When doing memcpy/memset of EQEs, we should use sizeof struct
mlx4_eqe as the base size and not caps.eqe_size which could be bigger.
If caps.eqe_size is bigger than the struct mlx4_eqe then we corrupt
data in the master context.
When using a 64 byte stride, the memcpy copied over 63 bytes to the
slave_eq structure. This resulted in copying over the entire eqe of
interest, including its ownership bit -- and also 31 bytes of garbage
into the next WQE in the slave EQ -- which did NOT include the ownership
bit (and therefore had no impact).
However, once the stride is increased to 128, we are overwriting the
ownership bits of *three* eqes in the slave_eq struct. This results
in an incorrect ownership bit for those eqes, which causes the eq to
seem to be full. The issue therefore surfaced only once 128-byte EQEs
started being used in SRIOV and (overarchitectures that have 128/256
byte cache-lines such as PPC) - e.g after commit 77507aa249
"net/mlx4_core: Enable CQE/EQE stride support".
Fixes: 08ff32352d ('mlx4: 64-byte CQE/EQE support')
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not set the ins_vlan field to zero when no vlan id is present in the packet.
Since WQEs in the TX ring are not zeroed out between uses, this oversight
could result in having vlan flags present in the WQE ctrl segment when no
vlan is preset.
Fixes: e38af4faf0 ('net/mlx4_en: Add support for hardware accelerated 802.1ad vlan')
Reported-by: Gideon Naim <gideonn@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2751c9882b ("vhost: cross-endian
support for legacy devices") introduced a minor regression: even with
cross-endian disabled, and even on LE host, vhost_is_little_endian is
checking is_le flag so there's always a branch.
To fix, simply check virtio_legacy_is_little_endian first.
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delete action of ETHTOOL_ID_ON/ETHTOOL_ID_OFF in XGE ethtool -p,
so Hardware control the LED state instead of software.
Signed-off-by: Li Peng <lipeng321@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increased TX_TIMEOUT to 5HZ to accommodate worst case situation
for traffic and CPU intensive use cases
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Abhimanyu <abhimanyu@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM cpuidle changes for v4.4 from Daniel Lezcano.
* 'cpuidle/4.4' of http://git.linaro.org/people/daniel.lezcano/linux:
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWLzQ5AAoJEG4XJFUm622btRwH/A6fS7p5uSZzH5lIU8ZBLc7X
MzC1jYVepHXaR5+OhBIbQ5oSo47Y4xqMeO2ylFMpUSg4vntqR9yZNVH2lXV5EfPB
fIaGYIsb3ExjAFoIjFUBwqSOB7CCZK5myk+SLiOu9XghjsLObP5JLKgA49PGhFRn
CCuDq9diDNeJBnVzTS1ms5wO6RmOBiizzjbu7adJI0Hu63z2+P4pNMG4Zz6E1z97
z8DRFEwdNN9gKHIaEC61h7ZT9XDB/Tj31Wl3Irbi4GBS7sRXnFK46FYU8fMVDbDZ
ykj05sq6nTrfwfVZtXbV3SxlYNSN4SFFRuskon6IUcIzlNTuIULgvlpCjJJ6tyQ=
=pFoQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During Tx cleanup it's still possible for the descriptor data to be
read ahead of the descriptor index. A memory barrier is required between
the read of the descriptor index and the start of the Tx cleanup loop.
This allows a change to a lighter-weight barrier in the Tx transmit
routine just before updating the current descriptor index.
Since the memory barrier does result in extra overhead on arm64, keep
the previous change to not chase the current descriptor value. This
prevents the execution of the barrier for each loop performed.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forcedeth currently uses disable_irq_lockdep and enable_irq_lockdep, which in
some configurations simply calls local_irq_disable. This causes errant warnings
in the netpoll path as in netpoll_send_skb_on_dev, where we disable irqs using
local_irq_save, leading to the following warning:
WARNING: at net/core/netpoll.c:352 netpoll_send_skb_on_dev+0x243/0x250() (Not
tainted)
Hardware name:
netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll
(nv_start_xmit_optimized+0x0/0x860 [forcedeth])
Modules linked in: netconsole(+) configfs ipv6 iptable_filter ip_tables ppdev
parport_pc parport sg microcode serio_raw edac_core edac_mce_amd k8temp
snd_hda_codec_realtek snd_hda_codec_generic forcedeth snd_hda_intel
snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd soundcore
snd_page_alloc i2c_nforce2 i2c_core shpchp ext4 jbd2 mbcache sr_mod cdrom sd_mod
crc_t10dif pata_amd ata_generic pata_acpi sata_nv dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 1940, comm: modprobe Not tainted 2.6.32-573.7.1.el6.x86_64.debug #1
Call Trace:
[<ffffffff8107bbc1>] ? warn_slowpath_common+0x91/0xe0
[<ffffffff8107bcc6>] ? warn_slowpath_fmt+0x46/0x60
[<ffffffffa00fe5b0>] ? nv_start_xmit_optimized+0x0/0x860 [forcedeth]
[<ffffffff814b3593>] ? netpoll_send_skb_on_dev+0x243/0x250
[<ffffffff814b37c9>] ? netpoll_send_udp+0x229/0x270
[<ffffffffa02e3299>] ? write_msg+0x39/0x110 [netconsole]
[<ffffffffa02e331b>] ? write_msg+0xbb/0x110 [netconsole]
[<ffffffff8107bd55>] ? __call_console_drivers+0x75/0x90
[<ffffffff8107bdba>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107c445>] ? release_console_sem+0xe5/0x250
[<ffffffff8107d200>] ? register_console+0x190/0x3e0
[<ffffffffa02e71a6>] ? init_netconsole+0x1a6/0x216 [netconsole]
[<ffffffffa02e7000>] ? init_netconsole+0x0/0x216 [netconsole]
[<ffffffff810020d0>] ? do_one_initcall+0xc0/0x280
[<ffffffff810d4933>] ? sys_init_module+0xe3/0x260
[<ffffffff8100b0d2>] ? system_call_fastpath+0x16/0x1b
---[ end trace f349c7af88e6a6d5 ]---
console [netcon0] enabled
netconsole: network logging started
Fix it by modifying the forcedeth code to use
disable_irq_nosync_lockdep_irqsavedisable_irq_nosync_lockdep_irqsave instead,
which saves and restores irq state properly. This also saves us a little code
in the process
Tested by the reporter, with successful restuls
Patch applies to the head of the net tree
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the overhead of locking for busy poll.
Previously the state was protected by a lock, whereas now
it's manipulated solely with atomic operations.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debugging input devices, specifically laptop touchpads, can be tricky
without having the physical device handy. Here we try to remedy that
with userio. This module allows an application to connect to a character
device provided by the kernel, and emulate any serio device. In
combination with userspace programs that can record PS/2 devices and
replay them through the /dev/userio device, this allows developers to
debug driver issues on the PS/2 level with devices simply by requesting
a recording from the user experiencing the issue without having to have
the physical hardware in front of them.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI controllers may need to be properly setup before chip selects
can be used. Therefore, wait until the spi controller has a chance
to perform their setup procedure before trying to use the chip
select.
This also insures that the chip selects pins are in a good
state before asseting them which otherwise may cause confusion.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset 0x60 is the offset of the data register defined as DW_SPI_DR in the
header file. Use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a major overhaul of the clk-qoriq driver, which I'm merging
via PPC with Stephen Boyd's ack in order to apply subsequent PPC patches
that depend on it.
Pull ARM fixes from Russell King:
"Two fixes for ARM and one for clkdev:
- Fix another build issue with vdsomunge on non-glibc systems
- Fix a randconfig build error caused by an invalid configuration
- Fix a clkdev problem causing the Nokia n700 to no longer boot"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
clkdev: fix clk_add_alias() with a NULL alias device name
ARM: 8445/1: fix vdsomunge not to depend on glibc specific byteswap.h
ARM: make RiscPC depend on MMU
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
In order to only build dtbs, this option can be used by creating an
allno.config file containing:
CONFIG_COMPILE_TEST=y
CONFIG_OF=y
CONFIG_OF_ALL_DTBS=y
And then running:
make KCONFIG_ALLCONFIG=1 allnoconfig
make dtbs
While building the dtbs themselves don't need a cross compiler, the
scripts dependency does need one. This can be hacked around by
commenting out "subdir-y += mod" in scripts/Makefile.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
The vfio platform driver currently sets the IRQ_NOAUTOEN before
doing the request_irq to properly handle the user masking. However
it does not clear it when de-assigning the IRQ. This brings issues
when loading the native driver again which may not explicitly enable
the IRQ. This problem was observed with xgbe driver.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The PCI VPD capability operates on a set of window registers in PCI
config space. Writing to the address register triggers either a read
or write, depending on the setting of the PCI_VPD_ADDR_F bit within
the address register. The data register provides either the source
for writes or the target for reads.
This model is susceptible to being broken by concurrent access, for
which the kernel has adopted a set of access functions to serialize
these registers. Additionally, commits like 932c435cab ("PCI: Add
dev_flags bit to access VPD through function 0") and 7aa6ca4d39
("PCI: Add VPD function 0 quirk for Intel Ethernet devices") indicate
that VPD registers can be shared between functions on multifunction
devices creating dependencies between otherwise independent devices.
Fortunately it's quite easy to emulate the VPD registers, simply
storing copies of the address and data registers in memory and
triggering a VPD read or write on writes to the address register.
This allows vfio users to avoid seeing spurious register changes from
accesses on other devices and enables the use of shared quirks in the
host kernel. We can theoretically still race with access through
sysfs, but the window of opportunity is much smaller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
When determining whether a group is viable, we already allow devices
bound to pcieport. Generalize this to include any PCI bridge device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
fdt_translate_address() returns OF_BAD_ADDR on error. It is defined as
a u64 value, so the variable "addr" should be defined as u64 as well.
Fixes: fb11ffe74c ("of/fdt: add FDT serial scanning for earlycon")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The halt bits for these clocks seem wrong. I get the following
warning while booting on an msm8960-cdp:
WARNING: CPU: 0 PID: 1 at drivers/clk/qcom/clk-branch.c:97 clk_branch_toggle+0xd0/0x138()
dsi1_clk status stuck at 'on'
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.0-rc3-00113-g5532cfb567fe #110
Hardware name: Qualcomm (Flattened Device Tree)
[<c0216984>] (unwind_backtrace) from [<c02138f8>] (show_stack+0x10/0x14)
[<c02138f8>] (show_stack) from [<c04a525c>] (dump_stack+0x70/0xbc)
[<c04a525c>] (dump_stack) from [<c0223c70>] (warn_slowpath_common+0x78/0xb4)
[<c0223c70>] (warn_slowpath_common) from [<c0223d40>] (warn_slowpath_fmt+0x30/0x40)
[<c0223d40>] (warn_slowpath_fmt) from [<c05fc2dc>] (clk_branch_toggle+0xd0/0x138)
[<c05fc2dc>] (clk_branch_toggle) from [<c05f3f3c>] (clk_disable_unused_subtree+0x98/0x1b0)
[<c05f3f3c>] (clk_disable_unused_subtree) from [<c05f3ec4>] (clk_disable_unused_subtree+0x20/0x1b0)
[<c05f3ec4>] (clk_disable_unused_subtree) from [<c05f5474>] (clk_disable_unused+0x58/0xd8)
[<c05f5474>] (clk_disable_unused) from [<c0209710>] (do_one_initcall+0xac/0x1ec)
[<c0209710>] (do_one_initcall) from [<c0991db4>] (kernel_init_freeable+0x11c/0x1e8)
[<c0991db4>] (kernel_init_freeable) from [<c0727ae0>] (kernel_init+0x8/0xec)
[<c0727ae0>] (kernel_init) from [<c0210238>] (ret_from_fork+0x14/0x3c)
Fix the status bits and the errors go away.
Fixes: 5532cfb567 ("clk: qcom: mmcc-8960: Add DSI related clocks")
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The description of the XUSB_PADCTL_USB3_PAD_MUX_0 register in the Tegra124
documentation implies that all functions (pcie, usb3 and sata) can be
muxed onto to all lanes (pcie lanes 0-4 and sata lane 0). However, it has
been confirmed that this is not the case and the mux'ing options much more
limited. Unfortunately, the public documentation has not been updated to
reflect this and so detail the actual mux'ing options here by function:
Function: Lanes:
pcie1 x2: pcie3, pcie4
pcie1 x4: pcie1, pcie2, pcie3, pcie4
pcie2 x1 (option1): pcie0
pcie2 x1 (option2): pcie2
usb3 port 0: pcie0
usb3 port 1 (option 1): pcie1
usb3 port 1 (option 2): sata0
sata: sata0
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to leave space for the NUL char.
Fixes: 8ea4484d0c ('mailbox: Add generic mechanism for testing Mailbox Controllers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Currently there is no way to easily differentiate multiple
watchdog devices. The watchdogs are named by the order they
are probed.
1st probed watchdog: /dev/watchdog0
2nd probed watchdog: /dev/watchdog1
...
This change uses the alias of the watchdog device node for
the name of the watchdog.
aliases {
watchdog0 = "/...../...."
watchdog3 = "/..../....."
watchdog2 = "/..../....."
...
}
This will translate to...
/dev/watchdog0
/dev/watchdog3
/dev/watchdog2
v2
Assign alias number to id in watchdog_core instead of watchdog_dev.
If failed to get id, fallback to original ida_simple_get call.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The driver does not have any real architecture dependencies. To avoid
listing each architecture that might use this driver on some
FPGA-enabled platform, drop these dependencies.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A typo resulted in the watermarks for cursor planes not being calculated
correctly. Fixed the typo.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This driver adds pinctrl/GPIO support for Intel Broxton. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reserved for ACPI actually means that in such case the GPIO hardware will
not update the interrupt status register (GPI_IS) even if the pin is
configured to trigger an interrupt. It will update GPI_GPE_STS instead and
does not trigger an interrupt.
Allow using such pins as GPIOs, only prevent their usage as interrupts.
We also rename function intel_pad_reserved_for_acpi() to be
intel_pad_acpi_mode() which reflects the actual meaning better.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Intel Broxton the GPIO hardware consists of several chips that all share
the parent interrupt. It is not possible to handle this by setting chained
handler for each chip (as they will overwrite each other).
To overcome this we need to request the interrupt using devm_request_irq()
and pass IRQF_SHARED with the flags.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Returning an error instead of NULL in bgpio_map if
platform_get_resource_byname does not find a resource was introduced with
commit cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map").
This results in several qemu runtime failures with default and non-default
configurations, if attempts are made to boot from mmcblk0. Examples for
failures with multi_v7_defconfig are
Machine: vexpress-a9 dtb: vexpress-v2p-ca9
Machine: vexpress-a15 dtb: vexpress-v2p-ca15-tc1
Crash:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Looking into the code, always returning an error if bgpio_map fails
does not appear to make much sense, since the code in bgpio_setup_io
specifically supports some of the resources to be NULL.
Fixes: cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For pinctrl the "default" state is applied to pins before the driver's
probe function is called. This is normally a sensible thing to do,
but in some cases can cause problems. That's because the pins will
change state before the driver is given a chance to program how those
pins should behave.
As an example you might have a regulator that is controlled by a PWM
(output high = high voltage, output low = low voltage). The firmware
might leave this pin as driven high. If we allow the driver core to
reconfigure this pin as a PWM pin before the PWM's probe function runs
then you might end up running at too low of a voltage while we probe.
Let's introudce a new "init" state. If this is defined we'll set
pinctrl to this state before probe and then "default" after probe
(unless the driver explicitly changed states already).
An alternative idea that was thought of was to use the pre-existing
"sleep" or "idle" states and add a boolean property that we should
start in that mode. This was not done because the "init" state is
needed for correctness and those other states are only present (and
only transitioned in to and out of) when (optional) power management
is enabled.
Changes in v3:
- Moved declarations to pinctrl/devinfo.h
- Fixed author/SoB
Changes in v2:
- Added comment to pinctrl_init_done() as per Linus W.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pwrseq_emmc driver does a eMMC card reset before a system reboot to
allow broken or limited ROM boot-loaders (that don't have an eMMC reset
logic) to be able to read the second stage from the eMMC.
But this has to be called before a system reboot handler and while most
of them use the priority 128, there are other restart handlers (such as
the syscon-reboot one) that use a higher priority. So, use the highest
priority to make sure that the eMMC hw is reset before a system reboot.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While IECTRL is disabled, input signals are pulled-down internally.
If pin-muxing is set up first, glitch signals (Low to High transition)
might be input to hardware blocks.
Bad case scenario:
[1] The hardware block is already running before pinctrl is handled.
(the reset is de-asserted by default or by a firmware, for example)
[2] The pin-muxing is set up. The input signals to hardware block
are pulled-down by the chip-internal biasing.
[3] The pins are input-enabled. The signals from the board reach the
hardware block.
Actually, one invalid character is input to the UART blocks for such
SoCs as PH1-LD4, PH1-sLD8, where UART devices start to run at the
power on reset.
To avoid such problems, pins should be input-enabled before muxing.
Fixes: 6e90889202 ("pinctrl: UniPhier: add UniPhier pinctrl core support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpio to pinctrl pin mapping code from driver and
address this through standard property "gpio-ranges".
Signed-off-by: Pramod Kumar <pramodku@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
