Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The non-PCI builds of the O day test project are failing:
On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)
The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies. To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b840c3627b
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Contrary to what the datasheet says, the pre divider doesn't seem to be
incremented by one in the PLL2, but just uses the value from the register,
with 0 being a bypass.
This fixes the audio playing too fast.
Since we now have the same pre-divider flags, and the only difference with
the A10 is the post-divider offset, also remove the structure to just pass
the offset as an argument.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: eb662f8547 ("clk: sunxi: pll2: Add A13 support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The sun9i usb phy driver calls of_usb_get_phy_mode(), which is not
available if USB is disabled:
drivers/built-in.o: In function `sun9i_usb_phy_probe':
:(.text+0x7fb0): undefined reference to `of_usb_get_phy_mode'
This adds a dependency to avoid the randconfig build errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c3b443026 ("phy: Add driver to support individual USB PHYs on sun9i")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e328941 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
There's one fix for the core here, we weren't reinitialising the actual
transferred length in messages when they get reused which meant that
we'd just keep adding to the length if a message is reused. This has
limited impact since it's only used in error handling cases but will
really mess anything that tries to use it up when it triggers.
As ever there's a small collection of driver specific fixes too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWXaUPAAoJECTWi3JdVIfQLPAH/1A6xgPcS2HnBu43ezzQu9JY
gd22gYN1+klyKhOzWv86zG0vbT/sVo2YCTb8nbnGfMCc5ghwlxF1fl2mCVXRTr2F
7dP2n43TmTNsuXQjO4tv2iJTkCXXuhoEr3DTrOu3+ywm+HNn1gUPgOl0i7zZpuIJ
AcQ0uuh33k5nQW3elj/gFcdjlVdHIq5oNpP4JBJeOn+ijsd/6DzVyW+TBiGnImWX
50XCuM+gUvj762y77T3rgORkWwkmJSQIjV+TNKXD/hIDvVWQK9OvtyMpGBOTe7nH
emEiy7BJnVIdpknUUVf0ZqjNpprxpLwU+ryQhVC9orP0dL64GlsbPkFOtIgxkDs=
=NlLa
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix for the core here, we weren't reinitialising the
actual transferred length in messages when they get reused which meant
that we'd just keep adding to the length if a message is reused. This
has limited impact since it's only used in error handling cases but
will really mess anything that tries to use it up when it triggers.
As ever there's a small collection of driver specific fixes too"
* tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bugfix: spi_message.transfer_length does not get reset
spi: pl022: handle EPROBE_DEFER for dma
spi: bcm63xx: use correct format string for printing a resource
spi: mediatek: single device does not require cs_gpios
spi: Add missing kerneldoc description for parameter
A small copy and paste error was preventing the haptics device being
disabled. This patch corrects the value written on disable.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For cpufreq drivers which use setpolicy interface, after offline->online
the policy is set to default. This can be reproduced by setting the
default policy of intel_pstate or longrun to ondemand and then change to
"performance". After offline and online, the setpolicy will be called with
the policy=ondemand.
For drivers using governors this condition is handled by storing
last_governor, during offline and restoring during online. The same should
be done for drivers using setpolicy interface. Storing last_policy during
offline and restoring during online.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as we leave the spinlock after the job has been added to the job
queue, we can no longer rely on the job's data to be available.
I have seen a null-pointer dereference due to sched == NULL in
amd_sched_wakeup via amd_sched_entity_push_job and
amd_sched_ib_submit_kernel_helper. Since the latter initializes
sched_job->sched with the address of the ring scheduler, which is
guaranteed to be non-NULL, this race appears to be a likely culprit.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=93079
Reviewed-by: Christian König <christian.koenig@amd.com>
Missing error check if the operation failed.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The SCSI sd driver probes SCSI devices asynchronously. The sd_remove()
function, called indirectly by device_del(), waits until asynchronous
probing has finished. Since the block layer queue must only be cleaned
up after probing has finished, device_del() has to be called before
blk_cleanup_queue(). Hence revert commit bf2cf3baa2.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Pull HID fixes from Jiri Kosina:
- regression fix for hid-lg driver from Benjamin Tissoires
- quirk for Logitech G710+ from Jimmy Berry
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: lg: restrict filtering out of first interface to G29 only
HID: usbhid: add Logitech G710+ keyboard quirk NOGET
- Drop a redundant if-clause from Kconfig
- Fix a missing of_node_put() memory leak in the
Freescale i.MX driver
- Fix 64bit compilation of the Qualcomm SSBI driver.
- Fix a logic inversion in the Mediatek driver.
- Fix a compilation error for the odd one off in the
Super-H instance of the SH PFC driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f61M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol fixes from Linus Walleij:
"These are some v4.4 pin control fixes:
- Drop a redundant if-clause from Kconfig
- Fix a missing of_node_put() memory leak in the Freescale i.MX
driver
- Fix 64bit compilation of the Qualcomm SSBI driver.
- Fix a logic inversion in the Mediatek driver.
- Fix a compilation error for the odd one off in the Super-H instance
of the SH PFC driver"
* tag 'pinctrl-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sh-pfc: sh7734: Add missing cfg macro parameter to fix build
pinctrl: mediatek: Add get_direction support.
pinctrl: fix qcom ssbi drivers for 64-bit compilation
pinctrl: imx1-core: add missing of_node_put
pinctrl: remove redundant if conditional from Kconfig
- Fix a bunch of possible NULL references found by Coccinelle
jockeys.
- Stop creating Tegra's debugfs on everything and it's dog.
This is an ARM multiplatform kernel issue.
- Fix an oops in gpiolib for NULL names on named GPIOs.
- Fix a complex OMAP1 bug in the OMAP driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aggl
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.4 series:
- Fix a bunch of possible NULL references found by Coccinelle
jockeys.
- Stop creating Tegra's debugfs on everything and its dog. This is
an ARM multiplatform kernel issue.
- Fix an oops in gpiolib for NULL names on named GPIOs.
- Fix a complex OMAP1 bug in the OMAP driver"
* tag 'gpio-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: drop omap1 mpuio specific irq_mask/unmask callbacks
gpiolib: fix oops, if gpio name is NULL
gpio-tegra: Do not create the debugfs entry by default
gpio: palmas: fix a possible NULL dereference
gpio: syscon: fix a possible NULL dereference
gpio: 74xx: fix a possible NULL dereference
dm_btree_remove_leaves() only unmaps a contiguous region so we need a
loop, in __remove_range(), to handle ranges that contain multiple
regions.
A new btree function, dm_btree_lookup_next(), is introduced which is
more efficiently able to skip over regions of the thin device which
aren't mapped. __remove_range() uses dm_btree_lookup_next() for each
iteration of __remove_range()'s loop.
Also, improve description of dm_btree_remove_leaves().
Fixes: 6550f075 ("dm thin metadata: add dm_thin_remove_range()")
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.1+
The block allocated at the start of btree_split_sibling() is never
released if later insert_at() fails.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
The aiptek driver crashes in aiptek_probe() when a specially crafted USB
device without endpoints is detected. This fix adds a check that the device
has proper configuration expected by the driver. Also an error return value
is changed to more matching one in one of the error paths.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently people are installing generic Linux distributions not only on
Pixels but also on other Chromebooks. Unfortunately on all of them Atmel
parts assigned names ATML0000 and ATML0001, and do not carry any other
configuration data. So let's create generic instance of platform data that
should cover most of them (we assume that they will not be using T100
objects, since with those Google mapped BTN_LEFT onto a different GPIO, so
slightly different keymap would be needed, but I think we used parts with
T100 on ARM devices where we thankfully have DTS and can describe the
devices better).
Tested-by: Rich K <rgkirch@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are platforms that don't need the full GMBUS power domain (BXT)
while others do (PCH, VLV/CHV). For optimizing this we would need to add
a new power domain, but it's not clear how much we would benefit given
the short time we hold the reference. So for now let's keep things
simple.
This fixes a regression introduced in
commit 237ed86c69
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Tue Sep 15 09:44:20 2015 +0530
drm/i915: Check live status before reading edid
v2:
- fix commit message, PCH won't take any redundant power resource after
this change (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[fix commit message in v2 (Imre)]
[Cherry-picked from drm-intel-next-queued 29bb94bb (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-6-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MISSING_CASE() would have been useful to track down a recent problem in
intel_display_port_aux_power_domain(), so add it there and a few related
helpers. This was also suggested by Ville in his review of the latest
DMC/DC changes, we forgot to address that.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued b9fec167 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-5-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Due to the current sharing of the DDI encoder between DP and HDMI
connectors we can run the DP detection after the HDMI detection has
already set the shared encoder's type. For now solve this keeping the
current behavior and running the detection in this case too. For a proper
solution Ville suggested to split the encoder into an HDMI and DP one, that
can be done as a follow-up.
This issue triggers the WARN in intel_display_port_aux_power_domain() and
was introduced in:
commit 25f78f58e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Nov 16 15:01:04 2015 +0100
drm/i915: Clean up AUX power domain handling
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 651174a4 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-4-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued f0ab43e6 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-3-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 25f78f58 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-2-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The runtime PM core doesn't treat EBUSY and EAGAIN retvals from the driver
suspend hooks as errors, but they still show up as errors in dmesg. Tune
them down. See rpm_suspend() for details of handling these return values.
Note that we use dev_dbg() for the retryable retvals, so after this
change you'll need either CONFIG_DYNAMIC_DEBUG or CONFIG_PCI_DEBUG
for them to show up in the log.
One problem caused by this was noticed by Daniel: the i915 driver
returns EAGAIN to signal a temporary failure to suspend and as a request
towards the RPM core for scheduling a suspend again. This is a normal
event, but the resulting error message flags a breakage during the
driver's automated testing which parses dmesg and picks up the error.
Reported-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://bugs.freedesktop.org/show_bug.cgi?id=92992
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Recently genpd removed the requirement of a having a driver bound for its
attached devices to allow genpd to power off. That change should also have
removed a corresponding validation in the governor, let's correct that.
Fixes: 298cd0f088 (PM / Domains: Remove dev->driver check for runtime)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a CPU is offlined, there may be unprocessed events on a port for
that CPU. If the port is subsequently reused on a different CPU, it
could be in an unexpected state with the link bit set, resulting in
interrupts being missed. Fix this by consuming any unprocessed events
for a particular CPU when that CPU dies.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: David Vrabel <david.vrabel@citrix.com>