This patch adds four new fields to directory leaf blocks.
The intent is not to use them in the kernel itself, although
perhaps we may be able to use them as hints at some later date,
but instead to provide more information for debug/fsck use.
One new field adds a pointer to the inode to which the leaf
belongs. This can be useful if the pointer to the leaf block
has become corrupt, as it will allow us to know which inode
this block should be associated with. This field is set when
the leaf is created and never changed over its lifetime.
The second field is a "distance from the hash table" field.
The meaning is as follows:
0 = An old leaf in which this value has not been set
1 = This leaf is pointed to directly from the hash table
2+ = This leaf is part of a chain, pointed to by another leaf
block, the value gives the position in the chain.
The third and fourth fields combine to give a time stamp of
the most recent directory insertion or deletion from this
leaf block. The time stamp is not updated when a new leaf
block is chained from the current one. The code is currently
written such that the timestamp on the dir inode will match
that of the leaf block for the most recent insertion/deletion.
For backwards compatibility, any of these new fields which is
zero should be considered to be "unknown".
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide a quick way to tell if a DAI is a dummy DAI or a regular DAI.
This is for internal DAPM usage only and is used to determine whether to
insert a DAI link connection into the DAPM graph.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If the regcache is enabled on the regmap module drivers might need to access
to HW register(s) in certain cases in cache bypass mode.
As an example of this is the audio block's ANAMICL register. In normal
operation the content can be cached but during initialization one bit from
the register need to be monitored. With the twl_set_regcache_bypass() the
client driver can switch regcache bypass on and off when it is needed so
we can utilize the regcache for more registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When a client looks up a ttm object, don't look it up through the device hash
table, but rather from the file hash table. That makes sure that the client
has indeed put a reference on the object, or in gem terms, has opened
the object; either using prime or using the global "name".
To avoid a performance loss, make sure the file hash table entries can be
looked up from under an RCU lock, and as a consequence, replace the rwlock
with a spinlock, since we never need to take it in read mode only anymore.
Finally add a ttm object lookup function for the device hash table, that is
intended to be used when we put a ref object on a base object or, in gem terms,
when we open the object.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Needed for some vm operations; most notably unmap_mapping_range() with
even_cows = 0.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
On overflow, the math-emu macro _FP_TO_INT_ROUND tries to saturate its
result (subject to the value of rsigned specifying the desired
overflow semantics). However, if the rounding step has the effect of
increasing the exponent so as to cause overflow (if the rounded result
is 1 larger than the largest positive value with the given number of
bits, allowing for signedness), the overflow does not get detected,
meaning that for unsigned results 0 is produced instead of the maximum
unsigned integer with the give number of bits, without an exception
being raised for overflow, and that for signed results the minimum
(negative) value is produced instead of the maximum (positive) value,
again without an exception. This patch makes the code check for
rounding increasing the exponent and adjusts the exponent value as
needed for the overflow check.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The math-emu macros _FP_TO_INT and _FP_TO_INT_ROUND are supposed to
saturate their results for out-of-range arguments, except in the case
rsigned == 2 (when instead the low bits of the result are taken).
However, in the case rsigned == 0 (converting to unsigned integers),
they mistakenly produce 0 for positive results and the maximum
unsigned integer for negative results, the opposite of correct
unsigned saturation. This patch fixes the logic.
Signed-off-by: Joseph Myers <joseph@codesourcery.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
We should const-ify comparisons on skb_queue_* inline helper
functions as their parameters are const as well, so lets not
drop that.
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating space for 32-bit BARs, we previously limited RESOURCE
addresses so they would fit in 32 bits. However, the BUS address need not
be the same as the resource address, and it's the bus address that must fit
in the 32-bit BAR.
This patch adds:
- pci_clip_resource_to_region(), which clips a resource so it contains
only the range that maps to the specified bus address region, e.g., to
clip a resource to 32-bit bus addresses, and
- pci_bus_alloc_from_region(), which allocates space for a resource from
the specified bus address region,
and changes pci_bus_alloc_resource() to allocate space for 64-bit BARs from
the entire bus address region, and space for 32-bit BARs from only the bus
address region below 4GB.
If we had this window:
pci_root HWP0002:0a: host bridge window [mem 0xf0180000000-0xf01fedfffff] (bus address [0x80000000-0xfedfffff])
we previously could not put a 32-bit BAR there, because the CPU addresses
don't fit in 32 bits. This patch fixes this, so we can use this space for
32-bit BARs.
It's also possible (though unlikely) to have resources with 32-bit CPU
addresses but bus addresses above 4GB. In this case the previous code
would allocate space that a 32-bit BAR could not map.
Remove PCIBIOS_MAX_MEM_32, which is no longer used.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1386658484-15774-3-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For L3-proto independant rules we need to get at the L4 protocol value
directly. Add it to the nft_pktinfo struct and use the meta expression
to retrieve it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Needed by multi-family tables to distinguish IPv4 and IPv6 packets.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new table family and a new filter chain that you can
use to attach IPv4 and IPv6 rules. This should help to simplify
rule-set maintainance in dual-stack setups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support to register chains to multiple hooks for different address
families for mixed IPv4/IPv6 tables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Multi-family tables need the AF from the hook ops. Add a pointer to the
hook ops and replace usage of the hooknum member in struct nft_pktinfo.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This value is no longer used by mac80211, and practically no
driver ever set it to a correct value anyway, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we have one to three pinctrl-single instances for each SoC it is
a bit confusing to configure the padconf register offset from the
base of the padconf register base.
Let's add macros that allow using the physical address of the
padconf register directly, or in most cases, just the last 16-bits
of the address as they are shown in the documentation.
Note that most documentation shows two padconf registers for each
32-bit address, so adding 2 to the documentation address is needed for
the second padconf register as we treat them as 16-bit registers
for omap3+.
For example, omap36xx documentation shows sdmmc2_clk at 0x48002158,
so we can just use the last 16-bits of that value:
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
And we don't need to separately calculate the offset from the 0x2030
base:
pinctrl-single,pins = <
0x128 (PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
Naturally both ways of defining the registers can be used, and I'm
not saying we should replace all the existing defines. But it may
be handy to use these macros for new entries and when doing other
related .dts file clean-up.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 range]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows to follow a recommandation of RFC4942.
- Add "anycast_src_echo_reply" sysctl to control the use of anycast addresses
as source addresses for ICMPv6 echo reply. This sysctl is false by default
to preserve existing behavior.
- Add inline check ipv6_anycast_destination().
- Use them in icmpv6_echo_reply().
Reference:
RFC4942 - IPv6 Transition/Coexistence Security Considerations
(http://tools.ietf.org/html/rfc4942#section-2.1.6)
2.1.6. Anycast Traffic Identification and Security
[...]
To avoid exposing knowledge about the internal structure of the
network, it is recommended that anycast servers now take advantage of
the ability to return responses with the anycast address as the
source address if possible.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some BE DAIs can be "dummy" (when the DSP is controlling the DAI) and as such
wont have set a minimum number of playback or capture channels required for BE
DAI registration (to establish supported stream directions).
Force machine drivers to explicitly set whether they support playback and capture
stream directions for every BE DAIs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
this gives ability to convey the valid values of supported rates in
sample_rates array
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently Intel interrupt remapping drivers uses the "present" flag bit
in remapping entry to track whether an entry is allocated or not.
It works as follow:
1) allocate a remapping entry and set its "present" flag bit to 1
2) compose other fields for the entry
3) update the remapping entry with the composed value
The remapping hardware may access the entry between step 1 and step 3,
which then observers an entry with the "present" flag set but random
values in all other fields.
This patch introduces a dedicated bitmap to track remapping entry
allocation status instead of sharing the "present" flag with hardware,
thus eliminate the race window. It also simplifies the implementation.
Tested-and-reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
domain_has_cap is a misnomer bc the func name should be
the same for CONFIG_IOMMU_API and !CONFIG_IOMMU_API.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Some embedded systems use hibernation for fast boot. and in it,
some software components need to handle specific things before
hibernation and after restore. So it needs to capture the apm
status about these pm events.
Currently apm just supports suspend to ram, but not suspend to disk,
so here add logic about hibernation apm events.
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If start_streaming returns -ENOBUFS, then it will be retried the next time
a buffer is queued. This means applications no longer need to know how many
buffers need to be queued before STREAMON can be called. This is particularly
useful for output stream I/O.
If a DMA engine needs at least X buffers before it can start streaming, then
for applications to get a buffer out as soon as possible they need to know
the minimum number of buffers to queue before STREAMON can be called. You can't
just try STREAMON after every buffer since on failure STREAMON will dequeue
all your buffers. (Is that a bug or a feature? Frankly, I'm not sure).
This patch simplifies applications substantially: they can just call STREAMON
at the beginning and then start queuing buffers and the DMA engine will
kick in automagically once enough buffers are available.
This also fixes using write() to stream video: the fileio implementation
calls streamon without having any queued buffers, which will fail today for
any driver that requires a minimum number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than taking the mmap semaphore at a relatively high-level function,
push it down to the place where it is really needed.
It was placed in vb2_queue_or_prepare_buf() to prevent racing with other
vb2 calls. The only way I can see that a race can happen is when two
threads queue the same buffer. The solution for that it to introduce
a PREPARING state.
Moving it down offers opportunities to simplify the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both the PAL and NTSC standards are interlaced where a
frame consist of two fields. Total number of lines in a frame in both systems
are an odd number so the two fields will have different length.
In the 625 line standard ("PAL") the odd field of the frame is transmitted first,
while in the 525 standard ("NTSC") the even field is transmitted first.
This adds the possibility to change output config between the fields and standards.
This setting will reduce the "format-jitter" on the signal sent by the pixelport
moving the difference between the fields to vertical front/back-porch only.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added support for YCrCb analog input.
If input is ADV7842_MODE_RGB and RGB quantization range is set to
V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received
as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected.
See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011"
for details.
Make sure that when switching inputs the RGB quantization range is
updated as well.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
May also be wrong if the receiver is connected to more than one connector.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
