and make ACPI available on ARM64.

acpi_idle driver is x86/IA64 dependent now, so make CONFIG_ACPI_PROCESSOR
depend on X86 || IA64, and implement it on ARM64 in the future.

CC: Rafael J. Wysocki <rjw@rjwysocki.net>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Will Deacon <will.deacon@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:08 +00:00
Hanjun Guo
42068cfd65 XEN / ACPI: Make XEN ACPI depend on X86
When ACPI is enabled on ARM64, XEN ACPI will also compiled
into the kernel, but XEN ACPI is x86 dependent, so introduce
CONFIG_XEN_ACPI to make it depend on x86 before XEN ACPI is
functional on ARM64.

CC: Julien Grall <julien.grall@linaro.org>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: David Vrabel <david.vrabel@citrix.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:08 +00:00
Hanjun Guo
b09ca1ecf6 clocksource / arch_timer: Parse GTDT to initialize arch timer
Using the information presented by GTDT (Generic Timer Description Table)
to initialize the arch timer (not memory-mapped).

CC: Daniel Lezcano <daniel.lezcano@linaro.org>
CC: Thomas Gleixner <tglx@linutronix.de>
Originally-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:07 +00:00
Tomasz Nowicki
d60fc3892c irqchip: Add GICv2 specific ACPI boot support
ACPI kernel uses MADT table for proper GIC initialization. It needs to
parse GIC related subtables, collect CPU interface and distributor
addresses and call driver initialization function (which is hardware
abstraction agnostic). In a similar way, FDT initialize GICv1/2.

NOTE: This commit allow to initialize GICv1/2 basic functionality.
While now simple GICv2 init call is used, any further GIC features
require generic infrastructure for proper ACPI irqchip initialization.
That mechanism and stacked irqdomains to support GICv2 MSI/virtualization
extension, GICv3/4 and its ITS are considered as next steps.

CC: Jason Cooper <jason@lakedaemon.net>
CC: Marc Zyngier <marc.zyngier@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:07 +00:00
Hanjun Guo
fbe61ec71a ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
Introduce ACPI_IRQ_MODEL_GIC which is needed for ARM64 as GIC is
used, and then register device's gsi with the core IRQ subsystem.

acpi_register_gsi() is similar to DT based irq_of_parse_and_map(),
since gsi is unique in the system, so use hwirq number directly
for the mapping.

We are going to implement stacked domains when GICv2m, GICv3, ITS
support are added.

CC: Marc Zyngier <marc.zyngier@arm.com>
Originally-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Yijing Wang <wangyijing@huawei.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Timur Tabi <timur@codeaurora.org>
Tested-by: Robert Richter <rrichter@cavium.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2015-03-26 15:13:07 +00:00