commit 67245ff332 upstream.
This gets rid of the horrible notion of having that
struct inode *ptmx_inode
be the linchpin of the interface between the pty code and devpts.
By de-emphasizing the ptmx inode, a lot of things actually get cleaner,
and we will have a much saner way forward. In particular, this will
allow us to associate with any particular devpts instance at open-time,
and not be artificially tied to one particular ptmx inode.
The patch itself is actually fairly straightforward, and apart from some
locking and return path cleanups it's pretty mechanical:
- the interfaces that devpts exposes all take "struct pts_fs_info *"
instead of "struct inode *ptmx_inode" now.
NOTE! The "struct pts_fs_info" thing is a completely opaque structure
as far as the pty driver is concerned: it's still declared entirely
internally to devpts. So the pty code can't actually access it in any
way, just pass it as a "cookie" to the devpts code.
- the "look up the pts fs info" is now a single clear operation, that
also does the reference count increment on the pts superblock.
So "devpts_add/del_ref()" is gone, and replaced by a "lookup and get
ref" operation (devpts_get_ref(inode)), along with a "put ref" op
(devpts_put_ref()).
- the pty master "tty->driver_data" field now contains the pts_fs_info,
not the ptmx inode.
- because we don't care about the ptmx inode any more as some kind of
base index, the ref counting can now drop the inode games - it just
gets the ref on the superblock.
- the pts_fs_info now has a back-pointer to the super_block. That's so
that we can easily look up the information we actually need. Although
quite often, the pts fs info was actually all we wanted, and not having
to look it up based on some magical inode makes things more
straightforward.
In particular, now that "devpts_get_ref(inode)" operation should really
be the *only* place we need to look up what devpts instance we're
associated with, and we do it exactly once, at ptmx_open() time.
The other side of this is that one ptmx node could now be associated
with multiple different devpts instances - you could have a single
/dev/ptmx node, and then have multiple mount namespaces with their own
instances of devpts mounted on /dev/pts/. And that's all perfectly sane
in a model where we just look up the pts instance at open time.
This will eventually allow us to get rid of our odd single-vs-multiple
pts instance model, but this patch in itself changes no semantics, only
an internal binding model.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Francesco Ruggeri <fruggeri@arista.com>
Cc: "Herton R. Krzesinski" <herton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86a574de45 upstream.
Don't allow RNDADDTOENTCNT or RNDADDENTROPY to accept a negative
entropy value. It doesn't make any sense to subtract from the entropy
counter, and it can trigger a warning:
random: negative entropy/overflow: pool input count -40000
------------[ cut here ]------------
WARNING: CPU: 3 PID: 6828 at drivers/char/random.c:670[< none
>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
Modules linked in:
CPU: 3 PID: 6828 Comm: a.out Not tainted 4.7.0-rc4+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
ffffffff880b58e0 ffff88005dd9fcb0 ffffffff82cc838f ffffffff87158b40
fffffbfff1016b1c 0000000000000000 0000000000000000 ffffffff87158b40
ffffffff83283dae 0000000000000009 ffff88005dd9fcf8 ffffffff8136d27f
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff82cc838f>] dump_stack+0x12e/0x18f lib/dump_stack.c:51
[<ffffffff8136d27f>] __warn+0x19f/0x1e0 kernel/panic.c:516
[<ffffffff8136d48c>] warn_slowpath_null+0x2c/0x40 kernel/panic.c:551
[<ffffffff83283dae>] credit_entropy_bits+0x21e/0xad0 drivers/char/random.c:670
[< inline >] credit_entropy_bits_safe drivers/char/random.c:734
[<ffffffff8328785d>] random_ioctl+0x21d/0x250 drivers/char/random.c:1546
[< inline >] vfs_ioctl fs/ioctl.c:43
[<ffffffff8185316c>] do_vfs_ioctl+0x18c/0xff0 fs/ioctl.c:674
[< inline >] SYSC_ioctl fs/ioctl.c:689
[<ffffffff8185405f>] SyS_ioctl+0x8f/0xc0 fs/ioctl.c:680
[<ffffffff86a995c0>] entry_SYSCALL_64_fastpath+0x23/0xc1
arch/x86/entry/entry_64.S:207
---[ end trace 5d4902b2ba842f1f ]---
This was triggered using the test program:
// autogenerated by syzkaller (http://github.com/google/syzkaller)
int main() {
int fd = open("/dev/random", O_RDWR);
int val = -5000;
ioctl(fd, RNDADDTOENTCNT, &val);
return 0;
}
It's harmless in that (a) only root can trigger it, and (b) after
complaining the code never does let the entropy count go negative, but
it's better to simply not allow this userspace from passing in a
negative entropy value altogether.
Google-Bug-Id: #29575089
Reported-By: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d06dd537f upstream.
usbnet_link_change will call schedule_work and should be
avoided if bind is failing. Otherwise we will end up with
scheduled work referring to a netdev which has gone away.
Instead of making the call conditional, we can just defer
it to usbnet_probe, using the driver_info flag made for
this purpose.
Fixes: 8a34b0ae87 ("usbnet: cdc_ncm: apply usbnet_link_change")
Reported-by: Andrey Konovalov <andreyknvl@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a7ae81952c upstream.
Many Intel systems the BIOS declares a SystemIO OpRegion below the SMBus
PCI device as can be seen in ACPI DSDT table from Lenovo Yoga 900:
Device (SBUS)
{
OperationRegion (SMBI, SystemIO, (SBAR << 0x05), 0x10)
Field (SMBI, ByteAcc, NoLock, Preserve)
{
HSTS, 8,
Offset (0x02),
HCON, 8,
HCOM, 8,
TXSA, 8,
DAT0, 8,
DAT1, 8,
HBDR, 8,
PECR, 8,
RXSA, 8,
SDAT, 16
}
There are also bunch of AML methods that that the BIOS can use to access
these fields. Most of the systems in question AML methods accessing the
SMBI OpRegion are never used.
Now, because of this SMBI OpRegion many systems fail to load the SMBus
driver with an error looking like one below:
ACPI Warning: SystemIO range 0x0000000000003040-0x000000000000305F
conflicts with OpRegion 0x0000000000003040-0x000000000000304F
(\_SB.PCI0.SBUS.SMBI) (20160108/utaddress-255)
ACPI: If an ACPI driver is available for this device, you should use
it instead of the native driver
The reason is that this SMBI OpRegion conflicts with the PCI BAR used by
the SMBus driver.
It turns out that we can install a custom SystemIO address space handler
for the SMBus device to intercept all accesses through that OpRegion. This
allows us to share the PCI BAR with the AML code if it for some reason is
using it. We do not expect that this OpRegion handler will ever be called
but if it is we print a warning and prevent all access from the SMBus
driver itself.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110041
Reported-by: Andy Lutomirski <luto@kernel.org>
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19f4c2ba86 upstream.
When setting the operational mode, some third party (Speedlink Strike-FX)
gamepads refuse the output report. Failing here means we refuse to
initialize the gamepad while this should be harmless.
The weird part is that the initial commit that added this: a7de9b8
("HID: sony: Enable Gasia third-party PS3 controllers") mentions this
very same controller as one requiring this output report.
Anyway, it's broken for one user at least, so let's change it.
We will report an error, but at least the controller should work.
And no, these devices present themselves as legacy Sony controllers
(VID:PID of 054C:0268, as in the official ones) so there are no ways
of discriminating them from the official ones.
https://bugzilla.redhat.com/show_bug.cgi?id=1255325
Reported-and-tested-by: Max Fedotov <thesourcehim@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed1f0eeeba upstream.
Add device ID 0x0a04 for Haswell-ULT to the list of devices with MCH
problems.
From a Lenovo ThinkPad T440S:
[ 0.188604] pnp: PnP ACPI init
[ 0.189044] system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.189048] system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
[ 0.189050] system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
[ 0.189052] system 00:00: [mem 0x000c8000-0x000cbfff] could not be reserved
[ 0.189054] system 00:00: [mem 0x000cc000-0x000cffff] could not be reserved
[ 0.189056] system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
[ 0.189058] system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
[ 0.189060] system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
[ 0.189061] system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
[ 0.189063] system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
[ 0.189065] system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
[ 0.189067] system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
[ 0.189069] system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
[ 0.189071] system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.189073] system 00:00: [mem 0x00100000-0xdf9fffff] could not be reserved
[ 0.189075] system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
[ 0.189078] system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
[ 0.189082] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.189216] system 00:01: [io 0x1800-0x189f] could not be reserved
[ 0.189220] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.189222] system 00:01: [io 0x0880-0x08ff] has been reserved
[ 0.189224] system 00:01: [io 0x0900-0x097f] has been reserved
[ 0.189226] system 00:01: [io 0x0980-0x09ff] has been reserved
[ 0.189229] system 00:01: [io 0x0a00-0x0a7f] has been reserved
[ 0.189231] system 00:01: [io 0x0a80-0x0aff] has been reserved
[ 0.189233] system 00:01: [io 0x0b00-0x0b7f] has been reserved
[ 0.189235] system 00:01: [io 0x0b80-0x0bff] has been reserved
[ 0.189238] system 00:01: [io 0x15e0-0x15ef] has been reserved
[ 0.189240] system 00:01: [io 0x1600-0x167f] has been reserved
[ 0.189242] system 00:01: [io 0x1640-0x165f] has been reserved
[ 0.189246] system 00:01: [mem 0xf8000000-0xfbffffff] could not be reserved
[ 0.189249] system 00:01: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.189251] system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.189254] system 00:01: [mem 0xfed10000-0xfed13fff] has been reserved
[ 0.189256] system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.189258] system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.189261] system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
[ 0.189264] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[....]
[ 0.583653] resource sanity check: requesting [mem 0xfed10000-0xfed15fff], which spans more than pnp 00:01 [mem 0xfed10000-0xfed13fff]
[ 0.583654] ------------[ cut here ]------------
[ 0.583660] WARNING: CPU: 0 PID: 1 at arch/x86/mm/ioremap.c:198 __ioremap_caller+0x2c5/0x380()
[ 0.583661] Info: mapping multiple BARs. Your kernel is fine.
[ 0.583662] Modules linked in:
[ 0.583666] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.3.3-303.fc23.x86_64 #1
[ 0.583668] Hardware name: LENOVO 20AR001GXS/20AR001GXS, BIOS GJET86WW (2.36 ) 12/04/2015
[ 0.583670] 0000000000000000 0000000014cf7e59 ffff880214a1baf8 ffffffff813a625f
[ 0.583673] ffff880214a1bb40 ffff880214a1bb30 ffffffff810a07c2 00000000fed10000
[ 0.583675] ffffc90000cb8000 0000000000006000 0000000000000000 ffff8800d6381040
[ 0.583678] Call Trace:
[ 0.583683] [<ffffffff813a625f>] dump_stack+0x44/0x55
[ 0.583686] [<ffffffff810a07c2>] warn_slowpath_common+0x82/0xc0
[ 0.583688] [<ffffffff810a085c>] warn_slowpath_fmt+0x5c/0x80
[ 0.583692] [<ffffffff810a6fba>] ? iomem_map_sanity_check+0xba/0xd0
[ 0.583695] [<ffffffff81065835>] __ioremap_caller+0x2c5/0x380
[ 0.583698] [<ffffffff81065907>] ioremap_nocache+0x17/0x20
[ 0.583701] [<ffffffff8103a119>] snb_uncore_imc_init_box+0x79/0xb0
[ 0.583705] [<ffffffff81038900>] uncore_pci_probe+0xd0/0x1b0
[ 0.583707] [<ffffffff813efda5>] local_pci_probe+0x45/0xa0
[ 0.583710] [<ffffffff813f118d>] pci_device_probe+0xfd/0x140
[ 0.583713] [<ffffffff814d9b52>] driver_probe_device+0x222/0x480
[ 0.583715] [<ffffffff814d9e34>] __driver_attach+0x84/0x90
[ 0.583717] [<ffffffff814d9db0>] ? driver_probe_device+0x480/0x480
[ 0.583720] [<ffffffff814d762c>] bus_for_each_dev+0x6c/0xc0
[ 0.583722] [<ffffffff814d930e>] driver_attach+0x1e/0x20
[ 0.583724] [<ffffffff814d8e4b>] bus_add_driver+0x1eb/0x280
[ 0.583727] [<ffffffff81d6af1a>] ? uncore_cpu_setup+0x12/0x12
[ 0.583729] [<ffffffff814da680>] driver_register+0x60/0xe0
[ 0.583733] [<ffffffff813ef78c>] __pci_register_driver+0x4c/0x50
[ 0.583736] [<ffffffff81d6affc>] intel_uncore_init+0xe2/0x2e6
[ 0.583738] [<ffffffff81d6af1a>] ? uncore_cpu_setup+0x12/0x12
[ 0.583741] [<ffffffff81002123>] do_one_initcall+0xb3/0x200
[ 0.583745] [<ffffffff810be500>] ? parse_args+0x1a0/0x4a0
[ 0.583749] [<ffffffff81d5c1c8>] kernel_init_freeable+0x189/0x223
[ 0.583752] [<ffffffff81775c40>] ? rest_init+0x80/0x80
[ 0.583754] [<ffffffff81775c4e>] kernel_init+0xe/0xe0
[ 0.583758] [<ffffffff81781adf>] ret_from_fork+0x3f/0x70
[ 0.583760] [<ffffffff81775c40>] ? rest_init+0x80/0x80
[ 0.583765] ---[ end trace 077c426a39e018aa ]---
00:00.0 Host bridge [0600]: Intel Corporation Haswell-ULT DRAM Controller [8086:0a04] (rev 0b)
Subsystem: Lenovo Device [17aa:220c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: hsw_uncore
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1300955
Tested-by: <robo@tcp.sk>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 221255aee6 upstream.
device handler initialisation might fail due to a number of
reasons. But as device_handlers are optional this shouldn't
cause us to disable the device entirely.
So just ignore errors from scsi_dh_add_device().
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e6bd18f57a ("IB/security: Restrict use of the write()
interface") fixed a security problem with various write()
implementations in the Infiniband subsystem. In older kernel versions
the ipath_write() function has the same problem and needs the same
restriction. (The ipath driver has been completely removed upstream.)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e86663c475 ]
Nothing is decrementing the index "i" while we are cleaning up the
fragments we could not successful transmit.
Fixes: 9cde94506e ("bgmac: implement scatter/gather support")
Reported-by: coverity (CID 1352048)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 005db31d5f ]
Commit e826eafa65 ("bonding: Call netif_carrier_off after
register_netdevice") moved netif_carrier_off() from bond_init() to
bond_create(), but the latter is called only for initial default
devices and ones created through sysfs:
$ modprobe bonding
$ echo +bond1 > /sys/class/net/bonding_masters
$ ip link add bond2 type bond
$ grep "MII Status" /proc/net/bonding/*
/proc/net/bonding/bond0:MII Status: down
/proc/net/bonding/bond1:MII Status: down
/proc/net/bonding/bond2:MII Status: up
Ensure that carrier is initially off also for devices created through
netlink.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a36aa80f3c upstream.
Driver initialization tries to request a hub (GTH) driver module from
its probe callback, resulting in a deadlock.
This patch solves the problem by adding a deferred work for requesting
the hub module.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a1a47ce35 upstream.
This adds Intel(R) Trace Hub PCI ID for Kaby Lake PCH-H.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06708f8152 upstream.
Commit aebea2ba0f ("net: mvneta: fix Tx interrupt delay") intended to
set coalescing threshold to a value guaranteeing interrupt generation
per each sent packet, so that buffers can be released with no delay.
In fact setting threshold to '1' was wrong, because it causes interrupt
every two packets. According to the documentation a reason behind it is
following - interrupt occurs once sent buffers counter reaches a value,
which is higher than one specified in MVNETA_TXQ_SIZE_REG(q). This
behavior was confirmed during tests. Also when testing the SoC working
as a NAS device, better performance was observed with int-per-packet,
as it strongly depends on the fact that all transmitted packets are
released immediately.
This commit enables NETA controller work in interrupt per sent packet mode
by setting coalescing threshold to 0.
Signed-off-by: Dmitri Epshtein <dima@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes aebea2ba0f ("net: mvneta: fix Tx interrupt delay")
Acked-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22ebf00eb5 upstream.
of_address_to_resource return 0 on successful call but
devm_ioremap_resource is called only if it returns non-zero value
Signed-off-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aa93d1fee8 upstream.
Fix a memory leak on probe error of the airspy usb device driver.
The problem is triggered when more than 64 usb devices register with
v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
A badusb device can emulate 64 of these devices, and then through
continual emulated connect/disconnect of the 65th device, cause the
kernel to run out of RAM and crash the kernel, thus causing a local DOS
vulnerability.
Fixes CVE-2016-5400
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54e430bbd4 upstream.
If we fall back to using LSI on the Croc or Crocodile chip we need to
clear the interrupt so we don't hang the system.
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e7ff2ca7f upstream.
Commit b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
changed the way vendor- and model-string matching was carried out in the
routine that looks up entries in a SCSI devinfo list. The new matching
code failed to take into account the case of a maximum-length string; in
such cases it could end up testing for a terminating '\0' byte beyond
the end of the memory allocated to the string. This out-of-bounds bug
was detected by UBSAN.
I don't know if anybody has actually encountered this bug. The symptom
would be that a device entry in the blacklist might not be matched
properly if it contained an 8-character vendor name or a 16-character
model name. Such entries certainly exist in scsi_static_device_list.
This patch fixes the problem by adding a check for a maximum-length
string before the '\0' test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: b704f70ce2 ("SCSI: fix bug in scsi_dev_info_list matching")
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25e1ed6e64 upstream.
For 'real' hardware CAN devices the netlink interface is used to set CAN
specific communication parameters. Real CAN hardware can not be created nor
removed with the ip tool ...
This patch adds a private dellink function for the CAN device driver interface
that does just nothing.
It's a follow up to commit 993e6f2fd ("can: fix oops caused by wrong rtnl
newlink usage") but for dellink.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bce271f255 upstream.
With upstream commit bb208f144c (can: fix handling of unmodifiable
configuration options) a new can_validate() function was introduced.
When invoking 'ip link set can0 type can' without any configuration data
can_validate() tries to validate the content without taking into account that
there's totally no content. This patch adds a check for missing content.
Reported-by: ajneu <ajneu1@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 427460c83c upstream.
When testing CAN write floods on Altera's CycloneV, the first 2 bytes
are sometimes 0x00, 0x00 or corrupted instead of the values sent. Also
observed bytes 4 & 5 were corrupted in some cases.
The D_CAN Data registers are 32 bits and changing from 16 bit writes to
32 bit writes fixes the problem.
Testing performed on Altera CycloneV (D_CAN). Requesting tests on other
C_CAN & D_CAN platforms.
Reported-by: Richard Andrysek <richard.andrysek@gomtec.de>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43200a4480 upstream.
At high bus load it could happen that "at91_poll()" enters with all RX
message boxes filled up. If then at the end the "quota" is exceeded as
well, "rx_next" will not be reset to the first RX mailbox and hence the
interrupts remain disabled.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Amr Bekhit <amrbekhit@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f68381a70b upstream.
The code that fills packed command header assumes that CPU runs in
little-endian mode. Hence the header is malformed in big-endian mode
and causes MMC data transfer errors:
[ 563.200828] mmcblk0: error -110 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc40
[ 563.219647] mmcblk0: packed cmd failed, nr 2, sectors 16, failure index: -1
Convert header data to LE.
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Fixes: ce39f9d17c ("mmc: support packed write command for eMMC4.5 devices")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7831b4ff0d upstream.
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9c ("qeth: NAPI support for l2 and l3 discipline")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 096cdc6f52 upstream.
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445 ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 595144c114 upstream.
The flags element of clk_init_data was never initialized for mmc-
phase-clocks resulting in the element containing a random value
and thus possibly enabling unwanted clock flags.
Fixes: 89bf26cbc1 ("clk: rockchip: Add support for the mmc clock phases using the framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d9fe44bd7 upstream.
When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.
Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 719bd65420 upstream.
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bc28b93a3 upstream.
Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:
[ 1.452598] power_supply_read_temp+0x78/0x80
[ 1.458680] thermal_zone_get_temp+0x5c/0x11c
[ 1.464765] thermal_zone_device_update+0x34/0xb4
[ 1.471195] thermal_zone_device_register+0x87c/0x8cc
[ 1.477974] __power_supply_register+0x364/0x424
[ 1.484317] power_supply_register_no_ws+0x10/0x18
[ 1.490833] bq27xxx_battery_setup+0x10c/0x164
[ 1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[ 1.503435] i2c_device_probe+0x174/0x240
[ 1.509172] driver_probe_device+0x1fc/0x29c
[ 1.515167] __driver_attach+0xa4/0xa8
[ 1.520643] bus_for_each_dev+0x58/0x98
[ 1.526204] driver_attach+0x20/0x28
[ 1.531505] bus_add_driver+0x1c8/0x22c
[ 1.537067] driver_register+0x68/0x108
[ 1.542630] i2c_register_driver+0x38/0x7c
[ 1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[ 1.555321] do_one_initcall+0x38/0x12c
[ 1.560886] kernel_init_freeable+0x148/0x1ec
[ 1.566972] kernel_init+0x10/0xfc
[ 1.572101] ret_from_fork+0x10/0x40
Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba562d5e54 upstream.
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ac3c0a402 upstream.
With many repeated suspend resume cycles, the pin specific wakeirq
may not always work on omaps. This is because the write to enable the
pin interrupt may not have reached the device over the interconnect
before suspend happens.
Let's fix the issue with a flush of posted write with a readback.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9003c9cfa upstream.
Passes input_id struct to the common probe function for the tsc200x drivers
instead of just the bustype.
This allows for the use of the product variable to set the input_dev->name
variable according to the type of touchscreen used. Note that when we
introduced support for TSC2004 we started calling everything TSC200X, so
let's keep this quirk.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit caca925fca upstream.
This prevents a malicious USB device from causing an oops.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12afb34400 upstream.
Somehow the patch that added two-finger touch support forgot to update
W8001_MAX_LENGTH from 11 to 13.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7f1429389 upstream.
Xbox One controllers have multiple interfaces which all have the
same class, subclass, and protocol. One of the these interfaces
has only a single endpoint. When Xpad attempts to bind to this
interface, it causes an oops when trying initialize the output URB
by trying to access the second endpoint's descriptor.
This situation was avoided for known Xbox One devices by checking
the XTYPE constant associated with the VID and PID tuple. However,
this breaks when new or previously unknown Xbox One controllers
are attached to the system.
This change addresses the problem by deriving the XTYPE for Xbox
One controllers based on the interface protocol before checking
the interface number.
Fixes: 1a48ff81b3 ("Input: xpad - add support for Xbox One controllers")
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 226ba70774 upstream.
The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and
according to Elan both 11 and 12 are valid IC types and should be
identified as hw_version 4.
Reported-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Tested-by: Patrick Lessard <Patrick.Lessard@cogeco.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60842ef812 upstream.
The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This
causes the port to be reserved by the APCI module as the system comes up,
making it unavailable to be reserved again by other drivers, thus
preserving this VMWare port for special use in a VMWare guest.
This port is designed to be shared among multiple VMWare services, such as
the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port
on its own.
The VMWare non-EFI BIOS does not do this to preserve compatibility with
existing/legacy VMs. It is known that there is small chance a VM may be
configured such that these ports get reserved by other non-VMWare devices,
and if this ever happens, the result is undefined.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7469be95a4 upstream.
xenbus_dev_request_and_reply() needs to track whether a transaction is
open. For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().
If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.
If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.
Commit 027bd7e899 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open. This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.
It appears that the problematic change was added accidentally, so just
remove it.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0beef634b8 upstream.
Inability to locate a user mode specified transaction ID should not
lead to a kernel crash. For other than XS_TRANSACTION_START also
don't issue anything to xenbus if the specified ID doesn't match that
of any active transaction.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02ef871eca upstream.
Current overlap check is evaluating to false a case where a filter
field is fully contained (proper subset) of a r/w request. This
change applies classical overlap check instead to include all the
scenarios.
More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver
the logic is such that the entire confspace is read and written in 4
byte chunks. In this case as an example, CACHE_LINE_SIZE,
LATENCY_TIMER and PCI_BIST are arriving together in one call to
xen_pcibk_config_write() with offset == 0xc and size == 4. With the
exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length
== 1) is fully contained in the write request and hence is excluded
from write, which is incorrect.
Signed-off-by: Andrey Grodzovsky <andrey2805@gmail.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 368301f2fe upstream.
With this command sequence:
modprobe plip
modprobe pps_parport
rmmod pps_parport
the partport_pps modules causes this crash:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: parport_detach+0x1d/0x60 [pps_parport]
Oops: 0000 [#1] SMP
...
Call Trace:
parport_unregister_driver+0x65/0xc0 [parport]
SyS_delete_module+0x187/0x210
The sequence that builds up to this is:
1) plip is loaded and takes the parport device for exclusive use:
plip0: Parallel port at 0x378, using IRQ 7.
2) pps_parport then fails to grab the device:
pps_parport: parallel port PPS client
parport0: cannot grant exclusive access for device pps_parport
pps_parport: couldn't register with parport0
3) rmmod of pps_parport is then killed because it tries to access
pardev->name, but pardev (taken from port->cad) is NULL.
So add a check for NULL in the test there too.
Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9295c41d77 upstream.
Due to the way CUBC register is updated, a double flush is needed to
compute an accurate residue. First flush aim is to get data from the DMA
FIFO and second one ensures that we won't report data which are not in
memory.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53398f4888 upstream.
An unexpected value of CUBC can lead to a corrupted residue. A more
complex sequence is needed to detect an inaccurate value for NCA or CUBC.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abb2bafd29 upstream.
The EFI firmware on Macs contains a full-fledged network stack for
downloading OS X images from osrecovery.apple.com. Unfortunately
on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331
wireless card on every boot and leaves it enabled even after
ExitBootServices has been called. The card continues to assert its IRQ
line, causing spurious interrupts if the IRQ is shared. It also corrupts
memory by DMAing received packets, allowing for remote code execution
over the air. This only stops when a driver is loaded for the wireless
card, which may be never if the driver is not installed or blacklisted.
The issue seems to be constrained to the Broadcom 4331. Chris Milsted
has verified that the newer Broadcom 4360 built into the MacBookPro11,3
(2013/2014) does not exhibit this behaviour. The chances that Apple will
ever supply a firmware fix for the older machines appear to be zero.
The solution is to reset the card on boot by writing to a reset bit in
its mmio space. This must be done as an early quirk and not as a plain
vanilla PCI quirk to successfully combat memory corruption by DMAed
packets: Matthew Garrett found out in 2012 that the packets are written
to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html).
This type of memory is made available to the page allocator by
efi_free_boot_services(). Plain vanilla PCI quirks run much later, in
subsys initcall level. In-between a time window would be open for memory
corruption. Random crashes occurring in this time window and attributed
to DMAed packets have indeed been observed in the wild by Chris
Bainbridge.
When Matthew Garrett analyzed the memory corruption issue in 2012, he
sought to fix it with a grub quirk which transitions the card to D3hot:
http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56
This approach does not help users with other bootloaders and while it
may prevent DMAed packets, it does not cure the spurious interrupts
emanating from the card. Unfortunately the card's mmio space is
inaccessible in D3hot, so to reset it, we have to undo the effect of
Matthew's grub patch and transition the card back to D0.
Note that the quirk takes a few shortcuts to reduce the amount of code:
The size of BAR 0 and the location of the PM capability is identical
on all affected machines and therefore hardcoded. Only the address of
BAR 0 differs between models. Also, it is assumed that the BCMA core
currently mapped is the 802.11 core. The EFI driver seems to always take
care of this.
Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback
towards finding the best solution to this problem.
The following should be a comprehensive list of affected models:
iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16]
iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16]
Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12]
Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12]
Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12]
MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12]
MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12]
MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12]
For posterity, spurious interrupts caused by the Broadcom 4331 wireless
card resulted in splats like this (stacktrace omitted):
irq 17: nobody cared (try booting with the "irqpoll" option)
handlers:
[<ffffffff81374370>] pcie_isr
[<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci]
[<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec]
Disabling IRQ #17
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732
Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1]
Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1]
Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2]
Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1]
Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Chris Milsted <cmilsted@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: b43-dev@lists.infradead.org
Cc: linux-pci@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de
[ Did minor readability edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c66f59ee50 upstream.
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34511dce4b upstream.
It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.
This is a manual revert of commits 5fa836a9d8 ("drm/i915: DP link
training optimization") and 4e96c97742 ("drm/i915: eDP link training
optimization").
Fixes: 5fa836a9d8 ("drm/i915: DP link training optimization")
Fixes: 4e96c97742 ("drm/i915: eDP link training optimization")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
(cherry picked from commit 91df09d92a)
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
