if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
PTR_ERR_OR_ZERO simplifies the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Prefer devm_kcalloc over devm_kzalloc with multiply.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
From the comments of gpiod_direction_output(), need to set @value
as initial output, so update the lowlevel routine to make it work.
Signed-off-by: jason.cj.chen<jason.cj.chen@intel.com>
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt is enabled before napi_complete(). A network timeout
occurs if the interrupt handler is called before napi_complete().
Fix the bug by enabling the interrupt after napi_complete().
Signed-off-by: Yongbae Park <yongbae2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7439 has an alternate PHY OUI: 0xae025080 which is to be found in
some variants of this chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the netlink flags (NLM_F_*) into switchdev driver for IPv4 FIB add op
to allow driver to 1) optimize hardware updates, 2) handle ip route prepend
and append commands correctly.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With drm-next, we can get a backtrace from sleeping
with mutex detection.
this is due to the callback checking the txmsg state taking
the mutex, which can cause a sleep inside a sleep,
Daniel went over it and was happy we could drop this mutex
in this case.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This may be OK in archs with contiguous CPU numbers and without
hotplug CPUs, but it sets a terrible example.
And open-coding it like drivers/scsi/hpsa.c is just weird.
BTRFS has a weird comparison with num_online_cpus() too, but since
BTRFS just screwed up my test machines' root partition, I'm not
touching it :)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Oleg Drokin <green@linuxhacker.ru>
1. Add struct bcmgenet_rx_ring to hold all necessary information
for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: Petri Gynther <pgynther@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
"One performance optimization for page_clear and a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix incorrect ASCE after crst_table_downgrade
s390/ftrace: fix crashes when switching tracers / add notrace to cpu_relax()
s390/pci: unify pci_iomap symbol exports
s390/pci: fix [un]map_resources sequence
s390: let the compiler do page clearing
s390/pci: fix possible information leak in mmio syscall
s390/dcss: array index 'i' is used before limits check.
s390/scm_block: fix off by one during cluster reservation
s390/jump label: improve and fix sanity check
s390/jump label: add missing jump_label_apply_nops() call
The internal framebuffers we create to remap legacy cursor ioctls to
plane operations for the universal plane support shouldn't be linke to
the file like normal userspace framebuffers. This bug goes back to the
original universal cursor plane support introduced in
commit 161d0dc1dc
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Jun 10 08:28:10 2014 -0700
drm: Support legacy cursor ioctls via universal planes when possible (v4)
The isn't too disastrous since fbs are small, we only create one when the
cursor bo gets changed and ultimately they'll be reaped when the window
server restarts.
Conceptually we'd want to just pass NULL for file_priv when creating it,
but the driver needs the file to lookup the underlying buffer object for
cursor id. Instead let's move the file_priv linking out of
add_framebuffer_internal() into the addfb ioctl implementation, which is
the only place it is needed. And also rename the function for a more
accurate since it only creates the fb, but doesn't add it anywhere.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> (fix & commit msg)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (provider of lipstick)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
virtio balloon has this code:
wait_event_interruptible(vb->config_change,
(diff = towards_target(vb)) != 0
|| vb->need_stats_update
|| kthread_should_stop()
|| freezing(current));
Which is a problem because towards_target() call might block after
wait_event_interruptible sets task state to TAST_INTERRUPTIBLE, causing
the task_struct::state collision typical of nesting of sleeping
primitives
See also http://lwn.net/Articles/628628/ or Thomas's
bug report
http://article.gmane.org/gmane.linux.kernel.virtualization/24846
for a fuller explanation.
To fix, rewrite using wait_woken.
Cc: stable@vger.kernel.org
Reported-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires that all drivers set DRIVER_OK
before using devices. While balloon isn't yet
included in the virtio 1 spec, previous spec versions
also required this.
virtio balloon might violate this rule: probe calls
kthread_run before setting DRIVER_OK, which might run
immediately and cause balloon to inflate/deflate.
To fix, call virtio_device_ready before running the kthread.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Pull networking fixes from David Miller:
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
A couple of driver specific fixes plus a fix for a regression in the
core where the updates to use sysfs group registration were overly
enthusiastic in eliding properties and removed some that had been
previously present.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU+t5DAAoJECTWi3JdVIfQUmAH/RWw593bjWRnenayjTRF/RYJ
QLayzR/jwPJ7S+occVCpLbUGi4hlDFHePDqbSYQ5VHoqoXxluOW7YH/vSX3gTIj+
46CQOhph223UvwKHj/6KDhCcEynnJCMZIKCnM4friUxXr1tcBAhcEVGR86lWl3ef
xjpUdh4Txf/b3muHayL3aQd0sUTRV7uFlNEn33MgiUmzty3uqx3aSiify2Cj0aCc
TAhEBR8+0BGHOkj0P5/XGzSbdsASi37gbHgXFZ2gekaG/unuZnLQsHaCA81uch4/
6dwU/NjH934NKGEqUcuOCi4lrFHND2vNPWB4q5l2jw+5BUZPpdgW1wXjvyG3+pc=
=+dnv
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of driver specific fixes plus a fix for a regression in the
core where the updates to use sysfs group registration were overly
enthusiastic in eliding properties and removed some that had been
previously present"
* tag 'regulator-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix regression due to NULL constraints check
regulator: rk808: Set the enable time for LDOs
regulator: da9210: Mask all interrupt sources to deassert interrupt line
A collection of driver specific fixes to which the usual comments about
them being important if you see them mostly apply (except for the
comment fix). The pl022 one is particularly nasty for anyone affected
by it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU+tr0AAoJECTWi3JdVIfQ4HIH/2p3AR8VJ1NzmqKslFUaC7SQ
CT6iIiV+1gT+Q/2CLtTwY04gVJrmbO85pl4aotefxuCsb8YFGPCEo3f0lYU/3XwK
ZQuC/7LFpWCqQCtSxoat9XQBHoFkWMrFDdsesQJLg9F46bCx/vVUuMaPrTXwSPLG
DA6isoNZgEBJeKAxKhOdwT/nJUrVJhNwEX8fa/vuISnde4ckVuX+34O60V0N0/S2
7hEw3LQFZW0IPsnkmEygd5ATonK/+s7BXLwoAZWJGpZeWB1YsBUiHV7fLunj6gVy
DMbKI3Fp1Yy/q0h6J+DzzbLvQxj0WTAX8EUz8PCh2QYRvUNiKeJdbKLbLUjGZgA=
=Lpqm
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes to which the usual comments
about them being important if you see them mostly apply (except for
the comment fix). The pl022 one is particularly nasty for anyone
affected by it"
* tag 'spi-v4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: pl022: Fix race in giveback() leading to driver lock-up
spi: dw-mid: avoid potential NULL dereference
spi: img-spfi: Verify max spfi transfer length
spi: fix a typo in comment.
spi: atmel: Fix interrupt setup for PDC transfers
spi: dw: revisit FIFO size detection again
spi: dw-pci: correct number of chip selects
drivers: spi: ti-qspi: wait for busy bit clear before data write/read
Pull tpm fixes from James Morris:
"fixes for the TPM driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix call order in tpm-chip.c
tpm/ibmvtpm: Additional LE support for tpm_ibmvtpm_send
* Fix regression in with omapdss when using i2c displays
* Fix possible null deref in fbmon
* Check kalloc return value in AMBA CLCD
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GHOG
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- Fix regression in with omapdss when using i2c displays
- Fix possible null deref in fbmon
- Check kalloc return value in AMBA CLCD
* tag 'fbdev-fixes-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
OMAPDSS: fix regression with display sysfs files
video: fbdev: fix possible null dereference
video: ARM CLCD: Add missing error check for devm_kzalloc
Pull libata fixlet from Tejun Heo:
"Speed limiting fix for sata_fsl"
* 'for-4.0-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata-fsl: Apply link speed limits
Synchronized flash strobe feature has been considered not fitting
for LED subsystem sysfs interface and thus is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
While registering serio device for i8042, mark them as wakeup-capable
and check their user space wakeup settings in i8042_pm_suspend() and
i8042_pm_resume() to enable or disable, respectively, their interrupts
to wake up the system.
This makes it possible to use the PC keyboard to wake up the system
from suspend-to-idle, among other things, after writing "enabled" to
the keyboard serio device's power/wakeup sysfs attribute.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The count field is an unsigned 32bit value, and the
counter_show() function should also treat it as a unsigned
value.
Otherwise the counter may show negative number as we found on a
machine:
...
gpe23: 0 invalid
gpe24: -2071733 enabled
gpe25: 0 invalid
...
gpe_all: -2070980
sci: -2070949
Signed-off-by: Nan Li <nli@suse.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enhances debugging with the GPE reference count messages added.
This kind of log entries can be used by the platform validators to validate
if there is an EC transaction broken because of firmware/driver bugs.
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch refines logging/debugging splitter support so that when DEBUG is
disabled, splitters won't be visible in the kernel logs while they are
still available for developers when DEBUG is enabled.
This patch also refines the splitters to mark the following handling
process boundaries:
+++++: boundary of driver starting/stopping
boundary of IRQ storming
=====: boundary of transaction advancement
*****: boundary of EC command
boundary of EC query
#####: boundary of EC _Qxx evaluation
The following 2 log entries are originally logged using pr_info() in order
to be used as the boot/suspend/resume log entries for the EC device, this
patch also restores them to pr_info() logging level:
ACPI : EC: EC started
ACPI : EC: EC stopped
In this patch, one log entry around "Polling quirk" is converted into
ec_dbg_raw() which doesn't contain the boundary marker.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 7d78cbefaa (serial: 8250_dw: add ability to handle
the peripheral clock) introduces handling for a second clk
to 8250_dw.c which is the driver also for LPSS UART. The
second clk forces us to provide identifier (con_id) for the
clkdev we create.
This fixes an issue where 8250_dw.c is getting the same
handler for both clocks.
Fixes: 7d78cbefaa (serial: 8250_dw: add ability to handle the peripheral clock)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
commit a8c6ecb3be
Merge: 8dd0eb359eccca0
Author: Dave Airlie <airlied@redhat.com>
Date: Mon Mar 9 19:58:30 2015 +1000
Merge tag 'v4.0-rc3' into drm-next
managed to pick the wrong code to resolve the conflict and left us with
a mutex_lock(struct_mutex) without the mutex_unlock(struct_mutex) leading
to a deadlock. Fix the problem by recovering the correct code which doesn't
need the lock.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similar to the reasoning for the previous commit
DIV_ROUND_CLOSEST(parent_rate, rate)
might not be the best integer divisor to get a good approximation for
rate from parent_rate (given the metric for CLK_DIVIDER_ROUND_CLOSEST).
For example assume a parent rate of 1000 Hz and a target rate of 700.
Using DIV_ROUND_CLOSEST the suggested divisor gets calculated to 1
resulting in a target rate of 1000 with a delta of 300 to the desired
rate. With choosing 2 as divisor however the resulting rate is 500 which
is nearer to 700.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbe (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbe (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
(cooloney@gmail.com: add _unregister function into the document)
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-03-09
This series contains updates to i40e and i40evf.
Greg cleans up some "hello world" strings which were left around from
early development.
Shannon modifies the drive to make sure the sizeof() calls are taking
the size of the actual struct that we care about. Also updates the
NVMUpdate read/write so that it is less noisy when logging. This was
because the NVMUpdate tool does not necessarily know the ReadOnly map of
the current NVM image, and must try reading and writing words that may be
protected. This generates an error out of the Firmware request that the
driver logs. Unfortunately, this ended up spitting out hundreds of
bogus read/write error messages. If a user wants the noisy logging,
the change can be overridden by enabling the NVM update debugging.
Mitch fixes a possible deadlock issue where if a reset occurred when the
netdev is closed, the reset task will hang in napi_disable. Added
ethtool RSS support as suggested by Ben Hutchings.
Jesse fixes a bug introduced in the force writeback code, where the
interrupt rate was set to 0 (maximum) by accident. The driver must
correctly set the NOITR fields to avoid IT update as a side effect
of triggering the software interrupt.
I provided a simple cleanup to make the use of PF/VF consistent, which
was reported by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of clearing the RxU, RxO, and TxO IRQs individually with
3 register reads, a single read of the ICR register will do the
same thing.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_set_optimum_mode() is changing name to
regulator_set_load(), so update the code accordingly.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_set_optimum_mode() is changing name to
regulator_set_load(), so update the code accordingly.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_set_optimum_mode() is changing name to
regulator_set_load(), so update the code accordingly. Also cleaned up
ufshcd_config_vreg_load() while touching the code.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the regulator_set_optimum_mode() function regulator_set_load() to
better represent what's going on.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
intel_mid_dma seems to be unmaintained for a long time. Moreover, the IP block
of DMA itself is the same in both dw_dmac and intel_mid_dma. This patch moves
spi-dw-midpci to use dw_dmac driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core has a comprehensive function set to map and unmap a message when it's
needed. This patch converts driver to use that advantage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch shuts up any ongoing DMA transfer in case of error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In according to documentation SPI in DMA mode may encounter underrun/overrun
failures in rare cases. When such failure occurs, an error recovery protocol is
expected to be implemented in the device driver so that the failed transaction
can be restarted.
This patch enables FIFO overrun / underrun interrupts in DMA case and adds a
handler for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>