Commit graph

287,481 commits

Author SHA1 Message Date
Brian Norris
dc52499e7f mtd: docg3: drop dead code
If no devices were found, we would already have skipped over this code.

Detected by Coverity, CID #744270

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
2015-03-11 15:21:19 -07:00
Uwe Kleine-König
98ebb52109 mtd: mxc-nand: Warn on unimplemented commands
The PARAM command was long unimplemented and it probably wasn't
noticed because chip probing using only the few bytes returned by the
READID command are good enough in most cases to determine the chip in
use.

Still to notice such a shortcoming earlier in the future would be nice
in case it's something more vital.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:42 -07:00
Uwe Kleine-König
3d6e81c0c9 mtd: mxc-nand: Implement support for PARAM command
The mxc-nand driver never supported the PARAM command to read out the
ONFI parameter page and so always relied on probing my manufacturer and
device id (as provided by the READID command).

This patch implements reading out the first parameter page copy at least
which should be good enough in practise.

This makes the boot log change from

	nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
	nand: Micron NAND 128MiB 1,8V 16-bit

to
	nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
	nand: Micron MT29F1G16ABBDAH4

on my machine.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:41 -07:00
Uwe Kleine-König
c4ca3997ef mtd: mxc-nand: Allow to use column addresses different from 0
The mxc-nand controller works pagewise and so usually only sends
commands to the flash chip with column == 0. A request with column != 0
from the upper layer is then fulfilled by indexing appropriately into the
device's RAM buffer.

To be able to access the ONFI marker at offset 0x20 in reply to the
READID command however it's invalid to read 32 bytes starting from
column 0.

So let the function used to send the address cycles send the column
address actually passed instead of 0 and fix all callers to pass 0
instead appropriately. Also add some warnings in case this patch changes
the drivers semantics.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:29 -07:00
Uwe Kleine-König
3f410690f5 mtd: mxc-nand: Do the word to byte mangling in the read_byte callback
When the hardware operates in 16 bit mode it always reads 16 bits even
for operations that only have the lower 8 bits defined. So the upper
bits must be discarded. Do this in the read_byte callback instead of
when reading the NAND id to support reading byte wise more than 5 bytes
and at other occations (like reading the ONFI parameter page).

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:29 -07:00
Uwe Kleine-König
1f42adc888 mtd: mxc-nand: Only enable hardware checksumming for fully detected flashes
At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.

Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:19 -07:00
Uwe Kleine-König
e35d1d8a1d mtd: mxc-nand: Add a timeout when waiting for interrupt
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 15:20:11 -07:00
Florian Fainelli
33d6737761 of: mdio: export of_mdio_parse_addr
Export of_mdio_parse_addr() which allows parsing a given Ethernet PHY
node MDIO address, verify it is within the allowed range, and return
its value. This is going to be useful for the DSA code which needs to
deal with multiple layers of MDIO buses.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-11 17:56:28 -04:00
Petri Gynther
d26ea6cc48 net: bcmgenet: collect Rx discarded packet count
Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.

Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-11 17:54:55 -04:00
Rob Clark
0e3704c94c drm/fb: handle tiled connectors better
We don't want tile 0,0 to artificially constrain the size of the legacy
fbdev device.  Instead when reducing fb_size to be the minimum of all
displays, only consider the rightmost and bottommost tiles.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Hai Li <hali@codeaurora.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:10:11 +01:00
Rob Clark
675c8328db drm/fb: small cleanup
Flip conditional to reduce indentation level of rest of fxn, and use
min/max to make the code clearer.

v2: surface_width -> surface_height typo

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:09:39 +01:00
Rob Clark
d3c8ea3460 drm/rockchip: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:08:25 +01:00
Rob Clark
ecbf1d5afe drm/exynos: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:08:17 +01:00
Rob Clark
8d76612bd4 drm/cma: use correct fb width/height
What is passed to drm_fb_helper_fill_var() should be fb_width/fb_height,
rather than the surface size.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:08:07 +01:00
Simon Farnsworth
1d002fa720 drm/dp: Use large transactions for I2C over AUX
Older DisplayPort to DVI-D Dual Link adapters designed by Bizlink have bugs
in their I2C over AUX implementation (fixed in newer revisions). They work
fine with Windows, but fail with Linux.

It turns out that they cannot keep an I2C transaction open unless the
previous read was 16 bytes; shorter reads can only be followed by a zero
byte transfer ending the I2C transaction.

Copy Windows's behaviour, and read 16 bytes at a time. If we get a short
reply, assume that there's a hardware bottleneck, and shrink our read size
to match. For this purpose, use the algorithm in the DisplayPort 1.2 spec,
in the hopes that it'll be closest to what Windows does.

Also provide an unsafe module parameter for testing smaller transfer sizes,
in case there are sinks out there that cannot work with Windows.

Note also that despite the previous comment in drm_dp_i2c_xfer, this speeds
up native DP EDID reads; Ville Syrjälä <ville.syrjala@linux.intel.com> found
the following changes in his testing:

Device under test:     old  -> with this patch
DP->DVI (OUI 001cf8):  40ms -> 35ms
DP->VGA (OUI 0022b9):  45ms -> 38ms
Zotac DP->2xHDMI:      25ms ->  4ms
Asus PB278 monitor:    22ms ->  3ms

A back of the envelope calculation shows that peak theoretical transfer rate
for 1 byte reads is around 60 kbit/s; with 16 byte reads, this increases to
around 500 kbit/s, which explains the increase in speed.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55228
Tested-by: Aidan Marks <aidanamarks@gmail.com> (v3)
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-03-11 22:04:56 +01:00
Shaohui Xie
19693f1166 net/fsl: remove dependency FSL_SOC from MDIO
FSL_PQ_MDIO and FSL_XGMAC_MDIO are not really depend on FSL_SOC, they
can build on non-PPC platforms.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-11 16:37:50 -04:00
Andy Gross
e5fdad68d4 soc: qcom: gsbi: Add support for ADM CRCI muxing
This patch adds automatic configuration for the ADM CRCI muxing required to
support DMA operations for GSBI clients.  The GSBI mode and instance determine
the correct TCSR ADM CRCI MUX value that must be programmed so that the DMA
works properly.

Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-11 15:18:39 -05:00
Lina Iyer
767b0235dd firmware: qcom: scm: Support cpu power down through SCM
Support powering down the calling cpu, by trapping into SCM. This
termination function triggers the ARM cpu to execute WFI instruction,
causing the power controller to safely power the cpu down.

Caches may be flushed before powering down the cpu. If cache controller
is set to turn off when the cpu is powered down, then the flags argument
indicates to the secure mode to flush its cache lines before executing
WFI.The warm boot reset address for the cpu should be set before the
calling into this function for the cpu to resume.

The original code for the qcom_scm_call_atomic1() comes from a patch by
Stephen Boyd [1]. The function scm_call_atomic1() has been cherry picked
and renamed to match the convention used in this file. Since there are
no users of scm_call_atomic2(), the function is not included.

[1]. https://lkml.org/lkml/2014/8/4/765

Signed-off-by: Stephen Boyd <sboyd@codeauraro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-11 15:15:11 -05:00
Lina Iyer
2ce76a6ad3 firmware: qcom: scm: Add qcom_scm_set_warm_boot_addr function
A core can be powered down for cpuidle or when it is hotplugged off. In
either case, the warmboot return address would be different. Allow
setting the warmboot address for a specific cpu, optimize and write to
the firmware, if the address is different than the previously set
address.

Export qcom_scm_set_warm_boot_addr function move the warm boot flags to
implementation.

Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-11 15:15:07 -05:00
Lina Iyer
a353e4a06f firmware: qcom: scm: Clean cold boot entry to export only the API
We dont need to export the SCM specific cold boot flags to the platform
code. Export only a function to set the cold boot address.

Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-11 15:15:05 -05:00
Arnd Bergmann
369237ab1f Renesas ARM Based SoC r8a7778 CCF and Multiplatform Updates for v4.1
* Add CCF and them multiplatform support to r8a7778 SoC and its
   bockw board.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJU9671AAoJENfPZGlqN0++71UP/iuiuiyeF3Wgqc9Pu22hVg8g
 3qd0Hqw2iUx07KV29kGoJmAkL48A5zGOk/JqvLY2BX5+ZAdWxy4sbY/njMzeUAH6
 hRiZGbgb+7gRSsQNCbxmR6Kh1zx8akxrQOw7PzJs0Yjwh2I8+rrb+2qxDNy1RbO9
 KoTYk4j98mOLdwfGYixoVjSIdgt70JNKUn3LY0JHn6Ss38u/1zDB55PnlXeCKNfu
 t7WSwTxbdN1h0hJ03y3ZsTQMVb3BDYMfRFtWZCZ/AE4CFM53oeRVkXEewbPfPQBn
 b7A05JYKm8NfF8AnbHbgnRJU/3H9kCMylw/rcYGqXGgs2GDL8qxE1O45vsC0ONJj
 rKrwRqvz6d8DrSZmEfufI48ykOPKIsWjJw9TKv/8gXNxu0qF9QjqygEKBt4isOZ7
 DGqy46RZguhJAESZJkMqydpuLBG+QZ4NKXgm0fi9IhDooj/9qZWLpoaoeSZCO9fC
 6ZPGkFA86S9G44bcbrDkp2j86K0lVkoC/Zx/9ZcJMYxauj0/yvDKTH7a/iods7IN
 xvNxKGgl2en2oADsRAHb3+lGSbdpVo0wMzvf5l8qSMElIJKoDs/L0evykeOQEW83
 Kcyd0M3gaX9vSdjrGzrvq6lNXpshGLg/8e+0aAJ9G4x3UKhvc0UnFQ67m1Vmc0Ti
 WG4WMnD3yXFjiNZjDDrd
 =f7JV
 -----END PGP SIGNATURE-----

Merge tag 'renesas-r8a7778-ccf-and-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform

Pull "Renesas ARM Based SoC r8a7778 CCF and Multiplatform Updates
for v4.1" from Simon Horman:

* Add CCF and them multiplatform support to r8a7778 SoC and its
  bockw board.

* tag 'renesas-r8a7778-ccf-and-multiplatform-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (21 commits)
  ARM: shmobile: r8a7778: enable multiplatform target
  ARM: shmobile: bockw: add sound to DT
  ARM: shmobile: r8a7778: add sound to DT
  ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
  DT: i2c: add trivial binding for OKI ML86V7667 video decoder
  ARM: shmobile: r8a7778: common clock framework CPG driver
  ARM: shmobile: bockw dts: set extal clock frequency
  ARM: shmobile: bockw dts: Move Ethernet node to BSC
  ARM: shmobile: r8a7778 dtsi: Add Bus State Controller node
  ARM: shmobile: bockw: add USB, VIN pin descriptions to DT
  ARM: shmobile: r8a7778: add internal ethernet controller to DT
  ARM: shmobile: r8a7778: add MSTP clock assignments to DT
  ARM: shmobile: r8a7778: implement SoC and board CCF support
  ARM: shmobile: r8a7778: Common clock framework DT description
  ARM: shmobile: r8a7778: add CPG register bits header
  ARM: shmobile: r8a7778: synchronize dts with reference platform
  drivers: bus: Add Simple Power-Managed Bus Driver
  drivers: bus: Add Renesas Bus State Controller (BSC) DT Bindings
  drivers: bus: Add Simple Power-Managed Bus DT Bindings
  drivers: bus: Sort Makefile entries alphabetically
  ...
2015-03-11 21:14:55 +01:00
John Youn
9024c495f3 usb: dwc2: pci: Add device mode to the dwc2-pci driver
The pci driver now registers a platform driver, like in dwc3, and lets
its probe function do all the initialization. This allows it to
account for changes to the platform driver that were not added to the
pci driver. Also future changes to the probe function don't have to be
duplicated. This also has the effect of adding device and DRD mode to
the pci driver. Tested on the Synopsys HAPS PCIe platform.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 15:08:17 -05:00
Kumar Gala
916f743da3 firmware: qcom: scm: Move the scm driver to drivers/firmware
Architectural changes in the ARM Linux kernel tree mandate the eventual
removal of the mach-* directories. Move the scm driver to
drivers/firmware and the scm header to include/linux to support that
removal.

Signed-off-by: Kumar Gala <galak@codeaurora.org>
2015-03-11 15:06:38 -05:00
Peter Chen
005a64307d usb: gadget: lpc32xxx_udc: Fix NULL dereference
udc is then checked for NULL, if NULL, it is then dereferenced as
udc->dev, it is found using Coccinelle.

We simplify the code to fix this problem, and we delete some conditions
at if {} which will never be met.

Reported-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Reported-by : Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 14:59:10 -05:00
Julia Lawall
18b44b2b95 EDAC, i82443bxgx: Don't export static symbol
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
type T;
identifier f;
@@

static T f (...) { ... }

@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@

-EXPORT_SYMBOL_GPL(f);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Tim Small <tim@buttersideup.com>
Link: http://lkml.kernel.org/r/1426092997-30605-13-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Borislav Petkov <bp@suse.de>
2015-03-11 20:39:15 +01:00
Thomas Hellstrom
fd3e4d6e26 drm/vmwgfx: Fix an issue with the device losing its irq line on module unload
Starting with commit b4b55cda58
("x86/PCI: Refine the way to release PCI IRQ resources")

the device lost its irq resource on module unload. While that's ok and
apparently intentional, the driver never got the resource back on module load

The code apparently wants drivers to disable the pci device at pci device
driver removal, so lets do that. That fixes the issue.

Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
2015-03-11 11:47:41 -07:00
Colin Ian King
da5efffc42 drm/vmwgfx: Correctly NULLify dma buffer pointer on failure
cppcheck on lines 917 and 977 show an ineffective assignment
to the dma buffer pointer:

[drivers/gpu/drm/vmwgfx/vmwgfx_execbuf.c:917]:
[drivers/gpu/drm/vmwgfx/vmwgfx_execbuf.c:977]:
  (warning) Assignment of function parameter has no effect
  outside the function. Did you forget dereferencing it?

On a successful DMA buffer lookup, the dma buffer pointer is
assigned, however, on failure it currently is left in an
undefined state.

The original intention in the error exit path was to nullify
the pointer on an error (which the original code failed to
do properly). This patch fixes this also ensures all failure
paths nullify the buffer pointer on the error return.

Fortunately the callers to vmw_translate_mob_ptr and
vmw_translate_guest_ptr are checking on a return status and not
on the dma buffer pointer, so the original code worked.

Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
2015-03-11 11:47:41 -07:00
Thomas Hellstrom
3458390b9f drm/vmwgfx: Reorder device takedown somewhat
To take down the MOB and GMR memory types, the driver may have to issue
fence objects and thus make sure that the fence manager is taken down
after those memory types.
Reorder device init accordingly.

Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
2015-03-11 11:47:40 -07:00
Thomas Hellstrom
5151adb37a drm/vmwgfx: Fix a couple of lock dependency violations
Experimental lockdep annotation added to the TTM lock has unveiled a
couple of lock dependency violations in the vmwgfx driver. In both
cases it turns out that the device_private::reservation_sem is not
needed so the offending code is moved out of that lock.

Cc: <stable@vger.kernel.org>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
2015-03-11 11:47:40 -07:00
Jason Gerecke
71fa641ebb HID: wacom: Add battery presence indicator to wireless tablets
Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.

Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 13:50:04 -04:00
Dan Carpenter
b6310affbe Input: sx8654 - signedness bug in sx8654_irq()
"irqsrc" needs to be signed for the error handling to work.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-03-11 10:44:30 -07:00
Charlie Mooney
37dee1acdd Input: elants_i2c - append hw_version to FW file
Currently the elants_i2c driver simply requests a static filename
/lib/firmware/elants_i2c.bin when it gets firmware updates.  This is a
problem if you have two Elan touchscreens using the same driver.  If both
touchscreens have different firmwares, you would need to move the files
around in your filesystem when you're updating them so that they don't get
updated with the other's FW.  If you have a read-only filesystem then this
is impossible, even.

This patch changes the elants_i2c driver to automatically append the
four-hex-digit hw_version of the device onto the name of the FW file it's
requesting for update.  Since different touchscreens should have a
different hw_version's this means the user needs to append the hw version
of the touchscreen he or she intends to update onto the end of the firmware
filename and then the driver will do the rest.

The firmware filenames it looks for now are of the form:

  elants_i2c_${HW_VERSION}.bin

  eg:

  elants_i2c_2a44.bin

Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2015-03-11 10:24:18 -07:00
Boris Brezillon
111573ccd8 mtd: atmel_nand: check NFC busy flag by HSMC_SR instead of NFC cmd regs
Currently the driver read NFC command registers to get NFC busy flag.
Actually this flag also can be get by reading HSMC_SR register.

Use the read NFC command registers need mapping a huge memory region.
To save the mapped memory region, we change to check NFC busy flag by
reading HSMC_SR register.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-03-11 09:49:28 -07:00
Takeyoshi Kikuchi
72a472d2f9 usb: musb: cppi41: fix condition to call cppi41_trans_done().
connect AR9271(USB wifi) to AM335x, and send a flood ping from Mac OSX,
AR9271 is stopped.

on USB bus, the following occurs.

 - OUT transaction is ACKed (NYET).
 - IN transaction is ACKed (512bytes).
 - PING-NAK transaction is continued for about 2 seconds (AR9271 timeout?).

In current imprementation, IN-transaction is not completed because it
checks the empty of TX-FIFO in cppi41_dma_callback().
As a result, communication to AR9271 stops.

This patch modified to check the empty of TX-FIFO only when OUT-transaction.

Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 11:34:37 -05:00
oliver@neukum.org
a415457733 HID: add ALWAYS_POLL quirk for a Logitech 0xc007
This device disconnects every 60s without X

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 12:12:37 -04:00
Jiri Kosina
8fac172214 HID: wacom: drop WACOM_PKGLEN_STATUS
The constant is not used (leftover from previous patch versions
that never got merged).

Reported-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:48:11 -04:00
Jason Gerecke
b0882cb79d HID: wacom: Status packet provides 'charging', not 'powered' bit
The status packet for tablets which can use a wireless module contains a
bit that is set if the battery is charging. This bit will be 0 if either
a battery is not present or if the battery has reached full charge. Note
that the charging circuit may continue to charge the battery for a short
time after reaching "100%".

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:13 -04:00
Jason Gerecke
2d13a43813 HID: wacom: Report battery status for Intuos Pro and Intuos5
Calls the wacom_status_irq function to report battery status for the
Intuos Pro and Intuos5 (in addition to the already-reporting Intuos
and last-generation Bamboo).

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:13 -04:00
Jason Gerecke
8f93b0b2b0 HID: wacom: Provide battery charge state to system over USB if available
If a wireless adapter (which contains the charging circuitry) is
detected as being attached to the tablet then create a new battery
interface and update its status as data is reported. Also destroy the
battery if the adapter goes away.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:12 -04:00
Jason Gerecke
fce9957d8f HID: wacom: Allow dynamic battery creation/destruction
Tablets like the Intuos, Intuos Pro, and Bamboo have a connector for an
optional wireless module that can be connected on the fly. The presence
(or absence) of this module is indicated in a status report recieved
from the tablet. This patch adds a workqueue function that will create
or destroy a power_supply object at runtime to match the current state
of the WACOM_QUIRK_BATTERY flag.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:12 -04:00
Jason Gerecke
953f2c5f71 HID: wacom: Centralize updating of wacom_wac battery status
Has the 'wacom_notify_battery' function take on the job of detecting if
updating the power supply is necessary to remove multiple
nearly-identical 'if' blocks.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:11 -04:00
Jason Gerecke
4ca4ec71c8 HID: wacom: Move handling of Intuos status packets to seperate function
In addition to the touchswitch state for "Intuos", these packets are
also sent by the Intuos Pro, Intuos5, and last-generation Bamboo
tablets when using a wired connection. They contain, among other
things, information about the optional wireless module and battery
charge state (to be supported in subsuquent patches).

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2015-03-11 11:46:11 -04:00
Daniel Vetter
967667fd6d drm/plane-helper: Fixup mismerge
I somehow manage to screw up applying Laurent's patch in eca93e28c256:
"drm: Check in setcrtc if the primary plane supports the fb pixel
format". It was a conflict with

commit 3461b30b3e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Thu Mar 5 10:32:44 2015 +0100

    drm/plane-helper: unexport drm_primary_helper_create_plane

and I just didn't check that the solution from wiggle made sense.

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: laurent.pinchart@ideasonboard.com
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: laurent.pinchart@ideasonboard.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-03-11 16:43:40 +01:00
Peter Hurley
7fd6f640f2 serial: 8250_dw: Fix deadlock in LCR workaround
Trying to write console output from within the serial console driver
while the port->lock is held causes recursive deadlock:

  CPU 0
spin_lock_irqsave(&port->lock)
printk()
  console_unlock()
    call_console_drivers()
      serial8250_console_write()
        spin_lock_irqsave(&port->lock)
** DEADLOCK **

The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.

Make the error message a FIXME until a general solution is devised.

Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-11 16:39:52 +01:00
Jorge Ramirez-Ortiz
48d7ff0eaa drivers/tty: serial: remove info message
Unacceptable levels of debug info will happen when the DMA driver defined in
the DT/ACPI is a blacklisted module.

Another cause for log polution would be the defer probing of the DMA driver
taking too long - in which case the message that this commit removes would be
cluttering the logs due to the init daemons activity.

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-03-11 16:38:25 +01:00
Fabio Estevam
168bdb88c3 usb: phy: phy-generic: No need to call gpiod_direction_output() twice
Commit 9eb0797722 ("usb: phy: generic: fix the gpios to be optional")
calls gpiod_direction_output() in the probe function, so there is no need to
call it again, as we can simply call gpiod_set_value() directly.

Also, in usb_gen_phy_shutdown() we can simply put the GPIO directly in its
active level state and this allows us to simplify the nop_reset function to
treat only the reset case.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 10:19:38 -05:00
Robert Baldyga
f4e4f8dae3 usb: gadget: f_hid: remove unnecessary usb_ep_dequeue()
Function usb_ep_disable() causes completion of all requests queued
for given endpoint, so there is no need to dequeue them after endpoint
disabling.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 10:19:38 -05:00
Rasmus Villemoes
fa84acf0f6 usb: gadget: dummy-hcd: Remove utf8 from format string
Not everybody uses a utf8 locale (unfortunately), so let's avoid
non-ascii characters in the kernel log. Replace the 3-byte utf8
sequence with a 3-byte ascii equivalent.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 10:19:37 -05:00
Sylvain Rochet
112bf24471 usb: gadget: atmel_usba_udc: Add suspend/resume with wakeup support
This patch add suspend/resume with wakeup support for Atmel USBA.

On suspend: We stay continuously clocked if Vbus signal is not
available. If Vbus signal is available we set the Vbus signal as a wake
up source then we stop the USBA itself and all clocks used by USBA.

On resume: We recover clocks and USBA if we stopped them. If a device is
currently connected at resume time we enable the controller.

Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 10:19:37 -05:00
Sylvain Rochet
a64ef71ddc usb: gadget: atmel_usba_udc: condition clocks to vbus state
If USB PLL is not necessary for other USB drivers (e.g. OHCI and EHCI)
we will reduce power consumption by switching off the USB PLL if no USB
Host is currently connected to this USB Device.

We are using Vbus GPIO signal to detect Host presence. If Vbus signal is
not available then the device stays continuously clocked.

Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-03-11 10:19:37 -05:00